| Age | Commit message (Collapse) | Author |
|---|
|
The thermal calibration value programmed in efuse is the offset to adjust
thermal value read from hardware, so that output will be accurate.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20260707091056.42771-8-pkshih@realtek.com
|
|
The consumer of rtw89_efuse_read_ecv_be() is in the same ko. No need to
export it.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20260707091056.42771-7-pkshih@realtek.com
|
|
The total number of TX compensation registers is 22, including 7 base and
15 ones according to operating channel.
The v0 is 22 ones per channel. To reduce array size, v1 treats 7 base as
common part across all conditions. However, we can fine tune the base part
to yield better performance, so divide base into two sets according to NSS.
Summarize dimensions as follows
base (7) vals(15)
v0 nss * band * path nss * band * path
v1 1 nss * band * path
v2 nss nss * band * path
Currently, v1 and v2 can present in a file, but only one fw element with
a specific format will be used for specific RFE type.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20260707091056.42771-6-pkshih@realtek.com
|
|
Correct 2.4GHz bandwidth 40MHz bandedge check: pri_ch 5/9 instead of 3/11.
Remove stale 6GHz bandedge case; no restricted band borders 6GHz range.
Signed-off-by: Eric Huang <echuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20260707091056.42771-5-pkshih@realtek.com
|
|
Assert BB reset in the intermediate "switch to 1+1" step of the EMLSR
switch sequence for all three MLO mode transitions by updating the
B_EMLSR_SWITCH_BE4 intermediate value from 0xAFFF to 0x3BAB.
Without the BB reset in this step, the baseband can be left in an
inconsistent state before settling into the final MLO configuration.
Signed-off-by: Eric Huang <echuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20260707091056.42771-4-pkshih@realtek.com
|
|
Add support for path difference based channel smoothing for RTL8922D chip.
This feature measures the ratio of NDP frames and uses a moving average
filter to decide whether to enable beamforming channel smoothing. Tone
index selection is dynamically adjusted based on bandwidth and link mode
(HE/EHT vs VHT). The feature is only enabled for RTL8922D_CID7090 variant.
Signed-off-by: Eric Huang <echuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20260707091056.42771-3-pkshih@realtek.com
|
|
Remove the 40MHz bandwidth compensation from CCK efuse gain calculation.
The design no longer requires the +3dB compensation for 40MHz channels.
Signed-off-by: Eric Huang <echuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20260707091056.42771-2-pkshih@realtek.com
|
|
Co-RX means Wi-Fi & Bluetooth can be able to RX in the same time. This
patch is for judging the Wi-Fi/Bluetooth condition could be Co-RX or not,
and how to set the gain and power.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20260706025445.18428-10-pkshih@realtek.com
|
|
Update WiFi status to each Bluetooth & collect status from the two
Bluetooth adapter by non-stop power zone register. To correct the meaning
of variable, redefine the naming for the variables.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20260706025445.18428-9-pkshih@realtek.com
|
|
Because the two MAC should have their own individual using, they will
need different TDMA mechanism. This patch will bind TDMA with MAC index,
and also the corresponding antenna, hardware grant signal setting.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20260706025445.18428-8-pkshih@realtek.com
|
|
To bind Wi-Fi/Bluetooth with which adapter, in which band.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20260706025445.18428-7-pkshih@realtek.com
|
|
Dual Bluetooth the each of Bluetooth may use different RX gain by their
condition.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20260706025445.18428-6-pkshih@realtek.com
|
|
Dual Bluetooth the each of Bluetooth may use different TX power by their
condition.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20260706025445.18428-5-pkshih@realtek.com
|
|
The mechanism needs information to know which MAC is coexisting with which
Bluetooth and when to enable TDMA with which MAC. So change an variable to
describe the binding target.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20260706025445.18428-4-pkshih@realtek.com
|
|
Separate these two type of initialize entry. Because Wi-Fi power save
leaving will also call the initializing, but don't have to reset all the
stored variables.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20260706025445.18428-3-pkshih@realtek.com
|
|
The version 10 Init info add I/O offload type & variable Bluetooth
function (EX: Zigbee/Thread...etc) into the structure definition.
