| Age | Commit message (Collapse) | Author |
|---|
|
Some PCI devices have PCI_MSI_FLAGS_64BIT in the MSI capability, but
implement less than 64 address bits. This breaks on platforms where such
a device is assigned an MSI address higher than what's supported.
Currently, no_64bit_msi bit is set for these devices, meaning that only
32-bit MSI addresses are allowed for them. However, on some platforms the
MSI doorbell address is above the 32-bit limit but within the addressable
range of the device.
As a first step to enable MSI on those combinations of devices and
platforms, convert the boolean no_64bit_msi flag to a DMA mask and fixup
the affected usage sites:
- no_64bit_msi = 1 -> msi_addr_mask = DMA_BIT_MASK(32)
- no_64bit_msi = 0 -> msi_addr_mask = DMA_BIT_MASK(64)
- if (no_64bit_msi) -> if (msi_addr_mask < DMA_BIT_MASK(64))
Since no values other than DMA_BIT_MASK(32) and DMA_BIT_MASK(64) are used,
this is functionally equivalent.
This prepares for changing the binary decision between 32 and 64 bit to a
DMA mask based decision which allows to support systems which have a DMA
address space less than 64bit but a MSI doorbell address above the 32-bit
limit.
[ tglx: Massaged changelog ]
Signed-off-by: Vivian Wang <wangruikang@iscas.ac.cn>
Signed-off-by: Thomas Gleixner <tglx@kernel.org>
Reviewed-by: Brett Creeley <brett.creeley@amd.com> # ionic
Reviewed-by: Thomas Gleixner <tglx@kernel.org>
Acked-by: Takashi Iwai <tiwai@suse.de> # sound
Link: https://patch.msgid.link/20260129-pci-msi-addr-mask-v4-1-70da998f2750@iscas.ac.cn
|
|
The i40e driver calls udp_tunnel_get_rx_info() during i40e_open().
This is redundant because UDP tunnel RX offload state is preserved
across device down/up cycles. The udp_tunnel core handles
synchronization automatically when required.
Furthermore, recent changes in the udp_tunnel infrastructure require
querying RX info while holding the udp_tunnel lock. Calling it
directly from the ndo_open path violates this requirement,
triggering the following lockdep warning:
Call Trace:
<TASK>
? __udp_tunnel_nic_assert_locked+0x39/0x40 [udp_tunnel]
i40e_open+0x135/0x14f [i40e]
__dev_open+0x121/0x2e0
__dev_change_flags+0x227/0x270
dev_change_flags+0x3d/0xb0
devinet_ioctl+0x56f/0x860
sock_do_ioctl+0x7b/0x130
__x64_sys_ioctl+0x91/0xd0
do_syscall_64+0x90/0x170
...
</TASK>
Remove the redundant and unsafe call to udp_tunnel_get_rx_info() from
i40e_open() resolve the locking violation.
Fixes: 1ead7501094c ("udp_tunnel: remove rtnl_lock dependency")
Signed-off-by: Mohammad Heib <mheib@redhat.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The ice driver calls udp_tunnel_get_rx_info() during ice_open_internal().
This is redundant because UDP tunnel RX offload state is preserved
across device down/up cycles. The udp_tunnel core handles
synchronization automatically when required.
Furthermore, recent changes in the udp_tunnel infrastructure require
querying RX info while holding the udp_tunnel lock. Calling it
directly from the ndo_open path violates this requirement,
triggering the following lockdep warning:
Call Trace:
<TASK>
ice_open_internal+0x253/0x350 [ice]
__udp_tunnel_nic_assert_locked+0x86/0xb0 [udp_tunnel]
__dev_open+0x2f5/0x880
__dev_change_flags+0x44c/0x660
netif_change_flags+0x80/0x160
devinet_ioctl+0xd21/0x15f0
inet_ioctl+0x311/0x350
sock_ioctl+0x114/0x220
__x64_sys_ioctl+0x131/0x1a0
...
</TASK>
Remove the redundant and unsafe call to udp_tunnel_get_rx_info() from
ice_open_internal() to resolve the locking violation
Fixes: 1ead7501094c ("udp_tunnel: remove rtnl_lock dependency")
Signed-off-by: Mohammad Heib <mheib@redhat.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Fix race condition where PTP periodic work runs while VSI is being
rebuilt, accessing NULL vsi->rx_rings.
The sequence was:
1. ice_ptp_prepare_for_reset() cancels PTP work
2. ice_ptp_rebuild() immediately queues PTP work
3. VSI rebuild happens AFTER ice_ptp_rebuild()
4. PTP work runs and accesses NULL vsi->rx_rings
Fix: Keep PTP work cancelled during rebuild, only queue it after
VSI rebuild completes in ice_rebuild().
Added ice_ptp_queue_work() helper function to encapsulate the logic
for queuing PTP work, ensuring it's only queued when PTP is supported
and the state is ICE_PTP_READY.
