| Age | Commit message (Collapse) | Author |
|---|
|
There is no need to pre-initialise the rk3528 RMII clock when
selecting RMII mode on gmac0.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1vmqn1-00000007VCh-47Sv@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Update rk_set_reg_speed() to use either the grf or php_grf regmap
depending on the SoC's requirements and convert rk3588, removing
its custom code.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1vmqmw-00000007VCb-3glG@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Move the speed/clocking related GRF register offset into the driver
private data, convert rk_set_reg_speed() to use it and initialise this
member either from the corresponding member in struct rk_gmac_ops, or
the SoC specific initialisation function.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1vmqmr-00000007VCV-3Cz8@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
rk3588 has a quirk compared to the other Rockchip implementations in
that the interface mode configuration register is in the php_grf
regmap rather than the grf regmap. Add a flag to indicate this, and
a separate function to write to the appropriate regmap. This allows
rk3588 to be converted.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1vmqmm-00000007VCP-2XZc@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The majority of Rockchip implementations require three common pieces
of information to configure the PHY interface mode:
- The grf register offset for configuring the GMAC phy_intf_sel field
and the RMII mode bit.
- The bitfield in this register for the GMAC's phy_intf_sel.
- The bit position for RMII mode but clear for RGMII mode.
Introduce members for this information into struct rk_priv_data and
struct rk_gmac_ops, which will be used to pre-initialise the struct
rk_priv_data members. We describe the register contents using
bitfields, even for those that are a single bit for consistency.
As each register comprises of two halves, where the upper half enables
changing the bit state in the lower half, we can describe these
bitfields using a 16-bit data type, and provide rk_encode_wm16() to
generate the actual register values from the field mask and field
value. We are unable to use the FIELD_PREP_WM16() macros for this as
these require the field mask to be a constant.
Add code to rk_gmac_powerup() to get the phy_intf_sel value, validating
that the resulting mode is either RMII or RGMII. No other modes are
supported by any of the Rockchip SoCs supported by this driver.
If either of the bitfield mask values are populated in struct
rk_priv_data, use these to generate the register contents, and write
the resulting value to the specified GRF register.
Convert many Rockchip implementations to use this new infrastructure.
For those where there is a single GMAC instance, it is merely a case of
filling in the new members of struct rk_gmac_ops. For those with
multiple instances, one or more of these members depends on the GMAC
instance, so setup of the members in struct rk_gmac has to be done via
the .init method of struct rk_gmac_ops. The corresponding code is
removed from the set_to_rgmii() and set_to_rmii() implementations.
Since the member name documents the purpose of the field that is being
initialised, providing preprocessor macros to define the bitfields is
deemed to be less than useful given the massive size of this driver.
The existing mechanisms remain behind for those SoCs that can not be
converted to this scheme.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
v2: disable clocks on failure
Link: https://patch.msgid.link/E1vmqmh-00000007VCJ-1xns@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Set up global DSCP/PCP priority mappings and add related DCB methods.
Signed-off-by: David Yang <mmyangfl@gmail.com>
Link: https://patch.msgid.link/20260131021854.3405036-6-mmyangfl@gmail.com
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
yt921x_chip_setup() is already pretty long, and is going to become
longer. Split it into parts.
Signed-off-by: David Yang <mmyangfl@gmail.com>
Link: https://patch.msgid.link/20260131021854.3405036-5-mmyangfl@gmail.com
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Create a helper function to centralize the logic for enabling and
disabling VLAN awareness on a port.
Signed-off-by: David Yang <mmyangfl@gmail.com>
Link: https://patch.msgid.link/20260131021854.3405036-4-mmyangfl@gmail.com
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Not pausing it means that we can have the TCM work queued into a
non-freezable workqueue, which, in resume, is re-activated before the
driver's resume is called.
The TCM work might send commands to the FW before we resumed the device,
leading to an assert.
