| Age | Commit message (Collapse) | Author |
|---|
|
After the former refactoring the existing otto_emdio_9300_mdiobus_init()
contains only the c22/c45 bus mode setup. Like the topology setup this
must run before bus registration. Otherwise the bus does not "speak" the
right protocol for PHY setup.
This setup is device-specific and other SoCs will need to set up other
register bits in the controller in the future. Therefore
- Relocate c22/c45 device tree readout to the very beginning of the probing
- Add a new device-specific setup_controller() into the info structure.
- Relocate otto_emdio_priv to satisfy the new info structure dependency.
- Rename otto_emdio_9300_mdiobus_init accordingly and add it to the
RTL9300 info structure. At the same time, adapt register naming
for the function to make it clear that it only applies to this SoC.
- Call setup_controller() prior to bus registration.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://patch.msgid.link/20260603175924.123019-7-markus.stockhausen@gmx.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
otto_emdio_map_ports() is the central place to lookup the topology and the
properties of the Realtek ethernet MDIO controller from the device tree.
Deviating from this the c22/c45 detection via "ethernet-phy-ieee802.3-c45"
is running separately in otto_emdio_probe_one(). It loops over the same
nodes, just at a later point in time.
There is no benefit to divide this setup and to have a time window where
the data structure is only filled partially. Additionally it uses the
"fwnode" API. Consolidate the setup and convert it to the "of" API.
Remark. This is a subtle change for dangling PHY nodes (not referenced
by ethernet-ports). Before this commit all PHY nodes were evaluated for
c45 setup, now only the referenced ones.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://patch.msgid.link/20260603175924.123019-6-markus.stockhausen@gmx.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Until now the driver sets up the port to bus/address topology of the
controller after all buses are set up via otto_emdio_probe_one(). This
does not work for devices where U-Boot skips this setup. It is not
only needed for the hardware internal background PHY polling engine
but it is essential for access to the PHYs during probing.
Depending on the SoC type there exist two different register arrays
- Bus mapping registers (RTL930x, RTL931x) define to which bus the port
is attached. E.g. [1]
- Address mapping registers (RTL838x, RTL930x, RTL931x) define to which
address of the bus the port is attached. E.g. [2]
Relocate the topology setup and make it generic. For this
- Define device-specific bus_base/addr_base attributes that give the
register base address where the mapping lives. In case one or both are
not given the SoC does not support this specific type of mapping.
- Create a helper otto_emdio_setup_topology() that writes the detected
topology to the registers.
- Call this helper prior to otto_emdio_probe_one().
- Remove unneeded code from otto_emdio_9300_mdiobus_init().
- Due to the added prefixes, increase define indentation
Subtle change: The old coding used regmap_bulk_write and silently wrote
bus=0/address=0 to mapping registers for ports that are out of scope.
The new coding leaves those untouched.
[1] https://svanheule.net/realtek/longan/register/smi_port0_15_polling_sel
[2] https://svanheule.net/realtek/longan/register/smi_port0_5_addr_ctrl
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://patch.msgid.link/20260603175924.123019-5-markus.stockhausen@gmx.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The bus probing of the MDIO driver uses a two stage approach.
1. The device tree "ethernet-ports" node is scanned to build a mapping
between ports and PHYs.
2. The children of the device tree "controller" are scanned to create
the individual MDIO buses.
The first step already checks the consistency of the PHY and bus nodes
that are linked via the ports. But it might miss a dangling bus child
node that is not linked. Step two simply iterates over all bus child
nodes and might read malformed data from nodes not checked in step one.
Harden this and return a meaningful error message.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://patch.msgid.link/20260603175924.123019-4-markus.stockhausen@gmx.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Due to its design the MDIO driver needs to set up a port to bus/address
mapping during probing. The "ethernet-ports" subnodes are scanned and
from the "phy-handle" property the MDIO nodes are looked up. In case of
a malformed device tree the driver might produce out-of-bounds accesses.
The PHY address is not checked against the maximum supported address.
Add a sanity check and drop the unneeded MAX_SMI_ADDR define.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://patch.msgid.link/20260603175924.123019-3-markus.stockhausen@gmx.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This function has multiple issues:
- It uses __free low level cleanups
- It mixes "fwnode" and "of" functions
Convert this to a uniform "of" usage and manual reference counting
cleanup. With that also fix two subtle lookup bugs in the original
code.
mdio_dn = phy_dn->parent;
if (mdio_dn->parent != dev->of_node)
continue;
This skips an API access and therefore misses reference counting.
Additionally in the case of a very buggy device tree, phy_dn might
be a root node. Looking up its grandparent leads to a NULL pointer
access.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://patch.msgid.link/20260603175924.123019-2-markus.stockhausen@gmx.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The firmware advertises context memory (backing store) types
through a linked list, with BNGE_CTX_INV serving as the
end-of-list sentinel.
However, the driver incorrectly assumes that the list is strictly
ordered and prematurely terminates traversal when it encounters
an unrecognized type (>=BNGE_CTX_V2_MAX). As a result, any valid
context types that appear later in the chain are silently skipped,
leading to incomplete memory configuration and eventual driver load
failure.
Fix this by traversing the entire list until the BNGE_CTX_INV sentinel
is reached, while safely ignoring only those context types that fall
outside the supported range.
Fixes: 29c5b358f385 ("bng_en: Add backing store support")
Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Reviewed-by: Dharmender Garg <dharmender.garg@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Bit 16 of the MAC HW Feature1 register reports the DCB (Data Centre
Bridging) feature. Read it so that dma_cap.dcben and the debugfs
report it accurately. Right now it is always reported as being disabled.
Signed-off-by: Ovidiu Panait <ovidiu.panait.rb@renesas.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20260603173644.24371-1-ovidiu.panait.rb@renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add dma_rmb() barrier after req_id completion check in
ena_com_phc_get_timestamp(). On weakly-ordered architectures,
payload fields may be read before req_id is observed as updated.
