| Age | Commit message (Collapse) | Author |
|---|
|
Fix the wrong connection for the qdss replicator device.
Fixes: 4f791e008807a ("arm64: dts: qcom: monaco: Add CTCU and ETR nodes")
Signed-off-by: Jie Gan <jie.gan@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260428-fix-monaco-coresight-dt-v2-1-2293259bbd10@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
The GX GDSC control is handled through a dedicated clock controller,
and the enable/disable sequencing depends on correct rail voting.
The driver votes for the GX/GMxC rails and CX GDSC before toggling
the GX GDSC. Currently, during GMU runtime PM resume, rails remain
enabled due to upstream votes propagated via RPM-enabled devlinks
and explicit pm_runtime votes on GX GDSC.
This is not an expected behaviour of IFPC(Inter Frame Power Collapse)
requirements of GPU as GMU firmware is expected to control these rails,
except during the GPU/GMU recovery via the OS and that is where the GX
GDSC should be voting for the rails (GX/GMxC and CX GDSC) before
toggling the GX GDSC.
Thus, disable runtime PM after successfully registering the clock
controller.
Signed-off-by: Taniya Das <taniya.das@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260427-gfx-clk-fixes-v2-4-797e54b3d464@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
When the clock controller is probed with 'use_rpm' enabled, the
runtime PM reference is currently released using pm_runtime_put(),
which may return before the runtime suspend has completed. When the
clock controller device is registered through this function, calling
pm_runtime_disable() immediately after pm_runtime_put() prevents
the runtime suspend from completing, leaving the clock controller
active and the HW rails in the ON state.
Use pm_runtime_put_sync() instead to ensure the runtime PM “putV
completes synchronously during probe. This does not have any functional
impact, but it guarantees that the device is fully runtime-suspended
before returning.
Signed-off-by: Taniya Das <taniya.das@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260427-gfx-clk-fixes-v2-3-797e54b3d464@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
The GX GDSC represents a special GPU power domain that must not be
disabled during normal runtime PM flows. As per the GMU architecture,
GX GDSC should only be force-disabled during GMU/GPU recovery, where the
OS explicitly resets the GX power domain.
However, when managed by the generic GDSC runtime PM path, GX GDSC may be
disabled during GMU runtime suspend, resulting in warnings such as:
gx_clkctl_gx_gdsc status stuck at 'on'
and failures in gdsc_toggle_logic() during rpm suspend.
Use the newly added custom disable callback for gx_gdsc to ensure the
GDSC is toggled only in recovery scenarios, while preventing unintended
disable attempts during normal GMU runtime PM operations.
Reported-by: Pengyu Luo <mitltlatltl@gmail.com>
Closes: https://lore.kernel.org/all/CAH2e8h4Vp9fJYAUUbOmoHSKB25wakPBvmpwa62BTRqgRQbMWuw@mail.gmail.com/
Reported-by: Alexander Koskovich <akoskovich@pm.me>
Closes: https://lore.kernel.org/all/gwVAH2mJerU4dBInw8pKmOs5aQK55Q7W6q_UQAlLFCsEgX6eyvSgXAWbNNMqAX4WmPlYCKUSMhfkr5Jry4Ps5EqnxYZqEEDd3Whwv7ZXGlc=@pm.me/
Fixes: 5af11acae660 ("clk: qcom: Add a driver for SM8750 GPU clocks")
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Taniya Das <taniya.das@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260427-gfx-clk-fixes-v2-2-797e54b3d464@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
The GX GDSC is a special power domain that should only be disabled
by OS during GMU recovery. In all other scenarios, the GMU firmware
is responsible for handling its disable sequence, and OS must not
interfere.
During the resume_noirq() phase of system resume, the GenPD framework
enables all power domains and later disables them in the complete()
phase if there are no active votes from OS. This behavior can
incorrectly disable the GX GDSC while the GMU firmware is still using
it.
To prevent this, implement a custom disable callback for GX GDSC that
relies on GenPD’s synced_poweroff flag. The GMU driver sets this flag
only during recovery, allowing OS to explicitly disable GX GDSC in
hardware in that case. In all other situations, the disable callback
will avoid touching GX GDSC hardware.
Signed-off-by: Jagadeesh Kona <jagadeesh.kona@oss.qualcomm.com>
Signed-off-by: Taniya Das <taniya.das@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260427-gfx-clk-fixes-v2-1-797e54b3d464@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Enable CONFIG_SND_SOC_DMIC as a module in the arm64 defconfig
to support digital microphone functionality on Qualcomm's
Monaco and Lemans platforms.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Ravi Hothi <ravi.hothi@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260427094131.607583-1-ravi.hothi@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Add support for building an EL2 combined DTB for the talos-evk
in the Qualcomm DTS Makefile.
The new talos-evk-el2.dtb is generated by combining the base
talos-evk.dtb with the talos-el2.dtbo overlay, enabling EL2-specific
configurations required by the platform.
Signed-off-by: Xin Liu <xin.liu@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260427082325.1895450-1-xin.liu@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Configure and enable the node for IPA which enables mobile data on this
device.
