| Age | Commit message (Collapse) | Author |
|---|
|
The ALSA PCM callbacks store the driver state in pcm->private_data. An
open PCM file can outlive USB disconnect because usbtv_audio_free() uses
snd_card_free_when_closed(). The disconnect path can then drop the V4L2
device reference and free struct usbtv before ALSA releases the substream,
so a later close dereferences freed memory in snd_usbtv_pcm_close().
Take a V4L2 device reference for the ALSA card and drop it from the card
private_free callback. This keeps struct usbtv valid until ALSA has closed
the remaining files and freed the card.
Closes: https://lore.kernel.org/r/178144969601.60470.4852887710381872458@gmail.com
Fixes: 63ddf68de52e ("[media] usbtv: add audio support")
Cc: stable@vger.kernel.org
Signed-off-by: Shuangpeng Bai <shuangpeng.kernel@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
|
|
kthread_run() returns an ERR_PTR on failure, not NULL.
When start_streaming() fails, data->kthread_vid_cap is left holding
this error pointer instead of being cleared.
This causes two subsequent bugs:
1. A future call to start_streaming() sees a non-NULL kthread_vid_cap
and returns 0 (success) immediately, without actually starting the
capture thread.
2. A call to stop_streaming() checks 'kthread_vid_cap == NULL' which
is false for an error pointer, and proceeds to call kthread_stop()
on the error pointer, leading to a kernel crash.
Fix this by resetting kthread_vid_cap to NULL on failure before
jumping to the error path.
Fixes: 5cebaac60974 ("media: video-i2c: add video-i2c driver")
Cc: stable@vger.kernel.org
Signed-off-by: Uday Khare <udaykhare77@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
|
|
The Monoprice 106456 (board rev TV22AD-A, also sold as the AnyTV
AUTV002) is a USB ATSC/QAM tuner that enumerates as 05e1:0400 and
reports itself as a "Syntek Semiconductor USB 2.0 Video Capture
Controller". The hardware is an Auvitek AU0828A bridge with an AU8522
demodulator and an NXP TDA18271HDC2 tuner at I2C address 0x60 -- the
same demod/tuner combination as the existing Hauppauge Woodbury board.
Adds board profile and the USB ID so the device binds. The digital
frontend is electrically identical to the Woodbury, so share that
board's au8522/tda18271 configuration and attach path rather than
duplicating it. Tested with over-the-air 8VSB ATSC: it locks and
streams a live 720p transport stream.
Some 05e1:0400 units reportedly ship a Microtune MT2131 tuner with an
AU8502 demodulator instead. This patch does not handle that variant,
but it can't regress it either: 05e1:0400 matches no driver today, and
on the MT2131 units tda18271_attach() just fails, so no frontend is
registered.
Signed-off-by: Joseph Breihan <linux@josephbreihan.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
|
|
dcmipp_runtime_resume() can fail while preparing the device clocks, but
dcmipp_resume() currently ignores the result of
pm_runtime_force_resume() and always returns success.
Return the pm_runtime_force_resume() result so system resume does not
hide a failed runtime resume.
Signed-off-by: Pengpeng Hou <pengpeng@iscas.ac.cn>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
|
|
dcmi_runtime_resume() returns clock enable failures, but dcmi_resume()
currently ignores the result of pm_runtime_force_resume() and always
returns success.
Return the pm_runtime_force_resume() result so system resume does not
hide a failed runtime resume.
Signed-off-by: Pengpeng Hou <pengpeng@iscas.ac.cn>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
|
|
When a device with has_dual_ts=1 is probed and the is_audio_only path
is taken, both dev and dev->dev_next are added to the global
em28xx_devlist via em28xx_init_extension(). However, during disconnect,
em28xx_close_extension(dev) only calls list_del(&dev->devlist), leaving
dev->dev_next->devlist still linked in the global list. When dev_next is
subsequently freed via kref_put(), its devlist entry becomes a dangling
pointer in em28xx_devlist. The next device probe that calls
em28xx_init_extension() triggers a list corruption BUG when list_add_tail
detects the freed node.
