| Age | Commit message (Collapse) | Author |
|---|
|
[Why]
amdgpu_dm_create_validate_stream_for_sink() drove its RGB -> YUV422 ->
YUV420 chroma fallback by recursing and toggling the shared
aconnector->force_yuv420_output / force_yuv422_output fields, resetting
them after each recursive call. Those fields have no locking and the
function runs concurrently on the same connector from two paths: the
connector probe worker (->mode_valid) and a compositor's atomic check
(dm_update_crtc_state). When both run at once, one thread can clear the
override just before the other tests its exit condition, so the exit is
missed and validation loops indefinitely, hanging the modeset path.
[How]
- Replace the recursion with an explicit loop over the chroma encodings
wrapping the existing bpc walk.
- Carry the encoding/bpc selection on the stack, passed by value into
create_stream_for_sink() / fill_stream_properties_from_drm_display_mode(),
instead of mutating shared connector state.
- Derive the supported encodings and bit depths into bitmaps and drive
validation from them, gating each candidate on the sink's advertised
capability so unsupported encodings are never retried.
- Move encoding selection entirely to the caller and pass the chosen
dc_pixel_encoding into fill_stream_properties_from_drm_display_mode().
v2: sqaush in KUnit test fixes, merge with drm-misc changes (Alex)
Assisted-by: Copilot:claude-opus-4.8
Reviewed-by: Jerry Zuo <jerry.zuo@amd.com>
Signed-off-by: Ivan Lipski <ivan.lipski@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
pci_get_slot() returns a referenced PCI device. Commit 44c10138fd4b
("PCI: Change all drivers to use pci_device->revision") replaced a
configuration-space read with direct access to the cached revision field,
but left that access after pci_dev_put(). The bridge may therefore be freed
before its revision is read.
Read the revision before dropping the reference.
Fixes: 44c10138fd4b ("PCI: Change all drivers to use pci_device->revision")
Signed-off-by: Hongyan Xu <getshell@seu.edu.cn>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
|
|
On i.MX8MP, the USB PHY has a dedicated power domain that was previously
never powered off at runtime. With the introduction of runtime PM support,
the power domain will be powered off if the device is runtime suspended,
which breaks USB wakeup functionality.
To preserve wakeup functionality, mark the PHY power domain as runtime
always-on for i.MX8MP platform. To limit the behavior to i.MX8MP, add a
need_genpd_rpm_on to imx8mq_usb_phy_drvdata and set it as true for i.MX8MP.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260731-imx8mp-usb-phy-improvement-v8-6-2ec8d6b3854d@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Replace direct use of phy_ops pointer in of_device_id .data with a
dedicated imx8mq_usb_phy_drvdata structure. This allows per-variant
driver data to be extended in the future without changing the match
table.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://patch.msgid.link/20260731-imx8mp-usb-phy-improvement-v8-5-2ec8d6b3854d@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The CR port is a simple 16-bit data/address parallel port that is
accessed through 32-bit MMIO registers for on-chip access to the
control registers inside the USB 3.0 femtoPHY. Add control register
regmap and export these registers by debugfs to help PHY's diagnostic.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://patch.msgid.link/20260731-imx8mp-usb-phy-improvement-v8-4-2ec8d6b3854d@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Add runtime PM support to ensure the PHY clocks are properly gated
when the PHY is not in use, reducing power consumption.
Clock management is moved from power_on()/power_off() callbacks into
the runtime_resume()/runtime_suspend() callbacks respectively. The PHY
subsystem core already holds a runtime PM reference around init() and
power_on/off() calls, so no explicit clock handling is needed there.
Use devm_clk_get_enabled() and devm_clk_get_optional_enabled() in
probe() to keep clocks enabled initially. This ensures the PHY remains
functional when CONFIG_PM is disabled, where runtime suspend/resume
callbacks are never invoked.
In tca_blk_typec_switch_set(), replace the manual clk_prepare_enable()
/ clk_disable_unprepare() pair with PM_RUNTIME_ACQUIRE_IF_ENABLED() to
guard register access against a concurrently suspended PHY.
Move devm_regulator_get() before pm_runtime_enable() to avoid having
to clean up runtime PM state on regulator acquisition failure.
In remove(), call pm_runtime_get_sync() before pm_runtime_disable() to
ensure the PHY is resumed and clocks are enabled before the devres
teardown disables them.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260731-imx8mp-usb-phy-improvement-v8-3-2ec8d6b3854d@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Set PHY wakeup capable because this PHY supports remote wakeup function.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://patch.msgid.link/20260731-imx8mp-usb-phy-improvement-v8-2-2ec8d6b3854d@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
If probe fails after imx95_usb_phy_get_tca() succeeds, the typec
switch leaks because the only cleanup path was in .remove(), which
never runs on probe failure.