Error log:
[ 121.392544] ice 0000:60:00.1: PTP reset successful
[ 121.392692] BUG: kernel NULL pointer dereference, address: 0000000000000000
[ 121.392712] #PF: supervisor read access in kernel mode
[ 121.392720] #PF: error_code(0x0000) - not-present page
[ 121.392727] PGD 0
[ 121.392734] Oops: Oops: 0000 [#1] SMP NOPTI
[ 121.392746] CPU: 8 UID: 0 PID: 1005 Comm: ice-ptp-0000:60 Tainted: G S 6.19.0-rc6+ #4 PREEMPT(voluntary)
[ 121.392761] Tainted: [S]=CPU_OUT_OF_SPEC
[ 121.392773] RIP: 0010:ice_ptp_update_cached_phctime+0xbf/0x150 [ice]
[ 121.393042] Call Trace:
[ 121.393047] <TASK>
[ 121.393055] ice_ptp_periodic_work+0x69/0x180 [ice]
[ 121.393202] kthread_worker_fn+0xa2/0x260
[ 121.393216] ? __pfx_ice_ptp_periodic_work+0x10/0x10 [ice]
[ 121.393359] ? __pfx_kthread_worker_fn+0x10/0x10
[ 121.393371] kthread+0x10d/0x230
[ 121.393382] ? __pfx_kthread+0x10/0x10
[ 121.393393] ret_from_fork+0x273/0x2b0
[ 121.393407] ? __pfx_kthread+0x10/0x10
[ 121.393417] ret_from_fork_asm+0x1a/0x30
[ 121.393432] </TASK>
Fixes: 803bef817807d ("ice: factor out ice_ptp_rebuild_owner()")
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The E825 hardware currently has each PF handle the PFINT_TSYN_TX cause of
the miscellaneous OICR interrupt vector. The actual interrupt cause
underlying this is shared by all ports on the same quad:
┌─────────────────────────────────┐
│ │
│ ┌────┐ ┌────┐ ┌────┐ ┌────┐ │
│ │PF 0│ │PF 1│ │PF 2│ │PF 3│ │
│ └────┘ └────┘ └────┘ └────┘ │
│ │
└────────────────▲────────────────┘
│
│
┌────────────────┼────────────────┐
│ PHY QUAD │
└───▲────────▲────────▲────────▲──┘
│ │ │ │
┌───┼──┐ ┌───┴──┐ ┌───┼──┐ ┌───┼──┐
│Port 0│ │Port 1│ │Port 2│ │Port 3│
└──────┘ └──────┘ └──────┘ └──────┘
If multiple PFs issue Tx timestamp requests near simultaneously, it is
possible that the correct PF will not be interrupted and will miss its
timestamp. Understanding why is somewhat complex.
Consider the following sequence of events:
CPU 0:
Send Tx packet on PF 0
...
PF 0 enqueues packet with Tx request CPU 1, PF1:
... Send Tx packet on PF1
... PF 1 enqueues packet with Tx request
HW:
PHY Port 0 sends packet
PHY raises Tx timestamp event interrupt
MAC raises each PF interrupt
CPU 0, PF0: CPU 1, PF1:
ice_misc_intr() checks for Tx timestamps ice_misc_intr() checks for Tx timestamp
Sees packet ready bit set Sees nothing available
... Exits
...
...
HW:
PHY port 1 sends packet
PHY interrupt ignored because not all packet timestamps read yet.
...
Read timestamp, report to stack
Because the interrupt event is shared for all ports on the same quad, the
PHY will not raise a new interrupt for any PF until all timestamps are
read.
In the example above, the second timestamp comes in for port 1 before the
timestamp from port 0 is read. At this point, there is no longer an
interrupt thread running that will read the timestamps, because each PF has
checked and found that there was no work to do. Applications such as ptp4l
will timeout after waiting a few milliseconds. Eventually, the watchdog
service task will re-check for all quads and notice that there are
outstanding timestamps, and issue a software interrupt to recover. However,
by this point it is far too late, and applications have already failed.
All of this occurs because of the underlying hardware behavior. The PHY
cannot raise a new interrupt signal until all outstanding timestamps have
been read.
As a first step to fix this, switch the E825C hardware to the
ICE_PTP_TX_INTERRUPT_ALL mode. In this mode, only the clock owner PF will
respond to the PFINT_TSYN_TX cause. Other PFs disable this cause and will
not wake. In this mode, the clock owner will iterate over all ports and
handle timestamps for each connected port.
This matches the E822 behavior, and is a necessary but insufficient step to
resolve the missing timestamps.
Even with use of the ICE_PTP_TX_INTERRUPT_ALL mode, we still sometimes miss
a timestamp event. The ice_ptp_tx_tstamp_owner() does re-check the ready
bitmap, but does so before re-enabling the OICR interrupt vector. It also
only checks the ready bitmap, but not the software Tx timestamp tracker.
To avoid risk of losing a timestamp, refactor the logic to check both the
software Tx timestamp tracker bitmap *and* the hardware ready bitmap.
Additionally, do this outside of ice_ptp_process_ts() after we have already
re-enabled the OICR interrupt.
Remove the checks from the ice_ptp_tx_tstamp(), ice_ptp_tx_tstamp_owner(),
and the ice_ptp_process_ts() functions. This results in ice_ptp_tx_tstamp()
being nothing more than a wrapper around ice_ptp_process_tx_tstamp() so we
can remove it.
Add the ice_ptp_tx_tstamps_pending() function which returns a boolean
indicating if there are any pending Tx timestamps. First, check the
software timestamp tracker bitmap. In ICE_PTP_TX_INTERRUPT_ALL mode, check
*all* ports software trackers. If a tracker has outstanding timestamp
requests, return true. Additionally, check the PHY ready bitmap to confirm
if the PHY indicates any outstanding timestamps.
