| Age | Commit message (Collapse) | Author |
|---|
|
The maximum number of descriptors supported by the hardware is
hardware-dependent and can be retrieved using
i40e_get_max_num_descriptors(). Move this function to a shared header
and use it when checking for valid ring_len parameter rather than using
hardcoded value.
By fixing an over-acceptance issue, behavior change could be seen where
ring_len could now be rejected while configuring rx and tx queues if its
size is larger than the hardware-dependent maximum number of
descriptors.
Fixes: 55d225670def ("i40e: add validation for ring_len param")
Signed-off-by: Gregory Herrero <gregory.herrero@oracle.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Add service task schedule to set_rx_mode.
In some cases there are error messages printed out in PTP application
(ptp4l):
ptp4l[13848.762]: port 1 (ens2f3np3): received SYNC without timestamp
ptp4l[13848.825]: port 1 (ens2f3np3): received SYNC without timestamp
ptp4l[13848.887]: port 1 (ens2f3np3): received SYNC without timestamp
This happens when service task would not run immediately after
set_rx_mode, and we need it for setup tasks. This service task checks, if
PTP RX packets are hung in firmware, and propagate correct settings such
as multicast address for IEEE 1588 Precision Time Protocol.
RX timestamping depends on some of these filters set. Bug happens only
with high PTP packets frequency incoming, and not every run since
sometimes service task is being ran from a different place immediately
after starting ptp4l.
Fixes: 0e4425ed641f ("i40e: fix: do not sleep in netdev_ops")
Reviewed-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Przemyslaw Korba <przemyslaw.korba@intel.com>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Since commit dfb073d32cac ("ptp: Return -EINVAL on ptp_clock_register if
required ops are NULL"), PTP clock registered through ptp_clock_register
is required to have ptp_clock_info.settime64 set, however, neither MVM
nor MLD's PTP clock implementation sets it, resulting in warnings when
the interface starts up, like
WARNING: drivers/ptp/ptp_clock.c:325 at ptp_clock_register+0x2c8/0x6b8, CPU#1: wpa_supplicant/469
CPU: 1 UID: 0 PID: 469 Comm: wpa_supplicant Not tainted 6.18.0+ #101 PREEMPT(full)
ra: ffff800002732cd4 iwl_mvm_ptp_init+0x114/0x188 [iwlmvm]
ERA: 9000000002fdc468 ptp_clock_register+0x2c8/0x6b8
iwlwifi 0000:01:00.0: Failed to register PHC clock (-22)
I don't find an appropriate firmware interface to implement settime64()
for iwlwifi MLD/MVM, thus instead create a stub that returns
-EOPTNOTSUPP only, suppressing the warning and allowing the PTP clock to
be registered.
Reported-by: Nathan Chancellor <nathan@kernel.org>
Closes: https://lore.kernel.org/all/20251108044822.GA3262936@ax162/
Signed-off-by: Yao Zi <ziyao@disroot.org>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
tested-by: damian Tometzki damian@riscv-rocks.de
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20251204123204.9316-1-ziyao@disroot.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
On my system the arithmetic done on the firmware numbers
results in a negative number, but since the types are
unsigned it gets interpreted as a large positive number.
The end result is that the firmware gets rejected and wifi
is defunct.
Switch to signed types to handle this case correctly.
iwlwifi 0000:0c:00.0: Driver unable to support your firmware API. Driver supports FW core 4294967294..2, firmware is 2.
iwlwifi 0000:0c:00.0: Direct firmware load for iwlwifi-5000-4.ucode failed with error -2
iwlwifi 0000:0c:00.0: Direct firmware load for iwlwifi-5000-3.ucode failed with error -2
iwlwifi 0000:0c:00.0: Direct firmware load for iwlwifi-5000-2.ucode failed with error -2
iwlwifi 0000:0c:00.0: Direct firmware load for iwlwifi-5000-1.ucode failed with error -2
iwlwifi 0000:0c:00.0: no suitable firmware found!
iwlwifi 0000:0c:00.0: minimum version required: iwlwifi-5000-1
iwlwifi 0000:0c:00.0: maximum version supported: iwlwifi-5000-5
iwlwifi 0000:0c:00.0: check git://git.kernel.org/pub/scm/linux/kernel/git/firmware/linux-firmware.git
Cc: stable@vger.kernel.org
Fixes: 5f708cccde9d ("wifi: iwlwifi: add a new FW file numbering scheme")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=220805
Link: https://patch.msgid.link/20251113222852.15896-1-ville.syrjala@linux.intel.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This avoids occasional skb_under_panic Oops from wl1271_tx_work. In this case, headroom is
less than needed (typically 110 - 94 = 16 bytes).
Signed-off-by: Peter Astrand <astrand@lysator.liu.se>
Link: https://patch.msgid.link/097bd417-e1d7-acd4-be05-47b199075013@lysator.liu.se
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
As originally proposed in [1], the ath12k driver was re-architected in
the ath12k-ng branch to separate the logic specific to 802.11be (Wi-Fi
7) from the core logic. This separation will allow ath12k to also
support 802.11bn (Wi-Fi 8) in the future. Now merge this into ath-next.
Many thanks to everyone who worked on this re-architecture. Special
thanks to Vasanthakumar Thiagarajan and Baochen Qiang who reviewed
every patch, and to Ripan Deuri for the ath12k-ng => ath-next merge
conflict resolution.
Link: https://lore.kernel.org/all/4a17d730-ede8-463e-98d8-9b0291d0ca45@oss.qualcomm.com/ # [1]
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
This reverts commit 9c194fe4625db18f93d5abcfb7f7997557a0b29d.
This commit breaks all USB wifi adapters supported by rtw88:
usb 1-2: new high-speed USB device number 6 using xhci_hcd
usb 1-2: New USB device found, idVendor=2357, idProduct=0138, bcdDevice= 2.10
usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-2: Product: 802.11ac NIC
usb 1-2: Manufacturer: Realtek
usb 1-2: SerialNumber: 123456
------------[ cut here ]------------
WARNING: CPU: 3 PID: 152 at kernel/workqueue.c:5667 alloc_workqueue_noprof+0x676/0x770
[...]
Call Trace:
<TASK>
? rtw_usb_probe+0x30e/0xa5c [rtw88_usb 4af3cb64eedafeecbfb08f80c1e9e2893e2ee7a6]
rtw_usb_probe+0x3eb/0xa5c [rtw88_usb 4af3cb64eedafeecbfb08f80c1e9e2893e2ee7a6]
usb_probe_interface+0xdd/0x2c0
really_probe+0xdb/0x340
? pm_runtime_barrier+0x55/0x90
? __pfx___device_attach_driver+0x10/0x10
__driver_probe_device+0x78/0x140
driver_probe_device+0x1f/0xa0
__device_attach_driver+0x89/0x110
bus_for_each_drv+0x8f/0xe0
__device_attach+0xb0/0x1c0
bus_probe_device+0x90/0xa0
device_add+0x663/0x880
usb_set_configuration+0x5a5/0x870
usb_generic_driver_probe+0x4a/0x70
usb_probe_device+0x3d/0x140
? driver_sysfs_add+0x59/0xd0
really_probe+0xdb/0x340
? pm_runtime_barrier+0x55/0x90
? __pfx___device_attach_driver+0x10/0x10
__driver_probe_device+0x78/0x140
driver_probe_device+0x1f/0xa0
__device_attach_driver+0x89/0x110
bus_for_each_drv+0x8f/0xe0
__device_attach+0xb0/0x1c0
bus_probe_device+0x90/0xa0
device_add+0x663/0x880
usb_new_device.cold+0x141/0x3b5
hub_event+0x1132/0x1900
? page_counter_uncharge+0x4a/0x90
process_one_work+0x190/0x350
worker_thread+0x2d7/0x410
? __pfx_worker_thread+0x10/0x10
kthread+0xf9/0x240
? __pfx_kthread+0x10/0x10
? __pfx_kthread+0x10/0x10
ret_from_fork+0x1c1/0x1f0
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1a/0x30
</TASK>
---[ end trace 0000000000000000 ]---
rtw88_8822bu 1-2:1.0: failed to create RX work queue
rtw88_8822bu 1-2:1.0: failed to init USB RX
rtw88_8822bu 1-2:1.0: Firmware version 27.2.0, H2C version 13
rtw88_8822bu 1-2:1.0: probe with driver rtw88_8822bu failed with error -12
WQ_UNBOUND is not compatible with WQ_BH. Comment in enum wq_flags in
workqueue.h says:
/* BH wq only allows the following flags */
__WQ_BH_ALLOWS = WQ_BH | WQ_HIGHPRI | WQ_PERCPU,
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/d57efe48-b8ff-4bf1-942c-7e808535eda6@gmail.com
|
|
TID getting from ieee80211_get_tid() might be out of range of array size
of sta_entry->tids[], so check TID is less than MAX_TID_COUNT. Othwerwise,
UBSAN warn:
UBSAN: array-index-out-of-bounds in drivers/net/wireless/realtek/rtlwifi/rtl8192cu/trx.c:514:30
index 10 is out of range for type 'rtl_tid_data [9]'
Fixes: 8ca4cdef9329 ("wifi: rtlwifi: rtl8192cu: Fix TX aggregation")
Signed-off-by: Morning Star <alexbestoso@gmail.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/1764232628-13625-1-git-send-email-pkshih@realtek.com
|
|
The indirect IO is necessary for RTL8822CS, but not necessary for other
chips. Otherwiese, it throws errors and becomes unusable.
rtw88_8723cs mmc1:0001:1: WOW Firmware version 11.0.0, H2C version 0
rtw88_8723cs mmc1:0001:1: Firmware version 11.0.0, H2C version 0
rtw88_8723cs mmc1:0001:1: sdio read32 failed (0xf0): -110
rtw88_8723cs mmc1:0001:1: sdio write8 failed (0x1c): -110
rtw88_8723cs mmc1:0001:1: sdio read32 failed (0xf0): -110
By vendor driver, only RTL8822CS and RTL8822ES need indirect IO, but
RTL8822ES isn't supported yet. Therefore, limit it to RTL8822CS only.