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260410-milos-ipa-v2-2-c699b6b8cf27@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Add the description of the IPA block in the Milos SoC.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Link: https://lore.kernel.org/r/20260410-milos-ipa-v2-1-c699b6b8cf27@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
There are 2 possible scenarios where the cgroup_taskset structure
passed into the cgroup can_attach() and attach() methods can contain
task migration data with multiple source cpusets.
- A multithread application with threads in different cpusets is
fully migrated into a new cpuset.
- Disabling v2 cpuset controller will move all the tasks in child
cpusets to the parent cpuset.
The current cpuset_can_attach() and cpuset_attach() functions still
expect task migration is from one source cpuset to one destination
cpuset.
Fix that by tracking the set of source (old) cpusets in singly linked
lists. The list will be iterated when necessary to properly update
internal data.
To ensure proper DL tasks accounting, the nr_migrate_dl_tasks in both
the source and destination cpusets are decremented/incremented with
their values added to nr_deadline_tasks when the migration is successful.
The setting of the global attach_ctx.cpus_updated and
attach_ctx.mems_updated flags are also moved from cpuset_attach()
to cpuset_can_attach() as the correct source cpuset can no longer be
determined in cpuset_attach() and cpuset states will not be changed
between cpuset_attach() and cpuset_can_attach() with an earlier patch.
Signed-off-by: Waiman Long <longman@redhat.com>
Reviewed-by: Ridong Chen <ridong.chen@linux.dev>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
cpuset_attach_task()
The cpuset_attach_task() was introduced in commit 42a11bf5c543
("cgroup/cpuset: Make cpuset_fork() handle CLONE_INTO_CGROUP properly")
to enable the CLONE_INTO_CGROUP flag of clone(2) to behave more like
moving a task from one cpuset into another one. That commits didn't
move the mpol_rebind_mm() and cpuset_migrate_mm() calls for group leader
into cpuset_attach_task().
When the CLONE_INTO_CGROUP flag is used without CLONE_THREAD, the new
task is its own group leader. So it is still not equivalent to moving
task between cpusets in this case. Make CLONE_INTO_CGROUP behaves
more close to cpuset_attach() by moving the mpol_rebind_mm() and
cpuset_migrate_mm() calls inside cpuset_attach_task().
Also move the stack local cpus_updated, mems_updated and queue_task_work
flags into attach_ctx so that these flags can be accessed inside and
outside of cpuset_attach_task(). The cpuset_fork() function is updated
to set up these flags and do memory migration if necessary.
Reviewed-by: Ridong Chen <ridong.chen@linux.dev>
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
There are two possible ways that migration of tasks from multiple source
cpusets to a target cpuset can happen. Either a multithread application
with threads in different cpusets is wholely migrated to a new cpuset
or disabling of v2 cpuset controller will move all the tasks in child
cpusets to the parent cpuset.
In the former case, it is the mm setting of the group leader that
really matters. So attach_ctx.old_cs should track the oldcs of the
thread leader. In the latter case, effective_mems of child cpusets
must always be a subset of the parent. So no real page migration
will not be necessary no matter which child cpuset is selected as
attach_ctx.old_cs.
IOW, attach_ctx.old_cs should be updated to match the latest task
group leader in cpuset_can_attach(), but fall back to that of the first
task if there is no group leader in the taskset.
Suggested-by: Ridong Chen <ridong.chen@linux.dev>
Signed-off-by: Waiman Long <longman@redhat.com>
Reviewed-by: Ridong Chen <ridong.chen@linux.dev>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Expand the scope of cpuset_can_attach_check() by including the setting
of setsched flag inside cpuset_can_attach_check() with the new @oldcs
and @psetsched argument. As cpuset_can_attach_check() is also called
from cpuset_can_fork(), set the new arguments to NULL from that caller.
Signed-off-by: Waiman Long <longman@redhat.com>
Reviewed-by: Ridong Chen <ridong.chen@linux.dev>
Signed-off-by: Michal Koutný <mkoutny@suse.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Extract the DL bandwidth allocation code in cpuset_attach() to a new
cpuset_reserve_dl_bw() helper to simplify code.
No functional change is expected.
Signed-off-by: Waiman Long <longman@redhat.com>
Reviewed-by: Ridong Chen <ridong.chen@linux.dev>
Reviewed-by: Gregory Price <gourry@gourry.net>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Put the task attach related cpuset_attach_old_cs and
cpuset_attach_nodemask_to static variables into the new attach_ctx
structure to improve readability and ease maintanence.
No functional change is expected.
Suggested-by: Ridong Chen <ridong.chen@linux.dev>
Signed-off-by: Waiman Long <longman@redhat.com>
Reviewed-by: Ridong Chen <ridong.chen@linux.dev>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Commit e44193d39e8d ("cpuset: let hotplug propagation work wait for
task attaching") was introduced to let hotplug operation to wait
until the completion of task attach operation. However, it is still
possible that the states of the source or destination cpuset can
be changed between the cpuset_can_attach() call and the subsequent
cpuset_attach()/cpuset_cancel_attach() call.
