| Age | Commit message (Collapse) | Author |
|---|
|
Make sure to release the sibling interfaces in case controller
registration fails to avoid use-after-free and double-free when they are
eventually disconnected.
This issue was reported by Sashiko while reviewing a fix for a wakeup
source leak in the btusb probe errors paths.
Link: https://sashiko.dev/#/patchset/20260402092704.2346710-1-johan%40kernel.org
Fixes: 9bfa35fe422c ("[Bluetooth] Add SCO support to btusb driver")
Fixes: 9d08f50401ac ("Bluetooth: btusb: Add support for Broadcom LM_DIAG interface")
Cc: stable@vger.kernel.org # 2.6.27
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
When btmtk_isopkt_pad() fails, the previously allocated URB is not freed,
leaking the urb structure. Add usb_free_urb() before returning the error.
Fixes: ceac1cb0259d ("Bluetooth: btusb: mediatek: add ISO data transmission functions")
Signed-off-by: Zhao Dongdong <zhaodongdong@kylinos.cn>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add USB ID 2357:0607 for TP-Link TL-UB250.
This is a Realtek RTL8761BUV based Bluetooth adapter.
Without this entry the device is picked up by the generic Bluetooth USB
class match and exposes hci0, but the Realtek setup path is not used and
rtl8761bu firmware/config are not loaded.
The controller reports Realtek Semiconductor Corporation as the
manufacturer and LMP subversion 0x8761. With this entry added, btusb
loads rtl_bt/rtl8761bu_fw.bin and rtl_bt/rtl8761bu_config.bin
successfully.
Relevant part of /sys/kernel/debug/usb/devices:
T: Bus=01 Lev=02 Prnt=06 Port=00 Cnt=01 Dev#= 9 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=2357 ProdID=0607 Rev= 2.00
S: Product=TP-Link TL-UB250 Adapter
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
Use the same flags as the existing TP-Link 2357:0604 entry.
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Cris <cxs1494089474@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
These NICs are often reported to lose their Bluetooth interfaces, i.e,
their USB interfaces suddenly become completely unresponsive, causing
the USB core to reset them, only to find that they are no longer
accessible. A power cycle is required to make the Bluetooth interfaces
recover.
After some investigations, I found that their USB autosuspend remote
wakeup capabilities are so broken that they are precisely the culprit
behind the issue:
[27452.608056] hub 3-0:1.0: state 7 ports 5 chg 0000 evt 0020
[27452.702018] usb 3-5: usb wakeup-resume
[27452.716038] usb 3-5: Waited 0ms for CONNECT
[27452.716642] usb 3-5: finish resume
/* usbmon showed that the device was completely unresponsive to any
URBs after the remote wakeup */
[27457.836030] usb 3-5: retry with reset-resume
[27457.956046] usb 3-5: reset high-speed USB device number 4 using xhci_hcd
[27463.332047] usb 3-5: device descriptor read/64, error -110
[27478.948117] usb 3-5: device descriptor read/64, error -110
[27479.172430] usb 3-5: reset high-speed USB device number 4 using xhci_hcd
[27484.332035] usb 3-5: device descriptor read/64, error -110
[27499.940039] usb 3-5: device descriptor read/64, error -110
[27500.164060] usb 3-5: reset high-speed USB device number 4 using xhci_hcd
[27505.196142] xhci_hcd 0000:67:00.0: Timeout while waiting for setup device command
[27510.576045] xhci_hcd 0000:67:00.0: Timeout while waiting for setup device command
[27510.784038] usb 3-5: device not accepting address 4, error -62
[27510.912215] usb 3-5: reset high-speed USB device number 4 using xhci_hcd
[27515.948307] xhci_hcd 0000:67:00.0: Timeout while waiting for setup device command
[27521.324380] xhci_hcd 0000:67:00.0: Timeout while waiting for setup device command
[27521.525107] usb 3-5: device not accepting address 4, error -62
[27521.525928] usb usb3-port5: logical disconnect
[27521.525996] usb 3-5: gone after usb resume? status -19
[27521.526230] usb 3-5: can't resume, status -19
[27521.526434] usb usb3-port5: logical disconnect
[27521.526469] usb usb3-port5: resume, status -19
[27521.526493] usb usb3-port5: status 0503, change 0004, 480 Mb/s
[27521.526528] usb 3-5: USB disconnect, device number 4
[27521.526736] usb 3-5: unregistering device
[27521.804029] usb 3-5: new high-speed USB device number 5 using xhci_hcd
[27527.076067] usb 3-5: device descriptor read/64, error -110
[27542.692027] usb 3-5: device descriptor read/64, error -110
[27542.916047] usb 3-5: new high-speed USB device number 6 using xhci_hcd
[27548.068043] usb 3-5: device descriptor read/64, error -110
[27563.684073] usb 3-5: device descriptor read/64, error -110
[27563.792133] usb usb3-port5: attempt power cycle
[27563.924381] hub 3-0:1.0: port_wait_reset: err = -11
[27563.925213] usb usb3-port5: not enabled, trying reset again...