Fixes: e0ea34158ee8 ("net: ena: Add PHC support in the ENA driver")
Closes: https://sashiko.dev/#/patchset/20260430032507.11586-1-akiyano%40amazon.com
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
airoha_qdma_init_hfwd_queues()
of_reserved_mem_lookup() may return NULL if the reserved memory region
referenced by the "memory-region" phandle is not found in the reserved
memory table (e.g. due to a misconfigured DTS or a removed
memory-region node). The current code dereferences the returned
pointer without checking for NULL, leading to a kernel NULL pointer
dereference at the following lines:
dma_addr = rmem->base; // line 1156
num_desc = div_u64(rmem->size, buf_size); // line 1160
Add a NULL check after of_reserved_mem_lookup() and return -ENODEV if
the lookup fails, which is consistent with the existing error handling
for of_parse_phandle() failure in the same code block.
Fixes: 3a1ce9e3d01b ("net: airoha: Add the capability to allocate hwfd buffers via reserved-memory")
Cc: stable@vger.kernel.org
Signed-off-by: ZhaoJinming <zhaojinming@uniontech.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The HSR generic netlink family sets .netnsok = true. HSR devices can
live in network namespaces other than init_net.
Two async notifiers broadcast events with genlmsg_multicast(). They
are hsr_nl_ringerror() and hsr_nl_nodedown(). That helper delivers
only on the default genl socket in init_net. So the events always land
in init_net. The network namespace of the device does not matter.
This has two effects. A listener in the device's own namespace never
sees its own ring error and node down events. A privileged listener in
init_net receives events from HSR devices in other namespaces. The
payload carries the peer node MAC (HSR_A_NODE_ADDR) and the slave port
ifindex (HSR_A_IFINDEX).
Switch both callers to genlmsg_multicast_netns(). Other families with
.netnsok = true already do this. Examples are gtp, ovpn, team,
batman-adv, netdev-genl, ethtool and handshake.
hsr_nl_ringerror() already has the slave port. It uses
dev_net(port->dev). hsr_nl_nodedown() takes the namespace from the
master port via hsr_port_get_hsr().
Reviewed-by: Fernando Fernandez Mancera <fmancera@suse.de>
Signed-off-by: Maoyi Xie <maoyixie.tju@gmail.com>
Link: https://patch.msgid.link/20260604054949.2999304-1-maoyixie.tju@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Bobby Eshleman says:
====================
net: devmem: allow bind-rx from non-init user namespaces
NETDEV_CMD_BIND_RX is GENL_ADMIN_PERM, which checks CAP_NET_ADMIN
against init_user_ns. With netkit and netns support for devmem, it is
now useful to let workloads holding CAP_NET_ADMIN only in their own
user_ns issue bind-rx for a netns owned by that user_ns.
The first patch switches the flag to GENL_UNS_ADMIN_PERM so the check
uses the target netns's owning user_ns. Init remains permitted.
The second patch just adds test cases. They are identical to
nk_devmem.py tests, but using a non-init userns.
====================
Link: https://patch.msgid.link/20260602-nl-prov-v2-0-ad721142c641@meta.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add userns_devmem.py, which mirrors nk_devmem.py but places the netkit
guest in a netns whose owning user_ns is non-init. ncdevmem is ran there
via nsenter so the bind-rx call is issued with creds that hold
CAP_NET_ADMIN only in the child user_ns.
Without the preceding GENL_UNS_ADMIN_PERM patch the test fails at
bind-rx with EPERM, but with the patch the transfer completes and tests
pass.
Signed-off-by: Bobby Eshleman <bobbyeshleman@meta.com>
Acked-by: Stanislav Fomichev <sdf@fomichev.me>
Link: https://patch.msgid.link/20260602-nl-prov-v2-2-ad721142c641@meta.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
NETDEV_CMD_BIND_RX is currently GENL_ADMIN_PERM, which checks
CAP_NET_ADMIN against init userns. With recent container/netkit/ns
support for devmem, other userns/netns use cases come online and require
bind-rx to allow CAP_NET_ADMIN in non-init user ns as well.
Switch the flag to GENL_UNS_ADMIN_PERM to allow bind-rx for
CAP_NET_ADMIN in the netns's owning userns as well.
Signed-off-by: Bobby Eshleman <bobbyeshleman@meta.com>
Acked-by: Stanislav Fomichev <sdf@fomichev.me>
Link: https://patch.msgid.link/20260602-nl-prov-v2-1-ad721142c641@meta.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Pull drm fixes from Dave Airlie:
"Weekly drm fixes, not contributing to things settling down
unfortunately. Lots of driver fixes for various bounds checks, leaks
and UAF type things, i915/xe probably the most sane, amdgpu has a mix
of fixes all over, then ethosu has lots of small fixes.
The problem of fixing thing in private has really hit us with the
change handle ioctl, and "Sima was right" and we should have disabled
the ioctl, since it was only introduced a couple of kernels ago and
failed to upstream it's tests in time.
The patch here fixes the problems Sima identified, but disables the
ioctl as well, with a list of known problems in it and a request for
proper tests to be written and upstreamed. It's a niche user ioctl
designed for CRIU with AMD ROCm, so I think it's fine to just disable
it.