Closes: https://lore.kernel.org/linux-wireless/aTDoDiD55qlUZ0pn@debian.local/
Tested-by: Chris Bainbridge <chris.bainbridge@gmail.com>
Fixes: e8bb19c1d590 ("wifi: iwlwifi: support fast resume")
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260129212650.05621f3faedb.I44df9cf9183b5143df8078131e0d87c0fd7e1763@changeid
|
|
mlo_scan_start_wk is not canceled on disconnection. In fact, it is not
canceled anywhere except in the restart cleanup, where we don't really
have to.
This can cause an init-after-queue issue: if, for example, the work was
queued and then drv_change_interface got executed.
This can also cause use-after-free: if the work is executed after the
vif is freed.
Fixes: 9748ad82a9d9 ("wifi: iwlwifi: defer MLO scan after link activation")
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260129212650.a36482a60719.I5bf64a108ca39dacb5ca0dcd8b7258a3ce8db74c@changeid
|
|
wlc_phy_txpwr_srom_read_lcnphy() in wlc_phy_attach_lcnphy() always
returns true, making the error handling code unreachable. Change the
function's return type to void and remove the dead code, similar to
the cleanup done for wlc_phy_txpwr_srom_read_nphy() in commit
47f0e32ffe4e ("wifi: brcmsmac: phy: Remove unreachable code").
Signed-off-by: Ingyu Jang <ingyujang25@korea.ac.kr>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Link: https://patch.msgid.link/20260131172355.3367673-1-ingyujang25@korea.ac.kr
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Last user dsa_loop has been migrated away from modalias-based matching,
so we can remove this feature now. It was the only user of MDIO_NAME_SIZE,
so remove also this constant.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/ce1c6df0-4785-4b28-8322-32dc6bceea18@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
This change is a prerequisite for removing the MDIO device modalias,
as dsa_loop is the only user. Switch from modalias to a custom
bus match function.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/15a4318f-50b5-4df5-874e-e387ee070a9d@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Primary reason for this change is to remove the misuse of MDIO_NAME_SIZE
here, so that this constant can be removed in a follow-up patch.
Use case here is simply a chip name w/o any relationship to a MDIO
device. Also there's no need to reserve a longer char array, so make
the name a pointer.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/61bc14fa-eed3-43b6-ae40-b98063e81578@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The dwmac core has no support for SGMII without using its integrated
PCS. Thus, PHY_INTF_SEL_SGMII is only supported when this block is
present, and it makes no sense for stmmac_get_phy_intf_sel() to decode
this.
None of the platform glue users that use stmmac_get_phy_intf_sel()
directly accept PHY_INTF_SEL_SGMII as a valid mode.
Check whether a PCS will be used by the driver for the interface mode,
and if it is the integrated PCS, query the integrated PCS for the
phy_intf_sel_i value to use.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Tested-by: Mohd Ayaan Anwar <mohd.anwar@oss.qualcomm.com>
Link: https://patch.msgid.link/E1vlmOa-00000006zvB-1fIe@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Move most of the PCS register offset definitions to stmmac_pcs.c.
Since stmmac_pcs.c only ever passes zero into the register offset
macros, remove that ability, making them simple constant integer
definitions.
Add appropriate descriptions of the registers, pointing out their
similarity with their IEEE 802.3 counterparts. Make use of the
BMSR definitions for the GMAC_AN_STATUS register and remove the
driver private versions.
Note that BMSR_LSTATUS is non-low-latching, unlike it's 802.3z
counterpart.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Tested-by: Mohd Ayaan Anwar <mohd.anwar@oss.qualcomm.com>
Link: https://patch.msgid.link/E1vlmOV-00000006zv5-1CwO@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Where a core supports hardware features, but does not indicate support
for half-duplex, clear phylink's half-duplex 1G, 100M and 10M
capability bits to disallow half-duplex operation and advertisement of
these link modes.
