kernel/git/stable/linux-stable.git/drivers/video/backlight, branch linux-5.13.y

backlight: pwm_bl: Improve bootloader/kernel device handover

2021-09-15T08:00:59+00:00

commit 79fad92f2e596f5a8dd085788a24f540263ef887 upstream. Currently there are (at least) two problems in the way pwm_bl starts managing the enable_gpio pin. Both occur when the backlight is initially off and the driver finds the pin not already in output mode and, as a result, unconditionally switches it to output-mode and asserts the signal. Problem 1: This could cause the backlight to flicker since, at this stage in driver initialisation, we have no idea what the PWM and regulator are doing (an unconfigured PWM could easily "rest" at 100% duty cycle). Problem 2: This will cause us not to correctly honour the post_pwm_on_delay (which also risks flickers). Fix this by moving the code to configure the GPIO output mode until after we have examines the handover state. That allows us to initialize enable_gpio to off if the backlight is currently off and on if the backlight is on. Cc: stable@vger.kernel.org Reported-by: Marek Vasut Signed-off-by: Daniel Thompson Acked-by: Marek Vasut Tested-by: Marek Vasut Signed-off-by: Lee Jones Signed-off-by: Greg Kroah-Hartman

backlight: lm3630a: Fix return code of .update_status() callback

2021-07-20T14:00:21+00:00

[ Upstream commit b9481a667a90ec739995e85f91f3672ca44d6ffa ] According to .update_status() is supposed to return 0 on success and a negative error code otherwise. Adapt lm3630a_bank_a_update_status() and lm3630a_bank_b_update_status() to actually do it. While touching that also add the error code to the failure message. Signed-off-by: Uwe Kleine-König Reviewed-by: Daniel Thompson Signed-off-by: Lee Jones Signed-off-by: Sasha Levin

backlight: lm3630a_bl: Put fwnode in error case during ->probe()

2021-07-14T15:07:30+00:00

[ Upstream commit 6d1c32dbedd7d7e7372aa38033ec8782c39f6379 ] device_for_each_child_node() bumps a reference counting of a returned variable. We have to balance it whenever we return to the caller. Cc: Brian Masney Cc: Dan Murphy Fixes: 8fbce8efe15cd ("backlight: lm3630a: Add firmware node support") Signed-off-by: Andy Shevchenko Reviewed-by: Brian Masney Reviewed-by: Daniel Thompson Signed-off-by: Lee Jones Signed-off-by: Sasha Levin

backlight: journada720: Fix Wmisleading-indentation warning

2021-03-23T09:42:55+00:00

With gcc-11, we get a warning about code that looks correct but badly indented: drivers/video/backlight/jornada720_bl.c: In function ‘jornada_bl_update_status’: drivers/video/backlight/jornada720_bl.c:66:11: error: this ‘else’ clause does not guard... [-Werror=misleading-indentation] 66 | } else /* turn on backlight */ | ^~~~ Change the formatting according to our normal conventions. Fixes: 13a7b5dc0d17 ("backlight: Adds HP Jornada 700 series backlight driver") Signed-off-by: Arnd Bergmann Reviewed-by: Daniel Thompson Signed-off-by: Lee Jones

backlight: qcom-wled: Correct the sync_toggle sequence

2021-03-23T09:40:25+00:00

As per the current implementation, after FSC (Full Scale Current) and brightness update the sync bits are set-then-cleared. But, the FSC and brightness sync takes place when the sync bits are set (e.g. on a rising edge). So the hardware team recommends a clear-then-set approach in order to guarantee such a transition regardless of the previous register state. Signed-off-by: Kiran Gunda Reviewed-by: Daniel Thompson Signed-off-by: Lee Jones

backlight: qcom-wled: Fix FSC update issue for WLED5

2021-03-22T17:33:42+00:00

Currently, for WLED5, the FSC (Full scale current) setting is not updated properly due to driver toggling the wrong register after an FSC update. On WLED5 we should only toggle the MOD_SYNC bit after a brightness update. For an FSC update we need to toggle the SYNC bits instead. Fix it by adopting the common wled3_sync_toggle() for WLED5 and introducing new code to the brightness update path to compensate. Signed-off-by: Kiran Gunda Reviewed-by: Daniel Thompson Signed-off-by: Lee Jones

backlight: ktd253: Support KTD259

2021-03-22T14:29:22+00:00

The KTD259 works just like KTD253 so add this compatible to the driver. Signed-off-by: Linus Walleij Reviewed-by: Daniel Thompson Signed-off-by: Lee Jones

backlight: qcom-wled: Use sink_addr for sync toggle

2021-03-22T14:29:03+00:00

WLED3_SINK_REG_SYNC is, as the name implies, a sink register offset. Therefore, use the sink address as base instead of the ctrl address. This fixes the sync toggle on wled4, which can be observed by the fact that adjusting brightness now works. It has no effect on wled3 because sink and ctrl base addresses are the same. This allows adjusting the brightness without having to disable then reenable the module. Signed-off-by: Obeida Shamoun Signed-off-by: Konrad Dybcio Signed-off-by: Marijn Suijten Reviewed-by: Daniel Thompson Acked-by: Kiran Gunda Signed-off-by: Lee Jones

Merge tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm

2021-02-22T22:27:07+00:00

Pull ARM updates from Russell King: - Generalise byte swapping assembly - Update debug addresses for STI - Validate start of physical memory with DTB - Do not clear SCTLR.nTLSMD in decompressor - amba/locomo/sa1111 devices remove method return type is void - address markers for KASAN in page table dump * tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm: ARM: 9065/1: OABI compat: fix build when EPOLL is not enabled ARM: 9055/1: mailbox: arm_mhuv2: make remove callback return void amba: Make use of bus_type functions amba: Make the remove callback return void vfio: platform: simplify device removal amba: reorder functions amba: Fix resource leak for drivers without .remove ARM: 9054/1: arch/arm/mm/mmu.c: Remove duplicate header ARM: 9053/1: arm/mm/ptdump:Add address markers for KASAN regions ARM: 9051/1: vdso: remove unneded extra-y addition ARM: 9050/1: Kconfig: Select ARCH_HAVE_NMI_SAFE_CMPXCHG where possible ARM: 9049/1: locomo: make locomo bus's remove callback return void ARM: 9048/1: sa1111: make sa1111 bus's remove callback return void ARM: 9047/1: smp: remove unused variable ARM: 9046/1: decompressor: Do not clear SCTLR.nTLSMD for ARMv7+ cores ARM: 9045/1: uncompress: Validate start of physical memory against passed DTB ARM: 9042/1: debug: no uncompress debugging while semihosting ARM: 9041/1: sti LL_UART: add STiH418 SBC UART0 support ARM: 9040/1: use DEBUG_UART_PHYS and DEBUG_UART_VIRT for sti LL_UART ARM: 9039/1: assembler: generalize byte swapping macro into rev_l

backlight/video: Use Platform getter/setter functions

2021-02-12T10:01:45+00:00

Use getter and setter functions, for platform_device structures and a spi_device structure. Signed-off-by: Julia Lawall Acked-by: Daniel Vetter Signed-off-by: Lee Jones