[27564.184398] usb 3-5: new high-speed USB device number 7 using xhci_hcd
[27569.196322] xhci_hcd 0000:67:00.0: Timeout while waiting for setup device command
[27574.572040] xhci_hcd 0000:67:00.0: Timeout while waiting for setup device command
[27574.776053] usb 3-5: device not accepting address 7, error -62
[27574.900165] usb 3-5: new high-speed USB device number 8 using xhci_hcd
[27579.948039] xhci_hcd 0000:67:00.0: Timeout while waiting for setup device command
[27585.324331] xhci_hcd 0000:67:00.0: Timeout while waiting for setup device command
[27585.528040] usb 3-5: device not accepting address 8, error -62
[27585.528389] usb usb3-port5: unable to enumerate USB device
[27585.528424] hub 3-0:1.0: state 7 ports 5 chg 0000 evt 0020
To reproduce the issue, these conditions must be met:
- a noisy radio environment (cafe or office) to cause frequent remote
wakeup events
- no Bluetooth device is connected, so autosuspend is not prohibited
- the Bluetooth interface is opened, so remote wakeup is enabled when
the device runs into autosuspend
Then I can reproduce the issue within sereval hours each time.
Increasing TRSMRCY or setting USB_QUIRK_RESET doesn't help at all.
Since the remote wakeup capability is super broken, just disable it to
get rid of the troubles. The device can still be autosuspended when
the bluetooth interface is closed, which won't break the device as
remote wakeup is unneeded in this case.
Link: https://bbs.archlinux.org/viewtopic.php?id=308169
Link: https://bbs.bee-link.com/d/7694-gtr9-pro-ai-max-395-usb-issues
Signed-off-by: Rong Zhang <i@rong.moe>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add the vendor/product ID (0x37ad, 0x0600) to usb_device_id table
for Realtek 8761BUV.
The device info from /sys/kernel/debug/usb/devices as below.
T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 4 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=37ad ProdID=0600 Rev= 2.00
S: Manufacturer=
S: Product=TP-Link Bluetooth USB Adapter
S: SerialNumber=ACA7F14FD2A5
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
Signed-off-by: Nils Helmig <nils.helmig@web.de>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
non-serdev device
hu->serdev is NULL for hci_uart attached via non-serdev paths, but
qca_dmp_hdr() unconditionally dereferences hu->serdev->dev.driver->name,
causing a NULL pointer dereference.
Fix by guarding the dereference with a NULL check and falling back to
"hci_ldisc_qca" for the non-serdev case.
Fixes: 06d3fdfcdf5c ("Bluetooth: hci_qca: Add qcom devcoredump support")
Signed-off-by: Zijun Hu <zijun.hu@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
non-serdev device
hu->serdev is NULL for hci_uart attached via non-serdev paths, but
qca_setup() unconditionally calls serdev_device_get_drvdata(hu->serdev)
and dereferences the result, causing a NULL pointer dereference.
Fix by guarding the dereference with a NULL check, consistent with the
rest of qca_setup().
Fixes: 22d893eec0d5 ("Bluetooth: hci_qca: Refactor HFP hardware offload capability handling")
Signed-off-by: Zijun Hu <zijun.hu@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add USB ID 2c4e:0128 for Mercusys MA60XNB, an RTL8851BU-based
Wi-Fi + Bluetooth adapter.
The information in /sys/kernel/debug/usb/devices about the Bluetooth
device is listed as the below:
T: Bus=03 Lev=01 Prnt=01 Port=04 Cnt=01 Dev#= 3 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=2c4e ProdID=0128 Rev= 0.00
S: Manufacturer=Realtek
S: Product=802.11ax WLAN Adapter
S: SerialNumber=00e04c000001
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=500mA
A: FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 8 Cls=ff(vend.) Sub=ff Prot=ff Driver=rtw89_8851bu
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=07(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=09(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=0a(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=0b(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=0c(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Cc: stable@vger.kernel.org # 6.6.x
Signed-off-by: Zenm Chen <zenmchen@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
In btmtk_setup_firmware_79xx, the data length indicated by wmt_params.dlen
in the cmd buffer is MTK_SEC_MAP_NEED_SEND_SIZE + 1. Except for the first
byte, the remaining length is MTK_SEC_MAP_NEED_SEND_SIZE. memcpy copied one
more byte to cmd + 1 than the remaining length. Align the length passed to
memcpy to avoid exceeding current section map.
Signed-off-by: Jiajia Liu <liujiajia@kylinos.cn>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Device from /sys/kernel/debug/usb/devices:
T: Bus=09 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=8087 ProdID=0040 Rev= 0.00
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=1ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms
Signed-off-by: Ravindra <ravindra@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add VID 13d3 & PID 3609 for MediaTek MT7925 USB Bluetooth chip.
The information in /sys/kernel/debug/usb/devices about the Bluetooth
device is listed as the below.
T: Bus=06 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=13d3 ProdID=3609 Rev= 1.00
S: Manufacturer=MediaTek Inc.
