| Age | Commit message (Collapse) | Author |
|---|
|
The PDC irqchip driver updates IRQ_ENABLE and IRQ_CFG for three different
versions v2.7, v3.0 and v3.2. These registers are organized in hardware as
below on various SoCs:
+---------------------------------------------------------------+
| SM8350, SM8450 | SM8550, Hamoa | SM8650, SM8750 |
|---------------------------------------------------------------|
| v2.7 | v3.0 | v3.2 |
|---------------------------------------------------------------|
| IRQ_ENABLE_BANK | IRQ_ENABLE_BANK | NA |
|---------------------------------------------------------------|
| IRQ_CFG | IRQ_CFG | IRQ_CFG |
| | | |
| | | [31:6] Unused |
| | [31:5] Unused | [5] GPIO_STATUS |
| | [4] GPIO_STATUS| [4] GPIO_MASK |
| [31:3] Unused | [3] GPIO_MASK | [3] IRQ_ENABLE |
| [0:2] Type | [0:2] Type | [0:2] Type |
+---------------------------------------------------------------|
All SoCs PDC chips support "pass through mode" in which all interrupts are
forwarded to the GIC without any latching in the PDC hardware.
So far the driver did not utilize GPIO_STATUS and GPIO_MASK from IRQ_CFG
register for v3.0 and v3.2 since they are only needed to be configured when
PDC runs in a specific mode named "second level interrupt controller". In
that mode it can latch the GPIO interrupts in GPIO_STATUS and forward GPIO
interrupts to GIC as LEVEL_HIGH type SPI interrupt.
All the SoCs defaulted to pass through mode with the exception of some x1e
types. x1e PDC may be set to secondary controller mode for builds on CRD
boards whereas it may be set to pass through mode for IoT-EVK boards.
Restructure in preparation to add the second level interrupt controller
mode utilizing GPIO_STATUS and GPIO_MASK bits which changed the bit
positions between v3.0 and v3.2.
No functional change intended.
[ tglx: Massaged change log ]
Signed-off-by: Maulik Shah <maulik.shah@oss.qualcomm.com>
Signed-off-by: Thomas Gleixner <tglx@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://patch.msgid.link/20260707-hamoa_pdc_v3-v4-1-dfd1f4a3ae89@oss.qualcomm.com
|
|
A non-global perfmon is meant to count events generated by a specific
submission, but the scheduler can run jobs from different queues
concurrently on the same V3D core. Without explicit serialization, an
unrelated job running in parallel with a perfmon-carrying job pollutes
the counters and generates unusable results.
To address such issue, we must enforce cross-queue serialization when we
detect a perfmon-carrying submission. It's possible to implement
serialization by enforcing two rules:
1. A job that carries a non-global perfmon must wait for every job
currently in-flight across all HW queues to finish.
2. While a perfmon-carrying job is still in-flight, all subsequently
submitted jobs must wait for it.
Note that serialization is not needed in the global perfmon case, as the
global perfmon tracks activity from all jobs, so concurrency is desirable.
Therefore, check if serialization is needed during job submission and if
so, attach fence dependences to enforce cross-queue serialization.
Reviewed-by: Iago Toral Quiroga <itoral@igalia.com>
Link: https://patch.msgid.link/20260706-v3d-perfmon-lifetime-v4-2-d7b312ff2c83@igalia.com
Signed-off-by: Maíra Canal <mcanal@igalia.com>
|
|
v3d exposes a single set of performance counters per core, so at any
moment at most one performance monitor can be programmed in HW. In
software, this singleton is represented by v3d_dev->active_perfmon, but
until now nothing actually serialized access to it: scheduler callbacks,
the GPU-reset path, and perfmon ioctls all read and wrote that field
lock-free.
The existence of v3d_perfmon->lock mutex did not close the gap. It
serialized start/stop of *one* perfmon object against itself, but the
invariant that needs protection is device-wide: there can be exactly one
active perfmon at any moment in HW. Two threads acting on different
perfmon objects could race through v3d_dev->active_perfmon and the
counter registers, leaving software and HW out of sync.
This commit moves the locking to where the invariant actually lives. Group
the active perfmon pointer with a device-wide spinlock and route every
state transition (job start, job completion, set global, reset,
suspend/resume, destruction) through a small set of locked entry points
that are the only mutators of the HW counters.
Some design improvements needed to be made for the refactor:
1. Stop the perfmon from the IRQ handler at job-completion time (the
natural boundary for "active perfmon follows the active job"). This
required a change from a mutex to a spinlock. This solves another
issue of the existing design: perfmon start/stop was exclusively
attached to run_job() callbacks, which means that if nothing was
further queued up, a perfmon would never actually be stopped.
2. Pause/resume the HW counters across runtime-PM transitions without
dropping the software reference. This preserves the perfmon state
while the device is idle.
3. Move the global perfmon lifecycle management to the set_global
IOCTL. This simplifies the logic in v3d_perfmon_start() and
v3d_perfmon_stop(), as there is no need to always check if the
global perfmon is enabled.
4. v3d_perfmon_get_values_ioctl() doesn't stop the perfmon when
capturing the values. All lifecycle management is handled by the
job (for per-job perfmons) or the set_global IOCTL (for global
perfmons).
Reviewed-by: Iago Toral Quiroga <itoral@igalia.com>
Link: https://patch.msgid.link/20260706-v3d-perfmon-lifetime-v4-1-d7b312ff2c83@igalia.com
Signed-off-by: Maíra Canal <mcanal@igalia.com>
|
|
PMFW reports the S0i3 subsystem accounting per SoC, and the set of IP
blocks and their bit ordering differ across SoC generations. Family
1Ah, Model 80h accounts for a distinct set of 19 IP blocks, which does
not match the ordering in soc15_ip_blk[].