As a result, data gathered during cpuset_can_attach() cannot be reliably
used in the subsequent cpuset_attach()/cpuset_cancel_attach()
call at all. Make the task attach operation more robust
and allow the sharing of data between cpuset_can_attach() and
cpuset_attach()/cpuset_cancel_attach() by making cpuset_write_resmask()
and cpuset_partition_write() wait for the completion of task attach
as well.
Ideally, an ongoing task attach operation should block any cpuset write
operation that can change its internal state until the operation is
completed. However, the attach_in_progress flag is currently per cpuset
and only the destination cpuset will have this flag set. The flag is not
set in the source cpuset where the tasks will be moved from. Even if we
extend the scope to include the source cpuset, it will not block cpuset
operation that changes the state of one of its ancestor cpuset which may
indirectly impact the state of the source or destination cpuset. It may
be too costly to set the flag for the whole subtree, it is far easier
to just make the flag global and block all the cpuset write operation
whenever a task attach operation is in progress.
Make that change by creating a new cpuset attach context (attach_ctx)
structure to hold the global in_progress flag and use it for blocking
cpuset write operation if a cpuset attach operation is in progress. Also
add a new wait_attach_done_lock() helper to do the waiting for an
ongoing attach operation and acquire the cpuset_mutex.
The comments about validate_change() are no longer valid as it won't
be called at all if an attach operation is in progress. So the comments
can be removed.
The per-cpuset attach_in_progress flag is also currently used in
partition_is_populated() and cpuset_is_populated() to determine if
an empty cpuset will have incoming task. This check will no longer be
needed as this function will not be called when there is a task attach
in progress. So the flag check is now removed.
Reviewed-by: Ridong Chen <ridong.chen@linux.dev>
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
cpuset_update_tasks_nodemask() and cpuset_attach()
Whenever memory node mask is changed, there are 4 places where the node
mask has to be updated or used.
1) task's node mask via cpuset_change_task_nodemask()
2) memory policy binding via mpol_rebind_mm()
3) if memory migration is enabled, migrate from old_mems_allowed to
the new node mask via cpuset_migrate_mm().
4) setting old_mems_allowed
These memory actions are done in cpuset_update_tasks_nodemask() and
cpuset_attach(). However there are inconsistencies in what node masks
are being used in these 2 functions.
In cpuset_update_tasks_nodemask(),
- cpuset_change_task_nodemask(): guarantee_online_mems()
- mpol_rebind_mm(): mems_allowed
- cpuset_migrate_mm(): guarantee_online_mems()
- old_mems_allowed: guarantee_online_mems()
In cpuset_attach(),
- cpuset_change_task_nodemask(): guarantee_online_mems()
- mpol_rebind_mm(): effective_mems
- cpuset_migrate_mm(): effective_mems
- old_mems_allowed: effective_mems
These inconsistencies dates back to quite a long time ago and it is
hard to say what should be the correct values.
The guarantee_online_mems() function returns a node mask from current or
an ancestor cpuset that is a subset of node_states[N_MEMORY]. Nodes in
node_states[N_MEMORY] are all online, i.e. in node_states[N_ONLINE].
However, node in node_states[N_ONLINE] may not have memory. So
node_states[N_MEMORY] should be a subset of node_states[N_ONLINE].
The guarantee_online_mems() function should mostly be useful for v1
where mems_allowed is the same as effective_mems. With v2, the memory
nodes in effective_mems should be a subset of node_states[N_MEMORY]
except when a memory hot-unplug operation is in progress and a memory
node is removed from node_states[N_MEMORY] but not yet reflected in
the effective_mems's as cpuset_handle_hotplug() has not been called
from cpuset_track_online_nodes().
Let use the following setup for both of them and make them consistent.
- cpuset_change_task_nodemask(): guarantee_online_mems()
- mpol_rebind_mm(): effective_mems
- cpuset_migrate_mm(): guarantee_online_mems()
- old_mems_allowed: guarantee_online_mems()
So for v2, it is effectively all effective_mems most of the time. For
v1, mpol_rebind_mm() uses mems_allowed which may differ from what
guarantee_online_mems() returns, but it conforms to what the cpuset v1
documentation says with respect to setting memory policy.
Signed-off-by: Waiman Long <longman@redhat.com>
Reviewed-by: Ridong Chen <ridong.chen@linux.dev>
Reviewed-by: Gregory Price <gourry@gourry.net>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
The nr_deadline_tasks variable in the cpuset structure was introduced by
commit 6c24849f5515 ("sched/cpuset: Keep track of SCHED_DEADLINE task
in cpusets"). It is reported by sashiko [1] that nr_deadline_tasks
can currently be modified by inc_dl_tasks_cs() under rq->lock and
by cpuset_attach() under cpuset_mutex. So if both updates happen
simultaneously, the nr_deadline_tasks variable can be corrupted leading
to incorrect operations down the road.
Fix that by changing its type to atomic_t so that nr_deadline_tasks
are always atomically updated. This fix patch is a low hanging fruit.
It can handle some of the races between a concurrent sched_setscheduler()
and cpuset_can_attach()/cpuset_attach() calls, but not all of them like
the other issue raised by sashiko [2]. This will be handled hopefully
in a future follow up patch.
