| Age | Commit message (Collapse) | Author |
|---|
|
Provide the real DV timings limits in VIDIOC_DV_TIMINGS_CAP. For the
outputs the pixelclock is limited by the CMT table <25000kHz, 2*94642kHz>,
for the inputs a slightly broader range is possible. The minimal
supported/tested resolution is 64px.
Signed-off-by: Martin Tůma <martin.tuma@digiteqautomotive.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
|
|
If a sub-device does not set enable_streams() and disable_streams() pad
ops while it sets the s_stream() video op to
v4l2_subdev_s_stream_helper(), enabling or disabling streaming either way
on the sub-device will result calling v4l2_subdev_s_stream_helper() and
v4l2_subdev_{enable,disable}_streams() recursively, exhausting the stack.
Return -ENOIOCTLCMD in this case to handle the situation gracefully.
Fixes: b62949ddaa52 ("media: subdev: Support single-stream case in v4l2_subdev_enable/disable_streams()")
Cc: stable@vger.kernel.org
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
|
|
Use the common USB helpers for looking up bulk and interrupt endpoints
(and determining max packet size) instead of open coding.
Note that the device has two bulk endpoints so there is no functional
change here.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Sean Young <sean@mess.org>
|
|
Use the common USB helper for looking up interrupt-in endpoints instead
of open coding.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Sean Young <sean@mess.org>
|
|
This is a Sonix SN8P2202XG microcontroller with firmware compatible with
the already supported Northstar 04eb:e004, implementing an MCE IR receiver
(PCB seems to be tracked for a transmitter too but missing related parts).
Found in a Skintek SK-CR-IN+IR ( http://www.skintek.it/SK-CR-IN+IR.php )
internal 3.5 inch USB card reader and MCE receiver combo
(implemented by, and wired as, separate USB devices)
PCB marking: AU6475 966816 STIR REV:A02 MCE
Signed-off-by: Riccardo Boninsegna <rboninsegna2@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
|
|
The YUV24 format is missing an entry in the v4l2_format_info().
The YUV24 format is the packed YUV 4:4:4 formats with 8 bits
per component.
Fixes: 0376a51fbe5e ("media: v4l: Add packed YUV444 24bpp pixel format")
Signed-off-by: Nas Chung <nas.chung@chipsnmedia.com>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
|
|
The function hantro_run() is declared but never defined nor used, remove
the dangling declaration.
Signed-off-by: Rouven Czerwinski <rouven.czerwinski@linaro.org>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
|
|
handle_dynamic_resolution change requires that the state_lock be acquired
based on the lockdep_assert_held. However, the
handle_dynamic_resolution_change call in initialize_sequence does not
properly obtain the lock before calling.
Since the v4l2_ctrl_find and s_ctrl can sleep, they should not be called
while a lock is already held. Store off the fbc_buf_count then properly
update control once lock has been freed.
Signed-off-by: Brandon Brnich <b-brnich@ti.com>
Tested-by: Jackson Lee <jackson.lee@chipsnmedia.com>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
|
|
Possible use after free if IRQ thread manages to obtain spinlock between
m2m_ctx release and wave5_release function removing stream instance from
list of active instances. The IRQ thread looks for the m2m_ctx which is
freed so null pointer dereference occurs.
Signed-off-by: Brandon Brnich <b-brnich@ti.com>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Tested-by: Jackson Lee <jackson.lee@chipsnmedia.com>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
|
|
The VDPU383 support for hevc and h264 use structs with bitfields to
represent the SPS and PPS.
Because the fields are mostly unaligned and numerous, it brings compiler
issues, especially with clang.
To prevent that, switch to using the global bitwriter previously
introduced instead.
Signed-off-by: Detlev Casanova <detlev.casanova@collabora.com>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
|
|
Currently, the common code files for hevc and h264 use structs with
bitfields to represent the HW RPS buffer.
Because the bitfields are mostly unaligned and numerous, it brings compiler
issues, especially with clang.
To prevent that, switch to using the global bitwriter previously
introduced instead.
Signed-off-by: Detlev Casanova <detlev.casanova@collabora.com>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
|
|
Both rkvdec-h264.c and rkvdec-hevc.c use their own bitwriter
function and macros.
Move to using the global one introduced before.
Signed-off-by: Detlev Casanova <detlev.casanova@collabora.com>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
|
|
The use of structures with bitfields is good when the values are
somewhat aligned.