In the ice_misc_thread_fn(), call ice_ptp_tx_tstamps_pending() just before
returning from the IRQ thread handler. If it returns true, write to
PFINT_OICR to trigger a PFINT_OICR_TSYN_TX_M software interrupt. This will
force the handler to interrupt again and complete the work even if the PHY
hardware did not interrupt for any reason.
This results in the following new flow for handling Tx timestamps:
1) send Tx packet
2) PHY captures timestamp
3) PHY triggers MAC interrupt
4) clock owner executes ice_misc_intr() with PFINT_OICR_TSYN_TX flag set
5) ice_ptp_ts_irq() returns IRQ_WAKE_THREAD
7) The interrupt thread wakes up and kernel calls ice_misc_intr_thread_fn()
8) ice_ptp_process_ts() is called to handle any outstanding timestamps
9) ice_irq_dynamic_ena() is called to re-enable the OICR hardware interrupt
cause
10) ice_ptp_tx_tstamps_pending() is called to check if we missed any more
outstanding timestamps, checking both software and hardware indicators.
With this change, it should no longer be possible for new timestamps to
come in such a way that we lose an interrupt. If a timestamp comes in
before the ice_ptp_tx_tstamps_pending() call, it will be noticed by at
least one of the software bitmap check or the hardware bitmap check. If the
timestamp comes in *after* this check, it should cause a timestamp
interrupt as we have already read all timestamps from the PHY and the OICR
vector has been re-enabled.
Fixes: 7cab44f1c35f ("ice: Introduce ETH56G PHY model for E825C products")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Przemyslaw Korba <przemyslaw.korba@intel.com>
Tested-by: Vitaly Grinberg <vgrinber@redhat.com>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Modify PTP (Precision Time Protocol) configuration on link down flow.
Previously, PHY_REG_TX_OFFSET_READY register was cleared in such case.
This register is used to determine if the timestamp is valid or not on
the hardware side.
However, there is a possibility that there is still the packet in the
HW queue which originally was supposed to be timestamped but the link
is already down and given register is cleared.
This potentially might lead to the situation in which that 'delayed'
packet's timestamp is treated as invalid one when the link is up
again.
This in turn leads to the situation in which the driver is not able to
effectively clean timestamp memory and interrupt configuration.
From the hardware perspective, that 'old' interrupt was not handled
properly and even if new timestamp packets are processed, no new
interrupts is generated. As a result, providing timestamps to the user
applications (like ptp4l) is not possible.
The solution for this problem is implemented at the driver level rather
than the firmware, and maintains the tx_ready bit high, even during
link down events. This avoids entering a potential inconsistent state
between the driver and the timestamp hardware.
Testing hints:
- run PTP traffic at higher rate (like 16 PTP messages per second)
- observe ptp4l behaviour at the client side in the following
conditions:
a) trigger link toggle events. It needs to be physiscal
link down/up events
b) link speed change
In all above cases, PTP processing at ptp4l application should resume
always. In failure case, the following permanent error message in ptp4l
log was observed:
controller-0 ptp4l: err [6175.116] ptp4l-legacy timed out while polling
for tx timestamp
Fixes: 7cab44f1c35f ("ice: Introduce ETH56G PHY model for E825C products")
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
When an arvif is initialized in non-AP STA mode but MLO connection
preparation fails before the arvif is created
(arvif->is_created remains false), the error path attempts to delete all
links. However, link deletion only executes when arvif->is_created is true.
As a result, ahvif retains a stale entry of arvif that is initialized but
not created.
When a new arvif is initialized with the same link id, this stale mapping
triggers the following WARN_ON.
WARNING: drivers/net/wireless/ath/ath12k/mac.c:4271 at ath12k_mac_op_change_vif_links+0x140/0x180 [ath12k], CPU#3: wpa_supplicant/275
Call trace:
ath12k_mac_op_change_vif_links+0x140/0x180 [ath12k] (P)
drv_change_vif_links+0xbc/0x1a4 [mac80211]
ieee80211_vif_update_links+0x54c/0x6a0 [mac80211]
ieee80211_vif_set_links+0x40/0x70 [mac80211]
ieee80211_prep_connection+0x84/0x450 [mac80211]
ieee80211_mgd_auth+0x200/0x480 [mac80211]
ieee80211_auth+0x14/0x20 [mac80211]
cfg80211_mlme_auth+0x90/0xf0 [cfg80211]
nl80211_authenticate+0x32c/0x380 [cfg80211]
genl_family_rcv_msg_doit+0xc8/0x134
Fix this issue by unassigning the link vif and clearing ahvif->links_map
if arvif is only initialized but not created.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.5-01651-QCAHKSWPL_SILICONZ-1
Fixes: 81e4be30544e ("wifi: ath12k: handle link removal in change_vif_links()")
Signed-off-by: Aaradhana Sahu <aaradhana.sahu@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Link: https://patch.msgid.link/20260127033400.1721220-1-aaradhana.sahu@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Add support to request and receive TX hardware queue stats using
HTT stats type 3. This stats type reports MPDU mac id and hardware
queue information, including xretry, BAR, RTS, CTS, self, and QoS-null
counts, along with underrun, flush, and filter counters.