Firmware need to synchronize these information to do corresponding
setting.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20260706025445.18428-2-pkshih@realtek.com
|
|
If an empty firmware file is supplied via CONFIG_EXTRA_FIRMWARE, the
build currently succeeds but creates an empty section. While the
firmware loader will not return such sections it is better to avoid
adding them in the first place.
Add a compile-time size check to the filechk_fwbin macro to abort the
build early if a 0-size firmware is encountered.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Link: https://patch.msgid.link/20260426043041.649202-2-dmitry.torokhov@gmail.com
[ Use 'exit 1' to properly fail the build. - Danilo ]
Signed-off-by: Danilo Krummrich <dakr@kernel.org>
|
|
Currently, the builtin firmware loader allows 0-size firmware to be
returned successfully to drivers. This differs from all other loading
mechanisms (filesystem, sysfs fallback) which reject 0-byte files, and
forces drivers to add boilerplate size checks.
Modify firmware_request_builtin() to reject 0-size firmware. This will
also result in firmware loader falling back to other mechanisms if an
empty built-in firmware is present.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Link: https://patch.msgid.link/20260426043041.649202-1-dmitry.torokhov@gmail.com
Signed-off-by: Danilo Krummrich <dakr@kernel.org>
|
|
In preparation for removing the strlcat() API[1], replace its uses in
i8042-acpipnpio.h.
i8042_pnp_id_to_string() accumulates a variable number of PNP ids in
a loop, which is what seq_buf is for. The kbd and aux probe functions
build a name from at most three parts that are all known up front, so
the whole construction becomes a single scnprintf() there.
Link: https://github.com/KSPP/linux/issues/370 [1]
Signed-off-by: Ian Bridges <icb@fastmail.org>
Link: https://patch.msgid.link/akyW4xkvCCROM0SE@dev
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
If enabling VIO fails after VDD has been enabled, runtime resume
returns without disabling VDD. Likewise, if device reinitialization
fails, both supplies remain enabled. The runtime PM core keeps the
device suspended when its resume callback fails, so the supplies must
be restored to the suspended state.
Disable the supplies enabled by the callback before returning an error.
Fixes: 97d642e23037 ("iio: light: Add a driver for Sharp GP2AP002x00F")
Assisted-by: Codex:gpt-5
Signed-off-by: Laxman Acharya Padhya <acharyalaxman8848@gmail.com>
Reviewed-by: Linus Walleij <linusw@kernel.org>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jonathan.cameron@oss.qualcomm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
- fix MELFAS MMS114 touchscreen driver to reject invalid touch IDs and
avoid multi-touch slot corruption
- fix a crash in the Sega Dreamcast (Maple) mouse driver when opening
the device, caused by missing driver data
- fixes for Maple drivers (keyboard, mouse, joystick) to properly order
setting driver data and device registration to avoid races
* tag 'input-for-v7.2-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: mms114 - fix multi-touch slot corruption
Input: maple_keyb - set driver data before registering input device
Input: maplecontrol - set driver data before registering input device
Input: maplemouse - set driver data before registering input device
Input: maplemouse - fix NULL pointer dereference in open()
|
|
rpr0521_runtime_suspend() powers the device down and marks the regmap
cache dirty. rpr0521_runtime_resume() syncs the cache before restoring
enabled ALS/PXS channels, but currently ignores a regcache_sync()
failure and can still return success.
Return the regcache_sync() error so resume does not hide a failed
register restore.
Signed-off-by: Pengpeng Hou <pengpeng@iscas.ac.cn>
Signed-off-by: Jonathan Cameron <jonathan.cameron@oss.qualcomm.com>
|
|
vcnl4035_runtime_suspend() marks the regmap cache dirty before runtime
suspend. vcnl4035_runtime_resume() then syncs the cache before re-
enabling ALS, but currently ignores a regcache_sync() failure and can
still report resume success.
Return the regcache_sync() error so the PM core sees the failed register
restore.
Signed-off-by: Pengpeng Hou <pengpeng@iscas.ac.cn>
Signed-off-by: Jonathan Cameron <jonathan.cameron@oss.qualcomm.com>
|
|
m62332_set_value() enables the Vcc regulator on every write of a
non-zero value and disables it on every write of zero, without tracking
the channel's current state. Because the regulator is reference counted,
changing a channel directly from one non-zero value to another enables
it more than once, while a later write of zero disables it only once.