Use devm_add_action_or_reset() so the switch is cleaned up on both
probe failure and driver removal. The imx95_usb_phy_put_tca() is no
longer needed, it will be removed in .remove() too.
Fixes: b58f0f86fd61 ("phy: fsl-imx8mq-usb: add tca function driver for imx95")
Cc: stable@vger.kernel.org
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Xu Yang <xu.yang_2@nxp.com>
Signed-off-by: Felix Gu <ustc.gu@gmail.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://patch.msgid.link/20260731-imx8mp-usb-phy-improvement-v8-1-2ec8d6b3854d@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Has been tested with the following capabilities:
- USB Type-C at 10Gb/s
- DP Alt Mode, using HBR2
- USB Type-C at 480Mb/s + DP Alt Mode, using HBR2
RX and PCS USB tables had to be added, while serdes, TX and PCS tables were
reused from other SoCs.
Some SoCs such as SAR2130P, SM7550, SM7635 and SM8475 use 4nm-v1 PLLs.
For SM8475, trying to use qmp_v6_dp_serdes_tbl structs (which are for
4nm-v1.1 PLLs) causes link training to fail because of ref clock
differences, which in turn makes these structs differ.
Add structs for v1 PLLs as well.
Signed-off-by: Esteban Urrutia <esteuwu@proton.me>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://patch.msgid.link/20260804-sm8475-bup-usbss-v3-2-9a5b9ebf62de@proton.me
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
VBUS regulator
devm_regulator_get_exclusive() initialises the regulator with
enable_count = 1, requiring the consumer to disable it before release.
The devm disable action was previously only registered when the caller
explicitly requested enable, so when the regulator was left in its initial
enabled state without an explicit enable call, the cleanup path skipped
decrementing enable_count, triggering a WARN_ON during regulator
release on device removal.
Fix this by always registering the devm disable action based on the actual
enabled state via regulator_is_enabled(), regardless of whether the
caller requested an explicit enable. This covers both the explicitly
enabled case and the initial state set by devm_regulator_get_exclusive().
Fixes: 24843404efe4 ("phy: renesas: phy-rcar-gen3-usb2: Control VBUS for RZ/G2L SoCs")
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://patch.msgid.link/20260806102236.149159-9-biju.das.jz@bp.renesas.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Add renesas,usb2-phy-r9a08g046 to the OF match table, reusing
rz_g3s_phy_usb2_data as the PHY configuration is shared with RZ/G3S.
While the PHY data is shared, RZ/G3L differs from RZ/G3S in that it has
two OTG controllers, OTG interrupts on port 2, and a controllable
OTG_PERI bit in COMMCTRL for host/device switching on the port 2 USB
controller, which is fixed to host-only on RZ/G3S.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://patch.msgid.link/20260806102236.149159-8-biju.das.jz@bp.renesas.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Add support for the USB3-DP combo PHY found on Hawi platform.
The QMP PHY for Hawi uses QSERDES V10 register layouts. Add the required
PHY sequences from the hardware programming guide and new V10 register
header files. Also add a new v10 offset structure to incorporate the new
COM AON register module.
Signed-off-by: Ronak Raheja <ronak.raheja@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Signed-off-by: Mukesh Ojha <mukesh.ojha@oss.qualcomm.com>
Link: https://patch.msgid.link/20260803091441.3040830-5-mukesh.ojha@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
In cxacru_unbind(), cancel_delayed_work_sync() was conditionally skipped
when poll_state was CXPOLL_STOPPED. However, a work item previously
scheduled when poll_state was CXPOLL_POLLING may still be pending in the
workqueue at the time poll_state transitions to CXPOLL_STOPPED. Skipping
cancel_delayed_work_sync() in this case allows the work to fire after
cxacru_data is freed, causing a use-after-free when cxacru_poll_status()
attempts to acquire instance->poll_state_serialize.
Fix this by always calling cancel_delayed_work_sync() regardless of
poll_state, ensuring no pending or in-flight work can access the freed
instance.
Cc: stable+noautosel@kernel.org # untested fix to a driver init path race
Reported-by: syzbot+24eb38c789655fc43663@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=24eb38c789655fc43663
Signed-off-by: Nguyen Quang Le Kien <khiemtranzo532001@gmail.com>
Link: https://patch.msgid.link/20260803101716.2592486-1-khiemtranzo532001@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If cxacru_cm() encounters an error while submitting or waiting for snd_urb,
it aborts and returns the error without killing the already submitted
rcv_urb. This leaves the rcv_urb active.