Maybe this week will settle down.
core:
- disable the gem change handle ioctl for security reasons (plan to
fix it on list later with proper test coverage)
dumb-buffer:
- remove strict limits on buffer geometry
amdgpu:
- BT.2020 fix for DCE
- DC bounds checking fixes
- SDMA 7.1 fix
- UserQ fixes
- SI fix
- SMU 13 fixes
- SMU 14 fixes
- GC 12.1 fix
- Userptr fix
- GC 10.1 fix
- GART fix for non-4K pages
amdkfd:
- UAF race fix
- Fix a potential NULL pointer dereference
- GC 11 buffer overflow fix for SDMA
xe:
- Revert removing support for unpublished NVL-S GuC
- Suspend fixes related to multi-queue
i915:
- Fix color blob reference handling in intel_plane_state
- Revert "drm/i915/backlight: Remove try_vesa_interface"
ethosu:
- reject unsupported NPU_OP_RESIZE
- fix index of IFM region
- fix weight index
- fix overflows in DMA-size calculations
- reject DMA commands with uninitialized length
- fix OOB write in ethosu_gem_cmdstream_copy_and_validate
imx:
- fix kernel-doc warnings
ivpu:
- add overflow checks in firmware handling and get_info_ioctl
v3d:
- wait for pending L2T flush before cleaning caches
- fix leak of vaddr
- skip CSD when it has zeroed workgroups
- fix ref counting in performance monitoring"
* tag 'drm-fixes-2026-06-06' of https://gitlab.freedesktop.org/drm/kernel: (50 commits)
drm/gem: Try to fix change_handle ioctl, attempt 4
Revert "drm/i915/backlight: Remove try_vesa_interface"
accel/ethosu: fix OOB write in ethosu_gem_cmdstream_copy_and_validate()
accel/ethosu: reject DMA commands with uninitialized length
accel/ethosu: fix arithmetic issues in dma_length()
accel/ethosu: fix wrong weight index in NPU_SET_SCALE1_LENGTH on U85
accel/ethosu: reject NPU_OP_RESIZE commands from userspace
accel/ethosu: fix IFM region index out-of-bounds in command stream parser
drm/v3d: Fix global performance monitor reference counting
drm/xe/multi_queue: skip submit when primary queue is suspended
drm/xe: Clear pending_disable before signaling suspend fence
Revert "drm/xe: Skip exec queue schedule toggle if queue is idle during suspend"
drm/amd/pm: smu_v14_0_0: use SoftMin for gfxclk in set_soft_freq_limited_range
drm/amdgpu: Fix incorrect VRAM GART mappings on non-4K page size systems
drm/amdgpu/userq: move wptr_obj cleanup in mqd_destroy
drm/amdgpu: improve the userq seq BO free bit lookup
drm/amdgpu/userq: remove the vital queue unmap logging
drm/amdkfd: Fix buffer overflow in SDMA queue checkpoint/restore on GFX11
drm/amdkfd: fix NULL dereference in get_queue_ids()
drm/amdgpu: set noretry=1 as default for GFX 10.1.x (Navi10/12/14)
...
|
|
These symbols don't need to be exported, they are only used from vmlinux:
- inet6addr_notifier_call_chain
- inet6addr_validator_notifier_call_chain
- in6addr_linklocal_allnodes
- in6addr_linklocal_allrouters
- in6addr_interfacelocal_allnodes
- in6addr_interfacelocal_allrouters
- in6addr_sitelocal_allrouters
- inet6_cleanup_sock
- ip6_sk_dst_lookup_flow
- ipv6_proxy_select_ident
- ip6_sk_update_pmtu
- ip6_sk_redirect
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://patch.msgid.link/20260604174555.2801532-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
These symbols no longer need to be exported, they are only used from
vmlinux:
- inet_send_prepare
- inet_splice_eof
- inet_sk_rebuild_header
- inet_current_timestamp
- snmp_fold_field
- snmp_get_cpu_field64
- snmp_fold_field64
- fib_nh_common_release
- fib_nh_common_init
- fib_nexthop_info
- fib_add_nexthop
- ip_build_and_send_pkt
- ipv4_sk_update_pmtu
- ipv4_sk_redirect
- rt_dst_clone
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://patch.msgid.link/20260604173413.2782008-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Eric Dumazet says:
====================
bridge: prepare lockless br_port_fill_attrs() (I)
medium-term goal is to allow "ip link show" dump commands to run without RTNL.
This round of patches adds/fixes some lockess accesses in bridge.
This is not complete, more patches will come later.
Ultimately all changes to p->flags should use set_bit()/clear_bit().
I repeat (AI agents might read this cover ?):
Many p->flags accesses are racy, and will hopefully be fixed in a
future series.
====================
Link: https://patch.msgid.link/20260604141343.2124500-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We might run br_port_fill_attrs() locklessly in the future.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://patch.msgid.link/20260604141343.2124500-12-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Needed for sysfs show_config_pending(), BRCTL_GET_PORT_INFO
and upcoming RTNL avoidance in "ip link" dumps (cf br_port_fill_attrs()).
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://patch.msgid.link/20260604141343.2124500-11-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
sysfs show_port_id() and BRCTL_GET_PORT_INFO need this.
This will be needed for upcoming RTNL avoidance in "ip link"
dumps (cf br_port_fill_attrs()).
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://patch.msgid.link/20260604141343.2124500-10-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
sysfs show_priority() needs this.
Also br_port_fill_attrs() might in the future run without RTNL.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://patch.msgid.link/20260604141343.2124500-9-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add READ_ONCE()/WRITE_ONCE() annotations around p->designated_port
This is needed at least for sysfs show_designated_port(), BRCTL_GET_PORT_INFO
and upcoming RTNL avoidance in "ip link" dumps (cf br_port_fill_attrs()).
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://patch.msgid.link/20260604141343.2124500-8-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add READ_ONCE()/WRITE_ONCE() annotations around p->designated_cost
This is needed at least for sysfs show_designated_cost(), BRCTL_GET_PORT_INFO
and upcoming RTNL avoidance in "ip link" dumps (cf br_port_fill_attrs()).
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/20260604141343.2124500-7-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add READ_ONCE()/WRITE_ONCE() annotations around p->path_cost.
This is needed at least for sysfs show_path_cost(), BRCTL_GET_PORT_INFO
and upcoming RTNL avoidance in "ip link" dumps (cf br_port_fill_attrs()).