This bug was exposed by commit a368ecde8a50 ("USB: core: Fix duplicate
endpoint bug by clearing reserved bits in the descriptor") which clears
reserved bits in bEndpointAddress during endpoint parsing. This causes
fuzzed endpoint addresses like 0xf3 to be normalized to 0x83, which
em28xx interprets as a vendor audio endpoint, enabling the
is_audio_only + has_dual_ts code path that was previously unreachable
with such descriptors.
Fix this by removing dev->dev_next->devlist from the global list in
em28xx_close_extension() before the device is freed.
Fixes: f410b4093fdd ("media: em28xx: split up em28xx_dvb_init to reduce stack size")
Cc: stable@vger.kernel.org
Reported-by: syzbot+99d6c66dbbc484f50e1c@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=99d6c66dbbc484f50e1c
Signed-off-by: Jiangong.Han <jiangong.han@windriver.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
|
|
The byte-alignment paths can call CODE_ADD() with a zero bit
length. The macro then shifts an int by name.b, which can be 32
after the preceding bit was flushed.
vti_bitlen() can likewise shift a signed int into its sign bit while
searching for the bit length, and the package mask construction can
shift by the full type width.
Make zero-length additions a no-op, derive the bit length with fls(),
and build the mask with GENMASK().
Signed-off-by: Yousef Alhouseen <alhouseenyousef@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
|
|
compress_sliced_buf() scans one byte at a time while testing a four-byte
VBI start code. The final iterations can read beyond the remaining
buffer tail.
Stop the scan once fewer than four bytes remain.
Signed-off-by: Pengpeng Hou <pengpeng@iscas.ac.cn>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
|
|
compress_sliced_buf() scans one byte at a time while testing a four-byte
VBI start code. The final iterations can read beyond the remaining
buffer tail.
Stop the scan once fewer than four bytes remain.
Signed-off-by: Pengpeng Hou <pengpeng@iscas.ac.cn>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
|
|
Some pci_device_id arrays already used the PCI_DEVICE macros, others
used named initializers or list initializers. Unify all to use the
PCI_DEVICE macros and (if applicable) a named initializer for
.driver_data. Also drop all zeros that the compiler can care for and
unify indention and spacing.
Signed-off-by: Uwe Kleine-König (The Capable Hub) <u.kleine-koenig@baylibre.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
|
|
The existing tegra_vi_graph_build function relies heavily on a one-to-one
match between Device Tree nodes and media pad links. While this works for
simpler configurations, it causes issues when Device Tree nodes do not
match media pad link logic (e.g., mt9m114). Switch to the
media_entity_get_fwnode_pad helper to verify and retrieve the correct pad
linked to an endpoint, rather than assuming the endpoint ID matches the
pad ID.
Tested-by: Luca Ceresoli <luca.ceresoli@bootlin.com> # tegra20, parallel camera
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
|
|
The driver uses several symbols and structs defined in that header. The
header is currently included transitively via
"vip.h" ->
<media/v4l2-ctrls.h> ->
<media/media-request.h> ->
<media/media-device.h> ->
<linux/platform_device.h>
which seems to be on the lower end of the scale between random and
reliable.
Signed-off-by: Uwe Kleine-König (The Capable Hub) <u.kleine-koenig@baylibre.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
|
|
The av7110_start_feed function contains heavily nested if-statements,
causing excessive indentation and violating code style guidelines.
Refactor the logic inside the DMX_MEMORY_FE case by inverting the
conditional check to break early. Additionally, remove the inner
'if (feed->ts_type & TS_DECODER)' check, as it is redundant since
the outer block already validates this condition.
This reduces the indentation level and cleans up redundant checks
without altering the underlying driver behavior.