Reported-by: Andrey Skvortsov <andrej.skvortzov@gmail.com>
Closes: https://lore.kernel.org/linux-wireless/07a32e2d6c764eb1bd9415b5a921a652@realtek.com/T/#m997b4522f7209ba629561c776bfd1d13ab24c1d4
Fixes: 58de1f91e033 ("wifi: rtw88: sdio: use indirect IO for device registers before power-on")
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Tested-by: Andrey Skvortsov <andrej.skvortzov@gmail.com>
Link: https://patch.msgid.link/1764034729-1251-1-git-send-email-pkshih@realtek.com
|
|
Some Potron SFP+ XGSPON ONU sticks are shipped with different EEPROM
vendor ID and vendor name strings, but are otherwise functionally
identical to the existing "Potron SFP+ XGSPON ONU Stick" handled by
sfp_quirk_potron().
These modules, including units distributed under the "Better Internet"
branding, use the same UART pin assignment and require the same
TX_FAULT/LOS behaviour and boot delay. Re-use the existing Potron
quirk for this EEPROM variant.
Signed-off-by: Marcus Hughes <marcus.hughes@betterinternet.ltd>
Link: https://patch.msgid.link/20251207210355.333451-1-marcus.hughes@betterinternet.ltd
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2025-12-10
Arnd Bergmann's patch fixes a build dependency with the CAN protocols
and drivers introduced in the current development cycle.
The last patch is by me and fixes the error handling cleanup in the
gs_usb driver.
* tag 'linux-can-fixes-for-6.19-20251210' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
can: gs_usb: gs_can_open(): fix error handling
can: fix build dependency
====================
Link: https://patch.msgid.link/20251210083448.2116869-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
On execution path with raised B44_FLAG_EXTERNAL_PHY, b44_readphy()
leaves bmcr value uninitialized and it is used later in the code.
Add check of this flag at the beginning of the b44_nway_reset() and
exit early of the function with restarting autonegotiation if an
external PHY is used.
Fixes: 753f492093da ("[B44]: port to native ssb support")
Reviewed-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexey Simakov <bigalex934@gmail.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20251205155815.4348-1-bigalex934@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The new icssg-prueth driver needs the same dependency as the other parts
that use the ptp-1588:
WARNING: unmet direct dependencies detected for TI_ICSS_IEP
Depends on [m]: NETDEVICES [=y] && ETHERNET [=y] && NET_VENDOR_TI [=y] && PTP_1588_CLOCK_OPTIONAL [=m] && TI_PRUSS [=y]
Selected by [y]:
- TI_PRUETH [=y] && NETDEVICES [=y] && ETHERNET [=y] && NET_VENDOR_TI [=y] && PRU_REMOTEPROC [=y] && NET_SWITCHDEV [=y]
Add the correct dependency on the two drivers missing it, and remove
the pointless 'imply' in the process.
Fixes: e654b85a693e ("net: ti: icssg-prueth: Add ICSSG Ethernet driver for AM65x SR1.0 platforms")
Fixes: 511f6c1ae093 ("net: ti: icssm-prueth: Adds ICSSM Ethernet driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20251204100138.1034175-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit 2603be9e8167 ("can: gs_usb: gs_can_open(): improve error handling")
added missing error handling to the gs_can_open() function.
The driver uses 2 USB anchors to track the allocated URBs: the TX URBs in
struct gs_can::tx_submitted for each netdev and the RX URBs in struct
gs_usb::rx_submitted for the USB device. gs_can_open() allocates the RX
URBs, while TX URBs are allocated during gs_can_start_xmit().
The cleanup in gs_can_open() kills all anchored dev->tx_submitted
URBs (which is not necessary since the netdev is not yet registered), but
misses the parent->rx_submitted URBs.
Fix the problem by killing the rx_submitted instead of the tx_submitted.
Fixes: 2603be9e8167 ("can: gs_usb: gs_can_open(): improve error handling")
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20251210-gs_usb-fix-error-handling-v1-1-d6a5a03f10bb@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
A recent bugfix introduced a new problem with Kconfig dependencies:
WARNING: unmet direct dependencies detected for CAN_DEV
Depends on [n]: NETDEVICES [=n] && CAN [=m]
Selected by [m]:
- CAN [=m] && NET [=y]
Since the CAN core code now links into the CAN device code, that
particular function needs to be available, though the rest of it
does not.
Revert the incomplete fix and instead use Makefile logic to avoid
the link failure.
Fixes: cb2dc6d2869a ("can: Kconfig: select CAN driver infrastructure by default")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202512091523.zty3CLmc-lkp@intel.com/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://patch.msgid.link/20251204100015.1033688-1-arnd@kernel.org
[mkl: removed module option from CAN_DEV help text (thanks Vincent)]
[mkl: removed '&& CAN' from Kconfig dependency (thanks Vincent)]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Consider a multi-link AP configuration:
MLD vif (MAC addr: aa:bb)
|-- 2.4 GHz link (BSSID: aa:bb)
|-- 5 GHz link (BSSID: cc:dd)
For AP vdevs, ath12k creates a DP peer using the arvif's BSSID and stores
it in dp_hw->dp_peers_list. During scan operations, the driver assigns an
arvif to the scan vdev and uses the vif's MAC address as its BSSID. In
the above scenario, the scan vdev MAC address (aa:bb) matches the BSSID
of the 2.4 GHz AP link, causing a duplicate entry in dp_hw->dp_peers_list
and leading to scan vdev creation failure.
Failure in vif bringup sequence:
1. Create AP vdev for 2.4 GHz link:
- Assign arvif with BSSID = aa:bb and link_id = 0.
- Create DP peer with address aa:bb and add to dp_hw->dp_peers_list.
2. Create scan vdev for 5 GHz link:
- Assign arvif with BSSID = aa:bb (same as vif MAC address) and
link_id = 15.
- Attempt to create another DP peer with address aa:bb.
- Operation fails because aa:bb already exists in dp_hw->dp_peers_list,
resulting in duplicate entry conflict.
3. Delete scan vdev for 5 GHz link.
4. Create AP vdev for 5 GHz link.
Since DP peer is not needed for scan operations, identify scan vdev using
arvif->link_id >= IEEE80211_MLD_MAX_NUM_LINKS and skip DP peer creation
and deletion.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.5-01651-QCAHKSWPL_SILICONZ-1
Signed-off-by: Ripan Deuri <quic_rdeuri@quicinc.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20251207072717.95542-1-quic_rdeuri@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux
Pull i3c updates from Alexandre Belloni:
"HDR support has finally been added. mipi-i3c-hci has been reworked and
Intel Nova Lake-S support has been added.
Subsystem:
- Add HDR transfer support
Drivers:
- dw: fix bus hang on Agilex5
- mipi-i3c-hci: Intel Nova Lake-S support, IOMMU support
- svc: HDR support"
* tag 'i3c/for-6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux: (28 commits)
regmap: i3c: switch to use i3c_xfer from i3c_priv_xfer
net: mctp i3c: switch to use i3c_xfer from i3c_priv_xfer
hwmon: (lm75): switch to use i3c_xfer from i3c_priv_xfer
i3c: document i3c_xfers
i3c: fix I3C_SDR bit number
i3c: master: svc: Add basic HDR mode support
i3c: master: svc: Replace bool rnw with union for HDR support
i3c: Switch to use new i3c_xfer from i3c_priv_xfer
i3c: Add HDR API support
i3c: master: add WQ_PERCPU to alloc_workqueue users
i3c: master: Remove i3c_device_free_ibi from i3c_device_remove
i3c: mipi-i3c-hci-pci: Set d3cold_delay to 0 for Intel controllers
i3c: mipi-i3c-hci-pci: Add LTR support for Intel controllers
i3c: mipi-i3c-hci-pci: Add exit callback
i3c: mipi-i3c-hci-pci: Change callback parameter
i3c: mipi-i3c-hci-pci: Allocate a structure for mipi_i3c_hci_pci device information
i3c: mipi-i3c-hci-pci: Factor out intel_reset()
i3c: mipi-i3c-hci-pci: Factor out private registers ioremapping
i3c: mipi-i3c-hci-pci: Constify driver data
i3c: mipi-i3c-hci-pci: Use readl_poll_timeout()
...
|
|
Pull rdma updates from Jason Gunthorpe:
"This has another new RDMA driver 'bng_en' for latest generation
Broadcom NICs. There might be one more new driver still to come.