The reference count never returns to zero and the regulator is left
enabled indefinitely.
Only enable the regulator on the transition from zero to non-zero, and
only disable it on the transition from non-zero to zero, using the
previously stored channel value to detect the edge. Balance the
regulator on the I2C error path so the reference count stays consistent
if the write fails.
Fixes: b87b0c0f81e8 ("iio: add m62332 DAC driver")
Reported-by: Sashiko <sashiko-bot@kernel.org>
Closes: https://sashiko.dev/#/patchset/20260418130322.106769-1-erick.henrique.rodrigues%40usp.br
Cc: stable@vger.kernel.org
Signed-off-by: Erick Henrique <erick.henrique.rodrigues@usp.br>
Signed-off-by: Jonathan Cameron <jonathan.cameron@oss.qualcomm.com>
|
|
iio_device_register()
Avoid using devm_iio_device_register(), as this driver requires explicit
error handling and teardown ordering.
With devm_iio_device_register(), IIO device remains registered until the
devres cleanup phase. However, driver's remove() callback removes the
sensor hub callback and trigger support. This can create a race window
where IIO device is still visible and read_raw() requests are issued.
These requests might call sensor_hub_input_attr_get_raw_value(), which
waits up to 5 seconds for a response from the sensor hub callback that
has already been removed.
Add an explicit iio_device_unregister() call in the teardown path to
ensure deterministic cleanup, so that userspace can no longer access the
device once backend resources begin to be dismantled.
Fixes: 59d0f2da3569 ("iio: hid: Add temperature sensor support")
Cc: stable@vger.kernel.org
Reviewed-by: Maxwell Doose <m32285159@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Sanjay Chitroda <sanjayembeddedse@gmail.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jonathan.cameron@oss.qualcomm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mikulas Patocka:
- dm-log: fix overflow on 32-bit machines
- dm-era: fix out of bounds memory access; fix crashes on invalid args
- dm-verity: fix buffer overflow in forward error correction
- dm-thin: fix misbehavior on I/O failures
- dm-pcache: fix NULL pointer dereference on invalid arguments
- dm-inlinecrypt: fix memory leak on error handling
- dm-integrity: fix ignoring the 'fix_hmac' option on device open
- dm: don't store the keyring in memory for a long term
- 12 miscellaneous fixes for bugs found by Claude Opus 4.6
* tag 'for-7.2/dm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm: (23 commits)
dm thin metadata: fix superblock refcount leak on snapshot shadow failure
dm-stats: fix dm_jiffies_to_msec64
dm-stats: fix merge accounting
dm-bufio: fix wrong count calculation in dm_bufio_issue_discard
dm-verity: make error counter atomic
dm-verity: increase sprintf buffer size
dm-verity: fix a possible NULL pointer dereference
dm-verity: avoid double increment of &use_bh_wq_enabled
dm-ioctl: fix a possible overflow in list_version_get_info
dm_early_create: fix freeing used table on dm_resume failure
dm-integrity: fix a bug if the bio is out of limits
dm-integrity: don't increment hash_offset twice
dm-integrity: fix leaking uninitialized kernel memory
dm-integrity: fix the 'fix_hmac' option
dm era: fix error code propagation in era_ctr()
dm era: fix NULL pointer dereference in metadata_open()
dm: avoid leaking the caller's thread keyring via the table device file
dm-inlinecrypt: Fix an error handling path in inlinecrypt_ctr()
dm-pcache: reject option groups without values
dm thin metadata: fix metadata snapshot consistency on commit failure
...
