# SPDX-License-Identifier: GPL-2.0

if LEDS_CLASS_MULTICOLOR

config LEDS_GROUP_MULTICOLOR
	tristate "LEDs group multi-color support"
	depends on OF
	help
	  This option enables support for monochrome LEDs that are grouped
	  into multicolor LEDs which is useful in the case where LEDs of
	  different colors are physically grouped in a single multi-color LED
	  and driven by a controller that doesn't have multi-color support.

	  To compile this driver as a module, choose M here: the module
	  will be called leds-group-multicolor.

config LEDS_KTD202X
	tristate "LED support for KTD202x Chips"
	depends on I2C
	select REGMAP_I2C
	help
	  This option enables support for the Kinetic KTD2026/KTD2027
	  RGB/White LED driver found in different BQ mobile phones.
	  It is a 3 or 4 channel LED driver programmed via an I2C interface.

	  To compile this driver as a module, choose M here: the module
	  will be called leds-ktd202x.

config LEDS_LP5812
	tristate "LED support for Texas Instruments LP5812"
	depends on I2C
	help
	  If you say Y here you get support for TI LP5812 LED driver.
	  The LP5812 is a 4x3 matrix RGB LED driver with autonomous
	  animation engine control.

	  To compile this driver as a module, choose M here: the
	  module will be called leds-lp5812.

	  If unsure, say N.

config LEDS_LP5860_CORE
	tristate "Core Driver for TI LP5860"
	depends on LEDS_CLASS
	depends on OF
	select REGMAP
	help
	  This option supports common operations for LP5860 devices.
	  The LP5860 is a LED matrix driver with 18 constant current
	  sinks and 11 scan switches for 198 LED dots. Each dot can be
	  controlled individually and supports 8/16-bit PWM dimming.
	  The chip supports individual LED open and short detection.

	  The device can be used with SPI or I2C bus.

config LEDS_LP5860_SPI
	tristate "LED Support for TI LP5860 SPI LED driver chip"
	depends on SPI
	depends on OF
	select LEDS_LP5860_CORE
	help
	  If you say yes here you get support for the Texas Instruments
	  LP5860 LED driver for SPI bus connections.

	  To compile this driver as a module, choose M here: the
	  module will be called leds-lp5860-spi.

config LEDS_NCP5623
	tristate "LED support for NCP5623"
	depends on I2C
	depends on OF
	help
	  This option enables support for ON semiconductor NCP5623
	  Triple Output I2C Controlled RGB LED Driver.

	  To compile this driver as a module, choose M here: the module
	  will be called leds-ncp5623.

config LEDS_PWM_MULTICOLOR
	tristate "PWM driven multi-color LED Support"
	depends on PWM
	help
	  This option enables support for PWM driven monochrome LEDs that are
	  grouped into multicolor LEDs.

	  To compile this driver as a module, choose M here: the module
	  will be called leds-pwm-multicolor.

config LEDS_QCOM_LPG
	tristate "LED support for Qualcomm LPG"
	depends on OF
	depends on PWM
	depends on QCOM_PBS || !QCOM_PBS
	depends on SPMI
	help
	  This option enables support for the Light Pulse Generator found in a
	  wide variety of Qualcomm PMICs. The LPG consists of a number of PWM
	  channels and typically a shared pattern lookup table and a current
	  sink, intended to drive RGB LEDs. Each channel can either be used as
	  a LED, grouped to represent a RGB LED or exposed as PWM channels.

	  If compiled as a module, the module will be named leds-qcom-lpg.

config LEDS_S2M_RGB
	tristate "Samsung S2M series PMICs RGB LED support"
	depends on LEDS_CLASS
	depends on MFD_SEC_CORE
	help
	  This option enables support for the S2MU005 RGB LEDs. These devices
	  have three LED channels, with 8-bit brightness control for each
	  channel. The S2MU005 is usually found in mobile phones as status
	  indicators.

config LEDS_MT6370_RGB
	tristate "LED Support for MediaTek MT6370 PMIC"
	depends on MFD_MT6370
	select LINEAR_RANGES
	help
	  Say Y here to enable support for MT6370_RGB LED device.
	  In MT6370, there are four channel current-sink LED drivers that
	  support hardware pattern for constant current, PWM, and breath mode.
	  Isink4 channel can also be used as a CHG_VIN power good indicator.

	  This driver can also be built as a module. If so, the module
	  will be called "leds-mt6370-rgb".

endif # LEDS_CLASS_MULTICOLOR