Commit 043af31c8d30 ("platform/x86/amd/pmc: Add PMC driver support for
AMD 1Ah M80H SoC") wired amd_1ah_m80_cpu_info to soc15_ip_blk[], so
M80H has been reporting incorrect S0i3 accounting via debugfs.
Add soc15_ip_blk_v3[] with the correct ordering and point
amd_1ah_m80_cpu_info at it.
Fixes: 043af31c8d30 ("platform/x86/amd/pmc: Add PMC driver support for AMD 1Ah M80H SoC")
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Reviewed-by: Mario Limonciello (AMD) <superm1@kernel.org>
Link: https://patch.msgid.link/20260707122852.2066987-1-Shyam-sundar.S-k@amd.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
The previously integrated power limits for the ASUS ROG Strix G16 G614PR
laptop model were incorrect and too low compared to the windows counterparts.
Update the power limits to the correct specifications based on the
platform's hardware capabilities:
- Increase AC PL1/SPL max limit from 90W to 120W.
- Increase AC PL2/SPPT default/max from 110W/125W to 140W/145W.
- Increase AC PL3/FPPT default/max from 110W/125W to 140W/145W.
Fixes: 6b3bbe770f4ca0439710b7c42f88b9f6eeebabd0 (platform/x86: asus-armoury: add support for G614PR)
Fixes: https://lore.kernel.org/platform-driver-x86/20260610152130.25892-1-scardracs@disroot.org/
Signed-off-by: Marco Scardovi <scardracs@disroot.org>
Link: https://patch.msgid.link/20260630142957.7751-1-scardracs@disroot.org
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
amdxdna_update_heap() iterates over hardware contexts while holding
xdna->dev_lock. During the iteration, amdxdna_pm_resume_get_locked() may
temporarily release and reacquire the lock, allowing hardware contexts to
be modified concurrently.
Fix the race by calling amdxdna_pm_resume_get_locked() before
iterating over hardware contexts.
Fixes: dbc8fd7a03cb ("accel/amdxdna: Add expandable device heap support")
Reviewed-by: Max Zhen <max.zhen@amd.com>
Signed-off-by: Lizhi Hou <lizhi.hou@amd.com>
Link: https://patch.msgid.link/20260707055818.479165-1-lizhi.hou@amd.com
|
|
Both amdxdna_hwctx_sync_debug_bo() and amdxdna_drm_config_hwctx_ioctl()
hold xdna->dev_lock while invoking backend operations. If the hardware
hangs, aie2_cmd_wait() blocks waiting for a firmware response. When the
DRM scheduler timeout expires, aie2_sched_job_timedout() is invoked to
reset the hardware. However, the timeout handler also attempts to acquire
dev_lock, resulting in a deadlock.
Avoid this by releasing dev_lock before waiting for the firmware
response and reacquiring it after the wait completes. This allows the
timeout handler to proceed with device recovery when a debug BO command
times out.
Fixes: 7ea046838021 ("accel/amdxdna: Support firmware debug buffer")
Reviewed-by: Max Zhen <max.zhen@amd.com>
Signed-off-by: Lizhi Hou <lizhi.hou@amd.com>
Link: https://patch.msgid.link/20260707055732.479103-1-lizhi.hou@amd.com
|
|
amdxdna_gem_obj_open() increments open_ref before attempting to set up
the DMA address mapping. When amdxdna_dma_map_bo() fails, the function
returned immediately without rolling back either change made on the first
open (open_ref == 1 path).
Fix it by decrementing open_ref and clearing abo->client on the error path.
Fixes: ece3e8980907 ("accel/amdxdna: Allow forcing IOVA-based DMA via module parameter")
Reviewed-by: Max Zhen <max.zhen@amd.com>
Signed-off-by: Lizhi Hou <lizhi.hou@amd.com>
Link: https://patch.msgid.link/20260707055658.479049-1-lizhi.hou@amd.com
|
|
amdxdna_umap_release() calls the blocking mmu_interval_notifier_remove()
before removing the object from abo->mem.umap_list. If
aie2_populate_range() runs concurrently, it may obtain a reference to an
amdxdna_umap that is being released, leading to a potential use-after-free.
Use kref_get_unless_zero() in aie2_populate_range() when acquiring a
reference. If the reference count has already dropped to zero, release
is in progress and the entry is skipped.
Fixes: e486147c912f ("accel/amdxdna: Add BO import and export")
Reviewed-by: Max Zhen <max.zhen@amd.com>
Signed-off-by: Lizhi Hou <lizhi.hou@amd.com>
Link: https://patch.msgid.link/20260706221228.434099-1-lizhi.hou@amd.com
|
|
Use kmalloc_objs instead of kmalloc_array when initializing chains in
drm_syncobj_timeline_signal_ioctl.
Concern caught by static analysis.
Suggested-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Jonathan Cavitt <jonathan.cavitt@intel.com>
Cc: Tobias Hector <Tobias.Hector@amd.com>
Cc: Jason Ekstrand <jason@jlekstrand.net>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Chunming Zhou <david1.zhou@amd.com>
Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: https://patch.msgid.link/20260701143111.1410442-1-jonathan.cavitt@intel.com
|
|
At the moment, concurrent writes from userspace and the kernel to the
console can trigger a race condition that results in an infinite loop of
the same messages printed over and over again. This is most likely to
happen during system startup or shutdown when the init system starts/stops
a large number of system services that interact with various kernel code.