Signed-off-by: André Moreira <andrem.33333@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
|
|
fw_log_from_bo() validates the tracing buffer header_size and that the
log fits within the BO, but never checks that log->size is at least
log->header_size. fw_log_print_buffer() then computes:
u32 data_size = log->size - log->header_size;
which underflows to a near-U32_MAX value when firmware reports a log whose
size is smaller than its header. That huge data_size defeats the
log_start/log_end bounds clamps added by commit dd1311bcf0e6 ("accel/ivpu:
Add bounds checks for firmware log indices"), so fw_log_print_lines() reads
far past the small real data region of the BO. A size of 0 also makes
fw_log_from_bo() advance the offset by 0, causing the callers to loop
forever on the same header.
Reject logs whose size is smaller than the header (which also rejects
size == 0).
Fixes: d4e4257afa6e ("accel/ivpu: Add firmware tracing support")
Cc: stable@vger.kernel.org
Signed-off-by: Jhonraushan <raushan.jhon@gmail.com>
Reviewed-by: Karol Wachowski <karol.wachowski@linux.intel.com>
Signed-off-by: Karol Wachowski <karol.wachowski@linux.intel.com>
Link: https://patch.msgid.link/20260715074206.867712-1-raushan.jhon@gmail.com
|
|
All the information for the mode is now stored within
the subdev state, so configure the sensor based on that.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
|
|
The subdev state is now preferred rather than handling crop
and format within the driver state, so switch the driver to
using it.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
|
|
The sensor supports 2 or 4 lane readout, but the driver only allowed
for 4 lanes. Add 2 lane support.
The clock tree only supports single PLL mode to feed both IOP (MIPI)
and IVT (Pixel array).
2 lane mode supports a MIPI link frequency of up to 445MHz (890Mbit/s)
cf 360MHz (720Mbit/s) for 4lane. Update clock setup and pixel rates to
match.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
|
|
In preparation for additional options in the PLL setup, compute
the link frequency rather than using a hardcoded value.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
|
|
This avoids the set_ctrl handler being called under any
circumstances, as it will return an error for the unhandled
ctrl.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
|
|
The difference between frame length and max exposure time in
lines is 10. That had been used as a bare value in calculations.
Move it to a define, and use that define.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
|
|
The colorspace fields were left set to 0 when they should be
set appropriately for a raw image sensor. Add those values.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
|
|
Use the new comon CCI register access helpers to replace the private
register access helpers in the imx355 driver.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
|
|
Avoid powering the sensor up and down unnecessarily by using
pm_runtime's autosuspend_delay feature.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
|
|
Provide all the cropping information via get_selection.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
|
|
fll_min (Frame Length Lines) is set to the same value as fll_def
for all modes, which makes it redundant.
The actual value is also erroneous as the sensor works in all
the defined modes with FLL set at the mode height + 20 lines,
so set the vblank control minimum to 20 rather than varying it.
This also improves the maximum frame rate achievable.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
|
|
The pixel rate is always the same, so there is no need to try and
recompute it in imx355_set_pad_format, and then no need to have the
pointer to it stored.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
|
|
The link_freq_index value in imx355_mode is unused, so remove it.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
|
|
Compute the binning registers based on the difference between
the mode width/height vs the crop width/height.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
|
|
The driver already has the LLP value stored in the mode structure,
but also had the same value set via register writes in the mode's
register list. Remove this duplication.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
|
|
Currently the cropping is set via register entries in the per mode
register lists. Add the crop information to the mode structure as
a v4l2_rect, and set the registers programmatically.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
|
|
Registers 0x0340 and 0x0341 (FRM_LENGTH_LINES) are already written
from the set_ctrl(V4L2_CID_VBLANK) handler, so don't write them
from the mode register list.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
|
|
A large number of registers are identical within all the modes.
Move those to imx355_global_regs.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
|
|
The IMX355 sensor supports multiple external clock frequencies,
including 19.2 MHz and 24 MHz. The driver currently supports only
fixed 19.2 MHz input clock.