[1] https://sashiko.dev/#/patchset/20260626181923.133658-1-longman%40redhat.com
[2] https://sashiko.dev/#/patchset/20260630033344.352702-1-longman%40redhat.com
Fixes: 6c24849f5515 ("sched/cpuset: Keep track of SCHED_DEADLINE task in cpusets")
Reviewed-by: Ridong Chen <ridong.chen@linux.dev>
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
When growing a provided-buffer bundle, the old cached iovec is freed
before the new buffers have all been validated. If validation fails, the
request still points at the freed iovec, which can be freed again during
completion cleanup.
Fix this by deferring the free of the old cached iovec until validation
has succeeded. On failure, free the newly allocated iovec and leave the
request pointing at the original one.
Fixes: 46800585ae04 ("io_uring/kbuf: validate ring provided buffer addresses with access_ok()")
Signed-off-by: Hao-Yu Yang <naup96721@gmail.com>
Link: https://patch.msgid.link/20260706183304.919275-1-naup96721@gmail.com
Suggested-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
If mkdir_mondata_all() or a subsequent call in rdt_get_tree() fails, the
mon_data structures allocated by mon_get_kn_priv() are leaked.
Add mon_put_kn_priv() to the out_mongrp error path to free the mon_data
structures.
Fixes: 2a6566038544 ("x86/resctrl: Expand the width of domid by replacing mon_data_bits")
Closes: https://lore.kernel.org/lkml/5d38c1fb-8f91-472b-8897-24b2f50c772b@intel.com/
Reported-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Chen Yu <yu.c.chen@intel.com>
Reviewed-by: Ben Horgan <ben.horgan@arm.com>
Cc: <stable@kernel.org>
Link: https://patch.msgid.link/433623b7e3316ffd52323255d1aa4f156ad97cb1.1783377598.git.reinette.chatre@intel.com
|
|
A NULL pointer dereference issue is noticed in riscv's
machine_kexec_prepare(), where image->segment[i].buf might be NULL and
copied unchecked.
The NULL buf comes from ima_add_kexec_buffer(), where kbuf is added by
kexec_add_buffer(), but kbuf.buffer is NULL, then it is copied without
a check in machine_kexec_prepare():
kexec_file_load
-> kimage_file_alloc_init()
-> kimage_file_prepare_segments()
-> ima_add_kexec_buffer()
-> kexec_add_buffer()
-> machine_kexec_prepare()
-> memcpy()
Address this by adding a check before the data copy attempt.
Fixes: b7fb4d78a6ad ("RISC-V: use memcpy for kexec_file mode")
Cc: stable@vger.kernel.org
Closes: https://lore.kernel.org/kexec/CAO7dBbVftLUhd2qrh7hmijTB3PEPfZAhykCGqEfrPoOcSrrj-w@mail.gmail.com/
Acked-by: Baoquan He <bhe@redhat.com>
Acked-by: Pratyush Yadav <pratyush@kernel.org>
Reviewed-by: Nutty Liu <nutty.liu@hotmail.com>
Signed-off-by: Tao Liu <ltao@redhat.com>
Link: https://patch.msgid.link/20260705232706.30265-2-ltao@redhat.com
Signed-off-by: Paul Walmsley <pjw@kernel.org>
|
|
https://gitlab.freedesktop.org/drm/misc/kernel into drm-next
drm-misc-next for 7.3:
UAPI Changes:
Cross-subsystem Changes:
Core Changes:
- bridge: Add atomic_create_state callback and helpers, drop atomic_reset
- dp: Add support for DSC max delta BPP
- edid: Parse panel type from DisplayID 2.x Display Parameters
- sysfb: Improve panel, stride and framebuffer size validation
Driver Changes:
- hibmc: Improvements to the plane formats handling, switch to gem-shmem
- nouveau: race fixes, misc improvements
- bridges:
- Convert all bridges to atomic_create_state
- panels:
- panel-edp: New quirks for BOE NE160QDM-NY1, MB116AS01
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <mripard@redhat.com>
Link: https://patch.msgid.link/20260702-powerful-successful-raptor-eded34@houat
|
|
Correct kernel-doc errors for two FCS SMC calls:
INTEL_SIP_SMC_FCS_SEND_CERTIFICATE:
- Describe as async to match STD_CALL_VAL usage
- Replace INTEL_SIP_SMC_FCS_REJECTED with INTEL_SIP_SMC_REJECTED
INTEL_SIP_SMC_FCS_GET_PROVISION_DATA:
- Replace FCS-specific status macros with standard status macros
(INTEL_SIP_SMC_STATUS_ERROR and INTEL_SIP_SMC_STATUS_REJECTED)
- Restore return register documentation for a1 (mailbox error),
a2 (physical address), and a3 (structure size)
Fixes: 4a4709d470e6 ("firmware: stratix10-svc: add new FCS commands")
Fixes: 4b0a32016347 ("firmware: stratix10-svc: change get provision data to async SMC call")
Cc: stable@vger.kernel.org # 6.0+
Signed-off-by: Genevieve Chan <genevieve.chan@altera.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
Fix a memory leak when gen_pool_alloc() fails by freeing pmem on the error
path. Switch pmem allocation from devm_kzalloc() to kzalloc() with
explicit kfree() in the free path to match its list-managed lifetime.