When userspace writes to the TTY device, the driver initiates an
asynchronous DMA transfer and releases the port lock. At the same moment,
the kernel printk path might grab the port lock and re-configure the UART
controller for PIO, without waiting for the DMA operation to complete. It
seems like this collision results in zero progress being reported for the
DMA engine, so the same text is printed to the console over and over again.
For the kernel console, we want a reliable output path that will be
functional even during crashes etc. So rather than implementing complex
code to synchronize the kernel console write routines with the userspace
DMA write routines, simply disable DMA for the console UART instance.
Similar checks exist in many other serial drivers, e.g. 8250_port.c,
imx.c, sh-sci.c etc.
Cc: stable <stable@kernel.org>
Fixes: 3a878c430fd6 ("tty: serial: msm: Add TX DMA support")
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Acked-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://patch.msgid.link/20260706-serial-msm-console-dma-collision-v1-1-3179b8cb1d89@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It's strongly recommended for GPIO drivers to always implement the
.get_direction() callback - even when the direction is tracked in
software. The GPIO core emits a warning when the callback is missing
and a user reads the direction of a line, e.g. via
/sys/kernel/debug/gpio.
The MAX310X keeps the GPIO direction in the GPIOCFG register (a set bit
selects output), which the existing direction_input/output callbacks
already program, so the current direction can be read back directly.
Fixes: f65444187a66 ("serial: New serial driver MAX310X")
Cc: stable <stable@kernel.org>
Signed-off-by: Tapio Reijonen <tapio.reijonen@vaisala.com>
Reviewed-by: Linus Walleij <linusw@kernel.org>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Reviewed-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://patch.msgid.link/20260615-b4-serial-max310x-gpio-get-direction-v2-1-4704ba2b181a@vaisala.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
guard()s express more clearly what the lock protects and let the
function return immediately instead of jumping to an unlock label.
Signed-off-by: John de la Garza <john@jjdev.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://patch.msgid.link/20260701231215.4092457-1-john@jjdev.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Convert the manual spin_lock_irq()/rcu_read_lock() nesting in tiocspgrp()
to scoped guard()s. This drops the out_unlock and out_unlock_ctrl labels
and lets the error paths return directly.
No functional change intended.
Signed-off-by: John de la Garza <john@jjdev.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://patch.msgid.link/20260701030139.3189030-1-john@jjdev.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The MAX310x DT binding pulls in /schemas/serial/rs485.yaml via its allOf
list, advertising the rs485-* properties defined there - none of which
were honoured at runtime, because the driver never called
uart_get_rs485_mode().
All channels share the parent SPI/I2C device, so uart_get_rs485_mode()
called directly on each port would read the same chip-level fwnode for
every call. Walk dev->of_node's children for the "serial@N" subnode
with matching reg, and temporarily retarget the parent device's fwnode
while uart_get_rs485_mode() runs, so each channel picks up its own
subnode's properties. Probe is serialised, so the swap is safe.
For single-channel variants (max3107, max3108), fall back to the chip's
own fwnode when no subnode is present, so existing DTs that declare
rs485 properties at the top level keep working.
Signed-off-by: Tapio Reijonen <tapio.reijonen@vaisala.com>
Link: https://patch.msgid.link/20260615-b4-max310x-rs485-dt-v3-3-7e79f064bdd7@vaisala.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The MAX310x exposes four GPIOs per UART port via an in-driver
gpio_chip. devm_gpiochip_add_data() used to run after the per-port
uart_add_one_port() loop, so a device-tree consumer referencing one of
the chip's own GPIOs (for example rs485-term-gpios = <&max310x 0 ...>)
could not resolve it during port registration: the GPIO provider it
waits for is the very driver still trying to register, and the lookup
returns -EPROBE_DEFER on its own provider, deferring probe forever.
Split the per-port setup into two passes around the gpio_chip
registration:
1. Initialise per-port state - port struct fields, regmap binding,
IRQ disable, work queues. The gpio_chip callbacks dereference
s->p[i].regmap via to_max310x_port() and become callable as soon
as the chip is visible to gpiolib, so every entry must be
populated first.
2. devm_gpiochip_add_data() - register the gpio_chip.
3. Allocate a line, uart_add_one_port(), set_bit(), max310x_power().
Keeping line allocation, registration and set_bit() together
preserves the existing "bit set <=> port registered" rollback
invariant that out_uart relies on.
Signed-off-by: Tapio Reijonen <tapio.reijonen@vaisala.com>
Link: https://patch.msgid.link/20260615-b4-max310x-rs485-dt-v3-1-7e79f064bdd7@vaisala.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
vcs_read() and vcs_write() allocate staging buffers with
__get_free_pages().
These buffers can be allocated with kmalloc() as there's nothing special
about them to go directly to the page allocator.
kmalloc() provides a better API that does not require ugly casts and it's a
modern way of saying "I need a page-sized buffer"
Replace use of __get_free_page() with kmalloc() and drop unused now
DEFINE_FREE(free_page_ptr ...)
Link: https://lore.kernel.org/all/700c5a5f-3128-4671-99aa-827ca73f5cdf@kernel.org
Link: https://lore.kernel.org/all/635405e4-9423-4a25-a6e7-e03c8ea0bcbe@redhat.com
Signed-off-by: Mike Rapoport (Microsoft) <rppt@kernel.org>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://patch.msgid.link/20260528-b4-tty-v1-4-9da9f7aec5f2@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
men_z135_probe() allocates a receive staging buffer filled by the
CPU via memcpy_fromio() from the device MMIO region.