|
|
Add the clocks required to enable the REFGEN block which provides the
reference current to the PHYs in the SoC.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Kathiravan Thirumoorthy <kathiravan.thirumoorthy@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260707-b4-ipq9650_refgen_clocks-v1-2-e070624d03d2@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
With the introduction of sync_state support in the clk and pmdomain
subsystems, the following warning happens when the unused clocks are
shutdown in camcc-sc8280xp:
[ 15.408367] titan_top_gdsc status stuck at 'on'
[ 15.408429] WARNING: drivers/clk/qcom/gdsc.c:178 at gdsc_toggle_logic+0x14c/0x160, CPU#2: kworker/u32:1/14
[ 15.408462] Modules linked in: bnep vfat fat ath11k_pci(+) ath11k mac80211 cfg80211 mhi libarc4 snd_soc_wcd938x snd_soc_wcd938x_sdw snd_soc_wcd_classh hci_uart snd_soc_wcd_common
snd_soc_sc8280xp soundwire_qcom snd_soc_wcd_mbhc snd_soc_qcom_sdw slimbus snd_soc_qcom_common regmap_sdw btqca btrtl qcom_camss soundwire_bus btbcm btintel snd_soc_sdca snd_soc_lpass_wsa_macro
bluetooth snd_soc_lpass_tx_macro snd_soc_lpass_va_macro snd_soc_lpass_rx_macro snd_soc_hdmi_codec snd_soc_lpass_macro_common videobuf2_dma_sg ov5675 v4l2_fwnode videobuf2_memops
qcom_spmi_adc5 snd_soc_core qcom_spmi_adc_tm5 videobuf2_v4l2 snd_seq snd_seq_device videobuf2_common v4l2_async qcom_vadc_common qcom_spmi_temp_alarm pm8941_pwrkey industrialio videodev
snd_compress rfkill ac97_bus snd_pcm_dmaengine qcom_tsens mc qcom_edac snd_pcm pci_pwrctrl_pwrseq qcom_cpufreq_hw snd_timer snd qcomtee soundcore tee leds_gpio joydev binfmt_misc zram
lz4hc_compress governor_simpleondemand panel_edp msm xhci_plat_hcd nvme nvme_core dwc3 qcom_pm8008_regulator
[ 15.408688] ucsi_glink nvme_keyring nvme_auth pmic_glink_altmode udc_core typec_ucsi aux_hpd_bridge qcom_battmgr ulpi ubwc_config socinfo ocmem drm_gpuvm qcom_q6v5_pas drm_exec
qcom_pil_info leds_qcom_lpg gpu_sched led_class_multicolor rtc_pm8xxx qcom_pbs qcom_common drm_display_helper qcom_pon qcom_glink_smem qcom_glink ghash_ce pwrseq_qcom_wcn gpio_sbu_mux
qcom_stats phy_qcom_qmp_combo qcom_q6v5 gf128mul cec dispcc_sc8280xp phy_qcom_edp camcc_sc8280xp i2c_qcom_cci qcom_sysmon drm_dp_aux_bus mdt_loader aux_bridge qcom_pm8008 i2c_hid_of_elan
dwc3_qcom_legacy llcc_qcom icc_bwmon gpi typec qcom_refgen_regulator phy_qcom_qmp_usb nvmem_qfprom qcom_ipcc phy_qcom_snps_femto_v2 gpucc_sc8280xp pinctrl_sc8280xp_lpass_lpi qcom_hwspinlock
pinctrl_lpass_lpi lpasscc_sc8280xp qrtr qcom_aoss pmic_glink pdr_interface phy_qcom_qmp_pcie qcom_smd qcom_pdr_msg icc_osm_l3 qcom_wdt qmi_helpers qcom_rng smp2p rpmsg_core gpio_keys pwm_bl
smem hid_multitouch fuse i2c_dev
[ 15.408928] CPU: 2 UID: 0 PID: 14 Comm: kworker/u32:1 Not tainted 7.1.0+ #2 PREEMPT(lazy)
[ 15.408937] Hardware name: LENOVO 21BX0016US/21BX0016US, BIOS N3HET88W (1.60 ) 03/14/2024
[ 15.408942] Workqueue: pm pm_runtime_work
[ 15.408959] pstate: 60400005 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 15.408967] pc : gdsc_toggle_logic+0x14c/0x160
[ 15.408978] lr : gdsc_toggle_logic+0x14c/0x160
[ 15.408987] sp : ffff8000800f3b40
[ 15.408991] x29: ffff8000800f3b40 x28: 0000000000000000 x27: 0000000000000000
[ 15.409003] x26: 0000000000000000 x25: 0000000000000000 x24: 0000000000000000