Remove the erroneous list_del(&svc_data_mem) which corrupted the list head
on failed lookups.
Fixes: 7ca5ce896524 ("firmware: add Intel Stratix10 service layer driver")
Cc: stable@vger.kernel.org # 5.0+
Signed-off-by: Tze Yee Ng <tze.yee.ng@altera.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
I'm coming back. I will return. I will possess your body, and I'll
make LKML burn.
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Acked-by: Nathan Chancellor <nathan@kernel.org>
Acked-by: Will Deacon <will@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Rakesh Kota <rakesh.kota@oss.qualcomm.com> says:
Add support for PM4125 USB VBUS regulator. Unlike PM8150B which uses
a current-limit selector, PM4125 uses a 2-bit VBOOST voltage selector
supporting 4.25 V, 4.5 V, 4.75 V and 5.0 V output.
Link: https://patch.msgid.link/20260706-add_pm4125-vbus-reg-v3-0-999d78a87b81@oss.qualcomm.com
|
|
The PM4125 PMIC uses a different register layout for USB VBUS control
compared to PM8150B. On PM4125, CMD_OTG is at offset 0x50, OTG_CFG is
at 0x56, and offset 0x52 is a 2-bit VBOOST voltage selector rather than
a current-limit selector.
Add pm4125_data using the abstraction introduced for PM8150B, along with
dedicated voltage-selector ops and the pm4125_vboost_table covering the
four supported boost voltages: 4.25 V, 4.5 V, 4.75 V, and 5.0 V.
Signed-off-by: Rakesh Kota <rakesh.kota@oss.qualcomm.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://patch.msgid.link/20260706-add_pm4125-vbus-reg-v3-3-999d78a87b81@oss.qualcomm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Introduce per-compatible regulator descriptor data via struct
qcom_usb_vbus_reg_data to abstract register layout differences between
PMICs. This allows the probe function to dynamically populate the
regulator_desc fields rather than relying on compile-time constants.
Refactor the existing PM8150B support to use this abstraction, wiring in
its CMD_OTG, OTG_CFG, and current-limit registers through pm8150b_data.
No functional change is intended for PM8150B.
Signed-off-by: Rakesh Kota <rakesh.kota@oss.qualcomm.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://patch.msgid.link/20260706-add_pm4125-vbus-reg-v3-2-999d78a87b81@oss.qualcomm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The pm4125 PMIC uses a different USB VBUS register layout than pm8150b.
It uses a 2-bit VBOOST voltage selector supporting output voltages of
4.25 V, 4.5 V, 4.75 V and 5.0 V, instead of a current-limit selector.
Move qcom,pm4125-vbus-reg from the pm8150b fallback items list into the
standalone enum since the driver handles it with its own match-data and
register layout.
Make regulator-min/max-microamp conditional so they are only required
for current-limit variants (pm8150b, pm6150, pm7250b, pmi632). Add an
if/then condition for qcom,pm4125-vbus-reg requiring regulator-min/
max-microvolt instead, and update the pm4125 example accordingly.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Rakesh Kota <rakesh.kota@oss.qualcomm.com>
Link: https://patch.msgid.link/20260706-add_pm4125-vbus-reg-v3-1-999d78a87b81@oss.qualcomm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Creating a child cpuset where cpuset.mems is never set leads to a div/0
when a VMA mempolicy with MPOL_F_RELATIVE_NODES rebinds in response to a
CPU hotplug event.
Reproduction steps:
1) Create a cgroup w/ cpuset controls (do not set cpuset.mems)
2) Move the task into the child cpuset
3) Create a VMA mempolicy for that task with MPOL_F_RELATIVE_NODES
4) unplug and hotplug a cpu
echo 0 > /sys/devices/system/cpu/cpu1/online
echo 1 > /sys/devices/system/cpu/cpu1/online
5) mempolicy rebind does a div/0 in mpol_relative_nodemask on the
call to __nodes_fold()
The cpuset code passes (cs->mems_allowed) which is not guaranteed to have
nodes to the rebind routine. Use cs->effective_mems instead, which is
guaranteed to have a non-empty nodemask once we reach that code path.
Link: https://lore.kernel.org/all/CA+0ovCiEz6SP_sn3kN4Tb+_oC=eHMXy_Ffj=usV3wREdQrUtww@mail.gmail.com/
Fixes: ae1c802382f7 ("cpuset: apply cs->effective_{cpus,mems}")
Closes: https://lore.kernel.org/linux-mm/CA+0ovCgxbZkXa+OU8w3s84R3KNPNxxRfmsNR-udh+afQBbGNmw@mail.gmail.com/
Suggested-by: Gregory Price <gourry@gourry.net>
Suggested-by: Waiman Long <longman@redhat.com>
Acked-by: Waiman Long <longman@redhat.com>
Signed-off-by: Farhad Alemi <farhad.alemi@berkeley.edu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Alistair Popple <apopple@nvidia.com>
Cc: Byungchul Park <byungchul@sk.com>
Cc: Gregory Price <gourry@gourry.net>
Cc: "Huang, Ying" <ying.huang@linux.alibaba.com>
Cc: Joshua Hahn <joshua.hahnjy@gmail.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Cc: Rakie Kim <rakie.kim@sk.com>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Zi Yan <ziy@nvidia.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Ridong Chen <ridong.chen@linux.dev>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: "Michal Koutný" <mkoutny@suse.com>
Cc: <stable@vger.kernel.org>
[ david: add a comment, slightly rephrase description ]
Signed-off-by: David Hildenbrand (Arm) <david@kernel.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
The irq-imgpdc driver is controlled by CONFIG_IMGPDC_IRQ, which cannot
be enabled. It used to be selected by CONFIG_SOC_TZ1090, but that was
removed along with the metag architecture in Linux 4.17.