Refactor the clock handling to make the PLL configuration dependent
on the external clock frequency and add support for 24 MHz. Introduce
a table of clock parameter sets and program the corresponding EXTCLK
frequency and PLL multipliers to maintain consistent internal VCO
frequencies across supported inputs.
The PLL settings are adjusted so that OP VCO remains at 720 MHz
This preserves existing timing characteristics while allowing systems
using a 24 MHz clock to operate correctly.
No functional change for existing 19.2 MHz users.
Assisted-by: Claude:claude-opus-4-6
Signed-off-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
|
|
If v4l2_async_register_subdev_sensor failed, then the sensor had
already been powered down by pm_runtime_idle, but the error path
then also explicitly called imx355_power_off as well. That left
an imbalance in the regulator and clock calls.
Call pm_runtime_idle only after v4l2_async_register_subdev_sensor
succeeds to avoid this.
Fixes: efa5fe19c0a9 ("media: imx355: Enable runtime PM before registering async sub-device")
Cc: stable@vger.kernel.org
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
|
|
Renesas R-Car S4/V4H/V4M GIC600 integration has address width for AXI
or APB interface configured to 32 bit, it can therefore access only
the first 4 GiB of physical address space. This information comes from
R-Car V4H Interface Specification sheet; there is currently no technical
update number assigned to this limitation. Further input from hardware
engineer indicates that this limitation also applies to R-Car S4 and V4M.
Name the limitation GEN4GICITS1, and add a driver quirk to mitigate this
limitation.
The quirk is keyed on the combination of the GIC implementation
and the platform identification in the device tree.
Co-developed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Acked-by: Thomas Gleixner <tglx@kernel.org>
Link: https://patch.msgid.link/20260707203743.88299-5-marek.vasut+renesas@mailbox.org
|
|
The GIC600 implementation is now known to be used on multiple 64-bit
SoCs, where it has address width for AXI or APB interface configured
to 32 bit, and it can access only the first 4GiB of physical address
space.
Rework the handling of the quirk to work around this limitation such
that new entries can be added purely as new compatible strings, with
no need to add additional functions or new its_quirk array entries.
Suggested-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Link: https://patch.msgid.link/20260707203743.88299-4-marek.vasut+renesas@mailbox.org
|
|
When MSI is enabled but the DWC built-in iMSI-RX is not used, MSI must
be handled via the GIC ITS. Configure all controller MSI registers
accordingly.
Set or clear the MSICAP0 MSIE bit and the PCIEINTSTS0EN MSI_CTRL_INT
bit based on the MSI enable state. Set both bits when MSI is enabled.
Clear both bits when MSI is disabled.
When MSI is disabled, or when MSI is enabled together with iMSI-RX,
clear AXIINTCADDR and AXIINTCCONT to disable any pass through of MSI
TLPs onto the AXI bus and further into the GIC ITS translation
registers.
When MSI is enabled and iMSI-RX is not used, program AXIINTCADDR with
the target address of the GIC ITS translation register, and program
AXIINTCCONT to enable MSI TLP pass through onto the AXI bus and into
the GIC ITS. This configuration allows the GIC ITS to handle MSI
instead of the integrated iMSI-RX.
The driver includes linux/irqchip/arm-gic-v3.h which pulls in headers
which are available only on ARM and ARM64, on other architectures the
headers are not present and the driver fails to build. This driver is
used only on ARM64 hardware, so isolate its build only to ARM64 to avoid
build failures on other architectures.