More mis-alignement means that compilers need to do more gymnastics
to edit the fields values.
Some cases have been reported with CLang on specific architectures
like armhf and hexagon, where the compiler would allocate a bigger
local stack than needed or even completely freeze during compilation.
Some fixes have been provided to ease the issues, but the real fix
here is to use a bitwriter instead of heavily unaligned bitfields.
This is a preparation commit to provide a global bitwriter interface
for the whole driver.
Signed-off-by: Detlev Casanova <detlev.casanova@collabora.com>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
|
|
Some pixel formats can only be produced if the decoder outputs
reference pictures directly. In some cases, such as AV1 film-grain,
the use of the post-processor is strictly required. In this case,
only enumerate the post-processor supported formats. The exception is
when V4L2_FMTDESC_FLAG_ENUM_ALL is set, in this case, we enumerate
everything regardless of the state.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Fixes: bcd4f091cf1e ("media: verisilicon: Use V4L2_FMTDESC_FLAG_ENUM_ALL flag")
Cc: stable@vger.kernel.org
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
|
|
Wave5 encoder is capable of reading in numerous raw pixel formats.
Expose these formats and properly configure encoder if selected.
Signed-off-by: Jackson Lee <jackson.lee@chipsnmedia.com>
Signed-off-by: Nas Chung <nas.chung@chipsnmedia.com>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Tested-by: Brandon Brnich <b-brnich@ti.com>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
|
|
Constrained Baseline Profile (CBP) and Baseline Profile (BP) have been
treated as the same.
Introduce the ability to differentiate between the two.
Fixes: 9707a6254a8a ("media: chips-media: wave5: Add the v4l2 layer")
Cc: stable@vger.kernel.org
Signed-off-by: Jackson Lee <jackson.lee@chipsnmedia.com>
Signed-off-by: Nas Chung <nas.chung@chipsnmedia.com>
Tested-by: Brandon Brnich <b-brnich@ti.com>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
|
|
Implement V4L2_CID_MPEG_VIDEO_BACKGROUND_DETECTION in the Wave5 encoder
driver. When enabled, the hardware detects background regions in a frame
and uses fewer bits or skip mode to encode them, reducing bitrate for
streams with stationary scenes.
Signed-off-by: Jackson Lee <jackson.lee@chipsnmedia.com>
Signed-off-by: Nas Chung <nas.chung@chipsnmedia.com>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
|
|
Add a generic V4L2 boolean control V4L2_CID_MPEG_VIDEO_BACKGROUND_DETECTION
that allows encoders to detect background regions in a frame and use fewer
bits or skip mode to encode them, potentially reducing bitrate for streams
with stationary scenes.
Signed-off-by: Jackson Lee <jackson.lee@chipsnmedia.com>
Signed-off-by: Nas Chung <nas.chung@chipsnmedia.com>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
|
|
During encoder processing, there is a case where the IRQ response could
return the buffer back to userspace via v4l2_m2m_buf_done call. In this
time, userspace could queue up this same buffer before start_encode removes
the index from the ready queue. This would then lead to a case where the
buffer in the ready queue could be a self loop due to the
WRITE_ONCE(prev->next, new) call in __list_add.
When __list_del is finally called, the loop is already made so nothing
points back to ready queue list head and pointers are poisoned.
A buffer should not be marked as DONE before the buffer is removed from
m2m ready queue. Move removal entirely to finish_encode.
Fixes: 9707a6254a8a6 ("media: chips-media: wave5: Add the v4l2 layer")
Cc: stable@vger.kernel.org
Signed-off-by: Brandon Brnich <b-brnich@ti.com>
Tested-by: Jackson Lee <jackson.lee@chipsnmedia.com>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
|
|
Since a recent fix the mtk_jpeg_release function cancels any pending
or running work present in the driver workqueue using
cancel_work_sync function.
Currently, only the multicore based variants use this workqueue and they
have the jpeg_worker platform data field initialized with a workqueue
callback function. For the others, this field value remain NULL by
default.
The cancel_work_sync function is unconditionally called in
mtk_jpeg_release function, even for the variants that do not use the
workqueue. This call generates a WARN_ON print in __flush_work because
the workqueue callback function presence check fails in __flush_work
function (used by cancel_work_sync).