When this happens during initialization (e.g., in cxacru_atm_start()), the
driver may ignore the error and proceed to call cxacru_poll_status(), which
invokes cxacru_cm() again. Attempting to submit the still-active rcv_urb
triggers a warning in usb_submit_urb():
cxacru 1-1:1.0: send of cm 0x84 failed (-104)
ATM dev 0: cxacru_atm_start: CHIP_ADSL_LINE_START returned -104
------------[ cut here ]------------
URB ffff88812658d200 submitted while active
WARNING: drivers/usb/core/urb.c:379 at usb_submit_urb+0x79/0x18b0
drivers/usb/core/urb.c:379
...
Call Trace:
<TASK>
cxacru_cm+0x21a/0xf10 drivers/usb/atm/cxacru.c:631
cxacru_cm_get_array drivers/usb/atm/cxacru.c:722 [inline]
cxacru_poll_status+0x178/0x1110 drivers/usb/atm/cxacru.c:828
cxacru_atm_start+0x185/0x360 drivers/usb/atm/cxacru.c:814
usbatm_atm_init+0x144/0x3a0 drivers/usb/atm/usbatm.c:927
usbatm_usb_probe+0x15cb/0x1db0 drivers/usb/atm/usbatm.c:1178
cxacru_usb_probe+0x17f/0x220 drivers/usb/atm/cxacru.c:1370
...
To fix this, ensure that rcv_urb is properly killed if cxacru_cm() aborts
early. We can safely call usb_kill_urb() on rcv_urb in the error path, as
it is safe to call even if the URB is not active (e.g., if it failed to
submit in the first place, or if it already completed).
Cc: stable+noautosel@kernel.org # untested fix to unlikely driver error path
Reported-by: syzbot+c9dff578c3a41775176a@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=c9dff578c3a41775176a
Link: https://syzkaller.appspot.com/ai_job?id=75fec6f2-c8a6-43b1-b184-4d26baba86cc
Signed-off-by: Aleksandr Nogikh <nogikh@google.com>
Link: https://patch.msgid.link/91edfa4c-a63d-400c-9f00-31f3e1f98c00@mail.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
struct macvlan_port is per lower device and is shared by every macvlan
upper on it, including uppers that live in other network namespaces.
Two of its fields are settable over rtnetlink by any upper on the port:
port->bc_cutoff, written by IFLA_MACVLAN_BC_CUTOFF, and
port->bc_queue_len_used, recomputed from IFLA_MACVLAN_BC_QUEUE_LEN.
(port->flags and port->perm_addr are also rtnetlink-settable, but only
in passthru mode, which requires port->count == 0 and so cannot be
reached from a second upper.)
rtnetlink checks CAP_NET_ADMIN against the network namespace the
configured device lives in and nothing else, so once a macvlan has been
moved into a child network namespace, an administrator of that namespace
alone reaches macvlan_changelink(), which applies both attributes
without considering who owns the lower device.
The create path has the same gap. macvlan_common_newlink() resolves a
lower device that is itself a macvlan to the real lower device:
if (netif_is_macvlan(lowerdev))
lowerdev = macvlan_dev_real_dev(lowerdev);
That real device may sit in a network namespace that was never
capability-checked. The new upper then joins its macvlan_port and runs
update_port_bc_queue_len() on it, and, when IFLA_MACVLAN_BC_CUTOFF is
present, update_port_bc_cutoff().
port->bc_cutoff is not a local tuning knob. update_port_bc_cutoff()
recomputes port->bc_filter, which macvlan_handle_frame() tests to decide
whether a multicast frame is deferred to the port broadcast work queue
or flooded inline from the RX softirq, and a negative cutoff clears
bc_filter outright. A namespace that administers none of the other
uppers can therefore change how all of them receive multicast.
Reproduced on 6.8 with a dummy lower device and two macvlan uppers, one
left in the initial namespace and one moved into a child user and
network namespace. From the child, both a changelink and a nested
newlink carrying IFLA_MACVLAN_BC_CUTOFF were accepted, and the value
read back on the initial-namespace sibling followed them, changing from
1 to -7 and then to -42.
Require CAP_NET_ADMIN in the lower device network namespace before
applying a shared port setting or creating a macvlan on a flattened
lower device. rtnl_dev_link_net_capable() short-circuits when the lower
device shares the macvlan network namespace, so an ordinary
single-namespace configuration is unaffected, and per-upper settings
such as mode and flags stay available to an administrator of the
macvlan's own namespace. This is the model ipvlan has used since
commit 7cc9f7003a96 ("ipvlan: disallow userns cap_net_admin to change
global mode/flags").