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/20260604141343.2124500-6-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use set_bit() and test_bit() lockless functions.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://patch.msgid.link/20260604141343.2124500-5-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use BR_PROMISC_BIT and set_bit(), clear_bit() and test_bit() lockless
functions.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://patch.msgid.link/20260604141343.2124500-4-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We want to use atomic operations for lockless p->flags changes
and reads.
Add definitions for bits in addition of masks so that we can use
test_bit(), clear_bit() and set_bit() in subsequent patches.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://patch.msgid.link/20260604141343.2124500-3-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
br_timer_value() can be called locklessly, the expires field
could be changed concurrently.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://patch.msgid.link/20260604141343.2124500-2-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
By default, pppd attempts to detect loopbacks on the underlying
interface using a pseudo-randomly generated magic number and checks if
the same value is received. The seed for the PRNG is a hash of hostname
XOR current time XOR pid, which is likely to collide on NIPA, causing
false positives. Disable magic number generation.
Reported-by: Matthieu Baerts <matttbe@kernel.org>
Fixes: 7af2a94f4dcf ("selftests: net: add tests for PPPoL2TP")
Signed-off-by: Qingfang Deng <qingfang.deng@linux.dev>
Link: https://patch.msgid.link/20260603061746.23452-1-qingfang.deng@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
cpsw_probe() registers devlink before registering the CPSW ports.
If cpsw_register_ports() fails, the error path only unregisters the
notifiers and then releases the lower level resources. It does not undo
the successful cpsw_register_devlink() call, leaving the devlink instance
and its parameters registered after probe has failed.
Add a devlink cleanup label for the path where devlink registration has
already succeeded, and use it when port registration fails.
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Signed-off-by: Guangshuo Li <lgs201920130244@gmail.com>
Link: https://patch.msgid.link/20260604043115.1409134-1-lgs201920130244@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2026-06-02 (ice, idpf)
Petr Oros adds missing callbacks for U.FL DPLL pins on ice.
Alok Tiwari corrects copy/paste error causing incorrect reporting of PTP
mailbox capability for idpf.
====================
Link: https://patch.msgid.link/20260602225513.393338-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The current code incorrectly uses VIRTCHNL2_CAP_PTP_SET_DEVICE_CLK_TIME
for both direct and mailbox capabilities, causing mailbox-only support
to be ignored and potentially reporting IDPF_PTP_NONE.
Fixes: d5dba8f7206da ("idpf: add PTP clock configuration")
Signed-off-by: Alok Tiwari <alok.a.tiwari@oracle.com>
Tested-by: Samuel Salin <Samuel.salin@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20260602225513.393338-4-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The U.FL2 input pin advertises DPLL_PIN_CAPABILITIES_PRIORITY_CAN_CHANGE
in its capability mask, but ice_dpll_pin_ufl_ops does not provide
.prio_get and .prio_set callbacks. As a result the DPLL subsystem
cannot report or accept priority for U.FL pins: pin-get omits the prio
field on U.FL2 and pin-set with prio is rejected as invalid, even
though the capability is present. This prevents user space from using
priority to select or disable U.FL2 as a DPLL input source.
Reproducer with iproute2 (dpll command):
# dpll pin show board-label U.FL2
pin id 16:
module-name ice
board-label U.FL2
type ext
capabilities priority-can-change|state-can-change
parent-device:
id 0 direction input state selectable phase-offset 0
/* note: no "prio" between "direction" and "state",
even though priority-can-change is advertised */
# dpll pin set id 16 parent-device 0 prio 5
RTNETLINK answers: Operation not supported
After the fix the prio field is reported by pin show and pin set with
prio is accepted on U.FL2.
Add the missing .prio_get and .prio_set callbacks to
ice_dpll_pin_ufl_ops, reusing ice_dpll_sw_input_prio_{get,set}. The
same ops struct is shared by U.FL1 and U.FL2: U.FL2 (input) delegates
to the backing hardware input pin, while U.FL1 (output) does not
advertise DPLL_PIN_CAPABILITIES_PRIORITY_CAN_CHANGE so the dpll core
capability gate never invokes prio_set for it, and prio_get reports
the OUTPUT sentinel (ICE_DPLL_PIN_PRIO_OUTPUT) on the output side
exactly like the SMA path does today.
Fixes: 2dd5d03c77e2 ("ice: redesign dpll sma/u.fl pins control")
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Petr Oros <poros@redhat.com>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20260602225513.393338-3-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Since commit 68a99f6a0ebf ("media: lirc: report ir receiver overflow"),
the rc-loopback driver does not accept edges over 50ms, as these are
never seen in real life ir protocols. Fix this.
Signed-off-by: Sean Young <sean@mess.org>
Link: https://lore.kernel.org/r/20260605151417.777614-1-sean@mess.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Xu Kuohai says:
====================
Add validation for bpf_set_retval helper
From: Xu Kuohai <xukuohai@huawei.com>
The bpf_set_retval() helper is used by cgroup BPF programs to set the
return value of the kernel hook. The argument type for this helper is
ARG_ANYTHING. This allows setting a positive value, which no cgroup
hook expects and can cause issues, such as the kernel panic reported
in [1].
This series adds validation for the argument of the bpf_set_retval()
helper.
For BPF_LSM_CGROUP, the same validation as BPF_LSM_MAC is enforced,
i.e. validate the argument against the LSM hook specific range, which
is returned by bpf_lsm_get_retval_range().
For all other cgroup program types, restrict the argument to
[-MAX_ERRNO, 0], which matches the kernel convention of 0 for success
and negative errno for error.
BPF_CGROUP_GETSOCKOPT is an exception from this restriction, since valid
getsockopt implementations may return positive values (e.g. optlen), as
allowed by commit c4dcfdd406aa ("bpf: Move getsockopt retval to struct
bpf_cg_run_ctx").