So, to avoid these warnings, call cancel_work_sync only if a workqueue
callback is defined in platform data.
Fixes: 34c519feef3e ("media: mtk-jpeg: fix use-after-free in release path due to uncancelled work")
Cc: stable@vger.kernel.org
Signed-off-by: Louis-Alexis Eyraud <louisalexis.eyraud@collabora.com>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
|
|
HEVC slice parameters are shared stateless V4L2 controls, but the common
validation path does not verify the active L0/L1 reference counts before
driver-specific code consumes them.
The original report came from Cedrus, but the active count bounds are
not Cedrus-specific. Validate them in the common HEVC slice control path
so stateless HEVC drivers get the same basic guarantees as soon as the
control is queued.
Do not reject ref_idx_l0/ref_idx_l1 entries here. Existing userspace may
use out-of-range sentinel values such as 0xff for missing references, and
some hardware can use that information for concealment. Keep this common
check limited to the active reference counts.
Fixes: d395a78db9eab ("media: hevc: Add decode params control")
Cc: stable@vger.kernel.org
Signed-off-by: Pengpeng Hou <pengpeng@iscas.ac.cn>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
|
|
We have to report ENOMEM if no buffer is allocated.
Typo dropped a "!". Restore it.
Fixes: 50acaad3d202 ("media: rc: ttusbir: respect DMA coherency rules")
Cc: stable@vger.kernel.org
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
|
|
clang-22 warns about csiphy_match_clock_name() taking a variable format
string that is not checked against the 'int index' argument:
drivers/media/platform/qcom/camss/camss-csiphy.c:566:44: error: diagnostic behavior may be improved by
adding the 'format(printf, 2, 3)' attribute to the declaration of 'csiphy_match_clock_name'
[-Werror,-Wmissing-format-attribute]
561 | static bool csiphy_match_clock_name(const char *clock_name, const char *format,
| __attribute__((format(printf, 2, 3)))
562 | int index)
563 | {
564 | char name[16]; /* csiphyXXX_timer\0 */
565 |
566 | snprintf(name, sizeof(name), format, index);
| ^
drivers/media/platform/qcom/camss/camss-csiphy.c:561:13: note: 'csiphy_match_clock_name' declared here
561 | static bool csiphy_match_clock_name(const char *clock_name, const char *format,
| ^
Change the function to use a snprintf() style format string that allows this
to be checked at the call site.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
|
|
Add missing required clocks (cpas_ahb and camnoc_axi) for VFE lite
instances on sa8775p platform. These clocks are necessary for proper
VFE lite operation:
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Wenmeng Liu <wenmeng.liu@oss.qualcomm.com>
Fixes: e7b59e1d06fb ("media: qcom: camss: Add support for VFE 690")
Cc: stable@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
|
|
Fix the mismatch between clock list and clock rate table for CSID lite
instances. The current implementation has 5 clocks defined but only 2
are actually needed (vfe_lite_csid and vfe_lite_cphy_rx), while the
clock rate table doesn't match this configuration.
Update both clock list and rate table to maintain consistency:
- Remove unused clocks: cpas_vfe_lite, vfe_lite_ahb, vfe_lite
- Update clock rate table to match the remaining two clocks
Signed-off-by: Wenmeng Liu <wenmeng.liu@oss.qualcomm.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Fixes: ed03e99de0fa ("media: qcom: camss: Add support for CSID 690")
Cc: stable@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
|
|
Fix BUF_DONE_IRQ_STATUS_RDI_OFFSET calculation for csid lite on
sa8775p platform. The offset should be 0 for csid lite on sa8775p,
Signed-off-by: Wenmeng Liu <wenmeng.liu@oss.qualcomm.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Fixes: ed03e99de0fa ("media: qcom: camss: Add support for CSID 690")
Cc: stable@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
|
|
Follow the commit bfe1326573ff ("venus: Fix for H265 decoding failure.")