Sample output:
-------------
echo 3 >/sys/kernel/debug/ath12k/pci-0000\:58\:00.0/mac0/htt_stats_type
cat /sys/kernel/debug/ath12k/pci-0000\:58\:00.0/mac0/htt_stats
HTT_TX_HWQ_STATS_CMN_TLV:
mac_id = 0
hwq_id = 0
xretry = 0
underrun_cnt = 0
flush_cnt = 0
filt_cnt = 0
null_mpdu_bmap = 0
user_ack_failure = 379
ack_tlv_proc = 0
sched_id_proc = 0
null_mpdu_tx_count = 0
mpdu_bmap_not_recvd = 0
num_bar = 0
rts = 0
cts2self = 0
qos_null = 0
mpdu_tried_cnt = 379
mpdu_queued_cnt = 379
mpdu_ack_fail_cnt = 0
mpdu_filt_cnt = 0
false_mpdu_ack_count = 0
txq_timeout = 0
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.5-01651-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00302-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.115823.3
Signed-off-by: Aaradhana Sahu <aaradhana.sahu@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Link: https://patch.msgid.link/20260123071253.2202644-4-aaradhana.sahu@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Add support to request and receive RX pdev firmware stats using HTT
stats type 2. This stats type reports PPDU and MPDU counters, firmware
ring and buffer statistics, and RX suspend and resume counts.
Note: Currently, firmware on mobile-centric chipsets do not maintain
these statistics, so a query will not return any information.
Sample output:
-------------
echo 2 >/sys/kernel/debug/ath12k/pci-0000\:58\:00.0/mac0/htt_stats_type
cat /sys/kernel/debug/ath12k/pci-0000\:58\:00.0/mac0/htt_stats
HTT_RX_PDEV_FW_STATS_TLV:
mac_id = 0
ppdu_recvd = 1522
mpdu_cnt_fcs_ok = 1522
mpdu_cnt_fcs_err = 0
...
fw_ring_mpdu_ind = 1522
fw_ring_mgmt_subtype = 0:0, 1:0, 2:0, 3:0, 4:21, 5:0, 6:0, 7:0, 8:1501, 9:0, 10:0, 11:0, 12:0, 13:0, 14:0, 15:0
fw_ring_ctrl_subtype = 0:0, 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0, 8:0, 9:0, 10:0, 11:0, 12:0, 13:0, 14:0, 15:0
fw_ring_mcast_data_msdu = 0
fw_pkt_buf_ring_refill_cnt = 1567
fw_pkt_buf_ring_empty_cnt = 1
...
rx_suspend_cnt = 4
rx_suspend_fail_cnt = 0
rx_resume_cnt = 4
rx_resume_fail_cnt = 0
rx_ring_switch_cnt = 0
rx_ring_restore_cnt = 0
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.5-01651-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aaradhana Sahu <aaradhana.sahu@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Link: https://patch.msgid.link/20260123071253.2202644-3-aaradhana.sahu@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Currently, print_array_to_buf_index() decrements index unconditionally.
This may lead to invalid buffer access when array_len is zero.
Fix this by decrementing index only when array_len is non-zero.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.5-01651-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00302-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.115823.3
Fixes: adf6df963c03 ("wifi: ath12k: Add support to parse requested stats_type")
Signed-off-by: Aaradhana Sahu <aaradhana.sahu@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Link: https://patch.msgid.link/20260123071253.2202644-2-aaradhana.sahu@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Configure HE OBSS PD for spatial reuse in ath12k based on mac80211
HE SPR parameters in AP mode. This adds a pdev-level helper that
programs SRG/non-SRG OBSS PD thresholds, per-AC enablement, SR prohibit
control, and SRG/non-SRG BSS color and partial BSSID bitmaps via WMI.
Replace the previous vdev-level OBSS SPR command usage with the new
pdev-level configuration path, allowing firmware to apply HE spatial
reuse behavior according to the HE SPR/OBSS PD settings provided by
mac80211.
Tested-on: WCN7850 hw2.0 PCI WLAN.IOE_HMT.1.1-00011-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Tested-on: QCN9274 hw2.0 WLAN.WBE.1.5-01651-QCAHKSWPL_SILICONZ-1
Signed-off-by: Wei Zhang <wei.zhang@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Link: https://patch.msgid.link/20260123064817.364047-3-wei.zhang@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Add WMI support for configuring SRG and non-SRG OBSS PD bitmaps at
the pdev level. The new commands allow the host to set BSS color bitmaps,
partial BSSID bitmaps, and the corresponding enable masks used for
SRG/non-SRG OBSS PD processing.
Introduce new WMI command IDs, TLV tags, a service flag
(WMI_TLV_SERVICE_SRG_SRP_SPATIAL_REUSE_SUPPORT), and a bitmap payload
structure required by these commands. These additions are needed to
support HE Spatial Reuse and firmware-managed OBSS PD behavior.
The APIs introduced in this patch will be utilized in an upcoming patch.
Tested-on: WCN7850 hw2.0 PCI WLAN.IOE_HMT.1.1-00011-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Tested-on: QCN9274 hw2.0 WLAN.WBE.1.5-01651-QCAHKSWPL_SILICONZ-1
Signed-off-by: Wei Zhang <wei.zhang@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Link: https://patch.msgid.link/20260123064817.364047-2-wei.zhang@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
For M.2 WLAN chips, there is no suitable DTS node to specify the
firmware-name property. In addition, assigning firmware for the
M.2 PCIe interface causes chips that do not use usecase specific
firmware to fail. Therefore, abandoning the approach of specifying
firmware in DTS. As an alternative, propose a static lookup table
mapping device compatible to firmware names. Currently, only WCN6855
HW2.1 requires this.