Otherwise it is a fairly quite cycle. Summary:
- Minor driver bug fixes and updates to cxgb4, rxe, rdmavt, bnxt_re,
mlx5
- Many bug fix patches for irdma
- WQ_PERCPU annotations and system_dfl_wq changes
- Improved mlx5 support for "other eswitches" and multiple PFs
- 1600Gbps link speed reporting support. Four Digits Now!
- New driver bng_en for latest generation Broadcom NICs
- Bonding support for hns
- Adjust mlx5's hmm based ODP to work with the very large address
space created by the new 5 level paging default on x86
- Lockdep fixups in rxe and siw"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (65 commits)
RDMA/rxe: reclassify sockets in order to avoid false positives from lockdep
RDMA/siw: reclassify sockets in order to avoid false positives from lockdep
RDMA/bng_re: Remove prefetch instruction
RDMA/core: Reduce cond_resched() frequency in __ib_umem_release
RDMA/irdma: Fix SRQ shadow area address initialization
RDMA/irdma: Remove doorbell elision logic
RDMA/irdma: Do not set IBK_LOCAL_DMA_LKEY for GEN3+
RDMA/irdma: Do not directly rely on IB_PD_UNSAFE_GLOBAL_RKEY
RDMA/irdma: Add missing mutex destroy
RDMA/irdma: Fix SIGBUS in AEQ destroy
RDMA/irdma: Add a missing kfree of struct irdma_pci_f for GEN2
RDMA/irdma: Fix data race in irdma_free_pble
RDMA/irdma: Fix data race in irdma_sc_ccq_arm
RDMA/mlx5: Add support for 1600_8x lane speed
RDMA/core: Add new IB rate for XDR (8x) support
IB/mlx5: Reduce IMR KSM size when 5-level paging is enabled
RDMA/bnxt_re: Pass correct flag for dma mr creation
RDMA/bnxt_re: Fix the inline size for GenP7 devices
RDMA/hns: Support reset recovery for bond
RDMA/hns: Support link state reporting for bond
...
|
|
For XDP_TX action in bnxt_rx_xdp(), clearing of the event flags is not
correct. __bnxt_poll_work() -> bnxt_rx_pkt() -> bnxt_rx_xdp() may be
looping within NAPI and some event flags may be set in earlier
iterations. In particular, if BNXT_TX_EVENT is set earlier indicating
some XDP_TX packets are ready and pending, it will be cleared if it is
XDP_TX action again. Normally, we will set BNXT_TX_EVENT again when we
successfully call __bnxt_xmit_xdp(). But if the TX ring has no more
room, the flag will not be set. This will cause the TX producer to be
ahead but the driver will not hit the TX doorbell.
For multi-buf XDP_TX, there is no need to clear the event flags and set
BNXT_AGG_EVENT. The BNXT_AGG_EVENT flag should have been set earlier in
bnxt_rx_pkt().
The visible symptom of this is that the RX ring associated with the
TX XDP ring will eventually become empty and all packets will be dropped.
Because this condition will cause the driver to not refill the RX ring
seeing that the TX ring has forever pending XDP_TX packets.
The fix is to only clear BNXT_RX_EVENT when we have successfully
called __bnxt_xmit_xdp().
Fixes: 7f0a168b0441 ("bnxt_en: Add completion ring pointer in TX and RX ring structures")
Reported-by: Pavel Dubovitsky <pdubovitsky@meta.com>
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20251203003024.2246699-1-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
commit 46e7860ef941 ("gve: Move ptp_schedule_worker to gve_init_clock")
moved the first invocation of the AQ command REPORT_NIC_TIMESTAMP to
gve_probe(). However, gve_init_clock() invoking REPORT_NIC_TIMESTAMP is
not valid until after gve_probe() invokes the AQ command
CONFIGURE_DEVICE_RESOURCES.
Failure to do so results in the following error:
gve 0000:00:07.0: failed to read NIC clock -11
This was missed earlier because the driver under test was loaded at
runtime instead of boot-time. The boot-time driver had already
initialized the device, causing the runtime driver to successfully call
gve_init_clock() incorrectly.
Fixes: 46e7860ef941 ("gve: Move ptp_schedule_worker to gve_init_clock")
Reviewed-by: Ankit Garg <nktgrg@google.com>
Signed-off-by: Tim Hostetler <thostet@google.com>
Signed-off-by: Harshitha Ramamurthy <hramamurthy@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251202200207.1434749-1-hramamurthy@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Wake-on-Lan does currently not work for r8169 in DASH mode, e.g. the
ASUS Pro WS X570-ACE with RTL8168fp/RTL8117.
Fix by not returning early in rtl_prepare_power_down when dash_enabled.
While this fixes WoL, it still kills the OOB RTL8117 remote management
BMC connection. Fix by not calling rtl8168_driver_stop if WoL is enabled.
Fixes: 065c27c184d6 ("r8169: phy power ops")
Signed-off-by: René Rebe <rene@exactco.de>
Cc: stable@vger.kernel.org
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/20251202.194137.1647877804487085954.rene@exactco.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cited commit added a dedicated mutex (instead of RTNL) to protect the
multicast route list, so that it will not change while the driver
periodically traverses it in order to update the kernel about multicast
route stats that were queried from the device.
One instance of list entry deletion (during route replace) was missed
and it can result in a use-after-free [1].
Fix by acquiring the mutex before deleting the entry from the list and
releasing it afterwards.
[1]
BUG: KASAN: slab-use-after-free in mlxsw_sp_mr_stats_update+0x4a5/0x540 drivers/net/ethernet/mellanox/mlxsw/spectrum_mr.c:1006 [mlxsw_spectrum]
Read of size 8 at addr ffff8881523c2fa8 by task kworker/2:5/22043
CPU: 2 UID: 0 PID: 22043 Comm: kworker/2:5 Not tainted 6.18.0-rc1-custom-g1a3d6d7cd014 #1 PREEMPT(full)
Hardware name: Mellanox Technologies Ltd. MSN2010/SA002610, BIOS 5.6.5 08/24/2017
Workqueue: mlxsw_core mlxsw_sp_mr_stats_update [mlxsw_spectrum]
Call Trace:
<TASK>
dump_stack_lvl+0xba/0x110
print_report+0x174/0x4f5
kasan_report+0xdf/0x110
mlxsw_sp_mr_stats_update+0x4a5/0x540 drivers/net/ethernet/mellanox/mlxsw/spectrum_mr.c:1006 [mlxsw_spectrum]
process_one_work+0x9cc/0x18e0
worker_thread+0x5df/0xe40
kthread+0x3b8/0x730
ret_from_fork+0x3e9/0x560
ret_from_fork_asm+0x1a/0x30
</TASK>
Allocated by task 29933:
kasan_save_stack+0x30/0x50
kasan_save_track+0x14/0x30
__kasan_kmalloc+0x8f/0xa0
mlxsw_sp_mr_route_add+0xd8/0x4770 [mlxsw_spectrum]
mlxsw_sp_router_fibmr_event_work+0x371/0xad0 drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c:7965 [mlxsw_spectrum]
process_one_work+0x9cc/0x18e0
worker_thread+0x5df/0xe40
kthread+0x3b8/0x730
ret_from_fork+0x3e9/0x560
ret_from_fork_asm+0x1a/0x30
Freed by task 29933:
kasan_save_stack+0x30/0x50
kasan_save_track+0x14/0x30
__kasan_save_free_info+0x3b/0x70
__kasan_slab_free+0x43/0x70
kfree+0x14e/0x700
mlxsw_sp_mr_route_add+0x2dea/0x4770 drivers/net/ethernet/mellanox/mlxsw/spectrum_mr.c:444 [mlxsw_spectrum]
mlxsw_sp_router_fibmr_event_work+0x371/0xad0 drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c:7965 [mlxsw_spectrum]
process_one_work+0x9cc/0x18e0
worker_thread+0x5df/0xe40
kthread+0x3b8/0x730
ret_from_fork+0x3e9/0x560
ret_from_fork_asm+0x1a/0x30
Fixes: f38656d06725 ("mlxsw: spectrum_mr: Protect multicast route list with a lock")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/f996feecfd59fde297964bfc85040b6d83ec6089.1764695650.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We sometimes observe use-after-free when dereferencing a neighbour [1].
The problem seems to be that the driver stores a pointer to the
neighbour, but without holding a reference on it. A reference is only
taken when the neighbour is used by a nexthop.