[1] https://lore.kernel.org/all/567d3206-74a5-44e5-99c6-779c425f399e@std.uestc.edu.cn
v5:
- Use resolve_prog_type(env->prog) instead of env->prog->type for prog type checks
- Target bpf-next tree
v4: https://lore.kernel.org/bpf/20260604130458.617765-1-xukuohai@huaweicloud.com
- Remove the return value limit for BPF_CGROUP_GETSOCKOPT type
- Refine the range of return value of bpf_get_retval helper
v3: https://lore.kernel.org/bpf/20260530101239.590395-1-xukuohai@huaweicloud.com/
- Mark R1 as precise to prevent validation bypass via branch pruning (sashiko)
v2: https://lore.kernel.org/bpf/20260530055557.549474-1-xukuohai@huaweicloud.com/
- Extend validation from LSM cgroup BPF type to all cgroup BPF types (sashiko)
v1: https://lore.kernel.org/bpf/20260523085806.417723-1-xukuohai@huaweicloud.com/
====================
Link: https://patch.msgid.link/20260605140243.664590-1-xukuohai@huaweicloud.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Add verifier tests to validate bpf_set_retval argument for cgroup
program types.
Reviewed-by: Emil Tsalapatis <emil@etsalapatis.com> #v1
Signed-off-by: Xu Kuohai <xukuohai@huawei.com>
Link: https://lore.kernel.org/r/20260605140243.664590-4-xukuohai@huaweicloud.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
The bpf_set_retval() helper is used by cgroup BPF programs to set the
return value of the target hook. The argument type for this helper is
ARG_ANYTHING. This allows setting a positive value, which no cgroup
hook expects and can cause issues, such as:
- BPF_LSM_CGROUP: a positive value from bpf_lsm_socket_create bypasses
the err < 0 check in __sock_create(), leaving the socket object
unallocated. The positive return value is then propagated to the
syscall entry __sys_socket(), which also bypasses the IS_ERR() guard
and ultimately causes a NULL pointer dereference.
- BPF_CGROUP_DEVICE: a positive value can be returned through cgroup
device bpf prog -> devcgroup_check_permission() -> bdev_permission()
-> bdev_file_open_by_dev(), where ERR_PTR(positive) produces a pointer
that IS_ERR() does not catch, leading to a wild pointer dereference.
- BPF_CGROUP_SOCK: a positive value can be returned through cgroup sock
bpf prog -> __cgroup_bpf_run_filter_sk() -> inet_create() ->
__sock_create(), where inet_create() frees the newly allocated sk
via sk_common_release() and sets sock->sk = NULL on the non-zero
return, but __sock_create() only checks err < 0 for cleanup, so a
positive retval bypasses cleanup and returns a socket with NULL sk
to userspace, triggering a NULL pointer dereference on subsequent
socket operations.
- BPF_CGROUP_SYSCTL: a positive value can be returned through the cgroup
bpf prog -> __cgroup_bpf_run_filter_sysctl() -> proc_sys_call_handler(),
where a non-zero return bypasses the normal sysctl proc_handler and is
returned directly to userspace as return value of read() or write()
syscall.
So add validation for the argument of the bpf_set_retval() helper.
For BPF_LSM_CGROUP, enforce the LSM hook specific range returned by
bpf_lsm_get_retval_range().
For all other cgroup program types, restrict the argument to
[-MAX_ERRNO, 0], which matches the kernel convention of 0 for success
and negative errno for error.
BPF_CGROUP_GETSOCKOPT is an exception, since valid getsockopt
implementations may return positive values, as allowed by commit
c4dcfdd406aa ("bpf: Move getsockopt retval to struct bpf_cg_run_ctx").
Also refine the return value range of bpf_get_retval() so that
values returned by bpf_get_retval() can be passed directly to
bpf_set_retval() without extra manual bounds checking.
Fixes: b44123b4a3dc ("bpf: Add cgroup helpers bpf_{get,set}_retval to get/set syscall return value")
Fixes: 69fd337a975c ("bpf: per-cgroup lsm flavor")
Reported-by: Quan Sun <2022090917019@std.uestc.edu.cn>
Closes: https://lore.kernel.org/all/567d3206-74a5-44e5-99c6-779c425f399e@std.uestc.edu.cn
Signed-off-by: Xu Kuohai <xukuohai@huawei.com>
Link: https://lore.kernel.org/r/20260605140243.664590-3-xukuohai@huaweicloud.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Test sk_bypass_prot_mem passes an unchecked value as argument to helper
bpf_set_retval(). The argument can be outside the valid range enforced
by the strict retval validation added in the next patch.
Restrict the argument to -EFAULT when it is outside the valid range, so
the test will not be rejected by the verifier when retval validation
is enforced.
Signed-off-by: Xu Kuohai <xukuohai@huawei.com>
Link: https://lore.kernel.org/r/20260605140243.664590-2-xukuohai@huaweicloud.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
[airlied: just added some comments on how to reenable]
On-list because the cat is out of the bag and we're clearly not good
enough to figure this out in private. The story thus far:
5e28b7b94408 ("drm: Set old handle to NULL before prime swap in
change_handle") tried to fix a race condition between the gem_close and
gem_change_handle ioctls, but got a few things wrong:
- There's a confusion with the local variable handle, which is actually
the new handle, and so the two-stage trick was actually applied to the
wrong idr slot. 7164d78559b0 ("drm/gem: fix race between
change_handle and handle_delete") tried to fix that by adding yet
another code block, but forgot to add the error handling. Which meant
we now have two paths, both kinda wrong.
- dc366607c41c ("drm: Replace old pointer to new idr") tried to apply
another fix, but inconsistently, again because of the handle confusion
- this would be the right fix (kinda, somewhat, it's a mess) if we'd
do the two-stage approach for the new handle. Except that wasn't the
intent of the original fix.