and increase H265D_MAX_SLICE following firmware requirements on that
platform. Otherwise decoding of the H.265 streams fails with the
"insufficient scratch_1 buffer size" from the firmware.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Dikshita Agarwal <dikshita.agarwal@oss.qualcomm.com>
Reviewed-by: Vikash Garodia <vikash.garodia@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
[bod: Fixed commit log withthe => with the]
Fixes: e1f5d32608ec ("media: iris: Add internal buffer calculation for HEVC and VP9 decoders")
Cc: stable@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
|
|
During concurrency testing, multiple instances can run in parallel, and
each instance uses its own inst->lock while the core->lock protects the
list of active instances. The race happens because these locks cover
different scopes, inst->lock protects only the internals of a single
instance, while the Macro Blocks Per Frame (MBPF) checker walks the
core list under core->lock and reads fields like fmt_src->width and
fmt_src->height. At the same time, iris_close() may free fmt_src and
fmt_dst under inst->lock while the instance is still present in the core
list. This allows a situation where the MBPF checker, still iterating
through the core list, reaches an instance whose fmt_src was already
freed by another thread and ends up dereferencing a dangling pointer,
resulting in a use-after-free. This happens because the MBPF checker
assumes that any instance in the core list is fully valid, but the
freeing of fmt_src and fmt_dst without removing the instance from the
core list is not correct.
The correct ordering is to defer freeing fmt_src and fmt_dst until after
the instance has been removed from the core list and all teardown under
the core lock has completed, ensuring that no dangling pointers are ever
exposed during MBPF checks.
Reviewed-by: Vikash Garodia <vikash.garodia@oss.qualcomm.com>
Signed-off-by: Vishnu Reddy <busanna.reddy@oss.qualcomm.com>
Reviewed-by: Dikshita Agarwal <dikshita.agarwal@oss.qualcomm.com>
Fixes: 5ad964ad5656 ("media: iris: Initialize and deinitialize encoder instance structure")
Cc: stable@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
|
|
Currently the driver switches the vcodec GDSC to hardware (HW) mode
before firmware load and boot sequence. GDSC can be powered off, keeping
in hw mode, thereby the vcodec registers programmed in TrustZone (TZ)
carry default (reset) values.
Move the transition to HW mode after firmware load and boot sequence.
The bug was exposed with driver configuring different stream ids to
different devices via iommu-map. With registers carrying reset values,
VPU would not generate desired stream-id, thereby leading to SMMU fault.
For vpu4, when GDSC is switched to HW mode, there is a need to perform
the reset operation. Without reset, there are occasional issues of
register corruption observed. Hence the vpu GDSC switch also involves
the reset.
Co-developed-by: Vishnu Reddy <busanna.reddy@oss.qualcomm.com>
Signed-off-by: Vishnu Reddy <busanna.reddy@oss.qualcomm.com>
Signed-off-by: Vikash Garodia <vikash.garodia@oss.qualcomm.com>
Reviewed-by: Dikshita Agarwal <dikshita.agarwal@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
[bod: occassional => occasional]
Fixes: dde659d37036 ("media: iris: Introduce vpu ops for vpu4 with necessary hooks")
Cc: stable@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
|
|
The core->iface_q_table_vaddr buffer is alloc'd with size queue_size
but freed with sizeof(*q_tbl_hdr) which is different.
Change the dma_free_attrs() size.
Signed-off-by: Thomas Fourier <fourier.thomas@gmail.com>
Reviewed-by: Dikshita Agarwal <dikshita.agarwal@oss.qualcomm.com>
Fixes: d7378f84e94e ("media: iris: introduce iris core state management with shared queues")
Cc: stable@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
|
|
The recent change in commit 1dabf00ee206 ("media: iris: gen1: Destroy
internal buffers after FW releases") introduced a regression where
session_release_buf() may free the buffer. The caller,
iris_release_internal_buffers(), continued to access `buffer` after the
call, leading to a potential use-after-free.