S: Product=Wireless_Device
S: SerialNumber=000000000
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA
A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms
I: If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us
I:* If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us
Signed-off-by: luke-yj.chen <luke-yj.chen@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
PCMCIA is almost completely obsolete (the last computers supporting it
natively were from ~2009), and the general consensus [1] seems to be
that support for it should be gradually removed from the kernel.
In 2023, an initial step of removing all the PCMCIA char drivers was
taken in commit 9b12f050c76f ("char: pcmcia: remove all the drivers"),
and that has not been reverted, so it seems logical to continue this
process by removing more low-hanging fruit.
These three Bluetooth drivers have had no meaningful changes since
their status was discussed in 2022 [2], and are unlikely to have any
remaining users. The latest functional change to any of them was a
patch to bluecard_cs to fix LED blinking behavior in 2017. The other
two drivers have not had any meaningful changes made since 2007. Remove
them.
Note that even with these drivers removed, it is still possible to use
other PCMCIA Bluetooth cards that present themselves as a standard
serial port via serial_cs and hciattach while the serial_cs driver is
still present.
[1] https://lore.kernel.org/all/c5b39544-a4fb-4796-a046-0b9be9853787@app.fastmail.com/
[2] https://lore.kernel.org/all/Y07d7rMvd5++85BJ@owl.dominikbrodowski.net/
Signed-off-by: Ethan Nelson-Moore <enelsonmoore@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
RTL8761B and RTL8761BU devices report HCI version 5.1 but do not
support the LE Extended Scan commands. This causes repeated failures
with Opcode 0x2042 (LE Set Extended Scan Parameters) returning -EBUSY
when BlueZ attempts extended scanning while a connection is active.
Set HCI_QUIRK_BROKEN_EXT_SCAN for CHIP_ID_8761B to make BlueZ fall
back to legacy LE scan commands which the firmware supports correctly.
Tested with RTL8761BU (USB ID 0bda:a728) where the issue manifested
as continuous 'Opcode 0x2042 failed: -16' errors in dmesg whenever
a BLE connection was active.
Signed-off-by: Alexej Sidorenko <alexej@sidorenko.cz>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add the vendor/product ID (0x0bda, 0xd923) to usb_device_id table for
Realtek RTL8922AE.
The device info from /sys/kernel/debug/usb/devices as below.
T: Bus=10 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0bda ProdID=d923 Rev= 0.00
S: Manufacturer=Realtek
S: Product=Bluetooth Radio
S: SerialNumber=00E04C885A01
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms
Signed-off-by: Chen Zhang <zhangchen01@kylinos.cn>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add the vendor/product ID (0x0bda, 0xd922) to usb_device_id table for
Realtek RTL8922AE.
The device info from /sys/kernel/debug/usb/devices as below.
T: Bus=10 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0bda ProdID=d922 Rev= 0.00
S: Manufacturer=Realtek
S: Product=Bluetooth Radio
S: SerialNumber=00E04C885A01
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms
Signed-off-by: Chen Zhang <zhangchen01@kylinos.cn>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add the USB ID for the Mercusys MA530 Bluetooth adapter. The device uses
a Realtek RTL8761BUV controller and works with the existing Realtek setup
path.
The device reports vendor ID 0x2c4e and product ID 0x0115, and loads the
rtl_bt/rtl8761bu_fw.bin firmware successfully with this quirk.
Signed-off-by: Hrvoje Nuic <hrvoje.nuic@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add an event filter to filter event with specific opcode to prevent BT
stack from receiving unexpected event.
Event with opcode 0xfc5d is generated when MediaTek's Bluetooth enable
firmware logs and is not expected to be sent to userspace.
Signed-off-by: Chris Lu <chris.lu@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add VID 0e8d & PID 8c38 for MediaTek MT7925 USB Bluetooth chip.
The information in /sys/kernel/debug/usb/devices about the Bluetooth
device is listed as the below.
T: Bus=06 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0e8d ProdID=8c38 Rev= 1.00
S: Manufacturer=MediaTek Inc.
S: Product=Wireless_Device
S: SerialNumber=000000000
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA
A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms
I: If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us
I:* If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us
Signed-off-by: Chris Lu <chris.lu@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add VID 0e8d & PID 223c for MediaTek MT7922 USB Bluetooth chip.
The information in /sys/kernel/debug/usb/devices about the Bluetooth
device is listed as the below.
T: Bus=07 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0e8d ProdID=223c Rev= 1.00
S: Manufacturer=MediaTek Inc.
S: Product=Wireless_Device
S: SerialNumber=000000000
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA
A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms
I: If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us
I:* If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us
Signed-off-by: Chris Lu <chris.lu@mediatek.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
When driver encounters a TOP exception, ACPI methods will be called
for Product level reset since Wifi and BT share the same TOP. BT driver
will first reprobe the wifi driver and then reprobe BT.
Signed-off-by: Chandrashekar Devegowda <chandrashekar.devegowda@intel.com>
Signed-off-by: Venkat Rao Bagalkote <venkat88@linux.ibm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
When bt_en is pulled high by hardware, the host does not re-download
the firmware after SSR. The controller loads the rampatch and NVM
internally.