Signed-off-by: Ben Hutchings <benh@debian.org>
Signed-off-by: Thomas Gleixner <tglx@kernel.org>
Link: https://patch.msgid.link/akvddtMQTDKLo2PH@decadent.org.uk
|
|
The automatic CPU-intensive work item detection reads the worker task's
se.sum_exec_runtime without a lock in wq_worker_running(),
wq_worker_tick() and process_one_work(). The scheduler updates that
field under the rq lock (from the tick via update_curr(), or cross-CPU
via task_sched_runtime()), raising:
BUG: KCSAN: data-race in wq_worker_running+0xa8/0xe8
race at unknown origin, with read to 0xffff0009a11d1df8 of 8 bytes by task 238535 on cpu 68:
wq_worker_running
schedule
schedule_preempt_disabled
__mutex_lock
mutex_lock_nested
cgroup_bpf_release
process_one_work
worker_thread
kthread
ret_from_fork
value changed: 0x0000000088482ba0 -> 0x00000000884893c0
The value only feeds a heuristic, so the race is benign-ish. Unlike
commit ecf5aad9a441 ("workqueue: annotate racy PWQ_STAT_CPU_TIME update
in wq_worker_tick()") that only needs data_race(), these are plain reads
whose result drives a subtraction and comparison, so use READ_ONCE() for
a single, non-torn load, which also silences KCSAN.
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
MNE001BS6-2 raw edid:
00 ff ff ff ff ff ff 00 0e 77 86 14 00 00 00 00
0f 24 01 04 a5 1f 11 78 03 2c c5 94 5c 59 95 29
1e 50 54 00 00 00 01 01 01 01 01 01 01 01 01 01
01 01 01 01 01 01 af 2b 80 a0 70 38 28 40 30 20
66 00 36 ad 10 00 00 1a 00 00 00 fd 00 28 3c 43
43 0e 01 0a 20 20 20 20 20 20 00 00 00 fe 00 3d
4c 20 20 20 20 20 20 20 20 20 20 ff 00 00 00 fc
00 4d 4e 45 30 30 31 42 53 36 2d 32 0a 20 01 80
70 20 79 02 00 21 00 1d 15 0c cc 06 80 07 38 04
80 3f 79 5c 9e 05 95 9c f2 1d 02 45 54 b0 5c b0
5c 00 42 12 78 22 00 14 03 22 02 84 7f 07 9f 00
2f 80 1f 00 37 04 27 00 05 00 05 00 2b 00 0c 27
00 28 3b 00 00 27 00 28 3b 00 00 2e 00 06 00 42
b0 5c b0 5c 81 00 1e 72 1a 00 00 03 01 28 3c 00
00 53 ff 53 ff 3c 00 00 00 00 e3 05 04 00 e6 06
01 01 53 53 ff 00 00 00 00 00 00 00 00 00 70 90
MNF601BS4-1 raw edid:
00 ff ff ff ff ff ff 00 0e 77 3f 15 00 00 00 00
0f 24 01 04 a5 22 13 78 03 2c c5 94 5c 59 95 29
1e 50 54 00 00 00 01 01 01 01 01 01 01 01 01 01
01 01 01 01 01 01 ae 2b 80 a0 70 38 28 40 30 20
36 00 58 c1 10 00 00 1a 00 00 00 fd 00 28 3c 44
44 0e 01 0a 20 20 20 20 20 20 00 00 00 fe 00 3d
4c 20 20 20 20 20 20 20 20 20 20 ff 00 00 00 fc
00 4d 4e 46 36 30 31 42 53 34 2d 31 0a 20 01 b6
70 20 79 00 00 21 00 1d 72 0d 90 07 80 07 38 04
80 3f 79 5c 9e 05 95 9c f2 1d 02 45 54 b0 5c b0
5c 00 42 12 78 22 00 14 04 22 02 84 7f 07 9f 00
2f 00 1f 00 37 04 27 00 02 00 05 00 2b 00 0c 27
00 28 3b 00 00 27 00 28 3b 00 00 2e 00 06 00 42
b0 5c b0 5c 81 00 1e 72 1a 00 00 03 01 28 3c 00
00 4b ff 4b ff 3c 00 00 00 00 e3 05 04 00 e6 06
01 01 53 53 ff 00 00 00 00 00 00 00 00 00 e1 90
Signed-off-by: Haikun Zhou <zhouhaikun5@huaqin.corp-partner.google.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patch.msgid.link/20260706080333.41426-1-zhouhaikun5@huaqin.corp-partner.google.com
|
|
Move irq_set_chip_and_handler() and irq_set_status_flags() calls
outside the io7->irq_lock raw spinlock. These functions take
sparse_irq_lock, which is a mutex, and taking a sleeping lock while
holding a raw spinlock is invalid. The raw spinlock only needs to
protect the hardware CSR accesses.