However, support for the firmware-name property is retained to keep
the ABI backwards compatible.
For details on usecase specific firmware, see:
https://lore.kernel.org/all/20250522013444.1301330-3-miaoqing.pan@oss.qualcomm.com/.
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-04685-QCAHSPSWPL_V1_V2_SILICONZ_IOE-1
Fixes: edbbc647c4f3 ("wifi: ath11k: support usercase-specific firmware overrides")
Signed-off-by: Miaoqing Pan <miaoqing.pan@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Link: https://patch.msgid.link/20260121095055.3683957-2-miaoqing.pan@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
ath10k_sdio_fw_crashed_dump() calls ath10k_coredump_new() which requires
ar->dump_mutex to be held, as indicated by lockdep_assert_held() in that
function. However, the SDIO implementation does not acquire this lock,
unlike the PCI and SNOC implementations which properly hold the mutex.
Additionally, ar->stats.fw_crash_counter is documented as protected by
ar->data_lock in core.h, but the SDIO implementation modifies it without
holding this spinlock.
Add the missing mutex_lock()/mutex_unlock() around the coredump
operations, and add spin_lock_bh()/spin_unlock_bh() around the
fw_crash_counter increment, following the pattern used in
ath10k_pci_fw_dump_work() and ath10k_snoc_fw_crashed_dump().
Fixes: 3c45f21af84e ("ath10k: sdio: add firmware coredump support")
Signed-off-by: Ziyi Guo <n7l8m4@u.northwestern.edu>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Link: https://patch.msgid.link/20260123045822.2221549-1-n7l8m4@u.northwestern.edu
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
ath10k_wmi_event_peer_sta_ps_state_chg() uses lockdep_assert_held() to
assert that ar->data_lock should be held by the caller, but neither
ath10k_wmi_10_2_op_rx() nor ath10k_wmi_10_4_op_rx() acquire this lock
before calling this function.
The field arsta->peer_ps_state is documented as protected by
ar->data_lock in core.h, and other accessors (ath10k_peer_ps_state_disable,
ath10k_dbg_sta_read_peer_ps_state) properly acquire this lock.
Add spin_lock_bh()/spin_unlock_bh() around the peer_ps_state update,
and remove the lockdep_assert_held() to be aligned with new locking,
following the pattern used by other WMI event handlers in the driver.
Signed-off-by: Ziyi Guo <n7l8m4@u.northwestern.edu>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Link: https://patch.msgid.link/20260123175611.767731-1-n7l8m4@u.northwestern.edu
[removed excess blank line]
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
The WCN39xx family of WiFi/BT chips incorporates a simple PMU, spreading
voltages over internal rails. Implement support for using powersequencer
for this family of ATH10k devices in addition to using regulators.
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://patch.msgid.link/20260119-wcn3990-pwrctl-v3-3-948df19f5ec2@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
SPS OCP (over current protection) is a mechanism to cut off power to
protect hardware. When this happens, raise an interrupt to signal driver,
which prints out a message to note hardware status.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20260127085036.44060-7-pkshih@realtek.com
|
|
The LDO (Low Dropout Regulator) setting is missing after suspend/resume
in some platforms, and it will cause card loss. Therefore, reconfigure
this setting to avoid it.
Signed-off-by: Dian-Syuan Yang <dian_syuan0116@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20260127085036.44060-6-pkshih@realtek.com
|
|
The WiFi 7 chips use different registers to configure MU group for
beamforming. Define specific registers and refactor the common flow.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20260127085036.44060-5-pkshih@realtek.com
|
|
Except for the 8852A, 8852B, 8851B, 8852BT, all subsequent chips use
HAXIDMA. Therefore, interrupts need to be disabled before swapping
firmware to avoid unexpected SER.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20260127085036.44060-4-pkshih@realtek.com
|
|
SER (system error recovery) L0/L1 simulation has two kinds of methods.
How to choose them depends on FW features. But, Wi-Fi 7 misused them.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20260127085036.44060-3-pkshih@realtek.com
|
|
Sync Realtek terms on SER (system error recovery) simulation.
No logic is changed.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20260127085036.44060-2-pkshih@realtek.com
|
|
Enable TPA functionality in the VNIC and add functions
to handle TPA events, which help in processing LRO/GRO.
Signed-off-by: Bhargava Marreddy <bhargava.marreddy@broadcom.com>
Reviewed-by: Vikas Gupta <vikas.gupta@broadcom.com>
Reviewed-by: Rajashekar Hudumula <rajashekar.hudumula@broadcom.com>
Link: https://patch.msgid.link/20260128185623.26559-9-bhargava.marreddy@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add the functions to handle TPA events in RX path.
This helps the next patch enable TPA functionality.
Signed-off-by: Bhargava Marreddy <bhargava.marreddy@broadcom.com>
Reviewed-by: Vikas Gupta <vikas.gupta@broadcom.com>
Reviewed-by: Rajashekar Hudumula <rajashekar.hudumula@broadcom.com>
Link: https://patch.msgid.link/20260128185623.26559-8-bhargava.marreddy@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add AGG event handling in the RX path to receive packet data
on AGG rings. This enables Jumbo and HDS functionality.