On HMT chip, the rampatch is ~264 KB and the NVM is ~9.4 KB. The
loading process takes approximately 70 ms. The previous 50 ms delay is
too short, causing the controller to not respond to the reset command
sent by the host, which leads to BT initialization failure:
Bluetooth: hci0: QCA memdump Done, received 458752, total 458752
Bluetooth: hci0: mem_dump_status: 2
Bluetooth: hci0: Opcode 0x0c03 failed: -110
Increase the delay to 100 ms, which was confirmed as a safe value by
the controller, to ensure the controller has finished loading the
firmware before the host sends commands.
Steps to reproduce:
1. Trigger SSR and wait for SSR to complete:
hcitool cmd 0x3f 0c 26
2. Run "bluetoothctl power on" and observe that BT fails to start.
Fixes: fce1a9244a0f ("Bluetooth: hci_qca: Fix SSR (SubSystem Restart) fail when BT_EN is pulled up by hw")
Cc: stable@vger.kernel.org
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Shuai Zhang <shuai.zhang@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
The Bluetooth host decides whether to download firmware by reading the
controller firmware download completion flag and firmware version
information.
If a USB error occurs during the firmware download process (for example
due to a USB disconnect), the download is aborted immediately. An
incomplete firmware transfer does not cause the controller to set the
download completion flag, but the firmware version information may be
updated at an early stage of the download process.
In this case, after USB reconnection, the host attempts to re-download
the firmware because the download completion flag is not set. However,
since the controller reports the same firmware version as the target
firmware, the download is skipped. This ultimately results in the
firmware not being properly updated on the controller.
This change removes the restriction that skips firmware download when
the versions are equal. It covers scenarios where the USB connection
can be disconnected at any time and ensures that firmware download can
be retriggered after USB reconnection, allowing the Bluetooth firmware
to be correctly and completely updated.
Fixes: 3267c884cefa ("Bluetooth: btusb: Add support for QCA ROME chipset family")
Cc: stable@vger.kernel.org
Signed-off-by: Shuai Zhang <shuai.zhang@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Vulnerabilities leading to Use-After-Free (UAF) and Null Pointer
Dereference (NPD) conditions were observed in the lifecycle management
of hci_uart.
The primary issue arises because the workqueues (init_ready and
write_work) are only flushed/cancelled if the HCI_UART_PROTO_READY
flag is set during TTY close. If a hangup occurs before setup completes,
hci_uart_tty_close() skips the teardown of these workqueues and
proceeds to free the `hu` struct. When the scheduled work executes
later, it blindly dereferences the freed `hu` struct.
Furthermore, several data races and UAFs were identified in the teardown
sequence:
1. Calling hci_uart_flush() from hci_uart_close() without effectively
disabling write_work causes a race condition where both can concurrently
double-free hu->tx_skb. This happens because protocol timers can
concurrently invoke hci_uart_tx_wakeup() and requeue write_work.
2. Calling hci_free_dev(hdev) before hu->proto->close(hu) causes a UAF
when vendor specific protocol close callbacks dereference hu->hdev.
3. In the initialization error paths, failing to take the proto_lock
write lock before clearing PROTO_READY leads to races with active
readers. Additionally, hci_uart_tty_receive() accesses hu->hdev
outside the read lock, leading to UAFs if the initialization error
path frees hdev concurrently.
Fix these synchronization and lifecycle issues by:
1. Re-ordering hci_uart_tty_close() to clear HCI_UART_PROTO_READY first,
followed immediately by a cancel_work_sync(&hu->write_work). Clearing
the flag locks out concurrent protocol timers from successfully invoking
hci_uart_tx_wakeup(), effectively rendering the cancellation permanent
and preventing the tx_skb double-free.
2. Note: Clearing PROTO_READY early causes hci_uart_close() to skip
hu->proto->flush(). This is perfectly safe in the tty_close path
because hu->proto->close() executes shortly after, which intrinsically
purges all protocol SKB queues and tears down the state.
3. Relocating hu->proto->close(hu) strictly prior to hci_free_dev(hdev)
across all close and error paths to prevent vendor-level UAFs.
4. Moving the hdev->stat.byte_rx increment in hci_uart_tty_receive()
inside the proto_lock read-side critical section to safely synchronize
with device unregistration.
5. Adding cancel_work_sync(&hu->write_work) to hci_uart_close() to safely
flush the workqueue before hci_uart_flush() is invoked via the HCI core.
6. Utilizing cancel_work_sync() instead of disable_work_sync() across
all paths to prevent permanently breaking user-space retry capabilities.
Fixes: 3b799254cf6f ("Bluetooth: hci_uart: Cancel init work before unregistering")
Cc: stable@vger.kernel.org
Signed-off-by: Mingyu Wang <25181214217@stu.xidian.edu.cn>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
The setup_packet of control urb is not freed if usb_submit_urb fails or
the submitted urb is killed. Add free in these two paths.