We also didn't have an igt merged for the original ioctl, which is a big
no-go. This was attempted to address off-list in the original bugfix,
and amd QA people claimed the bug was fixed now. Very clearly that's not
the case. Here's my attempt to sort this out:
- Rename the local variable to new_handle, the old aliasing with
args->handle is just too dangerously confusing.
- Merge the gem obj lookup with the two-stage idr_replace so that we
avoid getting ourselves confused there.
- This means we don't have a surplus temporary reference anymore, only
an inherited from the idr. A concurrent gem_close on the new_handle
could steal that. Fix that with the same two-stage approach
create_tail uses. This is a bit overkill as documented in the comment,
but I also don't trust my ability to understand this all correctly, so
go with the established pattern we have from other ioctls instead for
maximum paranoia.
- Adjust error paths. I've tried to make the error and success paths
common, because they are identical except for which handle is removed
and on which we call idr_replace to (re)install the object again. But
that made things messier to read, so I've left it at the more verbose
version, which unfortunately hides the symmetry in the entire code
flow a bit.
- While at it, also replace the 7 space indent with 1 tab.
And finally, because I flat out don't trust my abilities here at all
anymore:
- Disable the ioctl until we have the igt situation and everything else
sorted out on-list and with full consensus.
v2:
Sashiko noticed that I didn't handle the error path for idr_replace
correctly, it must be checked with IS_ERR_OR_NULL like in
gem_handle_delete. So yeah, definitely should just the existing paths
1:1 because this is endless amounts of tricky.
Also add the Fixes: line for the original ioctl, I forgot that too.
Reported-by: DARKNAVY (@DarkNavyOrg) <vr@darknavy.com>
Signed-off-by: Simona Vetter <simona.vetter@ffwll.ch>
Fixes: dc366607c41c ("drm: Replace old pointer to new idr")
Cc: syzbot+d7c9eed171647e421013@syzkaller.appspotmail.com
Cc: stable@vger.kernel.org
Cc: Edward Adam Davis <eadavis@qq.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Fixes: 5e28b7b94408 ("drm: Set old handle to NULL before prime swap in change_handle")
Cc: David Francis <David.Francis@amd.com>
Cc: Puttimet Thammasaeng <pwn8official@gmail.com>
Cc: Christian Koenig <Christian.Koenig@amd.com>
Fixes: 7164d78559b0 ("drm/gem: fix race between change_handle and handle_delete")
Cc: Zhenghang Xiao <kipreyyy@gmail.com>
Fixes: 5e28b7b94408 ("drm: Set old handle to NULL before prime swap in change_handle")
Reviewed-by: David Francis <David.Francis@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patch.msgid.link/20260604194437.1725314-1-simona.vetter@ffwll.ch
|
|
'bpf-fix-sysctl-new-value-handling-in-__cgroup_bpf_run_filter_sysctl'
Dawei Feng says:
====================
bpf: fix sysctl new-value handling in __cgroup_bpf_run_filter_sysctl
This series fixes three bugs in the sysctl write-buffer replacement path
of __cgroup_bpf_run_filter_sysctl(). It resolves a kvzalloc()/kfree()
mismatch, adds a missing NUL terminator to the replacement string, and
updates a stale return value check to safely restore the replacement
functionality.
Patch Summary:
- patch 1 NUL-terminates the replaced sysctl value
- patch 2 uses kvfree() for the replaced sysctl write buffer
- patch 3 restores sysctl new-value replacement
Changelog:
v2 -> v3:
- reordered patches 1 and 2
- added the missing Reviewed-by/Acked-by tags to patches 2 and 3
- fixed the incorrect Fixes tag in patch 3
- simplified the dynamic test logs in patch 1 and 2, and updated
titles
====================
Link: https://patch.msgid.link/20260603105317.944304-1-dawei.feng@seu.edu.cn
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Commit 4e63acdff864 ("bpf: Introduce bpf_sysctl_{get,set}_new_value
helpers") changed the success return value to 0, but failed to update the
corresponding check in __cgroup_bpf_run_filter_sysctl(). Since
bpf_prog_run_array_cg() now returns 0 on success, the legacy ret == 1
condition is never satisfied. As a result, the modified value is ignored,
and bpf_sysctl_set_new_value() fails to replace the write buffer.
Fix this by checking for a return value of 0 instead, so cgroup/sysctl
programs can correctly replace the pending sysctl buffer.
This bug was discovered during a manual code review. Tested via a
cgroup/sysctl BPF reproducer overriding writes to a target sysctl.
Pre-fix, bpf_sysctl_set_new_value("foo") was silently ignored: the write
returned 8192 and the value remained "600". Post-fix, the BPF replacement
buffer properly propagates: the write returns 3 and the value updates to
"foo".
Fixes: f10d05966196 ("bpf: Make BPF_PROG_RUN_ARRAY return -err instead of allow boolean")
Cc: stable@vger.kernel.org
Acked-by: Yonghong Song <yonghong.song@linux.dev>
Signed-off-by: Zilin Guan <zilin@seu.edu.cn>
Signed-off-by: Dawei Feng <dawei.feng@seu.edu.cn>
Reviewed-by: Jiayuan Chen <jiayuan.chen@linux.dev>
Acked-by: Xu Kuohai <xukuohai@huawei.com>
Link: https://lore.kernel.org/r/20260603105317.944304-4-dawei.feng@seu.edu.cn
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
proc_sys_call_handler() allocates its temporary sysctl buffer with
kvzalloc() and passes it to __cgroup_bpf_run_filter_sysctl(). Since
kvzalloc() may fall back to vmalloc() for large allocations, freeing
that buffer with kfree() is wrong and can corrupt memory.
Use kvfree() to safely handle both kmalloc and kvzalloc()/vmalloc
allocations.