This will avoid the need for special code in the PCS driver to do this
based on the ESTATUS register bits, as the support in the PCS is
dependent on the same synthesis choice as the MAC core.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Mohd Ayaan Anwar <mohd.anwar@oss.qualcomm.com>
Link: https://patch.msgid.link/E1vlmOQ-00000006zuz-0ffN@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The driver never programs the MAC frame size and jabber registers,
causing the hardware to reject frames larger than the default 1518
bytes even when larger DMA buffers are allocated.
Program MAC_MAXIMUM_FRAME_SIZE, MAC_TRANSMIT_JABBER_SIZE, and
MAC_RECEIVE_JABBER_SIZE based on the configured MTU. Also fix the
maximum buffer size from 4096 to 4095, since the descriptor buffer
size field is only 12 bits. Account for double VLAN tags in frame
size calculations.
Fixes: bfec6d7f2001 ("net: spacemit: Add K1 Ethernet MAC")
Cc: stable@vger.kernel.org
Signed-off-by: Tomas Hlavacek <tmshlvck@gmail.com>
Link: https://patch.msgid.link/20260130102301.477514-1-tmshlvck@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Compared to other Renesas GBETH stmmac glue drivers, RZ/G3L GBETH IP use
the version Synopsys DesignWare MAC (version 5.30). It has an extra clock
compared to RZ/V2H and has ptp_pps_o interrupts. Add support for RZ/G3L
GBETH by reusing device data of RZ/V2H and can be extended to add other
functionalities later.
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://patch.msgid.link/20260131161250.5047-3-biju.das.jz@bp.renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2026-01-30 (ice, i40e)
This series contains updates to ice and i40e drivers.
Grzegorz and Jake resolve issues around timing for E825 that can cause Tx
timestamps to be missed/interrupts not generated on ice.
Aaron Ma defers restart of PTP work until after after VSIs are rebuilt
to prevent NULL pointer dereference for ice.
Mohammad Heib removes calls to udp_tunnel_get_rx_info() in ice and i40e
which violates locking expectations and is unneeded.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
i40e: drop udp_tunnel_get_rx_info() call from i40e_open()
ice: drop udp_tunnel_get_rx_info() call from ndo_open()
ice: Fix PTP NULL pointer dereference during VSI rebuild
ice: PTP: fix missing timestamps on E825 hardware
ice: fix missing TX timestamps interrupts on E825 devices
====================
Link: https://patch.msgid.link/20260130185401.1091523-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
It is not recommended to access the 32‑bit registers of this hardware IP
using lower‑width accessors (i.e. 16‑bit), and the only exception to
this rule was introduced in the initial ENETC v1 driver for the PMAR1
register, which holds the lower 16 bits of the primary MAC address of
an SI. Meanwhile, this exception has been replicated in the v4 driver
code as well.
Since LS1028 (the only SoC with ENETC v1) is not affected by this issue,
the current patch converts the 16‑bit reads from PMAR1 starting with
ENETC v4.
Fixes: 99100d0d9922 ("net: enetc: add preliminary support for i.MX95 ENETC PF")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Link: https://patch.msgid.link/20260130141035.272471-5-claudiu.manoil@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
For ENETC v4, which is integrated into more complex SoCs (compared to v1),
16‑bit register writes are blocked in the SoC interconnect on some chips.
To be fair, it is not recommended to access 32‑bit registers of this IP
using lower‑width accessors (i.e. 16‑bit), and the only exception to
this rule was introduced by me in the initial ENETC v1 driver for the
PMAR1 register, which holds the lower 16 bits of the primary MAC address
of an SI. Meanwhile, this exception has been replicated for v4 as well.
Since LS1028 (the only SoC with ENETC v1) is not affected by this issue,
the current patch fixes the 16‑bit writes to PMAR1 starting with ENETC
v4.
Fixes: 99100d0d9922 ("net: enetc: add preliminary support for i.MX95 ENETC PF")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Link: https://patch.msgid.link/20260130141035.272471-4-claudiu.manoil@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
For ENETC v4 these settings are controlled by the global ENETC
command cache attribute registers (EnCAR), from the IERB register
block.