Found by 0sec automated security-research tooling (https://0sec.ai).
The newlink gate is unconditional rather than keyed on a BC attribute
being present, because joining another namespace's macvlan_port is
itself a mutation of shared state; ipvlan gates ipvlan_link_new() the
same way.
IFLA_MACVLAN_BC_QUEUE_LEN is gated here as well as by any magnitude
check, because the two address different things: a magnitude check
bounds how large a value any caller may request, while this bounds who
may write the shared port at all. update_port_bc_queue_len() takes the
maximum across uppers, so a cross-namespace lowering has no security
effect and this over-rejects it; that is accepted in exchange for one
rule covering every writer of the shared struct.
Cc: stable+noautosel@kernel.org # local DoS by userns are a dime a dozen
Signed-off-by: Doruk Tan Ozturk <doruk@0sec.ai>
Link: https://patch.msgid.link/20260802130137.98105-1-doruk@0sec.ai
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add a bounds check on the global variable modem_index before
using it as an index in sync_wait[] array whose size is NB_MODEM.
Cc: stable+noautosel@kernel.org # untested fix to a driver init path race
Reported-by: syzbot+92f5bf49bf4ac75223ca@syzkaller.appspotmail.com
Tested-by: syzbot+92f5bf49bf4ac75223ca@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=92f5bf49bf4ac75223ca
Signed-off-by: Subasri S <subasris1210@gmail.com>
Link: https://patch.msgid.link/20260802-usb-ueagble-atm-v1-1-340f085b04aa@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
ipheth_sndbulk_callback() re-arms the carrier-check work on any
non-zero URB status:
else
schedule_delayed_work(&dev->carrier_work, 0);
Nothing ties that to the interface being up, so the work can be armed
again after ipheth_close() has already drained it, and stay armed
until the netdev whose private area embeds it is freed.
On unplug with a TX URB in flight, ipheth_disconnect() drains the work
through unregister_netdev() -> ipheth_close() ->
cancel_delayed_work_sync() and only then calls ipheth_kill_urbs().
usb_kill_urb() completes the in-flight TX URB with -ENOENT, so
ipheth_sndbulk_callback() runs after the drain and re-arms
carrier_work.
The same completion also re-arms the work if the interface is only
brought down while a TX URB is in flight, and
ipheth_carrier_check_work() then keeps re-queueing itself once a
second. unregister_netdev() does not call ipheth_close() for an
already-down interface, so nothing drains it on the later unplug
either.
In both cases free_netdev() frees the netdev while carrier_work is
still pending, and ipheth_carrier_check_work() dereferences freed
memory.
Tie the work to the interface state instead of chasing the completion:
disable it in ipheth_close() and enable it in ipheth_open(), so a
schedule_delayed_work() from the URB completion is a no-op whenever
the interface is not up. disable_delayed_work_sync() also waits for a
running instance, so it fully replaces the cancel_delayed_work_sync()
it takes the place of. The work starts out disabled in ipheth_probe()
so the enable/disable counts balance from the first open.
Reproduced under KASAN on linux-next (next-20260731) with dummy_hcd and
raw-gadget standing in for the device, driving the second path above (the
interface is already down, so unregister_netdev() does not call
ipheth_close()): 15 of 15 unpatched boots report a slab-use-after-free in
__run_timers(), freed by ipheth_disconnect() and re-armed from
ipheth_sndbulk_callback() via queue_delayed_work_on(). The
same trigger on a kernel differing only by this patch reports 0 of 15,
and the carrier check still functions across open/close cycles.
The reproducer needs an attached USB device that stops draining bulk OUT,
plus a link down and unplug, driven as root. It is not a privilege
boundary crossing and no exploit primitive was developed.
Found by 0sec (https://0sec.ai).
Fixes: bb1b40c7cb86 ("usbnet: ipheth: prevent TX queue timeouts when device not ready")
Cc: stable@vger.kernel.org
Signed-off-by: Doruk Tan Ozturk <doruk@0sec.ai>
Link: https://patch.msgid.link/20260802120602.42595-1-doruk@0sec.ai
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
tbnet_tear_down() stops both rings and frees their frame buffers before
calling tb_xdomain_disable_paths(). tb_ring_stop() zeroes the ring's
descriptor base and tbnet_free_buffers() unmaps and frees the pages the
frames sit in, so by the time __tb_path_deactivate_hop() polls the hop's
'pending' bit, anything still in flight has nowhere to drain to.