The bug was first flagged by an experimental analysis tool we are
developing for kernel memory-management bugs while analyzing
v6.13-rc1. The tool is still under development and is not yet publicly
available. Manual inspection confirms that the bug is still
present in v7.1-rc5.
Reproduced the bug based on v7.1-rc4 in a QEMU x86_64 guest booted with
KASAN and CONFIG_FAILSLAB enabled. To exercise the replacement path, the
test tree also included the accompanying fix for the stale ret == 1
check in __cgroup_bpf_run_filter_sysctl(). The reproducer confines
failslab injections to the proc_sys_call_handler() range, uses
stacktrace-depth=32, and injects fail-nth=1 while writing 8191 bytes to
/proc/sys/kernel/domainname from a task in the target cgroup. Under
that setup, fail-nth=1 triggered the fault:
BUG: unable to handle page fault for address: ffffeb0200024d48
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 0 P4D 0
Oops: Oops: 0000 SMP KASAN NOPTI
CPU: 2 UID: 0 PID: 209 Comm: repro_proc_sys_ Not tainted 7.1.0-rc4-00686-g97625979a5d4 PREEMPT(lazy)
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.15.0-1 04/01/2014
RIP: 0010:kfree+0x6e/0x510
...
Call Trace:
<TASK>
? __cgroup_bpf_run_filter_sysctl+0x626/0xc30
__cgroup_bpf_run_filter_sysctl+0x74d/0xc30
? __pfx___cgroup_bpf_run_filter_sysctl+0x10/0x10
? srso_return_thunk+0x5/0x5f
? __kvmalloc_node_noprof+0x345/0x870
? proc_sys_call_handler+0x250/0x480
? srso_return_thunk+0x5/0x5f
proc_sys_call_handler+0x3a2/0x480
? __pfx_proc_sys_call_handler+0x10/0x10
? srso_return_thunk+0x5/0x5f
? selinux_file_permission+0x39f/0x500
? srso_return_thunk+0x5/0x5f
? lock_is_held_type+0x9e/0x120
vfs_write+0x98e/0x1000
...
</TASK>
With this fix applied on top of the same test setup, rerunning the
reproducer with fail-nth=1 yields no corresponding Oops reports.
Fixes: 4508943794ef ("proc: use kvzalloc for our kernel buffer")
Cc: stable@vger.kernel.org
Reviewed-by: Emil Tsalapatis <emil@etsalapatis.com>
Reviewed-by: Jiayuan Chen <jiayuan.chen@linux.dev>
Acked-by: Yonghong Song <yonghong.song@linux.dev>
Signed-off-by: Zilin Guan <zilin@seu.edu.cn>
Signed-off-by: Dawei Feng <dawei.feng@seu.edu.cn>
Link: https://lore.kernel.org/r/20260603105317.944304-3-dawei.feng@seu.edu.cn
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
When writing to sysctls, proc_sys_call_handler() guarantees that the
buffer passed to proc handlers is NUL-terminated. If
bpf_sysctl_set_new_value() replaces the pending sysctl value, it can
hand a replacement buffer directly to proc handlers. However, the
helper currently copies only buf_len bytes into that buffer without
appending a NUL terminator, leaving downstream parsers vulnerable to
out-of-bounds access.
Fix this by appending a '\0' after the replaced value to restore the
expected sysctl semantics. Since the helper already rejects buf_len
greater than PAGE_SIZE - 1, there is always room for the extra byte.
Reproduced in a QEMU x86_64 guest booted with KASAN while exercising
the sysctl replacement path with a cgroup/sysctl BPF program. The
reproducer targets `/proc/sys/net/core/flow_limit_cpu_bitmap`, fills
the original user write buffer with non-zero bytes, and overrides the
sysctl value so the replacement buffer lacks a terminating NUL. Under
that setup, the pre-fix kernel reported:
BUG: KASAN: slab-out-of-bounds in strnchrnul+0x72/0x90
Read of size 1 at addr ffff88800de57000 by task repro_patch3/66
CPU: 0 UID: 0 PID: 66 Comm: repro_patch3 Not tainted 7.1.0-rc3-00269-g8370ca1f87cc #6 PREEMPT(lazy)
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1 04/01/2014
Call Trace:
<TASK>
dump_stack_lvl+0x68/0xa0
print_report+0xcb/0x5e0
? __virt_addr_valid+0x21d/0x3f0
? strnchrnul+0x72/0x90
? strnchrnul+0x72/0x90
kasan_report+0xca/0x100
? strnchrnul+0x72/0x90
strnchrnul+0x72/0x90
bitmap_parse+0x37/0x2e0
flow_limit_cpu_sysctl+0xc6/0x840
? __pfx_flow_limit_cpu_sysctl+0x10/0x10
? __kvmalloc_node_noprof+0x5ba/0x870
proc_sys_call_handler+0x31d/0x480
? __pfx_proc_sys_call_handler+0x10/0x10
? selinux_file_permission+0x39f/0x500
? lock_is_held_type+0x9e/0x120
vfs_write+0x98e/0x1000
...
</TASK>
The buggy address is located 0 bytes to the right of
allocated 4096-byte region [ffff88800de56000, ffff88800de57000)
With this fix applied, rerunning the same sysctl-targeted path yields
no corresponding KASAN reports.