Fixes: a1c49c434e150 ("Bluetooth: btusb: Add protocol support for MediaTek MT7668U USB devices")
Signed-off-by: Jiajia Liu <liujiajia@kylinos.cn>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
btintel_pcie_get_mac_access() and btintel_pcie_release_mac_access()
were programming STOP_MAC_ACCESS_DIS and XTAL_CLK_REQ in addition to
the MAC_ACCESS_REQ handshake. These bits are not part of the host
MAC-access handshake on the supported parts; the driver was
programming them incorrectly. Drop the writes so the register update
contains only the bits the controller actually consumes.
Fixes: b9465e6670a2 ("Bluetooth: btintel_pcie: Read hardware exception data")
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Since the timer uses jiffies as its unit rather than ms, the timeout value
must be converted from ms to jiffies when configuring the timer. Otherwise,
the intended 8s timeout is incorrectly set to approximately 33s.
To improve readability, embed msecs_to_jiffies() directly in the macro
definitions and drop the _MS suffix from macros that now yield jiffies
values: MEMDUMP_TIMEOUT, FW_DOWNLOAD_TIMEOUT, IBS_DISABLE_SSR_TIMEOUT,
CMD_TRANS_TIMEOUT, and IBS_BTSOC_TX_IDLE_TIMEOUT.
IBS_WAKE_RETRANS_TIMEOUT_MS and IBS_HOST_TX_IDLE_TIMEOUT_MS are
intentionally left unchanged. Their values are stored in the struct fields
wake_retrans and tx_idle_delay, which hold ms values at runtime and can be
modified via debugfs. The msecs_to_jiffies() conversion happens at each
call site against the field value, so it cannot be embedded in the macro.
Wake timer depends on commit c347ca17d62a
Cc: stable@vger.kernel.org
Fixes: d841502c79e3 ("Bluetooth: hci_qca: Collect controller memory dump during SSR")
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Shuai Zhang <shuai.zhang@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
MT7925 (USB ID 0e8d:e025) on fw version 20260106153314 sends WMT
FUNC_CTRL events that are missing the status field.
Prior to commit 006b9943b982 ("Bluetooth: btmtk: validate WMT event SKB
length before struct access") the status was read from out-of-bounds of
SKB data, which usually would result to success with
BTMTK_WMT_ON_UNDONE, although I don't know the intent here. The bounds
check added in that commit returns with error instead, producing
"Bluetooth: hci0: Failed to send wmt func ctrl (-22)" and makes the
device unusable.
Fix the regression by interpreting too short packet as status
BTMTK_WMT_ON_UNDONE, which makes the device work normally again.
Fixes: 634a4408c061 ("Bluetooth: btmtk: validate WMT event SKB length before struct access")
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Tested-by: Mikhail Gavrilov <mikhail.v.gavrilov@gmail.com> # MT7922 (0489:e0e2)
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
virtbt_rx_handle() reads the leading pkt_type byte from the RX skb
and forwards the remainder to hci_recv_frame() for every
event/ACL/SCO/ISO type, without checking that the remaining payload
is at least the fixed HCI header for that type.
After the preceding patch bounds the backend-supplied used.len to
[1, VIRTBT_RX_BUF_SIZE], a one-byte completion still reaches
hci_recv_frame() with skb->len already pulled to 0. If the byte
happened to be HCI_ACLDATA_PKT, the ACL-vs-ISO classification
fast-path in hci_dev_classify_pkt_type() dereferences
hci_acl_hdr(skb)->handle whenever the HCI device has an active
CIS_LINK, BIS_LINK, or PA_LINK connection, reading two bytes of
uninitialized RX-buffer data. The same hazard exists for every
packet type the driver accepts because none of the switch cases in
virtbt_rx_handle() check skb->len against the per-type minimum HCI
header size before handing the frame to the core.
After stripping pkt_type, require skb->len to cover the fixed
header size for the selected type (event 2, ACL 4, SCO 3, ISO 4)
before calling hci_recv_frame(); drop ratelimited otherwise.
Unknown pkt_type values still take the original kfree_skb() default
path.
Use bt_dev_err_ratelimited() because both the length and pkt_type
values come from an untrusted backend that can otherwise flood the
kernel log.
Fixes: 160fbcf3bfb9 ("Bluetooth: virtio_bt: Use skb_put to set length")
Cc: stable@vger.kernel.org
Cc: Soenke Huster <soenke.huster@eknoes.de>
Signed-off-by: Michael Bommarito <michael.bommarito@gmail.com>
Assisted-by: Claude:claude-opus-4-7
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
virtbt_rx_work() calls skb_put(skb, len) where len comes directly
from virtqueue_get_buf() with no validation against the buffer we
posted to the device. The RX skb is allocated in virtbt_add_inbuf()
and exposed to virtio as exactly 1000 bytes via sg_init_one().
Checking len against skb_tailroom(skb) is not sufficient because
alloc_skb() can leave more tailroom than the 1000 bytes actually
handed to the device. A malicious or buggy backend can therefore
report used.len between 1001 and skb_tailroom(skb), causing skb_put()
to include uninitialized kernel heap bytes that were never written by
the device.
The same path also accepts len == 0, in which case skb_put(skb, 0)
leaves the skb empty but virtbt_rx_handle() still reads the pkt_type
byte from skb->data, consuming uninitialized memory.