The teardown sequence has been in this order since the driver was added.
The setup path has not: commit ff7cd07f3064 ("net: thunderbolt: Enable
DMA paths only after rings are enabled") moved the path enable to the end
of tbnet_connected_work() and documented why:
/* Both logins successful so enable the rings, high-speed DMA
* paths and start the network device queue.
*
* Note we enable the DMA paths last to make sure we have primed
* the Rx ring before any incoming packets are allowed to
* arrive.
*/
Teardown was never updated to match, so the rings and the paths now come
down in the same order they go up instead of in reverse.
On an ASMedia ASM4242 host router the 'pending' bit then never clears:
every teardown burns the full 500 ms timeout and
__tb_path_deactivate_hop() returns -ETIMEDOUT. Raising the timeout to
5 s does not help, so the hop is not slow to drain, it never drains
at all.
The failure is invisible above the thunderbolt core.
__tb_path_deactivate_hops() is void and only calls tb_port_warn();
tb_path_deactivate(), tb_tunnel_deactivate() and
__tb_disconnect_xdomain_paths() are void as well, and
tb_disconnect_xdomain_paths() ends in an unconditional "return 0". So
tb_xdomain_disable_paths() reports success and the netdev_warn() below
it never fires. Repeated teardowns eventually take the XDomain control
channel down, after which the peer node is gone and only a power cycle
brings the controller back.
Deactivating the paths first fixes it. Measured with kretprobes on a
stock v6.17 tree with no other patches applied, on a link that was up
and had just carried traffic:
before: __tb_path_deactivate_hop() returns 0 for the first hop, then
-ETIMEDOUT for the second 500335 us later
after: 0 for both, 525 us apart
Alternating the two orderings ABBA over three load levels, four
teardowns per arm: every teardown failed before the change (21 of 21
that ran), none failed after (0 of 24). The before arms ran short
because the link died partway through. The same split shows up when
the interface is enslaved to a bond instead of just brought down, which
is how I ran into this in the first place. Throughput and latency after
the change are unchanged.
Hosts whose routers drain the hop despite the stale descriptor base see
no functional difference, since the paths end up deactivated either way.
Fixes: e69b6c02b4c3 ("net: Add support for networking over Thunderbolt cable")
Signed-off-by: Fan XinRan <shinjiangjiang@gmail.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://patch.msgid.link/20260803-b4-tbnet-teardown-v2-1-27de6a13ca2d@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
ptp_clock_register() exposes the clock to userspace. If either following
initialization operation fails, probe returns and devres frees idtfc3 while
the registered clock still refers to the clock information embedded in it.
Complete the fallible initialization before registering the clock. Schedule
the worker after registration because it requires the registered clock.
This removes post-registration failures and avoids exposing a partially
initialized clock.
Cc: stable+noautosel@kernel.org # untested fix to a driver init path race
Co-developed-by: Ijae Kim <ae878000@gmail.com>
Signed-off-by: Ijae Kim <ae878000@gmail.com>
Signed-off-by: Myeonghun Pak <mhun512@gmail.com>
Link: https://patch.msgid.link/20260803135942.48383-1-mhun512@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix sent -> send in the documentation for all variants of
pvr_kccb_send_cmd*().
Signed-off-by: Luigi Santivetti <luigi.santivetti@imgtec.com>
Reviewed-by: Alexandru Dadu <alexandru.dadu@imgtec.com>
Link: https://patch.msgid.link/20260804-staging-pvr-docs-fixes-v2-3-a5a9569a1c1d@imgtec.com
Signed-off-by: Alessio Belle <alessio.belle@imgtec.com>
|
|
Update Rogue heap memory comments to fix typos.
Signed-off-by: Alexandru Dadu <alexandru.dadu@imgtec.com>
Signed-off-by: Luigi Santivetti <luigi.santivetti@imgtec.com>
Reviewed-by: Alessio Belle <alessio.belle@imgtec.com>
Link: https://patch.msgid.link/20260804-staging-pvr-docs-fixes-v2-2-a5a9569a1c1d@imgtec.com
Signed-off-by: Alessio Belle <alessio.belle@imgtec.com>
|
|
Update and remove some old comment in the PVR GEM documentation.