[ 15.409014] x23: 0000000000000000 x22: 0000000000000001 x21: ffffa33f298fca88
[ 15.409024] x20: 0000000000000000 x19: ffffa33f298fc5b0 x18: 00cd15db75dacefd
[ 15.409035] x17: 000000040044ffff x16: ffffa33f3b1a3d88 x15: 726f776b80000002
[ 15.409045] x14: ffffffffffffffff x13: 0000000000000028 x12: 0101010101010101
[ 15.409056] x11: 7f7f7f7f7f7f7f7f x10: fefeff3039313274 x9 : ffffa33f3a5edafc
[ 15.409067] x8 : ffff8000800f3780 x7 : 0000000000000001 x6 : 0000000000000001
[ 15.409078] x5 : ffff000bf3ca1288 x4 : 0000000000000000 x3 : ffff5cccb6a3f000
[ 15.409088] x2 : 0000000000000000 x1 : 0000000000000000 x0 : ffff000080ae0000
[ 15.409098] Call trace:
[ 15.409103] gdsc_toggle_logic+0x14c/0x160 (P)
[ 15.409115] gdsc_disable+0x4c/0x190
[ 15.409126] _genpd_power_off+0xa0/0x1a8
[ 15.409137] genpd_power_off.part.0+0x180/0x2a0
[ 15.409149] genpd_runtime_suspend+0x218/0x310
[ 15.409155] __rpm_callback+0x50/0x1f8
[ 15.409166] rpm_callback+0x7c/0x90
[ 15.409175] rpm_suspend+0xe8/0x690
[ 15.409185] pm_runtime_work+0xd0/0xe0
[ 15.409195] process_one_work+0x18c/0x518
[ 15.409208] worker_thread+0x190/0x320
[ 15.409218] kthread+0x110/0x130
[ 15.409227] ret_from_fork+0x10/0x20
This clock is force enabled to be on in the probe, and registered with
the Common Clk Framework, resulting in them being toggled off after
unused clocks are shutdown. This clock is required for the GDSC
transitions.
Similar to the fix in commit b60521eff227 ("clk: qcom: gcc-x1e80100:
Unregister GCC_GPU_CFG_AHB_CLK/GCC_DISP_XO_CLK"), let's just unregister
this clock.
Link: https://lore.kernel.org/linux-clk/20260626-camcc-sc8280xp-titan-top-v1-1-2ca246886493@redhat.com/
Fixes: ff93872a9c616 ("clk: qcom: camcc-sc8280xp: Add sc8280xp CAMCC")
Suggested-by: Jagadeesh Kona <jagadeesh.kona@oss.qualcomm.com>
Signed-off-by: Brian Masney <bmasney@redhat.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20260708-camcc-sc8280xp-remove-gdsc-v1-1-dfaab98a3bf5@redhat.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
critical CBCR registers
The static 'struct qcom_cc_driver_data' and array 'xxx_critical_cbcrs'
are already treated by common.c code as pointers to const, so constify
few remaining pieces.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Taniya Das <taniya.das@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260705171811.115542-4-krzysztof.kozlowski@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
CBCR registers
The static 'struct qcom_cc_desc', 'struct qcom_cc_driver_data' and
array 'xxx_critical_cbcrs' are already treated by common.c code as
pointers to const, so constify few remaining pieces.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Taniya Das <taniya.das@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260705171811.115542-3-krzysztof.kozlowski@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Implement ForLt and CovariantForLt for IoMem<'static, SIZE> and
ExclusiveIoMem<'static, SIZE> so that DevresLt can shorten the stored
'static lifetime back to the caller's borrow lifetime.
CovariantForLt is sound because both types only hold &'a Device<Bound>,
which is covariant over 'a.
Since DevresLt::new() handles the lifetime transmutation internally,
into_devres() no longer needs an explicit transmute to 'static.
Add DevresIoMem<SIZE> and DevresExclusiveIoMem<SIZE> type aliases.