This fixes the following lockdep splat during boot:
[ BUG: Invalid wait context ]
swapper/0/0 is trying to lock:
sparse_irq_lock{....}-{4:4}, at: irq_mark_irq
other info that might help us debug this:
context-{5:5}
1 lock held by swapper/0/0:
#0: &io7->irq_lock{....}-{2:2}, at: init_io7_irqs.constprop.0
Cc: stable@vger.kernel.org
Assisted-by: Claude:claude-opus-4-6
Signed-off-by: Matt Turner <mattst88@gmail.com>
Reviewed-by: Magnus Lindholm <linmag7@gmail.com>
Link: https://lore.kernel.org/r/20260528230516.1839694-2-mattst88@gmail.com
Signed-off-by: Magnus Lindholm <linmag7@gmail.com>
|
|
Pass base + i to irq_set_status_flags() to match the IRQ number
used in irq_set_chip_and_handler(). Previously, IRQ_LEVEL was set
on the wrong (low-numbered) IRQ descriptors rather than the IO7
IRQs at base + i.
Cc: stable@vger.kernel.org
Fixes: 08876fe8519c ("alpha: marvel: Convert irq_chip functions")
Signed-off-by: Matt Turner <mattst88@gmail.com>
Reviewed-by: Magnus Lindholm <linmag7@gmail.com>
Link: https://lore.kernel.org/r/20260528230516.1839694-1-mattst88@gmail.com
Signed-off-by: Magnus Lindholm <linmag7@gmail.com>
|
|
arch/alpha/include/asm/device.h simply includes <asm-generic/device.h>,
and therefore the Alpha-specific version is unnecessary. Remove it.
Signed-off-by: Ethan Nelson-Moore <enelsonmoore@gmail.com>
Reviewed-by: Magnus Lindholm <linmag7@gmail.com>
Link: https://lore.kernel.org/r/20260517233246.23915-1-enelsonmoore@gmail.com
Signed-off-by: Magnus Lindholm <linmag7@gmail.com>
|
|
HDMA clock is responsible for the internal TCM access path of X100 RISC-V
core, so set the clock flag as critical to prevent it from being shut off,
otherwise the Linux system will hang, for example in the case of a vector
instruction access generates a page fault.
Fixes: e371a77255b8 ("clk: spacemit: k3: add the clock tree")
Reported-by: Han Gao <gaohan@iscas.ac.cn>
Tested-by: Aurelien Jarno <aurelien@aurel32.net>
Link: https://patch.msgid.link/20260630-06-clk-hdma-critial-v1-1-443c0ac88c5f@kernel.org
Signed-off-by: Yixun Lan <dlan@kernel.org>
|
|
Remove single ')'.
Signed-off-by: Manuel Ebner <manuelebner@mailbox.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
In tracing_set_tracer(), the assignment 'ret = 0' following the
__tracing_resize_ring_buffer() error check is a dead store. After
this point, all subsequent code paths either return with a constant
value (-EINVAL, 0, -EBUSY) or reassign ret before reading it
(tracing_arm_snapshot_locked, tracer_init).
Remove the unnecessary assignment.
No functional change.
Link: https://patch.msgid.link/6a2a37c4.f0a9eb5a.2fc603.7724@mx.google.com
Signed-off-by: Wayen.Yan <win847@gmail.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
CONFIG_PM_WAKELOCKS_LIMIT is documented as the maximum number of
user-space wakeup sources, but the limit check is performed before
the counter is incremented and only rejects new wakeup sources when the
current number is greater than the limit. This allows one extra wakeup
source to be created.
Reject new wakeup sources once the counter has reached the limit.
Fixes: b86ff9820fd5 ("PM / Sleep: Add user space interface for manipulating wakeup sources, v3")
Signed-off-by: Haowen Tu <tuhaowen@uniontech.com>
[ rjw: Subject edits ]
Link: https://patch.msgid.link/20260624053839.2150567-1-tuhaowen@uniontech.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This ensures that any RCU readers traversing the instance list
have finished, before releasing the reference on the tracer that
the instance points to.
Cc: stable@vger.kernel.org
Fixes: a6ed2aee54644 ("tracing: Switch to kvfree_rcu() API")
Link: https://patch.msgid.link/20260609045430.1589786-1-crwood@redhat.com
Suggested-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Crystal Wood <crwood@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
When RB_FORCE_8BYTE_ALIGNMENT is true, rb_calculate_event_length()
reserves the space of event->array[0] for placing the data length and
rb_update_event() stores the data length in event->array[0]
accordingly. As a result the whole event length will add extra 4 bytes
for sizeof(event.array[0]) unconditionally.