Define VIRTBT_RX_BUF_SIZE once and reuse it in alloc_skb() and
sg_init_one(), and gate virtbt_rx_work() on that same constant so
the bound checked matches the buffer actually exposed to the device.
Reject used.len == 0 in the same gate so an empty completion can
no longer reach virtbt_rx_handle().
Use bt_dev_err_ratelimited() because the length value comes from an
untrusted backend that can otherwise flood the kernel log.
Same class of bug as commit c04db81cd028 ("net/9p: Fix buffer
overflow in USB transport layer"), which hardened the USB 9p
transport against unchecked device-reported length.
Fixes: 160fbcf3bfb9 ("Bluetooth: virtio_bt: Use skb_put to set length")
Cc: stable@vger.kernel.org
Cc: Soenke Huster <soenke.huster@eknoes.de>
Signed-off-by: Michael Bommarito <michael.bommarito@gmail.com>
Assisted-by: Claude:claude-opus-4-7
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
btmtk_usb_hci_wmt_sync() casts the WMT event response SKB data to
struct btmtk_hci_wmt_evt (7 bytes) and struct btmtk_hci_wmt_evt_funcc
(9 bytes) without first checking that the SKB contains enough data.
A short firmware response causes out-of-bounds reads from SKB tailroom.
Use skb_pull_data() to validate and advance past the base WMT event
header. For the FUNC_CTRL case, pull the additional status field bytes
before accessing them.
Fixes: d019930b0049 ("Bluetooth: btmtk: move btusb_mtk_hci_wmt_sync to btmtk.c")
Cc: stable@vger.kernel.org
Signed-off-by: Tristan Madani <tristan@talencesecurity.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
When a fault is injected during hci_uart line discipline setup, the
proto open() callback may fail leaving hu->priv as NULL. A subsequent
TIOCSTI ioctl can trigger the recv() callback before priv is
initialized, causing a NULL pointer dereference.
Fix all four affected HCI UART protocol drivers by adding a NULL check
on hu->priv at the start of their recv() callbacks: h4, h5, ath and
bcsp.
Reported-by: syzbot+ff30eeab8e07b37d524e@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=ff30eeab8e07b37d524e
Signed-off-by: Aurelien DESBRIERES <aurelien@hackers.camp>
Assisted-by: Claude:claude-sonnet-4-6
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
CSR boot stage register bit 12 is documented as a device warning,
not a fatal error. Rename the bit definition accordingly and stop
including it in btintel_pcie_in_error().
This keeps warning-only boot stage values from being classified as
errors while preserving abort-handler state as the actual error
condition.
Fixes: 190377500fde ("Bluetooth: btintel_pcie: Dump debug registers on error")
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Sai Teja Aluvala <aluvala.sai.teja@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
When a Bluetooth controller encounters a coredump, it triggers the
Subsystem Restart (SSR) mechanism. The controller first reports the
coredump data and, once the upload is complete, sends a hw_error
event. The host relies on this event to proceed with subsequent
recovery actions.
If the host has not finished processing the coredump data when the
hw_error event is received, it waits until either the processing is
complete or the 8-second timeout expires before handling the event.
The current implementation clears QCA_MEMDUMP_COLLECTION using
clear_bit(), which does not wake up waiters sleeping in
wait_on_bit_timeout(). As a result, the waiting thread may remain
blocked until the timeout expires even if the coredump collection
has already completed.
Fix this by clearing QCA_MEMDUMP_COLLECTION with
clear_and_wake_up_bit(), which also wakes up the waiting thread and
allows the hw_error handling to proceed immediately.
Test case:
- Trigger a controller coredump using:
hcitool cmd 0x3f 0c 26
- Tested on QCA6390.
- Capture HCI logs using btmon.
- Verify that the delay between receiving the hw_error event and
initiating the power-off sequence is reduced compared to the
timeout-based behavior.
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Shuai Zhang <shuai.zhang@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Use strscpy() instead of snprintf() to copy plain strings with no format
specifiers.
Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Align each descriptor/index/context region to 128 bytes before
calculating the total DMA pool size. This ensures the memory layout
shared with firmware meets the 128-byte alignment requirement.
The DMA pool alignment is also set to 128 bytes to match the firmware
expectation for all shared structures.
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
TI WL183x controllers advertise support for the HCI Enhanced Setup
Synchronous Connection command, but SCO setup fails when the enhanced
path is used. The only working configuration is to fall back to the
legacy HCI Setup Synchronous Connection (0x0028).
This matches the scenario described in commit 05abad857277
("Bluetooth: HCI: Add HCI_QUIRK_BROKEN_ENHANCED_SETUP_SYNC_CONN quirk").
Enable HCI_QUIRK_BROKEN_ENHANCED_SETUP_SYNC_CONN automatically for
devices compatible with:
- ti,wl1831-st
- ti,wl1835-st
- ti,wl1837-st
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add VID 0489 & PID e11d for MediaTek MT7922 USB Bluetooth chip.
Found in Dynabook GA/ZY (W6GAZY5RCL).
The information in /sys/kernel/debug/usb/devices about the Bluetooth
device is listed as the below.