Signed-off-by: Bhargava Marreddy <bhargava.marreddy@broadcom.com>
Reviewed-by: Vikas Gupta <vikas.gupta@broadcom.com>
Reviewed-by: Rajashekar Hudumula <rajashekar.hudumula@broadcom.com>
Link: https://patch.msgid.link/20260128185623.26559-7-bhargava.marreddy@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Implement ndo_features_check to validate hardware constraints per-packet:
- Disable SG if nr_frags exceeds hardware limit.
- Disable GSO if packet/fragment length exceeds supported maximum.
Signed-off-by: Bhargava Marreddy <bhargava.marreddy@broadcom.com>
Reviewed-by: Vikas Gupta <vikas.gupta@broadcom.com>
Reviewed-by: Ajit Kumar Khaparde <ajit.khaparde@broadcom.com>
Reviewed-by: Rahul Gupta <rahul-rg.gupta@broadcom.com>
Link: https://patch.msgid.link/20260128185623.26559-6-bhargava.marreddy@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add functions to support xmit along with TSO/GSO.
Also, add functions to handle TX completion events in the NAPI context.
This commit introduces the fundamental transmit data path
Signed-off-by: Bhargava Marreddy <bhargava.marreddy@broadcom.com>
Reviewed-by: Vikas Gupta <vikas.gupta@broadcom.com>
Reviewed-by: Rajashekar Hudumula <rajashekar.hudumula@broadcom.com>
Reviewed-by: Ajit Kumar Khaparde <ajit.khaparde@broadcom.com>
Reviewed-by: Rahul Gupta <rahul-rg.gupta@broadcom.com>
Link: https://patch.msgid.link/20260128185623.26559-5-bhargava.marreddy@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Since the HWRM completion for a sent request lands on the NQ,
add functions to handle the HWRM completion event.
Signed-off-by: Bhargava Marreddy <bhargava.marreddy@broadcom.com>
Reviewed-by: Vikas Gupta <vikas.gupta@broadcom.com>
Reviewed-by: Rajashekar Hudumula <rajashekar.hudumula@broadcom.com>
Link: https://patch.msgid.link/20260128185623.26559-4-bhargava.marreddy@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support to receive packet using NAPI, build and deliver the skb
to stack. With help of meta data available in completions, fill the
appropriate information in skb.
Signed-off-by: Bhargava Marreddy <bhargava.marreddy@broadcom.com>
Reviewed-by: Vikas Gupta <vikas.gupta@broadcom.com>
Reviewed-by: Rajashekar Hudumula <rajashekar.hudumula@broadcom.com>
Reviewed-by: Ajit Kumar Khaparde <ajit.khaparde@broadcom.com>
Reviewed-by: Rahul Gupta <rahul-rg.gupta@broadcom.com>
Link: https://patch.msgid.link/20260128185623.26559-3-bhargava.marreddy@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add rx-copybreak support in bnge_set_ring_params()
Signed-off-by: Bhargava Marreddy <bhargava.marreddy@broadcom.com>
Reviewed-by: Vikas Gupta <vikas.gupta@broadcom.com>
Reviewed-by: Rajashekar Hudumula <rajashekar.hudumula@broadcom.com>
Link: https://patch.msgid.link/20260128185623.26559-2-bhargava.marreddy@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The IRQ handler extracts if_id from the upper 16 bits of the hardware
status register and uses it to index into ethsw->ports[] without
validation. Since if_id can be any 16-bit value (0-65535) but the ports
array is only allocated with sw_attr.num_ifs elements, this can lead to
an out-of-bounds read potentially.
Add a bounds check before accessing the array, consistent with the
existing validation in dpaa2_switch_rx().
Reported-by: Yuhao Jiang <danisjiang@gmail.com>
Reported-by: Junrui Luo <moonafterrain@outlook.com>
Fixes: 24ab724f8a46 ("dpaa2-switch: use the port index in the IRQ handler")
Signed-off-by: Junrui Luo <moonafterrain@outlook.com>
Link: https://patch.msgid.link/SYBPR01MB7881D420AB43FF1A227B84AFAF91A@SYBPR01MB7881.ausprd01.prod.outlook.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Similar to Lantech 8330-262D-E, the Lantech 8330-265D also reports
2500MBd instead of 3125MBd.
Also, all 8330-265D report normal RX_LOS in EEPROM, but some signal
inverted RX_LOS. We therefore need to ignore RX_LOS on these modules.
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://patch.msgid.link/20260128170044.15576-1-kabel@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This patch updates the count_eot calculation for CN20K devices.
Where the count_eot feild extended to 2 bits, while maintaining
CN10K compatibility where only bit 0 is used.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260128022448.4402-1-gakula@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In setup_nic_devices(), the initialization loop jumps to the label
setup_nic_dev_free on failure. The current cleanup loop while(i--)
skip the failing index i, causing a memory leak.
Fix this by changing the loop to iterate from the current index i
down to 0.
Compile tested only. Issue found using code review.