The hardcoded CDBR cacheability settings were inherited from LS1028A,
and should be removed from the ENETC v4 driver as they conflict
with the global IERB settings.
Fixes: e3f4a0a8ddb4 ("net: enetc: add command BD ring support for i.MX95 ENETC")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Link: https://patch.msgid.link/20260130141035.272471-3-claudiu.manoil@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
For ENETC v4 these settings are controlled by the global ENETC
message and buffer cache attribute registers (EnBCAR and EnMCAR),
from the IERB register block.
The hardcoded cacheability settings were inherited from LS1028A,
and should be removed from the ENETC v4 driver as they conflict
with the global IERB settings.
Fixes: 99100d0d9922 ("net: enetc: add preliminary support for i.MX95 ENETC PF")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Link: https://patch.msgid.link/20260130141035.272471-2-claudiu.manoil@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Many network drivers have unnecessary empty module_init and module_exit
functions. Remove them (including some that just print a message). Note
that if a module_init function exists, a module_exit function must also
exist; otherwise, the module cannot be unloaded.
Signed-off-by: Ethan Nelson-Moore <enelsonmoore@gmail.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Link: https://patch.msgid.link/20260131004327.18112-1-enelsonmoore@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The module version is useless, and the only thing these drivers' init
routines did besides pci_register_driver was to print the driver name
and/or version.
Acked-by: Francois Romieu <romieu@fr.zoreil.com> (epic100)
Reviewed-by: Simon Horman <horms@kernel.org> (epic100, sis900)
Reviewed-by: Sai Krishna <saikrishnag@marvell.com> (epic100)
Signed-off-by: Ethan Nelson-Moore <enelsonmoore@gmail.com>
Link: https://patch.msgid.link/20260131022441.56274-1-enelsonmoore@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If the board designers have neglected to populate the appropriate
resistors on the strapping pins then the phy may default to the wrong
interface mode. Enable/disable the RGMII/SGMII enable bits as necessary
to select the correct interface.
The dp83867 strapping pins have four levels and typically configure two
features at once. LED_0 controls both port mirroring and whether SGMII
is enabled. If it is pulled to VDDIO, both port mirroring and SGMII
will be enabled. For variants of the dp83867 that do not support SGMII,
this will prevent data from being transferred. As we now explicitly set
the SGMII and RGMII enable bits, we do not need to detect whether SGMII
has been inadvertently enabled.
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Link: https://patch.msgid.link/20260129171205.3868605-3-sean.anderson@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
All supported interfaces use the TX FIFO register at least some of the
time, so there's no point in checking the interface. Retain the check
for the RX FIFO level since it is only used by SGMII.
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Link: https://patch.msgid.link/20260129171205.3868605-2-sean.anderson@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Marek reported that suspending stm32 causes the following errors when
the interface is administratively down:
$ echo devices > /sys/power/pm_test
$ echo mem > /sys/power/state
...
ck_ker_eth2stp already disabled
...
ck_ker_eth2stp already unprepared
...
On suspend, stm32 starts the eth2stp clock in its suspend method, and
stops it in the resume method. This is because the blamed commit omits
the call to the platform glue ->suspend() method, but does make the
call to the platform glue ->resume() method.
This problem affects all other converted drivers as well - e.g. looking
at the PCIe drivers, pci_save_state() will not be called, but
pci_restore_state() will be. Similar issues affect all other drivers.
Fix this by always calling the ->suspend() method, even when the network
interface is down. This fixes all the conversions to the platform glue
->suspend() and ->resume() methods.
Link: https://lore.kernel.org/r/20260114081809.12758-1-marex@nabladev.com
Fixes: 07bbbfe7addf ("net: stmmac: add suspend()/resume() platform ops")
Reported-by: Marek Vasut <marex@nabladev.com>
Tested-by: Marek Vasut <marex@nabladev.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1vlujh-00000007Hkw-2p6r@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
It appears that in commit 7efd79c0e689 ("bnxt_en: Add drop action
support for ntuple"), bnxt gained support for ntuple filters for packet
drops.