Fix by simplifying the reference counting scheme. Always take a
reference when storing a neighbour pointer in a neighbour entry. Avoid
taking a referencing when the neighbour is used by a nexthop as the
neighbour entry associated with the nexthop already holds a reference.
Tested by running the test that uncovered the problem over 300 times.
Without this patch the problem was reproduced after a handful of
iterations.
[1]
BUG: KASAN: slab-use-after-free in mlxsw_sp_neigh_entry_update+0x2d4/0x310
Read of size 8 at addr ffff88817f8e3420 by task ip/3929
CPU: 3 UID: 0 PID: 3929 Comm: ip Not tainted 6.18.0-rc4-virtme-g36b21a067510 #3 PREEMPT(full)
Hardware name: Nvidia SN5600/VMOD0013, BIOS 5.13 05/31/2023
Call Trace:
<TASK>
dump_stack_lvl+0x6f/0xa0
print_address_description.constprop.0+0x6e/0x300
print_report+0xfc/0x1fb
kasan_report+0xe4/0x110
mlxsw_sp_neigh_entry_update+0x2d4/0x310
mlxsw_sp_router_rif_gone_sync+0x35f/0x510
mlxsw_sp_rif_destroy+0x1ea/0x730
mlxsw_sp_inetaddr_port_vlan_event+0xa1/0x1b0
__mlxsw_sp_inetaddr_lag_event+0xcc/0x130
__mlxsw_sp_inetaddr_event+0xf5/0x3c0
mlxsw_sp_router_netdevice_event+0x1015/0x1580
notifier_call_chain+0xcc/0x150
call_netdevice_notifiers_info+0x7e/0x100
__netdev_upper_dev_unlink+0x10b/0x210
netdev_upper_dev_unlink+0x79/0xa0
vrf_del_slave+0x18/0x50
do_set_master+0x146/0x7d0
do_setlink.isra.0+0x9a0/0x2880
rtnl_newlink+0x637/0xb20
rtnetlink_rcv_msg+0x6fe/0xb90
netlink_rcv_skb+0x123/0x380
netlink_unicast+0x4a3/0x770
netlink_sendmsg+0x75b/0xc90
__sock_sendmsg+0xbe/0x160
____sys_sendmsg+0x5b2/0x7d0
___sys_sendmsg+0xfd/0x180
__sys_sendmsg+0x124/0x1c0
do_syscall_64+0xbb/0xfd0
entry_SYSCALL_64_after_hwframe+0x4b/0x53
[...]
Allocated by task 109:
kasan_save_stack+0x30/0x50
kasan_save_track+0x14/0x30
__kasan_kmalloc+0x7b/0x90
__kmalloc_noprof+0x2c1/0x790
neigh_alloc+0x6af/0x8f0
___neigh_create+0x63/0xe90
mlxsw_sp_nexthop_neigh_init+0x430/0x7e0
mlxsw_sp_nexthop_type_init+0x212/0x960
mlxsw_sp_nexthop6_group_info_init.constprop.0+0x81f/0x1280
mlxsw_sp_nexthop6_group_get+0x392/0x6a0
mlxsw_sp_fib6_entry_create+0x46a/0xfd0
mlxsw_sp_router_fib6_replace+0x1ed/0x5f0
mlxsw_sp_router_fib6_event_work+0x10a/0x2a0
process_one_work+0xd57/0x1390
worker_thread+0x4d6/0xd40
kthread+0x355/0x5b0
ret_from_fork+0x1d4/0x270
ret_from_fork_asm+0x11/0x20
Freed by task 154:
kasan_save_stack+0x30/0x50
kasan_save_track+0x14/0x30
__kasan_save_free_info+0x3b/0x60
__kasan_slab_free+0x43/0x70
kmem_cache_free_bulk.part.0+0x1eb/0x5e0
kvfree_rcu_bulk+0x1f2/0x260
kfree_rcu_work+0x130/0x1b0
process_one_work+0xd57/0x1390
worker_thread+0x4d6/0xd40
kthread+0x355/0x5b0
ret_from_fork+0x1d4/0x270
ret_from_fork_asm+0x11/0x20
Last potentially related work creation:
kasan_save_stack+0x30/0x50
kasan_record_aux_stack+0x8c/0xa0
kvfree_call_rcu+0x93/0x5b0
mlxsw_sp_router_neigh_event_work+0x67d/0x860
process_one_work+0xd57/0x1390
worker_thread+0x4d6/0xd40
kthread+0x355/0x5b0
ret_from_fork+0x1d4/0x270
ret_from_fork_asm+0x11/0x20
Fixes: 6cf3c971dc84 ("mlxsw: spectrum_router: Add private neigh table")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/92d75e21d95d163a41b5cea67a15cd33f547cba6.1764695650.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
mlxsw_sp_router_schedule_work() takes a reference on a neighbour,
expecting a work item to release it later on. However, we might fail to
schedule the work item, in which case the neighbour reference count will
be leaked.
Fix by taking the reference just before scheduling the work item. Note
that mlxsw_sp_router_schedule_work() can receive a NULL neighbour
pointer, but neigh_clone() handles that correctly.
Spotted during code review, did not actually observe the reference count
leak.
Fixes: 151b89f6025a ("mlxsw: spectrum_router: Reuse work neighbor initialization in work scheduler")
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/ec2934ae4aca187a8d8c9329a08ce93cca411378.1764695650.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The local variable 'val' was never clamped to -75000 or 180000 because
the return value of clamp_val() was not used. Fix this by assigning the
clamped value back to 'val', and use clamp() instead of clamp_val().
Cc: stable@vger.kernel.org
Fixes: a557a92e6881 ("net: phy: marvell-88q2xxx: add support for temperature sensor")
Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev>
Reviewed-by: Dimitri Fedrau <dima.fedrau@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20251202172743.453055-3-thorsten.blum@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Enable host bridge emulation for PCI_DOMAINS_GENERIC platforms (Dan
Williams)
- Switch vmd from custom domain number allocator to the common
allocator to prevent a potential race with new non-VMD buses (Dan
Williams)
- Enable Precision Time Measurement (PTM) only if device advertises
support for a relevant role, to prevent invalid PTM Requests that
cause ACS violations that are reported as AER Uncorrectable
Non-Fatal errors (Mika Westerberg)
Resource management:
- Prevent resource tree corruption when BAR resize fails (Ilpo
Järvinen)
- Restore BARs to the original size if a BAR resize fails (Ilpo
Järvinen)
- Remove BAR release from BAR resize attempts by the xe, i915, and
amdgpu drivers so the PCI core can restore BARs if the resize fails
(Ilpo Järvinen)
- Move Resizable BAR code to rebar.c (Ilpo Järvinen)
- Add pci_rebar_size_supported() and use it in i915 and xe (Ilpo
Järvinen)
- Add pci_rebar_get_max_size() and use it in xe and amdgpu (Ilpo
Järvinen)
Power management and error handling:
- For drivers using PCI legacy suspend, save config state at suspend
so that state (not any earlier state from enumeration, probe, or
error recovery) will be restored when resuming (Lukas Wunner)
- For devices with no driver or a driver that lacks power management,
save config state at hibernate so that state (not any earlier state
from enumeration, probe, or error recovery) will be restored when
resuming (Lukas Wunner)
- Save device config space on device addition, before driver binding,
so error recovery works more reliably (Lukas Wunner)
- Drop pci_save_state() from several drivers that no longer need it
since the PCI core always does it and pci_restore_state() no longer
invalidates the saved state (Lukas Wunner)
- Document use of pci_save_state() by drivers to capture the state
they want restored during error recovery (Lukas Wunner)
Power control:
- Add a struct pci_ops.assert_perst() function pointer to
assert/deassert PCIe PERST# and implement it for the qcom driver
(Krishna Chaitanya Chundru)
- Add DT binding and pwrctrl driver for the Toshiba TC9563 PCIe
switch, which must be held in reset after poweron so the pwrctrl
driver can configure the switch via I2C before bringing up the
links (Krishna Chaitanya Chundru)
Endpoint framework:
- Convert the endpoint doorbell test to use a threaded IRQ to fix a
'sleeping while atomic' issue (Bhanu Seshu Kumar Valluri)
- Add endpoint VNTB MSI doorbell support to reduce latency between
host and endpoint (Frank Li)
New native PCIe controller drivers:
- Add CIX Sky1 host controller DT binding and driver (Hans Zhang)
- Add NXP S32G host controller DT binding and driver (Vincent
Guittot)
- Add Renesas RZ/G3S host controller DT binding and driver (Claudiu
Beznea)
- Add SpacemiT K1 host controller DT binding and driver (Alex Elder)
Amlogic Meson PCIe controller driver:
- Update DT binding to name DBI region 'dbi', not 'elbi', and update
driver to support both (Manivannan Sadhasivam)
Apple PCIe controller driver:
- Move struct pci_host_bridge allocation from pci_host_common_init()
to callers, which significantly simplifies pcie-apple (Marc
Zyngier)
Broadcom STB PCIe controller driver:
- Disable advertising ASPM L0s support correctly (Jim Quinlan)
