kernel/git/stable/linux-stable.git/drivers/scsi, branch linux-3.12.y

scsi: sd: Fix capacity calculation with 32-bit sector_t

2017-04-28T17:30:45+00:00

commit 7c856152cb92f8eee2df29ef325a1b1f43161aff upstream. We previously made sure that the reported disk capacity was less than 0xffffffff blocks when the kernel was not compiled with large sector_t support (CONFIG_LBDAF). However, this check assumed that the capacity was reported in units of 512 bytes. Add a sanity check function to ensure that we only enable disks if the entire reported capacity can be expressed in terms of sector_t. Reported-by: Steve Magnani Cc: Bart Van Assche Reviewed-by: Bart Van Assche Signed-off-by: Martin K. Petersen Signed-off-by: Jiri Slaby

scsi: sr: Sanity check returned mode data

2017-04-28T17:30:44+00:00

commit a00a7862513089f17209b732f230922f1942e0b9 upstream. Kefeng Wang discovered that old versions of the QEMU CD driver would return mangled mode data causing us to walk off the end of the buffer in an attempt to parse it. Sanity check the returned mode sense data. Reported-by: Kefeng Wang Tested-by: Kefeng Wang Signed-off-by: Martin K. Petersen Signed-off-by: Jiri Slaby

scsi: libsas: fix ata xfer length

2017-04-07T12:59:29+00:00

commit 9702c67c6066f583b629cf037d2056245bb7a8e6 upstream. The total ata xfer length may not be calculated properly, in that we do not use the proper method to get an sg element dma length. According to the code comment, sg_dma_len() should be used after dma_map_sg() is called. This issue was found by turning on the SMMUv3 in front of the hisi_sas controller in hip07. Multiple sg elements were being combined into a single element, but the original first element length was being use as the total xfer length. Fixes: ff2aeb1eb64c8a4770a6 ("libata: convert to chained sg") Signed-off-by: John Garry Signed-off-by: Martin K. Petersen Signed-off-by: Jiri Slaby

scsi: mpt3sas: fix hang on ata passthrough commands

2017-04-07T12:33:55+00:00

commit ffb58456589443ca572221fabbdef3db8483a779 upstream. mpt3sas has a firmware failure where it can only handle one pass through ATA command at a time. If another comes in, contrary to the SAT standard, it will hang until the first one completes (causing long commands like secure erase to timeout). The original fix was to block the device when an ATA command came in, but this caused a regression with commit 669f044170d8933c3d66d231b69ea97cb8447338 Author: Bart Van Assche Date: Tue Nov 22 16:17:13 2016 -0800 scsi: srp_transport: Move queuecommand() wait code to SCSI core So fix the original fix of the secure erase timeout by properly returning SAM_STAT_BUSY like the SAT recommends. The original patch also had a concurrency problem since scsih_qcmd is lockless at that point (this is fixed by using atomic bitops to set and test the flag). [mkp: addressed feedback wrt. test_bit and fixed whitespace] Fixes: 18f6084a989ba1b (mpt3sas: Fix secure erase premature termination) Signed-off-by: James Bottomley Acked-by: Sreekanth Reddy Reviewed-by: Christoph Hellwig Reported-by: Ingo Molnar Tested-by: Ingo Molnar Signed-off-by: Martin K. Petersen Cc: Joe Korty Signed-off-by: Jiri Slaby

scsi: lpfc: Add shutdown method for kexec

2017-04-07T07:17:51+00:00

commit 85e8a23936ab3442de0c42da97d53b29f004ece1 upstream. We see lpfc devices regularly fail during kexec. Fix this by adding a shutdown method which mirrors the remove method. Signed-off-by: Anton Blanchard Reviewed-by: Mauricio Faria de Oliveira Tested-by: Mauricio Faria de Oliveira Signed-off-by: Martin K. Petersen Signed-off-by: Jiri Slaby

mvsas: fix misleading indentation

2017-03-28T13:49:18+00:00

commit 7789cd39274c51bf475411fe22a8ee7255082809 upstream. Fix a smatch warning: drivers/scsi/mvsas/mv_sas.c:740 mvs_task_prep() warn: curly braces intended? The code is correct, the indention is misleading. When the device is not ready we want to return SAS_PHY_DOWN. But current indentation makes it look like we only do so in the else branch of if (mvi_dev). Signed-off-by: Luis de Bethencourt Reviewed-by: Johannes Thumshirn Signed-off-by: Martin K. Petersen Signed-off-by: Jiri Slaby

scsi: lpfc: Correct WQ creation for pagesize

2017-03-13T20:40:41+00:00

commit 8ea73db486cda442f0671f4bc9c03a76be398a28 upstream. Correct WQ creation for pagesize The driver was calculating the adapter command pagesize indicator from the system pagesize. However, the buffers the driver allocates are only one size (SLI4_PAGE_SIZE), so no calculation was necessary. Signed-off-by: Dick Kennedy Signed-off-by: James Smart Reviewed-by: Hannes Reinecke Reviewed-by: Johannes Thumshirn Reviewed-by: Christoph Hellwig Signed-off-by: Martin K. Petersen Cc: Mauricio Faria de Oliveira Signed-off-by: Jiri Slaby

sd: get disk reference in sd_check_events()

2017-03-13T20:40:28+00:00

commit eb72d0bb84eee5d0dc3044fd17b75e7101dabb57 upstream. sd_check_events() is called asynchronously, and might race with device removal. So always take a disk reference when processing the event to avoid the device being removed while the event is processed. Signed-off-by: Hannes Reinecke Reviewed-by: Ewan D. Milne Reviewed-by: Bart Van Assche Signed-off-by: Martin K. Petersen Cc: Jinpu Wang Signed-off-by: Jiri Slaby

scsi: aacraid: Reorder Adapter status check

2017-03-13T20:40:27+00:00

commit c421530bf848604e97d0785a03b3fe2c62775083 upstream. The driver currently checks the SELF_TEST_FAILED first and then KERNEL_PANIC next. Under error conditions(boot code failure) both SELF_TEST_FAILED and KERNEL_PANIC can be set at the same time. The driver has the capability to reset the controller on an KERNEL_PANIC, but not on SELF_TEST_FAILED. Fixed by first checking KERNEL_PANIC and then the others. Fixes: e8b12f0fb835223752 ([SCSI] aacraid: Add new code for PMC-Sierra's SRC base controller family) Signed-off-by: Raghava Aditya Renukunta Reviewed-by: David Carroll Reviewed-by: Johannes Thumshirn Signed-off-by: Martin K. Petersen Signed-off-by: Jiri Slaby

scsi: storvsc: properly set residual data length on errors

2017-03-13T20:40:27+00:00

commit 40630f462824ee24bc00d692865c86c3828094e0 upstream. On I/O errors, the Windows driver doesn't set data_transfer_length on error conditions other than SRB_STATUS_DATA_OVERRUN. In these cases we need to set data_transfer_length to 0, indicating there is no data transferred. On SRB_STATUS_DATA_OVERRUN, data_transfer_length is set by the Windows driver to the actual data transferred. Reported-by: Shiva Krishna Signed-off-by: Long Li Reviewed-by: K. Y. Srinivasan Signed-off-by: K. Y. Srinivasan Signed-off-by: Martin K. Petersen Signed-off-by: Jiri Slaby