However, support for this does not seem to work in recent kernels or
against net-next:
% sudo ethtool -U eth0 flow-type udp4 src-ip 1.1.1.1 action -1
rmgr: Cannot insert RX class rule: Operation not supported
Cannot insert classification rule
The issue is that the existing code uses ethtool_get_flow_spec_ring_vf,
which will return a non-zero value if the ring_cookie is set to
RX_CLS_FLOW_DISC, which then causes bnxt_add_ntuple_cls_rule to return
-EOPNOTSUPP because it thinks the user is trying to set an ntuple filter
for a vf.
Fix this by first checking that the ring_cookie is not RX_CLS_FLOW_DISC.
After this patch, ntuple filters for drops can be added:
% sudo ethtool -U eth0 flow-type udp4 src-ip 1.1.1.1 action -1
Added rule with ID 0
% ethtool -n eth0
44 RX rings available
Total 1 rules
Filter: 0
Rule Type: UDP over IPv4
Src IP addr: 1.1.1.1 mask: 0.0.0.0
Dest IP addr: 0.0.0.0 mask: 255.255.255.255
TOS: 0x0 mask: 0xff
Src port: 0 mask: 0xffff
Dest port: 0 mask: 0xffff
Action: Drop
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Joe Damato <joe@dama.to>
Link: https://patch.msgid.link/20260131003042.2570434-1-joe@dama.to
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Print the PHY driver used and interrupt status after connection.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20260201100001.33102-1-amadeus@jmu.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ath/ath
Jeff Johnson says:
==================
ath.git patches for v6.20/v7.0 (#3)
A set of small features and cleanups for the next merge window.
==================
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Pink-Ke Shih says:
==================
rtw-next patches for -next
Mainly refactor flow for preparation of rtw89 RTL8922DE. Others are random
fixes and refinements.
==================
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2026-01-31
This first 2 patches are by Biju Das, target the rcar_canfd driver and
add support for FD-only mode.
Lad Prabhakar's patches, also for the rcar_canfd driver add support
for the RZ/T2H SoC.
The last 2 patches are by Michael Tretter and me, target the sja1000
driver and clean up the CAN state handling.
* tag 'linux-can-next-for-6.20-20260131' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next:
can: sja1000: sja1000_err(): use error counter for error state
can: sja1000: sja1000_err(): make use of sja1000_get_berr_counter() to read error counters
can: rcar_canfd: Add RZ/T2H support
dt-bindings: can: renesas,rcar-canfd: Document RZ/T2H and RZ/N2H SoCs
dt-bindings: can: renesas,rcar-canfd: Document RZ/V2H(P) and RZ/V2N SoCs
dt-bindings: can: renesas,rcar-canfd: Specify reset-names
can: rcar_canfd: Add support for FD-Only mode
dt-bindings: can: renesas,rcar-canfd: Document renesas,fd-only property
====================
Link: https://patch.msgid.link/20260131101512.1958907-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
rtl8152 can trigger device reset during reset which
potentially can result in a deadlock:
**** DPM device timeout after 10 seconds; 15 seconds until panic ****
Call Trace:
<TASK>
schedule+0x483/0x1370
schedule_preempt_disabled+0x15/0x30
__mutex_lock_common+0x1fd/0x470
__rtl8152_set_mac_address+0x80/0x1f0
dev_set_mac_address+0x7f/0x150
rtl8152_post_reset+0x72/0x150
usb_reset_device+0x1d0/0x220
rtl8152_resume+0x99/0xc0
usb_resume_interface+0x3e/0xc0
usb_resume_both+0x104/0x150
usb_resume+0x22/0x110
The problem is that rtl8152 resume calls reset under
tp->control mutex while reset basically re-enters rtl8152
and attempts to acquire the same tp->control lock once
again.
Reset INACCESSIBLE device outside of tp->control mutex
scope to avoid recursive mutex_lock() deadlock.