Signed-off-by: Matt Coster <matt.coster@imgtec.com>
Signed-off-by: Luigi Santivetti <luigi.santivetti@imgtec.com>
Reviewed-by: Alessio Belle <alessio.belle@imgtec.com>
Link: https://patch.msgid.link/20260804-staging-pvr-docs-fixes-v2-1-a5a9569a1c1d@imgtec.com
Signed-off-by: Alessio Belle <alessio.belle@imgtec.com>
|
|
All drivers in drivers/s390/block pass clang's compile time context
analysis. Therefore enable CONTEXT_ANALYSIS.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Acked-by: Stefan Haberland <sth@linux.ibm.com>
Link: https://patch.msgid.link/20260806130050.2057443-3-hca@linux.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Disable context analysis for various functions to get rid of context
analysis compile time warnings using clang caused by conditional
locking like e.g.:
drivers/s390/block/dasd_eckd.c:1462:3:
warning: releasing mutex 'dasd_pe_handler_mutex' that was not held [-Wthread-safety-analysis]
1462 | mutex_unlock(&dasd_pe_handler_mutex);
| ^
Use __context_unsafe() to provide a short comment why context analysis is
disabled for each function. It doesn't look like those functions can be
easily reworked to get rid of conditional locking.
Therefore disable context analysis for (only) those functions.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Acked-by: Stefan Haberland <sth@linux.ibm.com>
Link: https://patch.msgid.link/20260806130050.2057443-2-hca@linux.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Allow grouping of individual PCA963x PWM channels into a single
multicolor LED device by adding support for the LED multicolor class.
A child node with sub-children is treated as a multicolor group,
others are treated as single leds, keeping full backwards compatibility.
Signed-off-by: Loic Poulain <loic.poulain@oss.qualcomm.com>
Link: https://patch.msgid.link/20260727-monza-leds-v8-3-6e7e93d44dba@oss.qualcomm.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Add dm_test_crtc_set_static_screen_optimze_sr_entry_psr and
dm_test_crtc_set_static_screen_optimze_psr_su_skips to cover the
allow_sr_entry == true path of amdgpu_dm_crtc_set_static_screen_optimze():
the replay/PSR event updates when psr_version < DC_PSR_VERSION_SU_1, and
skipping the PSR event update when psr_version is DC_PSR_VERSION_SU_1.
Assisted-by: Copilot:Claude-Opus-4.8
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Bhawanpreet Lakha <bhawanpreet.lakha@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Add dm_test_crtc_set_vupdate_irq_dc_busy and
dm_test_crtc_set_vupdate_irq_enable to cover the previously untested
paths in amdgpu_dm_crtc_set_vupdate_irq() where an OTG instance is
assigned: dc_interrupt_set() failing (returns -EBUSY) and succeeding
via a mock IRQ service (returns 0 for enable and disable).
Assisted-by: Copilot:Claude-Opus-4.8
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Bhawanpreet Lakha <bhawanpreet.lakha@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Add dm_test_crtc_handle_vblank_completes_cursor_only to cover the
previously untested branch in amdgpu_dm_crtc_handle_vblank() where a
pending event with pflip_status != AMDGPU_FLIP_SUBMITTED (a cursor-only
commit) is signalled: the vblank event is sent, the vblank reference is
dropped, and acrtc->event is cleared.
Assisted-by: Copilot:Claude-Opus-4.8
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Bhawanpreet Lakha <bhawanpreet.lakha@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Expose amdgpu_dm_crtc_count_crtc_active_planes() for KUnit and add tests
covering the empty plane list and the mixed case exercising the mask
filter, cursor skip, missing plane state, and framebuffer presence
branches.
Assisted-by: Copilot:Claude-Opus-4.8
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Bhawanpreet Lakha <bhawanpreet.lakha@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Expose amdgpu_dm_idle_worker() for KUnit and add tests covering the
disabled exit, both loop break paths, and the enable-body path. Add
dm_kunit_alloc_dc_state() and dm_kunit_alloc_clk_mgr() helpers to
support the new tests.
Assisted-by: Copilot:Claude-Opus-4.8
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Bhawanpreet Lakha <bhawanpreet.lakha@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Add KUnit coverage for the CRTC vblank paths:
- amdgpu_dm_crtc_handle_vblank: no-event completion and the
AMDGPU_FLIP_SUBMITTED guard that keeps a pending event pending.
- amdgpu_dm_crtc_vblank_control_worker: enable increments, disable
decrements, and disable clamps the active vblank IRQ count at zero.
- amdgpu_dm_crtc_disable_vblank: disable path returns cleanly when the
IRQ subsystem is not installed.
Expose amdgpu_dm_crtc_vblank_control_worker for KUnit via
STATIC_IFN_KUNIT/EXPORT_IF_KUNIT and declare it in the header.