Co-developed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[mani: commit log and squashed the Kconfig fix:
https://patch.msgid.link/20260714131957.38067-1-marek.vasut+renesas@mailbox.org]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/20260707203743.88299-3-marek.vasut+renesas@mailbox.org
|
|
The helper was introduced in 'commit 8236b0ae31c83 ("bdi: wake up
concurrent wb_shutdown() callers.")' as a generic way of doing the same
sequence of operations:
clear_bit_unlock();
smp_mb__after_atomic();
wake_up_bit();
The helper was first implemented to avoid bugs caused by forgetting to
call `wake_up_bit()` after `clear_bit_unlock()`. Replace the open-coded
sequence with the helper to avoid duplicate code and reduce code paths
to maintain.
Suggested-by: code@agatha.dev
Link: https://kernelnewbies.org/Beginner%20Cleanup%20and%20Refactor%20Tasks%20by%20Agatha%20Isabelle%20Moreira#task_001
Link: https://kernelnewbies.org/Beginner%20Cleanup%20and%20Refactor%20Tasks%20by%20Agatha%20Isabelle%20Moreira#task_002
Signed-off-by: Jiangong.Han <jiangong.han@windriver.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
|
|
nonseekable_open() never fails, so the error check is unnecessary.
Remove the dead error handling path.
Signed-off-by: Bui Duc Phuc <phucduc.bui@gmail.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
|
|
switch_region_table_read() accesses the region table with READ_ONCE()
and is called from the lockless switch_map() IO path. However,
switch_region_table_write() stores to the same array with a plain
assignment. This results in an inconsistent access pattern for a
lockless shared variable and may trigger data race reports.
Use WRITE_ONCE() to pair with the existing READ_ONCE() in
switch_region_table_read().
Cc: stable@vger.kernel.org
Fixes: 99eb1908e643 ("dm switch: factor out switch_region_table_read")
Signed-off-by: Haotian Zhang <vulab@iscas.ac.cn>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
|
|
Add support for the PCIe controller present in the EcoNet EN7528 (and
EN751221) SoCs.
The PCIe controllers present in these SoCs support 2.5 GT/s and 5 GT/s data
rates, but 5 GT/s require re-training after link up.
Co-developed-by: Ahmed Naseef <naseefkm@gmail.com>
Signed-off-by: Ahmed Naseef <naseefkm@gmail.com>
Signed-off-by: Caleb James DeLisle <cjd@cjdns.fr>
[mani: commit log]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://patch.msgid.link/20260702150704.265282-1-cjd@cjdns.fr
|
|
invalidate_cblocks parses cache block numbers with sscanf() and then
stores them in the narrower dm_cblock_t type. Values larger than the
cblock representation are truncated before invalidation, so a request
for one cache block can invalidate a different block.
Checking the parsed value after sscanf() is not sufficient because
sscanf() does not reliably reject values beyond U64_MAX before storing
into the destination. Such inputs can still be converted to a wrapped
u64 value and then pass a later range check.
Split ranges in place and parse each single value or range endpoint
directly with kstrtouint() instead. This rejects malformed values and
values that do not fit in dm_cblock_t before they can be converted to
cblock values. The existing range validation continues to reject empty
or out-of-cache ranges, including the single-value U32_MAX case whose
exclusive end wraps to zero.
Assisted-by: Codex:gpt-5.5-cyber-preview
Signed-off-by: Samuel Moelius <sam.moelius@trailofbits.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Ming-Hung Tsai <mtsai@redhat.com>
|
|
Implement the MES gang contex alloc and free heplers.
Signed-off-by: Prike Liang <Prike.Liang@amd.com>
Reviewed-by: Michael Chen <michael.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Some AMD APU multi-function devices expose an integrated USB xHCI
controller. In some circumstances (such as larger VRAM), the PM core
can resume can fail when the xHCI controller is resuming in parallel
with the GPU/display function.
On affected systems, the xHCI controller can complete pci_pm_resume
and start resuming USB devices while the GPU is still in its much
longer resume path. This race condition leads to USB device resume
failures followed by:
xhci_hcd ...: xHCI host not responding to stop endpoint command
xhci_hcd ...: HC died; cleaning up
Create a device link from any xHCI controller sharing the same PCIe
root port as the APU display function. The link uses DL_FLAG_STATELESS
and DL_FLAG_PM_RUNTIME to ensure the GPU completes its resume before
the xHCI controller begins resuming USB devices.