Fixes: 4933b066fefb ("r8152: If inaccessible at resume time, issue a reset")
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Link: https://patch.msgid.link/20260129031106.3805887-1-senozhatsky@chromium.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
For MHI WWAN device, we need a match between NMEA channel and
WWAN_PORT_NMEA type. Then the GNSS subsystem could create the
gnss device succssfully.
Signed-off-by: Slark Xiao <slark_xiao@163.com>
Reviewed-by: Loic Poulain <loic.poulain@oss.qualcomm.com>
Link: https://patch.msgid.link/20260126062158.308598-9-slark_xiao@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Support NMEA port emulation for the WWAN core GNSS port testing purpose.
Emulator produces pair of GGA + RMC sentences every second what should
be enough to fool gpsd into believing it is working with a NMEA GNSS
receiver.
If the GNSS system is enabled then one NMEA port will be created
automatically for the simulated WWAN device. Manual NMEA port creation
is not supported at the moment.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Reviewed-by: Loic Poulain <loic.poulain@oss.qualcomm.com>
Link: https://patch.msgid.link/20260126062158.308598-8-slark_xiao@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Just introduced WWAN NMEA port type needs a testing option. The WWAN HW
simulator was developed with the AT port type in mind and cannot be
easily extended. Refactor it now to make it capable to support more port
types.
No big functional changes, mostly renaming with a little code
rearrangement.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Reviewed-by: Loic Poulain <loic.poulain@oss.qualcomm.com>
Link: https://patch.msgid.link/20260126062158.308598-7-slark_xiao@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Many WWAN modems come with embedded GNSS receiver inside and have a
dedicated port to output geopositioning data. On the one hand, the
GNSS receiver has little in common with WWAN modem and just shares a
host interface and should be exported using the GNSS subsystem. On the
other hand, GNSS receiver is not automatically activated and needs a
generic WWAN control port (AT, MBIM, etc.) to be turned on. And a user
space software needs extra information to find the control port.
Introduce the new type of WWAN port - NMEA. When driver asks to register
a NMEA port, the core allocates common parent WWAN device as usual, but
exports the NMEA port via the GNSS subsystem and acts as a proxy between
the device driver and the GNSS subsystem.
From the WWAN device driver perspective, a NMEA port is registered as a
regular WWAN port without any difference. And the driver interacts only
with the WWAN core. From the user space perspective, the NMEA port is a
GNSS device which parent can be used to enumerate and select the proper
control port for the GNSS receiver management.
CC: Slark Xiao <slark_xiao@163.com>
CC: Muhammad Nuzaihan <zaihan@unrealasia.net>
CC: Qiang Yu <quic_qianyu@quicinc.com>
CC: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
CC: Johan Hovold <johan@kernel.org>
Suggested-by: Loic Poulain <loic.poulain@oss.qualcomm.com>
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Reviewed-by: Loic Poulain <loic.poulain@oss.qualcomm.com>
Link: https://patch.msgid.link/20260126062158.308598-6-slark_xiao@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Upcoming GNSS (NMEA) port type support requires exporting it via the
GNSS subsystem. On another hand, we still need to do basic WWAN core
work: call the port stop operation, purge queues, release the parent
WWAN device, etc. To reuse as much code as possible, split the port
unregistering function into the deregistration of a regular WWAN port
device, and the common port tearing down code.
In order to keep more code generic, break the device_unregister() call
into device_del() and put_device(), which release the port memory
uniformly.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Reviewed-by: Loic Poulain <loic.poulain@oss.qualcomm.com>
Link: https://patch.msgid.link/20260126062158.308598-5-slark_xiao@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Upcoming GNSS (NMEA) port type support requires exporting it via the
GNSS subsystem. On another hand, we still need to do basic WWAN core
work: find or allocate the WWAN device, make it the port parent, etc. To
reuse as much code as possible, split the port creation function into
the registration of a regular WWAN port device, and basic port struct
initialization.
