kernel/git/next/linux-next.git/drivers/phy/broadcom/phy-brcm-usb-init-synopsys.c, branch master

phy: usb: add support for bcm74110

2025-04-11T07:21:13+00:00

bcm74110 adds a freerun utmi/ref clock that saves further power during suspend states. A tune is also necessary to pass USB compliance test. Signed-off-by: Justin Chen Reviewed-by: Florian Fainelli Link: https://lore.kernel.org/r/20250402185159.2976920-3-justin.chen@broadcom.com Signed-off-by: Vinod Koul

phy: usb: Toggle the PHY power during init

2024-12-04T14:15:35+00:00

When bringing up the PHY, it might be in a bad state if left powered. One case is we lose the PLL lock if the PLL is gated while the PHY is powered. Toggle the PHY power so we can start from a known state. Fixes: 4e5b9c9a73b3 ("phy: usb: Add support for new Synopsys USB controller on the 7216") Signed-off-by: Justin Chen Acked-by: Florian Fainelli Link: https://lore.kernel.org/r/20241024213540.1059412-1-justin.chen@broadcom.com Signed-off-by: Vinod Koul

phy: usb: disable COMMONONN for dual mode

2024-10-11T08:26:25+00:00

The COMMONONN bit suspends the phy when the port is put into a suspend state. However when the phy is shared between host and device in dual mode, this no longer works cleanly as there is no synchronization between the two. Fixes: 5095d045a962 ("phy: usb: Turn off phy when port is in suspend") Signed-off-by: Justin Chen Acked-by: Florian Fainelli Link: https://lore.kernel.org/r/20241010185344.859865-1-justin.chen@broadcom.com Signed-off-by: Vinod Koul

phy: usb: Turn off phy when port is in suspend

2023-06-21T12:13:27+00:00

The COMMONONN bit turns off the PHY when the host controller puts it into suspend state. This can happen during the following... - Nothing is connected to the port - The host controller goes into low power mode whatever due to auto suspend or system suspend. With COMMONONN we also must unset U2_FREECLK_EXISTS since the UTMI clock is fed by the PHY. With these changes we see a power savings of ~12mW when port is in suspend. Reviewed-by: Florian Fainelli Signed-off-by: Justin Chen Link: https://lore.kernel.org/r/1686859578-45242-2-git-send-email-justin.chen@broadcom.com Signed-off-by: Vinod Koul

phy: usb: Fix clock imbalance for suspend/resume

2022-11-07T04:50:25+00:00

We should be disabling clocks when wake from USB is not needed. Since this wasn't done, we had a clock imbalance since clocks were always being enabled on resume. Fixes: ae532b2b7aa5 ("phy: usb: Add "wake on" functionality for newer Synopsis XHCI controllers") Fixes: b0c0b66c0b43 ("phy: usb: Add support for wake and USB low power mode for 7211 S2/S5") Signed-off-by: Justin Chen Acked-by: Florian Fainelli Link: https://lore.kernel.org/r/1665005418-15807-7-git-send-email-justinpopo6@gmail.com Signed-off-by: Vinod Koul

phy: usb: Use slow clock for wake enabled suspend

2022-11-07T04:50:25+00:00

The logic was incorrect when switching to slow clock. We want the slow clock if wake_enabled is set. Fixes: ae532b2b7aa5 ("phy: usb: Add "wake on" functionality for newer Synopsis XHCI controllers") Signed-off-by: Justin Chen Acked-by: Florian Fainelli Link: https://lore.kernel.org/r/1665005418-15807-6-git-send-email-justinpopo6@gmail.com Signed-off-by: Vinod Koul

phy: usb: Disable phy auto-suspend

2022-11-07T04:50:24+00:00

The BDC block requires the PLL lock in order to grab the PLL clock. The phy auto-suspend feature turns off the phy when nothing is attached leading to the PLL to not lock. This leads the BDC block to grab the AUX clock instead of the PLL clock. This is not ideal, so lets turn this feature off. Signed-off-by: Justin Chen Acked-by: Florian Fainelli Link: https://lore.kernel.org/r/1665005418-15807-5-git-send-email-justinpopo6@gmail.com Signed-off-by: Vinod Koul

phy: usb: Migrate to BIT and BITMASK macros

2022-11-07T04:50:24+00:00

Using BIT and BITMASK macros makes it much easier to read and make modifications. Also reordered some constants to be in numerical order. Signed-off-by: Justin Chen Acked-by: Florian Fainelli Link: https://lore.kernel.org/r/1665005418-15807-4-git-send-email-justinpopo6@gmail.com Signed-off-by: Vinod Koul

phy: usb: Improve port mode selection

2022-11-05T07:42:55+00:00

Split port modes into two different variables. Supported port modes is what the hardware supports. While port mode is how the hardware is currently configured and can be dynamically changed through the sysfs. We initialize all supported port modes on init even though the port mode may not be selected because we cannot guarantee the downstream interface from the phy will be active or not. This also fixes an issue where port modes selected via sysfs were not being saved through suspend/resume. Signed-off-by: Justin Chen Acked-by: Florian Fainelli Link: https://lore.kernel.org/r/1665005418-15807-2-git-send-email-justinpopo6@gmail.com Signed-off-by: Vinod Koul

phy: usb: Add "wake on" functionality for newer Synopsis XHCI controllers

2022-02-25T08:43:19+00:00

Add "wake on" support for the newer Synopsis based XHCI only controller. This works on the 72165 and 72164 and newer chips and does not work on 7216 based systems. Also switch the USB sysclk to a slower clock on suspend to save additional power in S2. The clock switch will only save power on the 72165b0 and newer chips and is a nop on older chips. Signed-off-by: Al Cooper Signed-off-by: Florian Fainelli Link: https://lore.kernel.org/r/20220215032422.5179-1-f.fainelli@gmail.com Signed-off-by: Vinod Koul