- Add a panic/die handler to print diagnostic info in case PCIe
caused an unrecoverable abort (Jim Quinlan)
Cadence PCIe controller driver:
- Add module support for Cadence platform host and endpoint
controller driver (Manikandan K Pillai)
- Split headers into 'legacy' (LGA) and 'high perf' (HPA) to prepare
for new CIX Sky1 driver (Manikandan K Pillai)
MediaTek PCIe controller driver:
- Convert DT binding to YAML schema (Christian Marangi)
- Add Airoha AN7583 DT compatible and driver support (Christian
Marangi)
Qualcomm PCIe controller driver:
- Add Qualcomm Kaanapali to SM8550 DT binding (Qiang Yu)
- Add required 'power-domains' and 'resets' to qcom sa8775p, sc7280,
sc8280xp, sm8150, sm8250, sm8350, sm8450, sm8550, x1e80100 DT
schemas (Krzysztof Kozlowski)
- Look up OPP using both frequency and data rate (not just frequency)
so RPMh votes can account for both (Krishna Chaitanya Chundru)
Rockchip DesignWare PCIe controller driver:
- Add Rockchip RK3528 compatible strings in DT binding (Yao Zi)
STMicroelectronics STM32MP25 PCIe controller driver:
- Fix a race between link training and endpoint register
initialization (Christian Bruel)
- Align endpoint allocations to match the ATU requirements (Christian
Bruel)
Synopsys DesignWare PCIe controller driver:
- Clear L1 PM Substate Capability 'Supported' bits unless glue driver
says it's supported, which prevents users from enabling non-working
L1SS. Currently only qcom and tegra194 support L1SS (Bjorn Helgaas)
- Remove now-superfluous L1SS disable code from tegra194 (Bjorn
Helgaas)
- Configure L1SS support in dw-rockchip when DT says
'supports-clkreq' (Shawn Lin)
TI Keystone PCIe controller driver:
- Fail the probe instead of silently succeeding if ks_pcie_of_data
didn't specify Root Complex or Endpoint mode (Siddharth Vadapalli)
- Make keystone buildable as a loadable module, except on ARM32 where
hook_fault_code() is __init (Siddharth Vadapalli)"
* tag 'pci-v6.19-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (100 commits)
MAINTAINERS: Add Manivannan Sadhasivam as PCI/pwrctrl maintainer
MAINTAINERS: Add CIX Sky1 PCIe controller driver maintainer
PCI: sky1: Add PCIe host support for CIX Sky1
dt-bindings: PCI: Add CIX Sky1 PCIe Root Complex bindings
PCI: cadence: Add support for High Perf Architecture (HPA) controller
MAINTAINERS: Add NXP S32G PCIe controller driver maintainer
PCI: s32g: Add NXP S32G PCIe controller driver (RC)
PCI: dwc: Add register and bitfield definitions
dt-bindings: PCI: s32g: Add NXP S32G PCIe controller
PCI: Add Renesas RZ/G3S host controller driver
PCI: host-generic: Move bridge allocation outside of pci_host_common_init()
dt-bindings: PCI: Add Renesas RZ/G3S PCIe controller binding
PCI: Validate pci_rebar_size_supported() input
Documentation: PCI: Amend error recovery doc with pci_save_state() rules
treewide: Drop pci_save_state() after pci_restore_state()
PCI/ERR: Ensure error recoverability at all times
PCI/PM: Stop needlessly clearing state_saved on enumeration and thaw
PCI/PM: Reinstate clearing state_saved in legacy and !PM codepaths
PCI: dw-rockchip: Configure L1SS support
PCI: tegra194: Remove unnecessary L1SS disable code
...
|
|
Clear hca_devcom_comp in device's private data after unregistering it in
LAG teardown. Otherwise a slightly lagging second pass through
mlx5_unload_one() might try to unregister it again and trip over
use-after-free.
On s390 almost all PCI level recovery events trigger two passes through
mxl5_unload_one() - one through the poll_health() method and one through
mlx5_pci_err_detected() as callback from generic PCI error recovery.
While testing PCI error recovery paths with more kernel debug features
enabled, this issue reproducibly led to kernel panics with the following
call chain:
Unable to handle kernel pointer dereference in virtual kernel address space
Failing address: 6b6b6b6b6b6b6000 TEID: 6b6b6b6b6b6b6803 ESOP-2 FSI
Fault in home space mode while using kernel ASCE.
AS:00000000705c4007 R3:0000000000000024
Oops: 0038 ilc:3 [#1]SMP
CPU: 14 UID: 0 PID: 156 Comm: kmcheck Kdump: loaded Not tainted
6.18.0-20251130.rc7.git0.16131a59cab1.300.fc43.s390x+debug #1 PREEMPT
Krnl PSW : 0404e00180000000 0000020fc86aa1dc (__lock_acquire+0x5c/0x15f0)
R:0 T:1 IO:0 EX:0 Key:0 M:1 W:0 P:0 AS:3 CC:2 PM:0 RI:0 EA:3
Krnl GPRS: 0000000000000000 0000020f00000001 6b6b6b6b6b6b6c33 0000000000000000
0000000000000000 0000000000000000 0000000000000001 0000000000000000
0000000000000000 0000020fca28b820 0000000000000000 0000010a1ced8100
0000010a1ced8100 0000020fc9775068 0000018fce14f8b8 0000018fce14f7f8
Krnl Code: 0000020fc86aa1cc: e3b003400004 lg %r11,832
0000020fc86aa1d2: a7840211 brc 8,0000020fc86aa5f4
*0000020fc86aa1d6: c09000df0b25 larl %r9,0000020fca28b820
>0000020fc86aa1dc: d50790002000 clc 0(8,%r9),0(%r2)
0000020fc86aa1e2: a7840209 brc 8,0000020fc86aa5f4
0000020fc86aa1e6: c0e001100401 larl %r14,0000020fca8aa9e8
0000020fc86aa1ec: c01000e25a00 larl %r1,0000020fca2f55ec
0000020fc86aa1f2: a7eb00e8 aghi %r14,232
Call Trace:
__lock_acquire+0x5c/0x15f0
lock_acquire.part.0+0xf8/0x270
lock_acquire+0xb0/0x1b0
down_write+0x5a/0x250
mlx5_detach_device+0x42/0x110 [mlx5_core]
mlx5_unload_one_devl_locked+0x50/0xc0 [mlx5_core]
mlx5_unload_one+0x42/0x60 [mlx5_core]
mlx5_pci_err_detected+0x94/0x150 [mlx5_core]
zpci_event_attempt_error_recovery+0xcc/0x388
Fixes: 5a977b5833b7 ("net/mlx5: Lag, move devcom registration to LAG layer")
Signed-off-by: Gerd Bayer <gbayer@linux.ibm.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Acked-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20251202-fix_lag-v1-1-59e8177ffce0@linux.ibm.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Packets with pkt_type == PACKET_LOOPBACK are captured by
handle_frame() function, but they don't have L2 header.
We should not process them in handle_mode_l2().
This doesn't affect old L2 functionality, since handling
was anyway incorrect.
Handle them the same way as in br_handle_frame():
just pass the skb.
To observe invalid behaviour, just start "ping -b" on bcast address
of port-interface.
Fixes: 2ad7bf363841 ("ipvlan: Initial check-in of the IPVLAN driver.")
Signed-off-by: Dmitry Skorodumov <skorodumov.dmitry@huawei.com>
Link: https://patch.msgid.link/20251202103906.4087675-1-skorodumov.dmitry@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
According to MaxLinear engineer Benny Weng the RX lane of the SerDes
port of the GSW1xx switches is inverted in hardware, and the
SGMII_PHY_RX0_CFG2_INVERT bit is set by default in order to compensate
for that. Hence also set the SGMII_PHY_RX0_CFG2_INVERT bit by default in
gsw1xx_pcs_reset().
Fixes: 22335939ec90 ("net: dsa: add driver for MaxLinear GSW1xx switch family")
Reported-by: Rasmus Villemoes <ravi@prevas.dk>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/ca10e9f780c0152ecf9ae8cbac5bf975802e8f99.1764668951.git.daniel@makrotopia.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When support for RTL8211F(D)(I)-VD-CG was introduced in commit
bb726b753f75 ("net: phy: realtek: add support for RTL8211F(D)(I)-VD-CG")
the implementation assumed that this PHY model doesn't have the
control register PHYCR2 (Page 0xa43 Address 0x19). This
assumption was based on the differences in CLKOUT configurations
between RTL8211FVD and the remaining RTL8211F PHYs. In the latter
commit 2c67301584f2
("net: phy: realtek: Avoid PHYCR2 access if PHYCR2 not present")
this assumption was expanded to the PHY-mode EEE.
I performed tests on RTL8211FI-VD-CG and confirmed that disabling
PHY-mode EEE works correctly and is uniform with other PHYs
supported by the driver. To validate the correctness,
I contacted Realtek support. Realtek confirmed that PHY-mode EEE on
RTL8211F(D)(I)-VD-CG is configured via Page 0xa43 Address 0x19 bit 5.