Fixes: 846b46873eeb ("liquidio CN23XX: VF offload features")
Suggested-by: Simon Horman <horms@kernel.org>
Signed-off-by: Zilin Guan <zilin@seu.edu.cn>
Reviewed-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://patch.msgid.link/20260128154440.278369-4-zilin@seu.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In setup_nic_devices(), the initialization loop jumps to the label
setup_nic_dev_free on failure. The current cleanup loop while(i--)
skip the failing index i, causing a memory leak.
Fix this by changing the loop to iterate from the current index i
down to 0.
Also, decrement i in the devlink_alloc failure path to point to the
last successfully allocated index.
Compile tested only. Issue found using code review.
Fixes: f21fb3ed364b ("Add support of Cavium Liquidio ethernet adapters")
Suggested-by: Simon Horman <horms@kernel.org>
Signed-off-by: Zilin Guan <zilin@seu.edu.cn>
Reviewed-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://patch.msgid.link/20260128154440.278369-3-zilin@seu.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In setup_nic_devices(), the netdev is allocated using alloc_etherdev_mq().
However, the pointer to this structure is stored in oct->props[i].netdev
only after the calls to netif_set_real_num_rx_queues() and
netif_set_real_num_tx_queues().
If either of these functions fails, setup_nic_devices() returns an error
without freeing the allocated netdev. Since oct->props[i].netdev is still
NULL at this point, the cleanup function liquidio_destroy_nic_device()
will fail to find and free the netdev, resulting in a memory leak.
Fix this by initializing oct->props[i].netdev before calling the queue
setup functions. This ensures that the netdev is properly accessible for
cleanup in case of errors.
Compile tested only. Issue found using a prototype static analysis tool
and code review.
Fixes: c33c997346c3 ("liquidio: enhanced ethtool --set-channels feature")
Signed-off-by: Zilin Guan <zilin@seu.edu.cn>
Reviewed-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://patch.msgid.link/20260128154440.278369-2-zilin@seu.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Johannes Berg says:
====================
Another fairly large set of changes, notably:
- cfg80211/mac80211
- most of EPPKE/802.1X over auth frames support
- additional FTM capabilities
- split up drop reasons better, removing generic RX_DROP
- NAN cleanups/fixes
- ath11k:
- support for Channel Frequency Response measurement
- ath12k:
- support for the QCC2072 chipset
- iwlwifi:
- partial NAN support
- UNII-9 support
- some UHR/802.11bn FW APIs
- remove most of MLO/EHT from iwlmvm
(such devices use iwlmld)
- rtw89:
- preparations for RTL8922DE support
* tag 'wireless-next-2026-01-29' of https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (184 commits)
wifi: iwlegacy: add missing mutex protection in il4965_store_tx_power()
wifi: iwlegacy: add missing mutex protection in il3945_store_measurement()
wifi: mac80211: use u64_stats_t with u64_stats_sync properly
wifi: p54: Fix memory leak in p54_beacon_update()
wifi: cfg80211: treat deprecated INDOOR_SP_AP_OLD control value as LPI mode
wifi: rtw88: sdio: Migrate to use sdio specific shutdown function
wifi: rsi: sdio: Migrate to use sdio specific shutdown function
sdio: Provide a bustype shutdown function
wifi: nl80211/cfg80211: support operating as RSTA in PMSR FTM request
wifi: nl80211/cfg80211: add negotiated burst period to FTM result
wifi: nl80211/cfg80211: clarify periodic FTM parameters for non-EDCA based ranging
wifi: nl80211/cfg80211: add new FTM capabilities
wifi: iwlwifi: rename struct iwl_mcc_allowed_ap_type_cmd::offset_map
wifi: iwlwifi: mvm: Remove link_id from time_events
wifi: iwlwifi: mld: change cluster_id type to u8 array
wifi: iwlwifi: support V13 of iwl_lari_config_change_cmd
wifi: iwlwifi: split bios_value_u32 to separate the header
wifi: iwlwifi: uefi: cache the DSM functions
wifi: iwlwifi: acpi: cache the DSM functions
wifi: iwlwifi: mvm: Cleanup MLO code
...
====================
Link: https://patch.msgid.link/20260129110136.176980-39-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Implement clk provider driver so we can disable the clock output when it
isn't needed. This helps to reduce EMF noise
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Link: https://patch.msgid.link/20260127125547.1475164-4-bjorn@mork.no
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The Airoha AN8811HB is mostly compatible with the EN8811H, adding 10Base-T
support and reducing power consumption.
This driver is based on the air_an8811hb v0.0.4 out-of-tree driver
written by "Lucien.Jheng <lucien.jheng@airoha.com>"
Firmware is available in linux-firmware. The driver has been tested with
firmware version 25110702
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Link: https://patch.msgid.link/20260127125547.1475164-3-bjorn@mork.no
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Create reusable helpers in preparation for the AN8811HB support.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Link: https://patch.msgid.link/20260127125547.1475164-2-bjorn@mork.no
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The driver now depends on the core to tell it what the rx page size
should be for the agg ring. We must populate the ndo_default_qcfg
callback even if we don't support any queue ops.
This fixes:
Oops: divide error: 0000 [#1] SMP DEBUG_PAGEALLOC KASAN
RIP: 0010:bnxt_alloc_rx_page_pool (drivers/net/ethernet/broadcom/bnxt/bnxt.c:3852)
with fw version 225.1.109.0.