But ring_buffer_event_length() only subtracts the
sizeof(event->array[0]) for events larger than RB_MAX_SMALL_DATA +
sizeof(event->array[0]). As a result, small events on architectures
with RB_FORCE_8BYTE_ALIGNMENT=true report a data length that is 4
bytes larger than expected.
To fix it, add the RB_FORCE_8BYTE_ALIGNMENT as a condition to subtract
the size of that length field whenever RB_FORCE_8BYTE_ALIGNMENT is
true.
This issue is observed in a riscv64 kernel with
CONFIG_HAVE_64BIT_ALIGNED_ACCESS set to y, when we run ftrace selftest
trace_marker_raw.tc, we get the weird log: for cases where the id is
1..100, the number of data field is 8*N, but once id exceeds 100, the
number of data field becomes 8*N+4:
# 1 buf: 58 00 00 00 80 5e d1 63 (number of data field is 8*1)
...
# a buf: 58 ... (number of data field is 8*2)
...
# 64 buf: 58 ... (number of data field is 8*13)
# 65 buf: 58 ... (number of data field is 8*13+4)
After applying this change, the number of data field keeps being 8*N+4
consistently.
Link: https://patch.msgid.link/20260607072431.125633-2-hui.wang@canonical.com
Fixes: 2271048d1b3b ("ring-buffer: Do 8 byte alignment for 64 bit that can not handle 4 byte align")
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Reviewed-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
sysc_init_stdout_path() gets the /chosen node with
of_find_node_by_path() to read stdout-path. The function then overwrites
the local node pointer with the stdout-path lookup result, or exits on
error, without dropping the /chosen reference.
Keep the /chosen node in a separate variable and put it after the
stdout-path value has been used for the lookup. The successful stdout
node lookup remains referenced by the cached stdout_path pointer.
Fixes: 3bb37c8e6e6a ("bus: ti-sysc: Handle stdout-path for debug console")
Signed-off-by: Yuho Choi <dbgh9129@gmail.com>
Reviewed-by: Andreas Kemnade <andreas@kemnade.info>
Link: https://patch.msgid.link/20260615200540.770205-1-dbgh9129@gmail.com
Signed-off-by: Kevin Hilman (TI) <khilman@baylibre.com>
|
|
Enable drivers needed to use RGB LEDs composed of multiple monochromatic
LEDs.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Link: https://patch.msgid.link/20260702-b200multiled-v1-2-c1799ad45c96@kemnade.info
Signed-off-by: Kevin Hilman (TI) <khilman@baylibre.com>
|
|
The device has one single RGB LED. Explicitly declare it as such
by combing the LEDs into one.
Suggested-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Link: https://patch.msgid.link/20260702-b200multiled-v1-1-c1799ad45c96@kemnade.info
Signed-off-by: Kevin Hilman (TI) <khilman@baylibre.com>
|
|
nvmet_execute_auth_receive() allocates the response buffer with kmalloc()
sized by the host-supplied AUTH_RECEIVE allocation length, but the
DH-HMAC-CHAP builders write only a fixed-size message into it. The full
allocation length is then copied to the wire by nvmet_copy_to_sgl(), so a
remote initiator receives the bytes past the built message -- up to nearly
a page of uninitialized slab -- during the pre-authentication handshake.
Allocate the buffer with kzalloc() so the unwritten tail is zeroed before
it is sent; conforming responses are unaffected.
Fixes: db1312dd9548 ("nvmet: implement basic In-Band Authentication")
Cc: stable@vger.kernel.org
Signed-off-by: Bryam Vargas <hexlabsecurity@proton.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
|
DH-HMAC-CHAP authentication compares HMAC response digests with memcmp().
Standard memcmp() may stop at the first differing byte, which can leak
timing information to a remote attacker and allow incremental recovery
of the expected digest.
Use crypto_memneq() for constant-time comparison on both the host path
that validates the controller Success1 response and the target path that
validates the host Reply digest. Other memcmp() uses in the NVMe auth
code (e.g. fixed string prefix checks) are not security-sensitive and
are left unchanged.
Signed-off-by: Xixin Liu <liuxixin@kylinos.cn>
Reviewed-by: Hannes Reinecke <hare@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
|
Correct spaces or mix of tabs+spaces into proper tab-indented lines.
No functional impact (same DTB).
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://patch.msgid.link/20260706101815.341184-2-krzysztof.kozlowski@oss.qualcomm.com
Signed-off-by: Kevin Hilman (TI) <khilman@baylibre.com>
|
|
Function __nvme_submit_sync_cmd() returns a positive error code for NVMe
errors. Otherwise, we get 0 for success or a negative error code for a
kernel error.
In nuse_show() -> ns_{head}_update_nuse() -> nvme_identify_ns() ->
nvme_submit_sync_cmd() -> __nvme_submit_sync_cmd(), we then may get a
positive error code returned.
Function nuse_show() - being a device attr handler - should return the
number of bytes written to the buffer or a negative error code.
Convert any positive NVMe error code to -EIO.
Signed-off-by: John Garry <john.g.garry@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
|
Make the checks in hybrid_get_cost() more straightforward.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://patch.msgid.link/2832945.mvXUDI8C0e@rafael.j.wysocki
|