This device link is done specifically in amdgpu so that if the
platform firmware has been modified such that this issue doesn't happen
the version can be detected and the workaround skipped.
Suggested-by: Aaron Ma <aaron.ma@canonical.com>
Reported-by: mrh@frame.work
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=221073
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Tested-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Tested-by: Alexander F <superveridical@gmail.com>
Tested-by: Francis DB <francisdb@gmail.com>
Link: https://patch.msgid.link/20260713195313.1739762-1-mario.limonciello@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
DCN42B enables DML2 and DML21 by default and defines
dcn42b_prepare_mcache_programming(), but the resource function table only
wires the callback when CONFIG_DRM_AMD_DC_DML21 is defined.
There is no in-tree Kconfig symbol named DRM_AMD_DC_DML21, so the
preprocessor always removes the callback entry. Sibling DCN42 and DCN401
resource tables wire their prepare_mcache_programming callbacks
unconditionally, and the core DC code already checks whether the callback
pointer is present before calling it.
Remove the stale guard so DCN42B exposes the callback relation that its
source and DML21 build world already provide.
This is an RFC patch draft from static conditional callback legality
auditing. It needs AMD display maintainer review before submission as a
final fix.
Signed-off-by: Pengpeng Hou <pengpeng@iscas.ac.cn>
Reviewed-by: George Zhang <george.zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
In dm_update_crtc_state(), the skip_modeset path releases new_stream
via dc_stream_release() but does not set the pointer to NULL.
If a later error (e.g., color management failure) triggers the fail
label, the error path calls dc_stream_release() again on the same
dangling pointer, causing a double release and potential use-after-free.
Fix this by setting new_stream to NULL after the initial release.
Fixes: 9b690ef3c704 ("drm/amd/display: Avoid full modeset when not required")
Signed-off-by: WenTao Liang <vulab@iscas.ac.cn>
Reviewed-by: George Zhang <george.zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
link_dp_irq_handler.c includes "link_dp_panel_replay.h" twice. Drop the
redundant second include; this is a non-functional cleanup flagged by
scripts/checkincludes.pl.
Fixes: 1e5cd4adfc54 ("drm/amd/display: move panel replay out from edp")
Signed-off-by: Anas Khan <anxkhn28@gmail.com>
Reviewed-by: George Zhang <george.zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
dccg35_set_hdmistreamclk_src_new() updates HDMISTREAMCLK_CNTL but
passes DPSTREAMCLK0_SRC_SEL as the field identifier in the second
REG_UPDATE_2 slot.
The current behavior is harmless on DCN3.5 because both fields share the
same bit layout, but it is still incorrect and could break on future
hardware revisions.
Fixes: d36771a03412 ("drm/amd/display: Add DCCG DIO, HPO, OPP, and OPTC support for FRL")
Signed-off-by: Dyllan Kobal <dyllan.kobal@zetier.com>
Reviewed-by: George Zhang <george.zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The final check of hubp for NULL covers all remaining lines of code, since
the value of hubp does not change until the end of the method.
This check is redundant because hubp1 is already dereferenced within the
macro.
If it were NULL, the program would have already failed to proceed.
Remove the left part of the expression with the logical "&&".
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: be1fb44389ca ("drm/amd/display: Check null pointers before used").
Signed-off-by: Gleb Markov <markov.gi@npc-ksb.ru>
Reviewed-by: George Zhang <george.zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
mod_power_create()
kfree() safely handles NULL pointers, so there is no need to check for
NULL before calling kfree().
Remove redundant NULL check.
Found by Coccinelle ifnullfree script.
Signed-off-by: Ziran Zhang <zhangcoder@yeah.net>
Reviewed-by: George Zhang <george.zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