Link: https://lore.kernel.org/20250421222827.283737-20-kuba@kernel.org
Fixes: f96e1b35779e ("eth: bnxt: support qcfg provided rx page size")
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20260128193258.125274-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Separate the CTX_PREF_CI_HI of rq and sq to improve readability.
Co-developed-by: Zhu Yikai <zhuyikai1@h-partners.com>
Signed-off-by: Zhu Yikai <zhuyikai1@h-partners.com>
Signed-off-by: Fan Gong <gongfan1@huawei.com>
Link: https://patch.msgid.link/7b34bf318c64398f34048c823c15b2eec5a679bc.1769656467.git.zhuyikai1@h-partners.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Since commit 17fcb3dc12bb ("hinic3: module initialization and tx/rx logic")
use "size * sizeof(u64)" in hinic3_feature_nego.
Use array_size instead of multiplying can make it clearer.
Link: https://lore.kernel.org/netdev/20250911123120.GG30363@horms.kernel.org/
Co-developed-by: Zhu Yikai <zhuyikai1@h-partners.com>
Signed-off-by: Zhu Yikai <zhuyikai1@h-partners.com>
Signed-off-by: Fan Gong <gongfan1@huawei.com>
Reviewed-by: Joe Damato <joe@dama.to>
Link: https://patch.msgid.link/b7d6d384ccc0bd4c0d3e7af1f90901d589cbd0b1.1769656467.git.zhuyikai1@h-partners.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Since commit 1f3838b84a63 ("hinic3: Add Rss function") nic_dev->num_txqs
cannot be zero in hinic3_alloc_txqs(). So remove the check for this case.
Link: https://lore.kernel.org/netdev/20250902180843.5ba05bf2@kernel.org/
Co-developed-by: Zhu Yikai <zhuyikai1@h-partners.com>
Signed-off-by: Zhu Yikai <zhuyikai1@h-partners.com>
Signed-off-by: Fan Gong <gongfan1@huawei.com>
Link: https://patch.msgid.link/c23daa9b79fa731c1caaec9b8245f6b2c4994afb.1769656467.git.zhuyikai1@h-partners.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
According to previous review comment, fix code style of removing empty
lines between the actions on the error handling path to make it more
idiomatic in the merged code.
Link: https://lore.kernel.org/netdev/20250902180937.4c8d9eb3@kernel.org/
Co-developed-by: Zhu Yikai <zhuyikai1@h-partners.com>
Signed-off-by: Zhu Yikai <zhuyikai1@h-partners.com>
Signed-off-by: Fan Gong <gongfan1@huawei.com>
Link: https://patch.msgid.link/ccff2ae7abe91bb3618ded9bb5ef2dc9cb243d22.1769656467.git.zhuyikai1@h-partners.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
NIX SQ manager sticky mode is known to cause stalls when multiple SQs
share an SMQ and transmit concurrently. Additionally, PSE may deadlock
on transitions between sticky and non-sticky transmissions. There is
also a credit drop issue observed when certain condition clocks are
gated.
work around these hardware errata by:
- Disabling SQM sticky operation:
- Clear TM6 (bit 15)
- Clear TM11 (bit 14)
- Disabling sticky → non-sticky transition path that can deadlock PSE:
- Clear TM5 (bit 23)
- Preventing credit drops by keeping the control-flow clock enabled:
- Set TM9 (bit 21)
These changes are applied via NIX_AF_SQM_DBG_CTL_STATUS. With this
configuration the SQM/PSE maintain forward progress under load without
credit loss, at the cost of disabling sticky optimizations.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260127125147.1642-1-gakula@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The driver allocates arrays for ports, FDBs, and filter blocks using
kcalloc() with ethsw->sw_attr.num_ifs as the element count. When the
device reports zero interfaces (either due to hardware configuration
or firmware issues), kcalloc(0, ...) returns ZERO_SIZE_PTR (0x10)
instead of NULL.
Later in dpaa2_switch_probe(), the NAPI initialization unconditionally
accesses ethsw->ports[0]->netdev, which attempts to dereference
ZERO_SIZE_PTR (address 0x10), resulting in a kernel panic.
Add a check to ensure num_ifs is greater than zero after retrieving
device attributes. This prevents the zero-sized allocations and
subsequent invalid pointer dereference.
Reported-by: Yuhao Jiang <danisjiang@gmail.com>
Reported-by: Junrui Luo <moonafterrain@outlook.com>
Fixes: 0b1b71370458 ("staging: dpaa2-switch: handle Rx path on control interface")
Signed-off-by: Junrui Luo <moonafterrain@outlook.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/SYBPR01MB7881BEABA8DA896947962470AF91A@SYBPR01MB7881.ausprd01.prod.outlook.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add a SoC specific init method.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1vl3G5-00000006v3X-2zfD@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
All the definitions of the RGMII related xxx_GMAC_CLK_xxx definitions
use the same field values to select the clock rate. Provide common
definitions for these field values, passing them in to a single macro
for each variant that generates the appropriate values for the speed
register.
No change to produced code on aarch64.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/E1vl3G0-00000006v3R-2ZBc@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
rk_gmac_setup() delves into the PHY's DT node to retrieve its reset
control using of_reset_control_get(). However, it never releases it
when the driver is removed. Add reset_control_put() to rk_gmac_exit()
to clean this up.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://patch.msgid.link/E1vl3Fv-00000006v3L-215v@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