This buffer can be allocated with kmalloc() as there's nothing special
about it to go directly to the page allocator.
kmalloc() provides a better API that does not require ugly casts and
kfree() does not need to know the size of the freed object.
Replace use of __get_free_page() with kmalloc() and free_page() with
kfree().
Link: https://lore.kernel.org/all/635405e4-9423-4a25-a6e7-e03c8ea0bcbe@redhat.com
Signed-off-by: Mike Rapoport (Microsoft) <rppt@kernel.org>
Link: https://patch.msgid.link/20260528-b4-tty-v1-3-9da9f7aec5f2@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
rs_startup() allocates a transmit ring buffer that is used to buffer reads
and writes from/to serial data register.
This buffer can be allocated with kmalloc() as there's nothing special
about it to go directly to the page allocator.
kmalloc() provides a better API that does not require ugly casts and
kfree() does not need to know the size of the freed object.
Replace use of get_zeroed_page() with kzalloc() and free_page() with
kfree().
Link: https://lore.kernel.org/all/635405e4-9423-4a25-a6e7-e03c8ea0bcbe@redhat.com
Signed-off-by: Mike Rapoport (Microsoft) <rppt@kernel.org>
Link: https://patch.msgid.link/20260528-b4-tty-v1-2-9da9f7aec5f2@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
pch_uart_init_port() allocates a staging buffer for non-DMA receive path
using __get_free_page().
This buffer can be allocated with kmalloc() as there's nothing special
about it to go directly to the page allocator.
kmalloc() provides a better API that does not require ugly casts and
kfree() does not need to know the size of the freed object.
Replace use of __get_free_page() with kmalloc() and free_page() with
kfree().
Link: https://lore.kernel.org/all/635405e4-9423-4a25-a6e7-e03c8ea0bcbe@redhat.com
Signed-off-by: Mike Rapoport (Microsoft) <rppt@kernel.org>
Link: https://patch.msgid.link/20260528-b4-tty-v1-1-9da9f7aec5f2@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use kvmalloc_objs instead of kvmalloc_array when initializing
exec->objects in drm_exec_init.
Concern caught by static analysis.
Signed-off-by: Jonathan Cavitt <jonathan.cavitt@intel.com>
Cc: Rob Clark <robdclark@chromium.org>
Cc: Christian König <christian.koenig@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: https://patch.msgid.link/20260701172458.1416930-1-jonathan.cavitt@intel.com
|
|
The trace events in drivers/ufs/core/ufs_trace.h were converted to take a
pointer to the hba structure as an argument for the tracepoint and then in
TP_printk() the printing of the dev_name from the ring buffer was
converted to using the dev dereferenced pointer from the hba saved
pointer.
This is not allowed as the TP_printk() is executed at the time the trace
event is read from /sys/kernel/tracing/trace file. That can happen
literally, seconds, minutes, hours, weeks, days, or even months later!
There is no guarantee that the hba pointer will still exist by the time it
is dereferenced when the "trace" file is read.
Instead, save the device name from the hba pointer at the time the
tracepoint is called and place it into the ring buffer event. Then the
TP_printk() can read the name directly from the ring buffer and remove the
possibility that it will read a freed pointer and crash the kernel.
This was detected when testing the trace event code that looks for
TP_printk() parameters doing illegal derferences[1]
[1] https://lore.kernel.org/all/20260630184836.74d477b6@gandalf.local.home/
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20260630185412.283c26c5@gandalf.local.home
Fixes: 583e518e71003 ("scsi: ufs: core: Add hba parameter to trace events")
Reviewed-by: Peter Wang <peter.wang@mediatek.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
Add driver for the Qualcomm interconnect buses found in Maili
based platforms. The topology consists of several NoCs that are
controlled by a remote processor that collects the aggregated
bandwidth for each master-slave pairs.
Co-developed-by: Odelu Kukatla <odelu.kukatla@oss.qualcomm.com>
Signed-off-by: Odelu Kukatla <odelu.kukatla@oss.qualcomm.com>
Signed-off-by: Raviteja Laggyshetty <raviteja.laggyshetty@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://patch.msgid.link/20260622-maili_icc-v2-2-18b5ac08c04f@oss.qualcomm.com
Signed-off-by: Georgi Djakov <djakov@kernel.org>
|
|
Add Epoch Subsystem (EPSS) L3 interconnect provider support on
Qualcomm Shikra SoC.
The EPSS L3 block on Shikra SoC is similar to existing Qualcomm EPSS/OSM
L3 providers, but supports only up to 12 frequency lookup table entries.
Reading beyond the supported LUT entries can expose incorrect frequencies.
Add shikra-specific EPSS descriptor shikra_epss_l3_perf_state that reuses
existing EPSS configuration with appropriate LUT entries limit.
Co-developed-by: Odelu Kukatla <odelu.kukatla@oss.qualcomm.com>
Signed-off-by: Odelu Kukatla <odelu.kukatla@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Raviteja Laggyshetty <raviteja.laggyshetty@oss.qualcomm.com>
Link: https://patch.msgid.link/20260603-shikra_epss_l3-v3-2-3c2e0b796e78@oss.qualcomm.com
Signed-off-by: Georgi Djakov <djakov@kernel.org>
|
|
Use the descriptor's `ep_mem_offset` to calculate the start of the endpoint
memory access array and to comply with the FF-A spec instead of defaulting
to `sizeof(struct ffa_mem_region)`.
This requires moving `ffa_mem_region_additional_setup()` earlier in the setup
flow.