Moreover, Realtek informed me that the most recent datasheet
for RTL8211F(D)(I)-VD-CG v1.1 is incomplete and the naming of
control registers is partly inconsistent. The errata I
received from Realtek corrects the naming as follows:
| Register | Datasheet v1.1 | Errata |
|-------------------------|----------------|--------|
| Page 0xa44 Address 0x11 | PHYCR2 | PHYCR3 |
| Page 0xa43 Address 0x19 | N/A | PHYCR2 |
This information confirms that the supposedly missing control register,
PHYCR2, exists in the RTL8211F(D)(I)-VD-CG under the same address and
the same name. It controls widely the same configs as other PHYs from
the RTL8211F series (e.g. PHY-mode EEE). Clock out configuration is an
exception.
Given all this information, restore disabling of the PHY-mode EEE.
Fixes: 2c67301584f2 ("net: phy: realtek: Avoid PHYCR2 access if PHYCR2 not present")
Signed-off-by: Ivan Galkin <ivan.galkin@axis.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20251202-phy_eee-v1-1-fe0bf6ab3df0@axis.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
PSP is unregistered twice in:
_mlx5e_remove -> mlx5e_psp_unregister
mlx5e_nic_cleanup -> mlx5e_psp_unregister
This leads to a refcount underflow in some conditions:
------------[ cut here ]------------
refcount_t: underflow; use-after-free.
WARNING: CPU: 2 PID: 1694 at lib/refcount.c:28 refcount_warn_saturate+0xd8/0xe0
[...]
mlx5e_psp_unregister+0x26/0x50 [mlx5_core]
mlx5e_nic_cleanup+0x26/0x90 [mlx5_core]
mlx5e_remove+0xe6/0x1f0 [mlx5_core]
auxiliary_bus_remove+0x18/0x30
device_release_driver_internal+0x194/0x1f0
bus_remove_device+0xc6/0x130
device_del+0x159/0x3c0
mlx5_rescan_drivers_locked+0xbc/0x2a0 [mlx5_core]
[...]
Do not directly remove psp from the _mlx5e_remove path, the PSP cleanup
happens as part of profile cleanup.
Fixes: 89ee2d92f66c ("net/mlx5e: Support PSP offload functionality")
Signed-off-by: Cosmin Ratiu <cratiu@nvidia.com>
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/1764602008-1334866-3-git-send-email-tariqt@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The enable_mpesw() function returns -EINVAL if ldev->mode is not
MLX5_LAG_MODE_NONE. This means attempting to enable MPESW mode when it's
already enabled will fail. In contrast, disable_mpesw() properly checks
if the mode is MLX5_LAG_MODE_MPESW before proceeding, making it
naturally idempotent and safe to call multiple times.
Fix enable_mpesw() to return success if mpesw is already enabled.
Fixes: a32327a3a02c ("net/mlx5: Lag, Control MultiPort E-Switch single FDB mode")
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Shay Drori <shayd@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/1764602008-1334866-2-git-send-email-tariqt@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The ERR007885 will lead to a TDAR race condition for mutliQ when the
driver sets TDAR and the UDMA clears TDAR simultaneously or in a small
window (2-4 cycles). And it will cause the udma_tx and udma_tx_arbiter
state machines to hang. Therefore, the commit 53bb20d1faba ("net: fec:
add variable reg_desc_active to speed things up") and the commit
a179aad12bad ("net: fec: ERR007885 Workaround for conventional TX") have
added the workaround to fix the potential issue for the conventional TX
path. Similarly, the XDP TX path should also have the potential hang
issue, so add the workaround for XDP TX path.
Fixes: 6d6b39f180b8 ("net: fec: add initial XDP support")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Link: https://patch.msgid.link/20251128025915.2486943-1-wei.fang@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core & protocols:
- Replace busylock at the Tx queuing layer with a lockless list.
Resulting in a 300% (4x) improvement on heavy TX workloads, sending
twice the number of packets per second, for half the cpu cycles.
- Allow constantly busy flows to migrate to a more suitable CPU/NIC
queue.
Normally we perform queue re-selection when flow comes out of idle,
but under extreme circumstances the flows may be constantly busy.
Add sysctl to allow periodic rehashing even if it'd risk packet
reordering.
- Optimize the NAPI skb cache, make it larger, use it in more paths.
- Attempt returning Tx skbs to the originating CPU (like we already
did for Rx skbs).
- Various data structure layout and prefetch optimizations from Eric.
- Remove ktime_get() from the recvmsg() fast path, ktime_get() is
sadly quite expensive on recent AMD machines.
- Extend threaded NAPI polling to allow the kthread busy poll for
packets.
- Make MPTCP use Rx backlog processing. This lowers the lock
pressure, improving the Rx performance.
- Support memcg accounting of MPTCP socket memory.
- Allow admin to opt sockets out of global protocol memory accounting
(using a sysctl or BPF-based policy). The global limits are a poor
fit for modern container workloads, where limits are imposed using
cgroups.
- Improve heuristics for when to kick off AF_UNIX garbage collection.
- Allow users to control TCP SACK compression, and default to 33% of
RTT.
- Add tcp_rcvbuf_low_rtt sysctl to let datacenter users avoid
unnecessarily aggressive rcvbuf growth and overshot when the
connection RTT is low.
- Preserve skb metadata space across skb_push / skb_pull operations.
- Support for IPIP encapsulation in the nftables flowtable offload.
- Support appending IP interface information to ICMP messages (RFC
5837).
- Support setting max record size in TLS (RFC 8449).
- Remove taking rtnl_lock from RTM_GETNEIGHTBL and RTM_SETNEIGHTBL.
- Use a dedicated lock (and RCU) in MPLS, instead of rtnl_lock.
- Let users configure the number of write buffers in SMC.
- Add new struct sockaddr_unsized for sockaddr of unknown length,
from Kees.
- Some conversions away from the crypto_ahash API, from Eric Biggers.
- Some preparations for slimming down struct page.
- YAML Netlink protocol spec for WireGuard.
- Add a tool on top of YAML Netlink specs/lib for reporting commonly
computed derived statistics and summarized system state.
Driver API:
- Add CAN XL support to the CAN Netlink interface.
- Add uAPI for reporting PHY Mean Square Error (MSE) diagnostics, as
defined by the OPEN Alliance's "Advanced diagnostic features for
100BASE-T1 automotive Ethernet PHYs" specification.
- Add DPLL phase-adjust-gran pin attribute (and implement it in
zl3073x).
- Refactor xfrm_input lock to reduce contention when NIC offloads
IPsec and performs RSS.
- Add info to devlink params whether the current setting is the
default or a user override. Allow resetting back to default.
- Add standard device stats for PSP crypto offload.
- Leverage DSA frame broadcast to implement simple HSR frame
duplication for a lot of switches without dedicated HSR offload.
- Add uAPI defines for 1.6Tbps link modes.
Device drivers:
- Add Motorcomm YT921x gigabit Ethernet switch support.
- Add MUCSE driver for N500/N210 1GbE NIC series.
- Convert drivers to support dedicated ops for timestamping control,
and away from the direct IOCTL handling. While at it support GET
operations for PHY timestamping.
- Add (and convert most drivers to) a dedicated ethtool callback for
reading the Rx ring count.
- Significant refactoring efforts in the STMMAC driver, which
supports Synopsys turn-key MAC IP integrated into a ton of SoCs.