Assisted-by: Copilot:Claude-Opus-4.8
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Bhawanpreet Lakha <bhawanpreet.lakha@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Expand KUnit coverage for amdgpu_dm_crtc.c with tests for functions that
are easy to exercise in isolation:
- amdgpu_dm_crtc_set_static_screen_optimze(): the !allow_sr_entry early
return.
- amdgpu_dm_crtc_enable_vblank(): rejection with -EINVAL when enabling
vblank on an unconfigured CRTC.
- amdgpu_dm_crtc_update_crtc_active_planes(): the no-stream branch that
resets active_planes to zero.
- amdgpu_dm_crtc_duplicate_state(): DM-specific fields are carried over.
- amdgpu_dm_crtc_reset_state(): a fresh state is allocated and installed.
- amdgpu_dm_crtc_destroy_state(): a stream-less state is freed cleanly.
Expose amdgpu_dm_crtc_destroy_state(), amdgpu_dm_crtc_duplicate_state(),
amdgpu_dm_crtc_reset_state() and amdgpu_dm_crtc_update_crtc_active_planes()
to the tests via STATIC_IFN_KUNIT/EXPORT_IF_KUNIT.
Assisted-by: Copilot:Claude-Opus-4.8
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Bhawanpreet Lakha <bhawanpreet.lakha@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
transition
[Why]
The seamless mode switch was not getting triggered during HDR to SDR
transitions, and no DPCD write was observed. Root cause analysis
revealed that incorrect panel capabilities were being reported for PSR
SU panels. Due to the wrong capabilities, the OS was not invoking the
seamless mode switch API, resulting in no DPCD communication and also
gated eDP teardown across the seamless mode switch hold.
[How]
Fixed by setting the correct power panel capabilities for PSR SU panels.
This ensures the OS receives accurate panel capability information and
triggers the seamless mode switch API as expected, restoring proper
DPCD writes during HDR to SDR transitions.
The DC commit sequence was tearing the eDP down anyway -- backlight off,
ABM disable, DPMS off, PSR/Replay enable state cleared, PHY TX off,
OTG/OPTC off; all these actions are blocked now with the
skip_implict_edp_power_control
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Karthi Kandasamy <karthi.kandasamy@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHAT]
dc_stream_add_writeback() copies wb_info by value, so free it on all
paths via a single cleanup label. Also bail out early when no pipe_ctx
matches the stream to avoid a NULL pointer dereference.
Assisted-by: Copilot:Claude-Opus-4.8
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
hdmi_frl_status_polling_work() skipped any link whose connector_signal
was not SIGNAL_TYPE_HDMI_FRL. connector_signal is not reliably set to
SIGNAL_TYPE_HDMI_FRL while a link is actually running FRL, so links that
were operating in FRL mode were skipped and their status flags never got
polled, missing link-retrain events.
[How]
Use frl_link_settings.frl_link_rate to decide whether a link is running
FRL. A non-zero rate means FRL is active, so only links with a zero rate
are skipped. This ensures every link actually operating in FRL mode is
polled for status changes.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
VRR info packet previously only supported up to 10-bit refresh rate values
limiting the range of FreeSync minimum and maximum refresh rates that
could be encoded.
[How]
Expanded the bit masking in PB11/PB12 from 2 to 4 bits to capture bits
11:8 of the minimum and maximum FreeSync refresh rates, enabling the VRR
info packet to encode 12-bit refresh rate values.
Reviewed-by: Anthony Koo <anthony.koo@amd.com>
Signed-off-by: Harry VanZyllDeJong <hvanzyll@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
ensure dtbclk is enabled before hdmistreamclk_en
pmfw could stop dtbclk on idle.
driver needs to ensure dtbclk enabled is enabled before hdmistreamclk_en
also disable debounce timer on dcn42.
Reviewed-by: Chris Park <chris.park@amd.com>
Reviewed-by: Leo Chen <leo.chen@amd.com>
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
dm_dp_mst_get_modes() uses drm_connector->index to index the
per-connector HDCP arrays in struct hdcp_workqueue. Those arrays are
sized to AMDGPU_DM_MAX_DISPLAY_COUNT, which matches the DRM connector
index range (0..31). Add a defensive bounds check so that, should the
DRM connector index range ever grow beyond the array size, the access
is skipped instead of reading and writing out of bounds.
Assisted-by: Copilot:claude-opus-4.8
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
AMDGPU_DM_MAX_DISPLAY_INDEX is 31. It suggest a maximum number of
32 connectors. But the way it's used is like MAX_DISPLAY_COUNT.
Hence we're off by one with DRM core, which supports a max of 32
connectors.