Signed-off-by: Zilin Guan <zilin@seu.edu.cn>
Signed-off-by: Dawei Feng <dawei.feng@seu.edu.cn>
Acked-by: Yonghong Song <yonghong.song@linux.dev>
Link: https://lore.kernel.org/r/20260603105317.944304-2-dawei.feng@seu.edu.cn
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
https://gitlab.freedesktop.org/drm/i915/kernel into drm-fixes
- Fix color blob reference handling in intel_plane_state (Chaitanya Kumar Borah)
- Revert "drm/i915/backlight: Remove try_vesa_interface" [backlight] (Suraj Kandpal)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Tvrtko Ursulin <tursulin@igalia.com>
Link: https://patch.msgid.link/aiKgmwz7VGOaFXIv@linux
|
|
https://gitlab.freedesktop.org/drm/misc/kernel into drm-fixes
Short summary of fixes pull:
dumb-buffer:
- remove strict limits on buffer geometry
ethosu:
- reject unsupported NPU_OP_RESIZE
- fix index of IFM region
- fix weight index
- fix overflows in DMA-size calculations
- reject DMA commands with uninitialized length
- fix OOB write in ethosu_gem_cmdstream_copy_and_validate
imx:
- fix kernel-doc warnings
ivpu:
- add overflow checks in firmware handling and get_info_ioctl
v3d:
- wait for pending L2T flush before cleaning caches
- fix leak of vaddr
- skip CSD when it has zeroed workgroups
- fix ref counting in performance monitoring
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patch.msgid.link/20260605072602.GA268798@linux.fritz.box
|
|
Leon Hwang says:
====================
bpf: Update transport_header when encapsulating UDP tunnel in lwt
Currently, bpf_lwt_push_ip_encap() does not update skb->transport_header.
When a driver, e.g. ice, reuses the stale skb->transport_header to
offload checksum computation to NIC hardware, VxLAN packets encapsulated
by bpf_lwt_push_encap() helper may be dropped due to incorrect checksum.
Update skb->transport_header in bpf_lwt_push_ip_encap() whenever the
encapsulated packet uses UDP, so checksum offload works correctly.
Changes:
v3 -> v4:
* Address comments from Emil:
* Make the logic of skb_set_transport_header() clearer in patch #1.
* Fold the code of fexit_lwt_push_ip_encap() into test_lwt_ip_encap.c in
patch #2.
* Resolve assorted issues of test in patch #2.
* v3: https://lore.kernel.org/bpf/20260601150203.20352-1-leon.hwang@linux.dev/
v2 -> v3:
* Drop patch #1 and #2 of v2 that aim to resolve potential issues
reported by sashiko (per Alexei).
* Check target IP version and UDP tunnel in test (per sashiko).
* v2: https://lore.kernel.org/bpf/20260529151351.69911-1-leon.hwang@linux.dev/
v1 -> v2:
* Address sashiko's reviews:
* Fix TOCTOU issue in lwt to avoid changing hdr after checks.
* Add check iph->ihl < 5 in lwt to avoid infinite-loop in MIPS driver.
* Update comment style in selftests with BPF comment style.
* v1: https://lore.kernel.org/bpf/20260525142650.2569-1-leon.hwang@linux.dev/
====================
Link: https://patch.msgid.link/20260602150931.49629-1-leon.hwang@linux.dev
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Add two tests to verify the transport header of skb has been set when
encapsulate VxLAN using bpf_lwt_push_encap() helper.
1. VxLAN over IPv4.
2. VxLAN over IPv6.
Without the fix, the tests would fail:
lwt_ip_encap_vxlan:FAIL:transport_hdr offset unexpected transport_hdr offset: actual 70 != expected 20
#208 lwt_ip_encap_vxlan_ipv4:FAIL
lwt_ip_encap_vxlan:FAIL:transport_hdr offset unexpected transport_hdr offset: actual 110 != expected 40
#209 lwt_ip_encap_vxlan_ipv6:FAIL
The unexpected offsets are: outer encap headers
(IPv4: iphdr+udp+vxlan+eth = 50 bytes, IPv6: ipv6hdr+udp+vxlan+eth = 70 bytes)
plus the inner IP header (20 or 40 bytes), because without the fix
transport_header still points at the inner transport layer instead of the
outer UDP header.
Assisted-by: Claude:claude-sonnet-4-6
Cc: Leon Hwang <leon.huangfu@shopee.com>
Signed-off-by: Leon Hwang <leon.hwang@linux.dev>
Link: https://lore.kernel.org/r/20260602150931.49629-3-leon.hwang@linux.dev
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Currently, bpf_lwt_push_ip_encap() does not update skb->transport_header.
When a driver, e.g. ice, reuses the stale skb->transport_header to
offload checksum computation to NIC hardware, VxLAN packets encapsulated
by bpf_lwt_push_encap() helper may be dropped due to incorrect checksum.
Update skb->transport_header in bpf_lwt_push_ip_encap() whenever the
encapsulated packet uses UDP, so checksum offload works correctly.
Fixes: 52f278774e79 ("bpf: implement BPF_LWT_ENCAP_IP mode in bpf_lwt_push_encap")
Cc: Leon Hwang <leon.huangfu@shopee.com>
Signed-off-by: Leon Hwang <leon.hwang@linux.dev>
Link: https://lore.kernel.org/r/20260602150931.49629-2-leon.hwang@linux.dev
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Varun R Mallya says:
====================
RISC-V JIT support for bpf_get_current_task/_btf
These two patches add support for the bpf_get_current_task and
bpf_get_current_task_btf kfuncs in RISC-V JIT and add a selftest.
The first patch adds support for cpu and feature detection on
the JIT disassembly helper function as RISC-V JITed code was not
being disassembled using `LLVMCreateDisasm` as it was missing the
"+c" CPU feature and JITed code contained RISC-V Compressed (C)
Extension. This patch generalizes that to detect CPU features and
enables testing on more RISC-V JIT work ahead.
The second patch, which actually adds this support has been benchmarked
on QEMU RISC-V and shows significant improvements.
It was benchmarked using a simple loop inside a bpf program that ran
bpf_get_current_task() and execution time was measured. It used
bpf_prog_test_run_opts() to repeatedly trigger the BPF program. The loop
ran in 1 second intervals and it kept firing bpf_prog_test_run_opts() as
fast as possible until a second had elapsed and then reported statistics.
====================
Link: https://patch.msgid.link/20260602205847.102825-1-varunrmallya@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