To be able to use put_device() uniformly, break the device_register()
call into device_initialize() and device_add() and call device
initialization earlier.
While at it, fix a minor number leak upon WWAN port registration
failure.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Link: https://patch.msgid.link/20260126062158.308598-4-slark_xiao@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We need information about existing WWAN device children since we remove
the device after removing the last child. Previously, we tracked users
implicitly by checking whether ops was registered and existence of a
child device of the wwan_class class. Upcoming GNSS (NMEA) port type
support breaks this approach by introducing a child device of the
gnss_class class.
And a modem driver can easily trigger a kernel Oops by removing regular
(e.g., MBIM, AT) ports first and then removing a GNSS port. The WWAN
device will be unregistered on removal of a last regular WWAN port. And
subsequent GNSS port removal will cause NULL pointer dereference in
simple_recursive_removal().
In order to support ports of classes other than wwan_class, switch to
explicit references counting. Introduce a dedicated counter to the WWAN
device struct, increment it on every wwan_create_dev() call, decrement
on wwan_remove_dev(), and actually unregister the WWAN device when there
are no more references.
Run tested with wwan_hwsim with NMEA support patches applied and
different port removing sequences.
Reported-by: Daniele Palmas <dnlplm@gmail.com>
Closes: https://lore.kernel.org/netdev/CAGRyCJE28yf-rrfkFbzu44ygLEvoUM7fecK1vnrghjG_e9UaRA@mail.gmail.com/
Suggested-by: Loic Poulain <loic.poulain@oss.qualcomm.com>
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Link: https://patch.msgid.link/20260126062158.308598-3-slark_xiao@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
It was used initially for a port id allocation, then removed, and then
accidently introduced again, but it is still unused. Drop it again to
keep code clean.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Reviewed-by: Loic Poulain <loic.poulain@oss.qualcomm.com>
Link: https://patch.msgid.link/20260126062158.308598-2-slark_xiao@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add debugfs hooks to display tx/rx rings for each napi
vector.
Note that the cloning mechanism in fbnic_ethtool.c for configuration
changes protects against concurrency issues with simultaneous config
changes along with debugs ring accesses.
The configuration switch builds up the new configuration offline,
takes the current config down, which removes the debugfs nv files, and
switches to the new configuration. The new configuration is brought
up which brings the debugfs files back on top of the new configuration
rings.
The interaction with fbnic_queue_stop() and fbnic_queue_start() will
similarly delete and add the files for the indicated vector.
Signed-off-by: Mike Marciniszyn (Meta) <mike.marciniszyn@gmail.com>
Link: https://patch.msgid.link/20260127200644.11640-3-mike.marciniszyn@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This patch adds reporting the Rx and Tx information
interfacing with the firmware.
The result of reading fbnic/fw_mbx is:
Rx
Rdy: 1 Head: 11 Tail: 10
Idx Len E Addr F H Raw
----------------------------------
00 4096 0 000101fea000 0 1 1000000101fea001
01 4096 0 000101feb000 0 1 1000000101feb001
.
.
.
15 4096 0 000101fe9000 0 1 1000000101fe9001
Tx
Rdy: 1 Head: 4 Tail: 4
Idx Len E Addr F H Raw
----------------------------------
00 0004 1 00010321b000 1 1 000440010321b003
01 0004 1 00010228d000 1 1 000440010228d003
.
.
.
15 0004 1 00010321b000 1 1 000440010321b003
Signed-off-by: Mike Marciniszyn (Meta) <mike.marciniszyn@gmail.com>
Link: https://patch.msgid.link/20260127200644.11640-2-mike.marciniszyn@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Many USB network drivers define get_drvinfo functions which add no
value over usbnet_get_drvinfo, only setting the driver name and
version. usbnet_get_drvinfo automatically sets the driver name, and
separate driver versions are now frowned upon in the kernel. Remove all
driver versions and replace these get_drvinfo functions with references
to usbnet_get_drvinfo where possible. Where that is not possible,
remove unnecessary code to set the driver name. Also remove two
unnecessary initializations from aqc111_get_drvinfo, an inaccurate
comment in pegasus.c, and an unused macro in catc.c.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Peter Korsgaard <peter@korsgaard.com> (for dm9601.c)
Signed-off-by: Ethan Nelson-Moore <enelsonmoore@gmail.com>
Link: https://patch.msgid.link/20260129042435.13395-2-enelsonmoore@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Correct spelling as flagged by codespell.