- Ethernet high-speed NICs:
- Broadcom (bnxt):
- support PPS in/out on all pins
- Intel (100G, ice, idpf):
- ice: implement standard ethtool and timestamping stats
- i40e: support setting the max number of MAC addresses per VF
- iavf: support RSS of GTP tunnels for 5G and LTE deployments
- nVidia/Mellanox (mlx5):
- reduce downtime on interface reconfiguration
- disable being an XDP redirect target by default (same as
other drivers) to avoid wasting resources if feature is
unused
- Meta (fbnic):
- add support for Linux-managed PCS on 25G, 50G, and 100G links
- Wangxun:
- support Rx descriptor merge, and Tx head writeback
- support Rx coalescing offload
- support 25G SPF and 40G QSFP modules
- Ethernet virtual:
- Google (gve):
- allow ethtool to configure rx_buf_len
- implement XDP HW RX Timestamping support for DQ descriptor
format
- Microsoft vNIC (mana):
- support HW link state events
- handle hardware recovery events when probing the device
- Ethernet NICs consumer, and embedded:
- usbnet: add support for Byte Queue Limits (BQL)
- AMD (amd-xgbe):
- add device selftests
- NXP (enetc):
- add i.MX94 support
- Broadcom integrated MACs (bcmgenet, bcmasp):
- bcmasp: add support for PHY-based Wake-on-LAN
- Broadcom switches (b53):
- support port isolation
- support BCM5389/97/98 and BCM63XX ARL formats
- Lantiq/MaxLinear switches:
- support bridge FDB entries on the CPU port
- use regmap for register access
- allow user to enable/disable learning
- support Energy Efficient Ethernet
- support configuring RMII clock delays
- add tagging driver for MaxLinear GSW1xx switches
- Synopsys (stmmac):
- support using the HW clock in free running mode
- add Eswin EIC7700 support
- add Rockchip RK3506 support
- add Altera Agilex5 support
- Cadence (macb):
- cleanup and consolidate descriptor and DMA address handling
- add EyeQ5 support
- TI:
- icssg-prueth: support AF_XDP
- Airoha access points:
- add missing Ethernet stats and link state callback
- add AN7583 support
- support out-of-order Tx completion processing
- Power over Ethernet:
- pd692x0: preserve PSE configuration across reboots
- add support for TPS23881B devices
- Ethernet PHYs:
- Open Alliance OATC14 10BASE-T1S PHY cable diagnostic support
- Support 50G SerDes and 100G interfaces in Linux-managed PHYs
- micrel:
- support for non PTP SKUs of lan8814
- enable in-band auto-negotiation on lan8814
- realtek:
- cable testing support on RTL8224
- interrupt support on RTL8221B
- motorcomm: support for PHY LEDs on YT853
- microchip: support for LAN867X Rev.D0 PHYs w/ SQI and cable diag
- mscc: support for PHY LED control
- CAN drivers:
- m_can: add support for optional reset and system wake up
- remove can_change_mtu() obsoleted by core handling
- mcp251xfd: support GPIO controller functionality
- Bluetooth:
- add initial support for PASTa
- WiFi:
- split ieee80211.h file, it's way too big
- improvements in VHT radiotap reporting, S1G, Channel Switch
Announcement handling, rate tracking in mesh networks
- improve multi-radio monitor mode support, and add a cfg80211
debugfs interface for it
- HT action frame handling on 6 GHz
- initial chanctx work towards NAN
- MU-MIMO sniffer improvements
- WiFi drivers:
- RealTek (rtw89):
- support USB devices RTL8852AU and RTL8852CU
- initial work for RTL8922DE
- improved injection support
- Intel:
- iwlwifi: new sniffer API support
- MediaTek (mt76):
- WED support for >32-bit DMA
- airoha NPU support
- regdomain improvements
- continued WiFi7/MLO work
- Qualcomm/Atheros:
- ath10k: factory test support
- ath11k: TX power insertion support
- ath12k: BSS color change support
- ath12k: statistics improvements
- brcmfmac: Acer A1 840 tablet quirk
- rtl8xxxu: 40 MHz connection fixes/support"
* tag 'net-next-6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1381 commits)
net: page_pool: sanitise allocation order
net: page pool: xa init with destroy on pp init
net/mlx5e: Support XDP target xmit with dummy program
net/mlx5e: Update XDP features in switch channels
selftests/tc-testing: Test CAKE scheduler when enqueue drops packets
net/sched: sch_cake: Fix incorrect qlen reduction in cake_drop
wireguard: netlink: generate netlink code
wireguard: uapi: generate header with ynl-gen
wireguard: uapi: move flag enums
wireguard: uapi: move enum wg_cmd
wireguard: netlink: add YNL specification
selftests: drv-net: Fix tolerance calculation in devlink_rate_tc_bw.py
selftests: drv-net: Fix and clarify TC bandwidth split in devlink_rate_tc_bw.py
selftests: drv-net: Set shell=True for sysfs writes in devlink_rate_tc_bw.py
selftests: drv-net: Use Iperf3Runner in devlink_rate_tc_bw.py
selftests: drv-net: introduce Iperf3Runner for measurement use cases
selftests: drv-net: Add devlink_rate_tc_bw.py to TEST_PROGS
net: ps3_gelic_net: Use napi_alloc_skb() and napi_gro_receive()
Documentation: net: dsa: mention simple HSR offload helpers
Documentation: net: dsa: mention availability of RedBox
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux
Pull printk updates from Petr Mladek:
- Allow creaing nbcon console drivers with an unsafe write_atomic()
callback that can only be called by the final nbcon_atomic_flush_unsafe().
Otherwise, the driver would rely on the kthread.
It is going to be used as the-best-effort approach for an
experimental nbcon netconsole driver, see
https://lore.kernel.org/r/20251121-nbcon-v1-2-503d17b2b4af@debian.org
Note that a safe .write_atomic() callback is supposed to work in NMI
context. But some networking drivers are not safe even in IRQ
context:
https://lore.kernel.org/r/oc46gdpmmlly5o44obvmoatfqo5bhpgv7pabpvb6sjuqioymcg@gjsma3ghoz35
In an ideal world, all networking drivers would be fixed first and
the atomic flush would be blocked only in NMI context. But it brings
the question how reliable networking drivers are when the system is
in a bad state. They might block flushing more reliable serial
consoles which are more suitable for serious debugging anyway.
- Allow to use the last 4 bytes of the printk ring buffer.
- Prevent queuing IRQ work and block printk kthreads when consoles are
suspended. Otherwise, they create non-necessary churn or even block
the suspend.
- Release console_lock() between each record in the kthread used for
legacy consoles on RT. It might significantly speed up the boot.
- Release nbcon context between each record in the atomic flush. It
prevents stalls of the related printk kthread after it has lost the
ownership in the middle of a record
- Add support for NBCON consoles into KDB
- Add %ptsP modifier for printing struct timespec64 and use it where
possible
- Misc code clean up
* tag 'printk-for-6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux: (48 commits)
printk: Use console_is_usable on console_unblank
arch: um: kmsg_dump: Use console_is_usable
drivers: serial: kgdboc: Drop checks for CON_ENABLED and CON_BOOT
lib/vsprintf: Unify FORMAT_STATE_NUM handlers
printk: Avoid irq_work for printk_deferred() on suspend
printk: Avoid scheduling irq_work on suspend
printk: Allow printk_trigger_flush() to flush all types
tracing: Switch to use %ptSp
scsi: snic: Switch to use %ptSp
scsi: fnic: Switch to use %ptSp
s390/dasd: Switch to use %ptSp
ptp: ocp: Switch to use %ptSp
pps: Switch to use %ptSp
PCI: epf-test: Switch to use %ptSp
net: dsa: sja1105: Switch to use %ptSp
mmc: mmc_test: Switch to use %ptSp
media: av7110: Switch to use %ptSp
ipmi: Switch to use %ptSp
igb: Switch to use %ptSp
e1000e: Switch to use %ptSp
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ebiggers/linux
Pull arm64 FPSIMD on-stack buffer updates from Eric Biggers:
"This is a core arm64 change. However, I was asked to take this because
most uses of kernel-mode FPSIMD are in crypto or CRC code.
In v6.8, the size of task_struct on arm64 increased by 528 bytes due
to the new 'kernel_fpsimd_state' field. This field was added to allow
kernel-mode FPSIMD code to be preempted.
Unfortunately, 528 bytes is kind of a lot for task_struct. This
regression in the task_struct size was noticed and reported.
Recover that space by making this state be allocated on the stack at
the beginning of each kernel-mode FPSIMD section.
To make it easier for all the users of kernel-mode FPSIMD to do that
correctly, introduce and use a 'scoped_ksimd' abstraction"
* tag 'fpsimd-on-stack-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiggers/linux: (23 commits)
lib/crypto: arm64: Move remaining algorithms to scoped ksimd API
lib/crypto: arm/blake2b: Move to scoped ksimd API
arm64/fpsimd: Allocate kernel mode FP/SIMD buffers on the stack
arm64/fpu: Enforce task-context only for generic kernel mode FPU
net/mlx5: Switch to more abstract scoped ksimd guard API on arm64
arm64/xorblocks: Switch to 'ksimd' scoped guard API
crypto/arm64: sm4 - Switch to 'ksimd' scoped guard API
crypto/arm64: sm3 - Switch to 'ksimd' scoped guard API
crypto/arm64: sha3 - Switch to 'ksimd' scoped guard API
crypto/arm64: polyval - Switch to 'ksimd' scoped guard API
crypto/arm64: nhpoly1305 - Switch to 'ksimd' scoped guard API
crypto/arm64: aes-gcm - Switch to 'ksimd' scoped guard API
crypto/arm64: aes-blk - Switch to 'ksimd' scoped guard API
crypto/arm64: aes-ccm - Switch to 'ksimd' scoped guard API
raid6: Move to more abstract 'ksimd' guard API
crypto: aegis128-neon - Move to more abstract 'ksimd' guard API
crypto/arm64: sm4-ce-gcm - Avoid pointless yield of the NEON unit
crypto/arm64: sm4-ce-ccm - Avoid pointless yield of the NEON unit
crypto/arm64: aes-ce-ccm - Avoid pointless yield of the NEON unit
lib/crc: Switch ARM and arm64 to 'ksimd' scoped guard API
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ebiggers/linux
Pull 'at_least' array size update from Eric Biggers:
"C supports lower bounds on the sizes of array parameters, using the
static keyword as follows: 'void f(int a[static 32]);'. This allows
the compiler to warn about a too-small array being passed.