Also, add sanity checks to ensure the calculated descriptor offsets do not
exceed `max_fragsize`.
Fixes: 113580530ee7 ("firmware: arm_ffa: Update memory descriptor to support v1.1 format")
Reviewed-by: Sudeep Holla <sudeep.holla@kernel.org>
Signed-off-by: Mostafa Saleh <smostafa@google.com>
Signed-off-by: Sebastian Ene <sebastianene@google.com>
Link: https://patch.msgid.link/20260702103848.1647249-3-sebastianene@google.com
Signed-off-by: Marc Zyngier <maz@kernel.org>
|
|
Sashiko (locally) reports multiple out-of-bound issues in
ffa_setup_and_transmit:
1) Writing ep_mem_access->reserved can write out of bounds for FFA
versions < 1.2 as ffa_emad_size_get() returns 16 bytes in that case
while reserved has an offset of 24.
Instead of zeroing fields, memset the struct to zero first based on
the FFA version.
2) Make sure there is enough size to write constituents.
While at it, convert the only sizeof() in the driver that uses a
type instead of variable.
Reviewed-by: Sudeep Holla <sudeep.holla@kernel.org>
Fixes: 111a833dc5cb ("firmware: arm_ffa: Set reserved/MBZ fields to zero in the memory descriptors")
Signed-off-by: Mostafa Saleh <smostafa@google.com>
Signed-off-by: Sebastian Ene <sebastianene@google.com>
Link: https://patch.msgid.link/20260702103848.1647249-2-sebastianene@google.com
Signed-off-by: Marc Zyngier <maz@kernel.org>
|
|
This series enables QoS configuration for QNOC type device which
can be found on X1E80100 platform. It enables QoS configuration
for master ports with predefined priority and urgency forwarding.
This helps in prioritizing the traffic originating from different
interconnect masters at NOC (Network On Chip).
The system may function normally without this feature. However,
enabling QoS helps optimize latency and bandwidth across subsystems
like CPU, GPU, and multimedia engines, which becomes important in
high-throughput scenarios. This is a feature aimed at performance
enhancement to improve system performance under concurrent workloads.
* icc-x1e80100
dt-bindings: interconnect: qcom,x1e80100-rpmh: add clocks property to enable QoS
interconnect: qcom: x1e80100: enable QoS configuration
Link: https://patch.msgid.link/20260527-x1e80100_qos-v2-0-305c6539e6d2@oss.qualcomm.com
Signed-off-by: Georgi Djakov <djakov@kernel.org>
|
|
Enable QoS configuration for master ports with predefined priority
and urgency forwarding.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Raviteja Laggyshetty <raviteja.laggyshetty@oss.qualcomm.com>
Link: https://patch.msgid.link/20260527-x1e80100_qos-v2-2-305c6539e6d2@oss.qualcomm.com
Signed-off-by: Georgi Djakov <djakov@kernel.org>
|
|
netif_close_many will soon assert ops lock (for locked DOWN/GOING_DOWN).
Update mtk_eth_set_dma_device to manually grab and release the ops lock.
Signed-off-by: Stanislav Fomichev <sdf@fomichev.me>
Link: https://patch.msgid.link/20260702224150.3730033-4-sdf@fomichev.me
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The client cap is currently advertised unconditionally, even for drivers
that do not support plane color pipelines. If clients supporting the latter,
like Wayland compositors or tools like drm_info, enable the client cap on
such drivers they will be left without both color pipeline and the legacy
properties COLOR_ENCODING and COLOR_RANGE, effectively breaking YUV->RGB
conversion support.
Prevent that by only marking the cap supported if there are actually planes
with color pipelines.
Note: while the color pipeline replacement for the legacy properties is
still under review (1), we can assume that it will work as a drop-in
replacement. That means any plane on any hardware currently supporting
the legacy properties will be able to offer a functionally equal color
pipeline and there will be no technical reason keep using the legacy
properties if both the driver and the client support the new API.
[1] https://lore.kernel.org/dri-devel/20260623164812.81110-1-harry.wentland@amd.com/
Signed-off-by: Robert Mader <robert.mader@collabora.com>
Reviewed-by: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Reviewed-by: Melissa Wen <mwen@igalia.com>
Fixes: 179ab8e7d7b3 ("drm/colorop: Introduce DRM_CLIENT_CAP_PLANE_COLOR_PIPELINE")
Link: https://patch.msgid.link/20260703073230.19982-1-robert.mader@collabora.com
Suggested-by: Maarten Lankhorst <dev@lankhorst.se>
Signed-off-by: Maarten Lankhorst <dev@lankhorst.se>
|
|
GPIO interrupts may retain stale state across warm reboots when
peripherals remain powered. If a GPIO line is not explicitly
configured for interrupts, this can result in interrupt storms
due to missing handlers.
Fix this by ensuring all interrupts are masked and disabled at
hardware initialization time via the init_hw() callback. Pending
interrupts are also cleared to start from a known-safe state.
Interrupts will be unmasked only when explicitly configured by
userspace or kernel drivers.
Signed-off-by: Liang Hao <haohlliang@gmail.com>
Link: https://patch.msgid.link/20260705074759.47863-1-haohlliang@gmail.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
|
|
GPIO consumers such as gpio-keys can enable IRQ wake and adjust the wake
trigger type from their suspend callbacks. If the DWAPB controller suspends
first, masking interrupts and disabling its clocks in the normal suspend
phase prevents that late wake configuration from reliably reaching the
hardware. Systems with real DWAPB bus clocks then fail to wake from s2idle
through GPIO keys.