Rename AMDGPU_DM_MAX_DISPLAY_INDEX to AMDGPU_DM_MAX_DISPLAY_COUNT
to match its actual use, and increase the size to 32 to match the
originally intended size.
Fixes: 82986fd631fa ("drm/amd/display: save restore hdcp state when display is unplugged from mst hub")
Assisted-by: Copilot:claude-opus-4.8
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Set bits on dword 2 like GFX7-8 except load_global_uconfig
which doesn't exist on GFX6.
Emit VS_PARTIAL_FLUSH before VGT_FLUSH like GFX7-8.
For reference see old PAL which explains the bit fields in
this register and that load_global_uconfig doesn't exist on GFX6
and also see gfx_v7_ring_emit_cntxcntl() for the GFX7 code
which this commit follows.
Fixes: 2cd46ad22383 ("drm/amdgpu: add graphic pipeline implementation for si v8")
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The duplicate amdgpu_dm_plane_test.o entry causes linker errors
during the arm-64 build.
Reviewed-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Check for mmhub0 rather than mmhub1. Looks like a copy
paste typo.
Fixes: d0c989a0aad3 ("drm/amd/amdgpu : Use the MES INV_TLBS API for tlb invalidation on gfx12_1")
Cc: Shaoyun Liu <shaoyun.liu@amd.com>
Reviewed-by: Shaoyun Liu <shaoyun.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
- Add hooks in various entry points to perform hw/sw init for DCN6 asic
- Add dependent changes needed to enable DCN6 asic
- Update the Makefiles so that DCN6 related newly added sources are compiled
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Ivan Lipski <ivan.lipski@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
gpio_led_get_gpiod() returns an error pointer when a platform-data
LED's GPIO is unavailable. gpio_led_probe() skips registration in that
case, but leaves the error pointer in led_dat->gpiod.
The skipped entry remains included in priv->num_leds. During shutdown,
gpio_led_shutdown() walks those entries and passes the error pointer to
gpio_led_set(), producing:
gpiod_set_value: invalid GPIO (errorpointer: -ENOENT)
Clear led_dat->gpiod before skipping the LED so skipped entries do not
retain error-valued descriptors.
Fixes: 45d4c6de4e49 ("leds: gpio: Try to lookup gpiod from device")
Suggested-by: Lee Jones <lee@kernel.org>
Assisted-by: ChatGPT:GPT-5.5-Thinking
Signed-off-by: Steve Dunnagan <sdunnaga@redhat.com>
Reviewed-by: Linus Walleij <linusw@kernel.org>
Link: https://patch.msgid.link/20260724180412.43150-1-sdunnaga@redhat.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Allocate each ring buffer separately. A single allocation summing all
ring sizes can exceed the page allocator's MAX_ORDER limit and fail;
per-ring buffers stay small enough to satisfy. The existing allocation
style doesn't capture any ring data if the huge allocation fails.
Splitting into multiple allocations helps to capture as much data as
possible for the core dump.
A failed ring is left with a NULL buffer and skipped when formatting.
Fixes: eea85914d15b ("drm/amdgpu: save ring content before resetting the device")
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Assisted-by: Claude Code
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The number of rings with outstanding fences can be large, requiring a
bigger allocation. Such allocations don't need to be physically
contiguous, so use kvzalloc/kvcalloc which fall back to vmalloc when
contiguous memory isn't available. This also matches the existing
kvfree used to free these allocations.
Also guard the allocation with ring_count to avoid passing 0 size to
allocation routines.
Fixes: eea85914d15b ("drm/amdgpu: save ring content before resetting the device")
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Add DCN6 code to DC, DML2, and DMUB
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Ivan Lipski <ivan.lipski@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/kvms390/linux into HEAD
KVM: s390: Misc fixes for 7.2
Fix a bunch of small issues that came up during the previous round of
fixes.
They are mostly extremely unlikely races, but they should be fixed
nonetheless.
|
|
Add new headers for:
- dcn 6.0.0
- dpcs 6.0.0
- mmhub 5.0.1
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Ivan Lipski <ivan.lipski@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
On GFX rings, amdgpu_cs_p2_ib() passed user-supplied ib_bytes through
to ib->length_dw without a limit, while ring_emit_ib() encodes length
into packet fields. Oversized values can corrupt adjacent control bits
and destabilize command submission.
Add a per-ring IB packet size limit helper and reject command
submissions exceeding the corresponding dword limit before IB
allocation. Use the documented 20-bit limit for GFX/compute/SDMA/VPE,
and apply the MM fallback limit for other ring types.
Signed-off-by: Candice Li <candice.li@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
