kernel/git/stable/linux-stable.git/drivers/usb/Kconfig, branch linux-2.6.22.y

[S390] Kconfig: menus with depends on HAS_IOMEM.

2007-05-10T13:46:07+00:00

Add "depends on HAS_IOMEM" to a number of menus to make them disappear for s390 which does not have I/O memory. Signed-off-by: Martin Schwidefsky

Move USB network drivers to drivers/net/usb.

2007-05-10T01:31:55+00:00

It is preferable to group drivers by usage (net, scsi, ATA, ...) than by bus. When reviewing drivers, the [PCI|USB|PCMCIA|...] maintainer is probably less qualified on networking issues than a networking maintainer. Also, from a practical standpoint, chips often appear on multiple buses, which is why we do not put drivers into drivers/pci/net. Signed-off-by: Greg Kroah-Hartman Signed-off-by: Jeff Garzik

Input: move USB miscellaneous devices under drivers/input/misc

2007-05-08T05:41:29+00:00

This will allow concentrating all input devices in one place in {menu|x|q}config. Signed-off-by: Dmitry Torokhov Acked-by: Greg Kroah-Hartman

[ARM] 3963/1: AT91: Update configuration files

2006-12-01T16:56:43+00:00

A number of configuration file changes. These are mainly to replace references to ARCH_AT91RM9200 and ARCH_AT91SAM9261 with the common/generic ARCH_AT91. That way we don't need to mention every specific AT91 processor explicitly. Also adds the configuration option for AT91SAM9260-EK and AT91SAM9261-EK boards. Signed-off-by: Andrew Victor Signed-off-by: Russell King

USB OHCI controller support for PNX4008

2006-09-27T18:58:48+00:00

inlined is the patch that adds basic support for USB OHCI controller support for PNX4008 Philips PNX4008 ARM board. Due to HW design, it depends on I2C driver for PNX4008 which I've recetnly posted to LKML and i2c at lm-sensors. Signed-off-by: Vitaly Wool Cc: David Brownell Signed-off-by: Greg Kroah-Hartman

USB: AT91 OHCI updates, mostly power management

2006-08-02T23:41:41+00:00

OHCI updates for AT91 series processors: - Get ready for at91sam926x processors (ARMv5tej not ARMv4t) - Suspend/resume support now behaves properly - In "standby" mode, OHCI can be a source of system wakeup events (remote wakeup, device connect/disconnect, etc) And minor cleanups. Signed-off-by: David Brownell Signed-off-by: Andrew Victor Signed-off-by: Greg Kroah-Hartman

[PATCH] USB: ohci bits for the cirrus ep93xx

2006-07-12T23:03:20+00:00

This patch adds OHCI glue bits for the USB host interface in the Cirrus ep93xx (arm920t) CPU. Signed-off-by: Lennert Buytenhek Acked-by: David Brownell Signed-off-by: Greg Kroah-Hartman

V4L/DVB (3599a): Move drivers/usb/media to drivers/media/video

2006-03-25T12:29:04+00:00

Because of historic reasons, there are two separate directories with V4L stuff. Most drivers are located at driver/media/video. However, some code for USB Webcams were inserted under drivers/usb/media. This makes difficult for module authors to know were things should be. Also, makes Kconfig menu confusing for normal users. This patch moves all V4L content under drivers/usb/media to drivers/media/video, and fixes Kconfig/Makefile entries. Signed-off-by: Greg Kroah-Hartman Signed-off-by: Mauro Carvalho Chehab

[PATCH] USB: add support for OCHI on AT91rm9200

2006-03-20T22:49:55+00:00

This adds support for OHCI on AT91rm9200 based boards. Possibly of interest here is the way this uses to gate clocks on/off during system pm state transitions. That's typical for non-PCI systems. Some can go further; Mini-A host side connectors enable ID-pin sensing. From: Andrew Victor Signed-off-by: David Brownell Signed-off-by: Greg Kroah-Hartman

[PATCH] USB: EHCI for AU1200

2006-03-20T22:49:55+00:00

ALCHEMY: Add EHCI support for AU1200 Updated by removing the OHCI support Signed-off-by: Jordan Crouse Signed-off-by: David Brownell Signed-off-by: Greg Kroah-Hartman