Save the register context in the normal suspend callback, but defer IRQ
masking and clock gating until suspend_noirq. At that point all consumers
have finished configuring wake IRQs, so keep the clocks enabled when wake
lines are armed and only gate them when no wake source is active.
Resume_noirq reenables clocks, if they were gated, before the normal resume
path restores registers.
Propagate wake requests to the parent irqchip while keeping the local wake
mask in sync with failures.
Fixes: 6437c7ba69c3 ("gpio: dwapb: Add wakeup source support")
Signed-off-by: Jia Wang <wangjia@ultrarisc.com>
Link: https://patch.msgid.link/20260702-gpio-dwapb-wakeup-v2-1-203f2f33429f@ultrarisc.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
|
|
The .driver_data member of the struct pci_device_id array were
initialized by list expressions relying on hidden assignment of .class
and .class_mask in PCI_VDEVICE().
Make the initialization more robust by using a named initializer. This
robustness is relevant for a planned change to struct pci_device_id that
replaces .driver_data by an anonymous union.
This change doesn't introduce changes to the compiled pci_device_id
array. Tested on x86 and arm64.
Signed-off-by: Uwe Kleine-König (The Capable Hub) <u.kleine-koenig@baylibre.com>
Link: https://patch.msgid.link/20260524131905.871222-2-u.kleine-koenig@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The .driver_data member of the struct pci_device_id array were
initialized by list expressions. This isn't easily readable if you're
not into PCI, still more given that it's hidden in macros. Using named
initializers is more explicit and thus easier to parse for a human. And
it's also more robust against changes to the struct definition.
The mentioned robustness is relevant for a planned change to struct
pci_device_id that replaces .driver_data by an anonymous union.
Also drop a few explicit zeros that are not needed and improve
indention.
This change doesn't introduce changes to the compiled pci_device_id
array. Tested on x86 and arm64.
Signed-off-by: Uwe Kleine-König (The Capable Hub) <u.kleine-koenig@baylibre.com>
Link: https://patch.msgid.link/20260522140103.769262-2-u.kleine-koenig@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The drm_exec component uses a variable with scope limited to the for() and
an indirect goto to allow instantiating multiple macros in the same
function.
This unfortunately doesn't work well with certain compilers when the
indirect goto can't be lowered to a direct jump.
Switch the indirect goto to a direct goto, the drawback is that we now
can't use the dma_exec_until_all_locked() macro in the same function
multiple times.
The is currently only one user of this and only as a hacky workaround
which is about to be removed.
So document that the __label__ statement should be used when the macro is
used multiple times and fix the tests and the only use case where that is
necessary.
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Christian König <christian.koenig@amd.com>
Fixes: 9920249a5288 ("drm/amdgpu: convert amdgpu_vm_lock_by_pasid() to drm_exec")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202606231854.7LeCtlLe-lkp@intel.com/
Closes: https://lore.kernel.org/oe-kbuild-all/202606232356.gwHMAJAW-lkp@intel.com/
Closes: https://lore.kernel.org/oe-kbuild-all/202606240753.kYjobJVl-lkp@intel.com/
Closes: https://lore.kernel.org/oe-kbuild-all/202606241110.iUga5vVw-lkp@intel.com/
Closes: https://lore.kernel.org/oe-kbuild-all/202607031446.1PWG18mN-lkp@intel.com/
Closes: https://lore.kernel.org/oe-kbuild-all/202607031837.HSmBj8pr-lkp@intel.com/
Closes: https://lore.kernel.org/oe-kbuild-all/202607040159.GopyEswS-lkp@intel.com/
Tested-by: Mikhail Gavrilov <mikhail.v.gavrilov@gmail.com>
Reviewed-by: Dave Airlie <airlied@redhat.com>
Link: https://lore.kernel.org/r/20260704084133.122053-1-christian.koenig@amd.com
|
|
Enable static QoS configuration for SC8280XP NoC master ports with
predefined priority and urgency forwarding values.
Add the QoS box data for the SC8280XP providers, add regmap configurations
for the real NoCs, and mark only aggre1_noc and aggre2_noc as requiring
clocks for QoS register access.
Signed-off-by: Xilin Wu <sophon@radxa.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://patch.msgid.link/20260507-sc8280xp-qos-v1-2-15135858cd98@radxa.com
Signed-off-by: Georgi Djakov <djakov@kernel.org>
|
|
Convert update_attrib() to return 0 on success and a
negative errno on failure. Update rtw_xmit() to handle
the returned error code.
No functional change intended.
Signed-off-by: Hungyu Lin <dennylin0707@gmail.com>
Link: https://patch.msgid.link/20260707112503.612-5-dennylin0707@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Convert update_attrib_sec_info() to return 0 on success and
a negative errno on failure.
No functional change intended.
Signed-off-by: Hungyu Lin <dennylin0707@gmail.com>
Link: https://patch.msgid.link/20260707112503.612-4-dennylin0707@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Replace goto-based error handling with direct returns and
remove the temporary res variable.
No functional change.
Signed-off-by: Hungyu Lin <dennylin0707@gmail.com>
Link: https://patch.msgid.link/20260707112503.612-3-dennylin0707@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Replace goto-based error handling with direct returns and
remove the temporary res variable.
No functional change.