Fix this by setting BUF_ATTR_PENDING_RELEASE before calling
session_release_buf(), and reverting the flag if the call fails. This
ensures no dereference occurs after potential freeing.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Closes: https://lore.kernel.org/lkml/aYXvKAX3Pg3sL37P@stanley.mountain/#r
Signed-off-by: Dikshita Agarwal <dikshita.agarwal@oss.qualcomm.com>
Reviewed-by: Vikash Garodia <vikash.garodia@oss.qualcomm.com>
Fixes: 1dabf00ee206 ("media: iris: gen1: Destroy internal buffers after FW releases")
Cc: stable@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
|
|
When build-testined with CONFIG_QCOM_MDT_LOADER=m and VIDEO_QCOM_IRIS=y,
the kernel fails to link:
x86_64-linux-ld: drivers/media/platform/qcom/iris/iris_firmware.o: in function `iris_fw_load':
iris_firmware.c:(.text+0xb0): undefined reference to `qcom_mdt_get_size'
iris_firmware.c:(.text+0xfd): undefined reference to `qcom_mdt_load'
The problem is the conditional 'select' statement. Change this to
make the driver built-in here regardless of CONFIG_ARCH_QCOM.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dikshita Agarwal <dikshita.agarwal@oss.qualcomm.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Fixes: d19b163356b8 ("media: iris: implement video firmware load/unload")
Cc: stable@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
|
|
When build-testined with CONFIG_QCOM_MDT_LOADER=m and VIDEO_QCOM_VENUS=y,
the kernel fails to link:
x86_64-linux-ld: drivers/media/platform/qcom/venus/firmware.o: in function `venus_boot':
firmware.c:(.text+0x1e3): undefined reference to `qcom_mdt_get_size'
firmware.c:(.text+0x25a): undefined reference to `qcom_mdt_load'
firmware.c:(.text+0x272): undefined reference to `qcom_mdt_load_no_init'
The problem is the conditional 'select' statement. Change this to
make the driver built-in here regardless of CONFIG_ARCH_QCOM,
same as for the similar IRIS driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dikshita Agarwal <dikshita.agarwal@oss.qualcomm.com>
Fixes: 0399b696f7f4 ("media: venus: fix compile-test build on non-qcom ARM platform")
Cc: stable@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/remoteproc/linux
Pull rpmsg updates from Bjorn Andersson:
"Mark 'data' argument in rpmsg_send() const, and perculate to related
drivers. Replace deprecated class_destroy() with class_unregister()"
* tag 'rpmsg-v7.1' of git://git.kernel.org/pub/scm/linux/kernel/git/remoteproc/linux:
media: platform: mtk-mdp3: Constify buffer passed to mdp_vpu_sendmsg()
ASoC: qcom: Constify GPR packet being send over GPR interface
rpmsg: Constify buffer passed to send API
remoteproc: mtk_scp: Constify buffer passed to scp_send_ipi()
remoteproc: mtk_scp_ipi: Constify buffer passed to scp_ipi_send()
drivers: rpmsg: class_destroy() is deprecated
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- new CSI tegra support, covering Tegra20 and Tegra30
- new camera sensor drivers: T4ka3 and ov2732
- m88ds3103: add 3103c chip support
- uvcvideo: add support for Intel RealSense D436/D555 and P010 pixel format
- synopsys csi2rx: add i.MX93 support
- imx8-isi: add i.MX95 support
- imx8mq-mipi-csi2: add i.MX8ULP support
- dw100: add V4L2 requests support
- support for DTV devices from Hauppauge got some improvements
- media staging: dropped starfive-camss driver
- media docs: document multi-committers model and improve maint profile
- media core:
- add v4l2_subdev_get_frame_desc_passthrough() helper
- improve error handling in fwnode parsing
- lots of driver fixes, cleanups and improvements
* tag 'media/v7.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (251 commits)
Revert "media: cx231xx: add USB ID 2040:8360 for Hauppauge WinTV-HVR-935"
media: synopsys: csi2rx: add i.MX93 support
media: dt-bindings: add NXP i.MX93 compatible string
media: synopsys: csi2rx: Use enum and u32 array for register offsets
media: synopsys: csi2rx: implement .get_frame_desc() callback
media: synopsys: csi2rx: only check errors from devm_clk_bulk_get_all()
media: synopsys: csi2rx: use devm_reset_control_get_optional_exclusive()
media: i2c: imx283: add support for non-continuous MIPI clock mode
media: i2c: ov08d10: add support for 24 MHz input clock
media: i2c: ov08d10: add support for reset and power management
media: i2c: ov08d10: add support for binding via device tree
dt-bindings: media: i2c: document Omnivision OV08D10 CMOS image sensor
media: i2c: ov08d10: add missing newline to prints
media: i2c: ov08d10: fix some typos in comments
media: i2c: ov08d10: remove duplicate register write
media: i2c: ov08d10: fix image vertical start setting
media: i2c: ov08d10: fix runtime PM handling in probe
staging: media: ipu7: Update TODO
media: Add t4ka3 camera sensor driver
media: i2c: Add ov2732 image sensor driver
...
|
|
mdp_vpu_sendmsg() passes the buffer to scp_ipi_send(), which takes now
pointer to const, so adjust this interface as well for increased code
safety and code readability.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260317-rpmsg-send-const-v3-5-4d7fd27f037f@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
This reverts commit bb2a3912549d3b5cef5ed27200402fe8f6fb0694.