T: Bus=03 Lev=01 Prnt=01 Port=03 Cnt=02 Dev#= 3 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0489 ProdID=e11d Rev= 1.00
S: Manufacturer=MediaTek Inc.
S: Product=Wireless_Device
S: SerialNumber=000000000
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Kamiyama Chiaki <nercone@nercone.dev>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
When USB support is disabled, the array is not referenced anywhere,
causing a warning:
drivers/bluetooth/btmtk.c:35:3: error: 'btmtk_mt6639_devs' defined but not used [-Werror=unused-const-variable=]
35 | } btmtk_mt6639_devs[] = {
| ^~~~~~~~~~~~~~~~~
Move it into the #ifdef block.
Fixes: 28b7c5a6db74 ("Bluetooth: btmtk: Add MT6639 (MT7927) Bluetooth support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add USB device ID 13d3:3588 (IMC Networks/Azurewave) for the MediaTek
MT7927 (Filogic 380) Bluetooth interface found on the ASUS ROG STRIX
X870E-E GAMING WIFI and ASUS ProArt X870E-Creator WiFi motherboards.
The information in /sys/kernel/debug/usb/devices about the Bluetooth
device is listed as the below.
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 5 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=13d3 ProdID=3588 Rev= 1.00
S: Manufacturer=MediaTek Inc.
S: Product=Wireless_Device
S: SerialNumber=000000000
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA
A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us
Link: https://bugzilla.kernel.org/show_bug.cgi?id=221096
Link: https://github.com/openwrt/mt76/issues/927
Signed-off-by: Javier Tia <floss@jetm.me>
Tested-by: Jose Tiburcio Ribeiro Netto <jnetto@mineiro.io>
Tested-by: Ivan Lubnin <lubnin.ivan@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add USB device ID 0489:e116 (Foxconn/Hon Hai) for the MediaTek MT7927
(Filogic 380) Bluetooth interface found on the TP-Link Archer TBE550E
PCIe adapter.
The information in /sys/kernel/debug/usb/devices about the Bluetooth
device is listed as the below.
T: Bus=01 Lev=01 Prnt=01 Port=05 Cnt=04 Dev#= 5 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0489 ProdID=e116 Rev= 1.00
S: Manufacturer=MediaTek Inc.
S: Product=Wireless_Device
S: SerialNumber=000000000
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA
A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
...
I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us
Link: https://bugzilla.kernel.org/show_bug.cgi?id=221096
Link: https://github.com/openwrt/mt76/issues/927
Signed-off-by: Javier Tia <floss@jetm.me>
Tested-by: Thibaut FRANCOIS <tibo@humeurlibre.fr>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add USB device ID 0489:e110 (Foxconn/Hon Hai) for the MediaTek MT7927
(Filogic 380) Bluetooth interface found on the MSI X870E Ace Max
motherboard.
The information in /sys/kernel/debug/usb/devices about the Bluetooth
device is listed as the below.
T: Bus=01 Lev=01 Prnt=01 Port=05 Cnt=04 Dev#= 5 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0489 ProdID=e110 Rev= 1.00
S: Manufacturer=MediaTek Inc.
S: Product=Wireless_Device
S: SerialNumber=000000000
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA
A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
...
I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us
Link: https://bugzilla.kernel.org/show_bug.cgi?id=221096
Link: https://github.com/openwrt/mt76/issues/927
Signed-off-by: Javier Tia <floss@jetm.me>
Tested-by: Nitin Gurram <nitin.reddy88@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add USB device ID 0489:e10f (Foxconn/Hon Hai) for the MediaTek MT7927
(Filogic 380) Bluetooth interface found on the Gigabyte Z790 AORUS
MASTER X motherboard.
The information in /sys/kernel/debug/usb/devices about the Bluetooth
device is listed as the below.
T: Bus=01 Lev=01 Prnt=01 Port=05 Cnt=04 Dev#= 5 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0489 ProdID=e10f Rev= 1.00
S: Manufacturer=MediaTek Inc.
S: Product=Wireless_Device
S: SerialNumber=000000000
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA
A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
...
I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us
Link: https://bugzilla.kernel.org/show_bug.cgi?id=221096
Link: https://github.com/openwrt/mt76/issues/927
Signed-off-by: Javier Tia <floss@jetm.me>
Tested-by: Chapuis Dario <chapuisdario4@gmail.com>
Tested-by: Evgeny Kapusta <3193631@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add USB device ID 0489:e0fa (Foxconn/Hon Hai) for the MediaTek MT7927
(Filogic 380) Bluetooth interface found on the Lenovo Legion Pro 7
16ARX9 laptop.
The information in /sys/kernel/debug/usb/devices about the Bluetooth
device is listed as the below.
T: Bus=01 Lev=01 Prnt=01 Port=05 Cnt=04 Dev#= 5 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0489 ProdID=e0fa Rev= 1.00
S: Manufacturer=MediaTek Inc.
S: Product=Wireless_Device
S: SerialNumber=000000000
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA
A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
...