Signed-off-by: Hungyu Lin <dennylin0707@gmail.com>
Link: https://patch.msgid.link/20260707112503.612-2-dennylin0707@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
and rtw_get_wps_attr()
Three IE/attribute parsing functions have missing bounds checks.
rtw_get_sec_ie() and rtw_get_wapi_ie() iterate over a raw IE buffer
without verifying that the header bytes (tag + length) are within the
remaining buffer before reading them. Additionally, rtw_get_sec_ie()
compares the 4-byte WPA OUI at cnt+2 without checking that at least
6 bytes remain, and rtw_get_wapi_ie() compares a 4-byte WAPI OUI at
cnt+6 without checking that at least 10 bytes remain.
rtw_get_wps_attr() reads wps_ie[0] and wps_ie+2 unconditionally at
entry, before verifying that wps_ielen is large enough to contain
the 6-byte WPS IE header (element_id + length + 4-byte OUI). Inside
the attribute loop, get_unaligned_be16() is called on attr_ptr and
attr_ptr+2 without checking that 4 bytes remain in the buffer.
Add a cnt+2 bounds check before each loop body in rtw_get_sec_ie()
and rtw_get_wapi_ie(), guard each multi-byte comparison with a minimum
IE length requirement, add a wps_ielen < 6 early return in
rtw_get_wps_attr(), and add a 4-byte bounds check in its inner loop.
Fixes: 554c0a3abf21 ("staging: Add rtl8723bs sdio wifi driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Alexandru Hossu <hossu.alexandru@gmail.com>
Link: https://patch.msgid.link/20260522004531.1038924-8-hossu.alexandru@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The loop in is_ap_in_tkip() iterates over IEs without verifying that
enough bytes remain before dereferencing the IE header or its payload:
- pIE->element_id and pIE->length are read without checking that
i + sizeof(*pIE) <= ie_length, so a truncated IE at the end of the
buffer causes an OOB read.
- For WLAN_EID_VENDOR_SPECIFIC the code compares pIE->data + 12,
which requires pIE->length >= 16. For WLAN_EID_RSN it compares
pIE->data + 8, requiring pIE->length >= 12. Neither requirement
is checked.
Add the missing IE header and payload bounds checks and guard each
data access with an explicit pIE->length minimum, matching the
pattern established in update_beacon_info().
Fixes: 554c0a3abf21 ("staging: Add rtl8723bs sdio wifi driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Alexandru Hossu <hossu.alexandru@gmail.com>
Link: https://patch.msgid.link/20260522004531.1038924-7-hossu.alexandru@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The IE parsing loop in OnAssocRsp() advances by (pIE->length + 2) each
iteration but only guards on i < pkt_len. When a malicious AP sends an
AssocResponse whose last IE has only one byte remaining in the frame
(the element_id byte lands at pkt_len-1), the loop reads pIE->length
from pframe[pkt_len], which is one byte past the allocated receive buffer.
Additionally, even when the header bytes are in bounds, pIE->length
itself can extend the data window beyond pkt_len, silently passing a
truncated IE to the handler functions.
Add two guards at the top of the loop body:
1. Break if fewer than sizeof(*pIE) bytes remain (can't read header).
2. Break if the IE's declared data extends past pkt_len.
Fixes: 554c0a3abf21 ("staging: Add rtl8723bs sdio wifi driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Alexandru Hossu <hossu.alexandru@gmail.com>
Reviewed-by: Luka Gejak <luka.gejak@linux.dev>
Link: https://patch.msgid.link/20260522004531.1038924-6-hossu.alexandru@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
HT_caps_handler() iterates pIE->length bytes and writes into
HT_caps.u.HT_cap[], which is a fixed 26-byte array (sizeof struct
HT_caps_element). Because pIE->length is a raw u8 from an over-the-air
802.11 AssocResponse frame and is never validated, a malicious AP can
set it up to 255, causing up to 229 bytes of out-of-bounds writes into
adjacent fields of struct mlme_ext_info.
Truncate the iteration count to the size of HT_caps.u.HT_cap using
umin() so that data from a longer-than-expected IE is silently ignored
rather than written out of bounds, preserving interoperability with APs
that pad the element. An early return on oversized IEs was considered
but rejected: it would bypass the pmlmeinfo->HT_caps_enable = 1
assignment that precedes the loop, silently disabling HT mode for APs
that append extra bytes to the HT Capabilities IE.
Fixes: 554c0a3abf21 ("staging: Add rtl8723bs sdio wifi driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Alexandru Hossu <hossu.alexandru@gmail.com>
Reviewed-by: Luka Gejak <luka.gejak@linux.dev>
Link: https://patch.msgid.link/20260522004531.1038924-5-hossu.alexandru@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
supplicant_ie is a 256-byte array in struct security_priv. The WPA and
WPA2 IE copy paths use:
memcpy(padapter->securitypriv.supplicant_ie, &pwpa[0], wpa_ielen + 2);
where wpa_ielen is the raw IE length field (u8, 0-255). When a local user
supplies a connect request via nl80211 with a crafted WPA IE of length 255,
wpa_ielen + 2 equals 257, overflowing the 256-byte buffer by one byte into
the adjacent last_mic_err_time field.
rtw_parse_wpa_ie() does not prevent this: its length consistency check
compares *(wpa_ie+1) against (u8)(wpa_ie_len-2), which is (u8)(255) == 255
when wpa_ie_len = 257, so the check passes silently.
Add explicit bounds checks for both the WPA and WPA2 paths before the
memcpy, rejecting any IE whose total size (wpa_ielen + 2) exceeds the
supplicant_ie buffer.