As discussed, this reuse of the 'static' keyword, while standard, is a
bit obscure. Therefore, add an alias 'at_least' to compiler_types.h.
Then, add this 'at_least' annotation to the array parameters of
various crypto library functions"
* tag 'libcrypto-at-least-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiggers/linux:
lib/crypto: sha2: Add at_least decoration to fixed-size array params
lib/crypto: sha1: Add at_least decoration to fixed-size array params
lib/crypto: poly1305: Add at_least decoration to fixed-size array params
lib/crypto: md5: Add at_least decoration to fixed-size array params
lib/crypto: curve25519: Add at_least decoration to fixed-size array params
lib/crypto: chacha: Add at_least decoration to fixed-size array params
lib/crypto: chacha20poly1305: Statically check fixed array lengths
compiler_types: introduce at_least parameter decoration pseudo keyword
wifi: iwlwifi: trans: rename at_least variable to min_mode
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ebiggers/linux
Pull crypto library updates from Eric Biggers:
"This is the main crypto library pull request for 6.19. It includes:
- Add SHA-3 support to lib/crypto/, including support for both the
hash functions and the extendable-output functions. Reimplement the
existing SHA-3 crypto_shash support on top of the library.
This is motivated mainly by the upcoming support for the ML-DSA
signature algorithm, which needs the SHAKE128 and SHAKE256
functions. But even on its own it's a useful cleanup.
This also fixes the longstanding issue where the
architecture-optimized SHA-3 code was disabled by default.
- Add BLAKE2b support to lib/crypto/, and reimplement the existing
BLAKE2b crypto_shash support on top of the library.
This is motivated mainly by btrfs, which supports BLAKE2b
checksums. With this change, all btrfs checksum algorithms now have
library APIs. btrfs is planned to start just using the library
directly.
This refactor also improves consistency between the BLAKE2b code
and BLAKE2s code. And as usual, it also fixes the issue where the
architecture-optimized BLAKE2b code was disabled by default.
- Add POLYVAL support to lib/crypto/, replacing the existing POLYVAL
support in crypto_shash. Reimplement HCTR2 on top of the library.
This simplifies the code and improves HCTR2 performance. As usual,
it also makes the architecture-optimized code be enabled by
default. The generic implementation of POLYVAL is greatly improved
as well.
- Clean up the BLAKE2s code
- Add FIPS self-tests for SHA-1, SHA-2, and SHA-3"
* tag 'libcrypto-updates-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiggers/linux: (37 commits)
fscrypt: Drop obsolete recommendation to enable optimized POLYVAL
crypto: polyval - Remove the polyval crypto_shash
crypto: hctr2 - Convert to use POLYVAL library
lib/crypto: x86/polyval: Migrate optimized code into library
lib/crypto: arm64/polyval: Migrate optimized code into library
lib/crypto: polyval: Add POLYVAL library
crypto: polyval - Rename conflicting functions
lib/crypto: x86/blake2s: Use vpternlogd for 3-input XORs
lib/crypto: x86/blake2s: Avoid writing back unchanged 'f' value
lib/crypto: x86/blake2s: Improve readability
lib/crypto: x86/blake2s: Use local labels for data
lib/crypto: x86/blake2s: Drop check for nblocks == 0
lib/crypto: x86/blake2s: Fix 32-bit arg treated as 64-bit
lib/crypto: arm, arm64: Drop filenames from file comments
lib/crypto: arm/blake2s: Fix some comments
crypto: s390/sha3 - Remove superseded SHA-3 code
crypto: sha3 - Reimplement using library API
crypto: jitterentropy - Use default sha3 implementation
lib/crypto: s390/sha3: Add optimized one-shot SHA-3 digest functions
lib/crypto: sha3: Support arch overrides of one-shot digest functions
...
|
|
Merge in late fixes in preparation for the net-next PR.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Switch to use i3c_xfer instead of i3c_priv_xfer because framework will
update to support HDR mode. i3c_priv_xfer is now an alias of i3c_xfer.
Replace i3c_device_do_priv_xfers() with i3c_device_do_xfers(..., I3C_SDR)
to align with the new API.
Prepare for removal of i3c_priv_xfer and i3c_device_do_priv_xfers().
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Matt Johnston <matt@codeconstruct.com.au>
Link: https://patch.msgid.link/20251028-lm75-v1-2-9bf88989c49c@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Save per-channel resources in default, in device and host memory.
As no better API exist, make the XDP-redirect-target SQ available by
loading a dummy XDP program.
This improves the latency of interface up/down operations when feature
is disabled.
Perf numbers:
NIC: Connect-X7.
Setup: 248 channels, default mtu and rx/tx ring sizes.
Interface up + down:
Before: 2.246 secs
After: 1.798 secs (-0.448 sec)
Saves ~1.8 msec per channel.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Reviewed-by: William Tu <witu@nvidia.com>
Link: https://patch.msgid.link/1764497617-1326331-3-git-send-email-tariqt@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The XDP features state might depend of the state of other features, like
HW-LRO / HW-GRO.
In general, move the re-evaluation announcement of the XDP features
(xdp_set_features_flag_locked) into the flow where configuration gets
changed. There's no point in updating them elsewhere.
This is a more appropriate place, as this modifies the announced
features while channels are inactive, which avoids the small interval
between channel activation and the proper setting of the XDP features.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Reviewed-by: William Tu <witu@nvidia.com>
Link: https://patch.msgid.link/1764497617-1326331-2-git-send-email-tariqt@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/zx2c4/wireguard-linux
Jason A. Donenfeld says:
====================
WireGuard updates for Linux 6.19-rc1.
Please find here Asbjørn's ynl series. This has been sitting in my
testing for the last week or so, since he sent out the latest series.
I've dropped the yml sample code, as he found an issue in that last
minute, but otherwise, we've sat on this code for long enough, so
let's see how it goes.
* tag 'wireguard-6.19-rc1-for-jakub' of https://git.kernel.org/pub/scm/linux/kernel/git/zx2c4/wireguard-linux:
wireguard: netlink: generate netlink code
wireguard: uapi: generate header with ynl-gen
wireguard: uapi: move flag enums
wireguard: uapi: move enum wg_cmd
wireguard: netlink: add YNL specification
wireguard: netlink: lower .maxattr for WG_CMD_GET_DEVICE
wireguard: netlink: convert to split ops
wireguard: netlink: use WG_KEY_LEN in policies
wireguard: netlink: validate nested arrays in policy
wireguard: netlink: enable strict genetlink validation
====================
Link: https://patch.msgid.link/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This patch adopts netlink policies and command definitions
generated by ynl-gen, thus completing the conversion to YNL.
Given that the old and new policies are functionally identical
and have just been moved to a new file, it serves to verify
that the policies generated from the spec are identical to the
previous policy code.
The following functions are renamed:
wg_get_device_dump() -> wg_get_device_dumpit()
wg_set_device() -> wg_set_device_doit()
The new files are covered by the existing drivers/net/wireguard/
pattern in MAINTAINERS.
No behavioural changes intended.
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
Use ynl-gen to generate the UAPI header for WireGuard.
The cosmetic changes in this patch confirms that the spec is aligned
with the implementation. By using the generated version, it ensures
that they stay in sync.
Changes in the generated header:
* Trivial header guard rename.
* Trivial white space changes.
* Trivial comment changes.
* Precompute bitflags in ynl-gen (see [1]).
* Drop __*_F_ALL constants (see [1]).
[1] https://lore.kernel.org/r/20251014123201.6ecfd146@kernel.org/
No behavioural changes intended.
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
Use the napi functions napi_alloc_skb() and napi_gro_receive() instead
of netdev_alloc_skb() and netif_receive_skb() for more efficient packet
receiving. The switch to napi aware functions increases the RX
throughput, reduces the occurrence of retransmissions and improves the
resilience against SKB allocation failures.
Signed-off-by: Florian Fuchs <fuchsfl@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20251130194155.1950980-1-fuchsfl@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The "a5psw" tagging protocol uses dsa_xmit_port_mask(), which means
we can offload HSR packet duplication on transmit. Enable that feature.
Cc: "Clément Léger" <clement.leger@bootlin.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20251130131657.65080-14-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The "mtk" tagging protocol uses dsa_xmit_port_mask(), which means we can
offload HSR packet duplication on transmit. Enable that feature.
Cc: Daniel Golle <daniel@makrotopia.org>
Cc: DENG Qingfang <dqfext@gmail.com>
Cc: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Chester A. Unal <chester.a.unal@arinc9.com>
Link: https://patch.msgid.link/20251130131657.65080-13-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The "hellcreek" tagging protocol uses dsa_xmit_port_mask(), which means
we can offload HSR packet duplication on transmit. Enable that feature.
Cc: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20251130131657.65080-12-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The "trailer" tagging protocol uses dsa_xmit_port_mask(), which means we
can offload HSR packet duplication on transmit. Enable that feature.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20251130131657.65080-11-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