I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us
Link: https://bugzilla.kernel.org/show_bug.cgi?id=221096
Link: https://github.com/openwrt/mt76/issues/927
Signed-off-by: Javier Tia <floss@jetm.me>
Tested-by: Llewellyn Curran <melinko2003@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add USB device ID 0489:e13a (Foxconn/Hon Hai) for the MediaTek MT7927
(Filogic 380) Bluetooth interface found on the ASUS ROG Crosshair X870E
Hero WiFi motherboard.
The information in /sys/kernel/debug/usb/devices about the Bluetooth
device is listed as the below.
T: Bus=01 Lev=01 Prnt=01 Port=05 Cnt=04 Dev#= 5 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0489 ProdID=e13a Rev= 1.00
S: Manufacturer=MediaTek Inc.
S: Product=Wireless_Device
S: SerialNumber=000000000
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA
A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
...
I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us
Link: https://bugzilla.kernel.org/show_bug.cgi?id=221096
Link: https://github.com/openwrt/mt76/issues/927
Signed-off-by: Javier Tia <floss@jetm.me>
Tested-by: Jose Tiburcio Ribeiro Netto <jnetto@mineiro.io>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Some MT6639 Bluetooth USB interfaces (e.g. IMC Networks 13d3:3588 on
ASUS ROG STRIX X870E-E and ProArt X870E-Creator boards) expose only a
single alternate setting (alt 0) on the ISO interface. The driver
unconditionally requests alt setting 1, which fails with EINVAL on
these devices, causing a ~20 second initialization delay and no LE
audio support.
Check the number of available alternate settings before selecting one.
If only alt 0 exists, use it; otherwise request alt 1 as before.
Closes: https://github.com/jetm/mediatek-mt7927-dkms/pull/39
Signed-off-by: Javier Tia <floss@jetm.me>
Reported-by: Ryan Gilbert <xelnaga@gmail.com>
Tested-by: Ryan Gilbert <xelnaga@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
The MediaTek MT7927 (Filogic 380) combo WiFi 7 + BT 5.4 module uses
hardware variant 0x6639 for its Bluetooth subsystem. Without this patch,
the chip fails with "Unsupported hardware variant (00006639)" or hangs
during firmware download.
Three changes are needed to support MT6639:
1. CHIPID workaround: On some boards the BT USB MMIO register reads
0x0000 for dev_id, causing the driver to skip the 0x6639 init path.
Force dev_id to 0x6639 only when the USB VID/PID matches a known
MT6639 device, avoiding misdetection if a future chip also reads
zero. This follows the WiFi-side pattern that uses PCI device IDs
to scope the same workaround.
2. Firmware naming: MT6639 uses firmware version prefix "2_1" instead of
"1_1" used by MT7925 and other variants. The firmware path is
mediatek/mt7927/BT_RAM_CODE_MT6639_2_1_hdr.bin, using the mt7927
directory to match the WiFi firmware convention. The filename will
likely change to use MT7927 once MediaTek submits a dedicated
Linux firmware binary.
3. Section filtering: The MT6639 firmware binary contains 9 sections, but
only sections with (dlmodecrctype & 0xff) == 0x01 are Bluetooth-related.
Sending the remaining WiFi/other sections causes an irreversible BT
subsystem hang requiring a full power cycle. This matches the Windows
driver behavior observed via USB captures.
Also add 0x6639 to the reset register (CONNV3) and firmware setup switch
cases alongside the existing 0x7925 handling.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=221096
Link: https://github.com/openwrt/mt76/issues/927
Reported-by: Ryan Gilbert <xelnaga@gmail.com>
Signed-off-by: Javier Tia <floss@jetm.me>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Use the common USB helper for looking up bulk and interrupt endpoints
instead of open coding.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Use the common USB helper for looking up bulk and interrupt endpoints
instead of open coding.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
When hci_register_dev() fails in hci_uart_register_dev()
HCI_UART_PROTO_INIT is not cleared before calling hu->proto->close(hu)
and setting hu->hdev to NULL. This means incoming UART data will reach
the protocol-specific recv handler in hci_uart_tty_receive() after
resources are freed.
Clear HCI_UART_PROTO_INIT with a write lock before calling
hu->proto->close() and setting hu->hdev to NULL. The write lock ensures
all active readers have completed and no new reader can enter the
protocol recv path before resources are freed.
This allows the protocol-specific recv functions to remove the
"HCI_UART_REGISTERED" guard without risking a null pointer dereference
if hci_register_dev() fails.
Fixes: 5df5dafc171b ("Bluetooth: hci_uart: Fix another race during initialization")
Signed-off-by: Jonathan Rissanen <jonathan.rissanen@axis.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
On platforms using an M.2 slot with both UART and USB support, bt_en is
pulled high by hardware. In this case, software-based power control
should be disabled. The current platforms are Lemans-EVK and Monaco-EVK.
Add QCA_WCN7850 to the existing condition so that power_ctrl_enabled is
cleared when bt_en is not software-controlled (or absent), aligning its
behavior with WCN6750 and WCN6855
Signed-off-by: Shuai Zhang <shuai.zhang@oss.qualcomm.com>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