Signed-off-by: Simon Horman <horms@kernel.org>
Reviewed-by: Joe Damato <joe@dama.to>
Link: https://patch.msgid.link/20260129-stmmac-spell-v1-1-c7df9a96e482@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
valis provided a nice repro to crash the kernel:
ip link add p1 type veth peer p2
ip link set address 00:00:00:00:00:20 dev p1
ip link set up dev p1
ip link set up dev p2
ip link add mv0 link p2 type macvlan mode source
ip link add invalid% link p2 type macvlan mode source macaddr add 00:00:00:00:00:20
ping -c1 -I p1 1.2.3.4
He also gave a very detailed analysis:
<quote valis>
The issue is triggered when a new macvlan link is created with
MACVLAN_MODE_SOURCE mode and MACVLAN_MACADDR_ADD (or
MACVLAN_MACADDR_SET) parameter, lower device already has a macvlan
port and register_netdevice() called from macvlan_common_newlink()
fails (e.g. because of the invalid link name).
In this case macvlan_hash_add_source is called from
macvlan_change_sources() / macvlan_common_newlink():
This adds a reference to vlan to the port's vlan_source_hash using
macvlan_source_entry.
vlan is a pointer to the priv data of the link that is being created.
When register_netdevice() fails, the error is returned from
macvlan_newlink() to rtnl_newlink_create():
if (ops->newlink)
err = ops->newlink(dev, ¶ms, extack);
else
err = register_netdevice(dev);
if (err < 0) {
free_netdev(dev);
goto out;
}
and free_netdev() is called, causing a kvfree() on the struct
net_device that is still referenced in the source entry attached to
the lower device's macvlan port.
Now all packets sent on the macvlan port with a matching source mac
address will trigger a use-after-free in macvlan_forward_source().
</quote valis>
With all that, my fix is to make sure we call macvlan_flush_sources()
regardless of @create value whenever "goto destroy_macvlan_port;"
path is taken.
Many thanks to valis for following up on this issue.
Fixes: aa5fd0fb7748 ("driver: macvlan: Destroy new macvlan port if macvlan_common_newlink failed.")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: valis <sec@valis.email>
Reported-by: syzbot+7182fbe91e58602ec1fe@syzkaller.appspotmail.com
Closes: https: //lore.kernel.org/netdev/695fb1e8.050a0220.1c677c.039f.GAE@google.com/T/#u
Cc: Boudewijn van der Heide <boudewijn@delta-utec.com>
Link: https://patch.msgid.link/20260129204359.632556-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add the support to read the rx alignment errors and update
them in the standard rtnl_link_stats64 structure.
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20260129111520.1567097-1-Raju.Rangoju@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit fd580c9830316eda ("net: sfp: augment SFP parsing with
phy_interface_t bitmap") did not add augumentation for the interface
bitmap in the quirk for Ubiquiti U-Fiber Instant.
The subsequent commit f81fa96d8a6c7a77 ("net: phylink: use
phy_interface_t bitmaps for optical modules") then changed phylink code
for selection of SFP interface: instead of using link mode bitmap, the
interface bitmap is used, and the fastest interface mode supported by
both SFP module and MAC is chosen.
Since the interface bitmap contains also modes faster than 1000base-x,
this caused a regression wherein this module stopped working
out-of-the-box.
Fix this.
Fixes: fd580c9830316eda ("net: sfp: augment SFP parsing with phy_interface_t bitmap")
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/20260129082227.17443-1-kabel@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