Fixes: 554c0a3abf21 ("staging: Add rtl8723bs sdio wifi driver")
Cc: stable <stable@kernel.org>
Reviewed-by: Luka Gejak <luka.gejak@linux.dev>
Signed-off-by: Alexandru Hossu <hossu.alexandru@gmail.com>
Link: https://patch.msgid.link/20260522004531.1038924-4-hossu.alexandru@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
join_cmd_hdl()
Two IE parsing loops are missing the header bounds checks before they
dereference pIE->length:
- issue_assocreq() walks pmlmeinfo->network.ies to build the
association request. If the stored IE data ends with only an
element_id byte and no length byte, pIE->length is read one byte
past the end of the buffer.
- join_cmd_hdl() walks pnetwork->ies during station join and has
the same problem under the same conditions.
Both buffers are filled from AP beacon and probe-response frames, so a
malicious AP that sends a truncated final IE can trigger the issue.
Apply the two-guard pattern established in update_beacon_info():
1. Break if fewer than sizeof(*pIE) bytes remain.
2. Break if the IE's declared data extends past the buffer end.
Fixes: 554c0a3abf21 ("staging: Add rtl8723bs sdio wifi driver")
Cc: stable <stable@kernel.org>
Reviewed-by: Luka Gejak <luka.gejak@linux.dev>
Signed-off-by: Alexandru Hossu <hossu.alexandru@gmail.com>
Link: https://patch.msgid.link/20260522004531.1038924-3-hossu.alexandru@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The IE parsing loop in update_beacon_info() advances by
(pIE->length + 2) each iteration but only guards on i < len.
When a malicious AP sends a Beacon whose last IE has only one byte
remaining in the frame (the element_id byte lands at len-1), the loop
reads pIE->length from one byte past the allocated receive buffer.
Additionally, even when the header bytes are in bounds, pIE->length
itself can extend the data window beyond len, passing a truncated IE
to the handler functions.
Add two guards at the top of the loop body:
1. Break if fewer than sizeof(*pIE) bytes remain (can't read header).
2. Break if the IE's declared data extends past len.
Also replace i += (pIE->length + 2) with i += sizeof(*pIE) + pIE->length
for consistency with the sizeof(*pIE) guards added above.
Fixes: 554c0a3abf21 ("staging: Add rtl8723bs sdio wifi driver")
Cc: stable <stable@kernel.org>
Reviewed-by: Luka Gejak <luka.gejak@linux.dev>
Signed-off-by: Alexandru Hossu <hossu.alexandru@gmail.com>
Link: https://patch.msgid.link/20260522004531.1038924-2-hossu.alexandru@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
OnAuth() has two bugs in the shared-key authentication path.
When the Privacy bit is set, rtw_wep_decrypt() is called without
verifying that the frame is long enough to contain a valid WEP IV and
ICV. Inside rtw_wep_decrypt(), length is computed as:
length = len - WLAN_HDR_A3_LEN - iv_len
and then passed as (length - 4) to crc32_le(). If len is less than
WLAN_HDR_A3_LEN + iv_len + icv_len (32 bytes), length - 4 is negative
and, after the implicit cast to size_t, causes crc32_le() to read far
beyond the frame buffer. Add a minimum length check before accessing
the IV field and calling the decryption path.
When processing a seq=3 response, rtw_get_ie() stores the Challenge
Text IE length in ie_len, but the subsequent memcmp() always reads 128
bytes regardless of ie_len. IEEE 802.11 mandates a challenge text of
exactly 128 bytes; reject any IE whose length field differs, matching
the check already applied to OnAuthClient().
Fixes: 554c0a3abf21 ("staging: Add rtl8723bs sdio wifi driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Alexandru Hossu <hossu.alexandru@gmail.com>
Link: https://patch.msgid.link/20260522004605.1039209-1-hossu.alexandru@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
tsi148_probe() allocates a location monitor resource and links it into
tsi148_bridge->lm_resources. The probe error path frees this list, but
tsi148_remove() only frees the dma, slave and master resource lists, so
the location monitor resource is leaked on device unbind or module
unload.
Free the lm_resources list in tsi148_remove() as well, before
tsi148_bridge is freed.
Fixes: d22b8ed9a3b0 ("Staging: vme: add Tundra TSI148 VME-PCI Bridge driver")
Cc: stable <stable@kernel.org>
Cc: Martyn Welch <martyn@welchs.me.uk>
Assisted-by: Claude:claude-fable-5
Signed-off-by: Hao-Qun Huang <alvinhuang0603@gmail.com>
Link: https://patch.msgid.link/20260704065817.403111-2-alvinhuang0603@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
fake_init() allocates a location monitor resource and links it into
fake_bridge->lm_resources. The init error path frees this list, but
fake_exit() only frees the slave and master resource lists. Loading
and unloading the module therefore triggers a kmemleak warning:
unreferenced object 0xffff8b8b82aebe40 (size 64):
comm "init", pid 1, jiffies 4294894572
backtrace (crc c1e013ef):
kmemleak_alloc+0x4e/0x90
__kmalloc_cache_noprof+0x338/0x430
0xffffffffc0602246
do_one_initcall+0x4f/0x320
do_init_module+0x68/0x270
load_module+0x2a3b/0x2d90
Free the lm_resources list in fake_exit() as well, before fake_bridge
is freed.
Fixes: 658bcdae9c67 ("vme: Adding Fake VME driver")
Cc: stable <stable@kernel.org>
Cc: Martyn Welch <martyn@welchs.me.uk>
Assisted-by: Claude:claude-fable-5
Signed-off-by: Hao-Qun Huang <alvinhuang0603@gmail.com>
Link: https://patch.msgid.link/20260704065817.403111-1-alvinhuang0603@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