The USB ID 2040:8360 was reported as a new revision
of Hauppauge HVR-935 and requested to be added to
the cx231xx driver. The issue is current generation
of Hauppauge 9x5 devices including 935, 955, and 975
have moved to em2828x usb bridge. Support for the
em2828x usb bridge and USB ID's for the new devices
has been submitted.
Signed-off-by: Bradford Love <brad@nextdimension.cc>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
|
|
The i.MX93 uses a newer version of the DW CSI-2 controller with a changed
register layout and an integrated Image Pixel Interface (IPI), which
converts the received CSI-2 packets from byte to pixel format and produces
a pixel data bus containing vertical and horizontal synchronization
information.
The reset flow also differs, so add the .assert_reset(), .deassert_reset(),
and .idi_enable() callbacks to support it.
Reviewed-by: Michael Riesch <michael.riesch@collabora.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
[Sakari Ailus: include missing linux/bitfield.h.]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
|
|
Use enum dw_mipi_csi2rx_regs_index together with a u32 array to describe
register offsets. This allows supporting new IP versions with different
register layouts in a structured way.
Add rk3568_regs matching the previous macro definitions and pass it as
driver data during probe.
No functional change intended.
Reviewed-by: Michael Riesch <michael.riesch@collabora.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
|
|
Implement the .get_frame_desc() callback to fetch information from the
remote endpoint.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Michael Riesch <michael.riesch@collabora.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
|
|
devm_clk_bulk_get_all() returns all clocks described in the DT, which are
already validated by the binding. Do not need enforce an expected clock
count.
Only check for error returns (< 0) to support more SoCs.
Reviewed-by: Michael Riesch <michael.riesch@collabora.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
|
|
The DW MIPI CSI-2 RX is used on different SoCs, not all of which provide a
reset controller. Switch to devm_reset_control_get_optional_exclusive()
to support such platforms.
Reset presence and numbering are validated by the DT binding.
Reviewed-by: Michael Riesch <michael.riesch@collabora.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
|
|
Add support for selecting between continuous and non-continuous MIPI clock
mode.
Previously, the CSI-2 non-continuous clock endpoint flag was ignored and
the sensor was always configured for non-continuous clock mode. For
existing device tree nodes that do not have this property enabled, this
update will therefore change the actual clock mode.
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Matthias Fend <matthias.fend@emfend.at>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
|
|
The sensor supports an input clock in the range of 6 to 27 MHz. Currently,
the driver only supports a 19.2 MHz clock. Extend the driver so that at
least 24 MHz, which is a typical frequency for this sensor, can also be
used.
Signed-off-by: Matthias Fend <matthias.fend@emfend.at>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
|
|
Add support for the required power supplies as well as the control of an
optional sensor reset.
Signed-off-by: Matthias Fend <matthias.fend@emfend.at>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
|
|
The OV08D10 can be used also on embedded designs using device tree so allow
the sensor to bind to a device tree node.
Signed-off-by: Matthias Fend <matthias.fend@emfend.at>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
|
|
Add trailing \n to dev_* prints where missing.
Signed-off-by: Matthias Fend <matthias.fend@emfend.at>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
|
|
Fix some spelling errors in comments.
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Matthias Fend <matthias.fend@emfend.at>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
|
|
Register P1:0x33 is written twice with the same value in the
'lane_2_mode_1632x1224' sequence. Remove one unnecessary write access.
Signed-off-by: Matthias Fend <matthias.fend@emfend.at>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
|
|
The current settings for the "image vertical start" register appear to be
incorrect. While this only results in an incorrect start line for native
modes, this faulty setting causes actual problems in binning mode. At least
on an i.MX8MP test system, only corrupted frames could be received.
To correct this, the recommended settings from the reference register sets
are used for all modes. Since this shifts the start by one line, the Bayer
pattern also changes, which has also been corrected.
Fixes: 7be91e02ed57 ("media: i2c: Add ov08d10 camera sensor driver")
Cc: stable@vger.kernel.org
Signed-off-by: Matthias Fend <matthias.fend@emfend.at>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
|