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Link: https://patch.msgid.link/20260626183630.2585057-8-dakr@kernel.org
[ Add default SIZE parameter to DevresIoMem. - Danilo ]
Signed-off-by: Danilo Krummrich <dakr@kernel.org>
|
|
Clock controller drivers are essential for booting up SoCs and are not
really optional for a given platform. Kernel should not ask users
choice of drivers when that choice is obvious and known to the
developers that answer should be 'yes' or 'module'.
Enable drivers for upstreamed or being upstreamed SoCs, which are not
yed enabled in defconfig: Glymur, Hawi, Nord, MSM8976, MSM8998 (GPU CC),
SC7180, SC8180X, SC8280XP, SC7280, SDM660, QDU1000, SM4450, SM7150,
SM8150, SM8450, SM6125, SM6375. Note that main GCC clock controller
drivers are usually already enabled for these.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260703-clk-qcom-defaults-v3-5-78894525e54a@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Clock controller drivers are essential for booting up SoCs and are not
really optional for a given platform. Kernel should not ask users
choice of drivers when that choice is obvious and known to the
developers that answer should be 'yes' or 'module'.
Switch all Qualcomm clock controller drivers which are chosen in
ARM 32-bit qcom defconfig to a default 'yes'.
This has no impact on ARM32 qcom defconfig and ARM64 defconfig
include/generated/autoconf.h, however enables a few drivers for ARM32
multi_v7 defconfig: IPQ_GCC_4019, QCOM_CLK_APCS_SDX55, MSM_LCC_8960,
SDX_GCC_55, QCOM_CLK_RPMH as module, IPQ_GCC_806X, IPQ_LCC_806X and
QCOM_A7PLL. Enabling these on multi_v7 is expected to properly boot
these SoCs with defconfig.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260703-clk-qcom-defaults-v3-4-78894525e54a@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Clock controller drivers are essential for booting up SoCs and are not
really optional for a given platform. Kernel should not ask users
choice of drivers when that choice is obvious and known to the
developers that answer should be 'yes' or 'module'.
Switch all Qualcomm clock controller drivers which are chosen in
defconfig to respective default 'yes' or 'module'.
This has no impact on ARM64 defconfig include/generated/autoconf.h,
however changes few drivers for ARM 32-bit:
1. multi_v7_defconfig: Enable QCOM_CLK_RPMH as module, because SDX55
(ARM 32-bit) uses it.
2. qcom_defconfig: Enable QCOM_A53PLL, QCOM_CLK_APCS_MSM8916 and
MSM_GCC_8916 as built-in, because MSM8916 is also used ARM 32-bit.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260703-clk-qcom-defaults-v3-3-78894525e54a@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
IPQ4019 is ARM 32-bit only SoC and QCOM_A7PLL is used only on SDX55 and
SDX65, which are 32-bit as well.
Do not allow building them for ARM64 to make built kernels smaller and
user choices easier.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260703-clk-qcom-defaults-v3-2-78894525e54a@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Some clock drivers for IPQ5424, IPQ9574, QCM2290, QDU1000 and SA8775
already depend on ARM64. IPQ6018 is ARM64 only SoC (at least upstream)
so should not be a choice for ARM 32-bit builds, to make kernels smaller
and user choices easier.
IPQ_CMN_PLL is used only by the SoCs already having clock controllers
restricted to ARM64
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260703-clk-qcom-defaults-v3-1-78894525e54a@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Rename ForLt to CovariantForLt to prepare for the introduction of a new
ForLt base trait that does not require covariance.
The existing ForLt trait requires covariance, which enables the safe
cast_ref() method. This rename preserves the same semantics under a more
precise name, making room for a weaker ForLt trait in a subsequent
commit.
No functional change.
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Gary Guo <gary@garyguo.net>
Acked-by: Miguel Ojeda <ojeda@kernel.org>
Link: https://patch.msgid.link/20260626183630.2585057-2-dakr@kernel.org
Signed-off-by: Danilo Krummrich <dakr@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/axboe/linux
Pull block fixes from Jens Axboe:
- Limit blk_hctx_poll() to one jiffy. Prevents buggy drivers from
spinning for too long, hence triggering a stalled RCU read section
warning
- Avoid a potential deadlock on zone revalidation failure, which could
otherwise trigger a lockdep circular locking splat during a SCSI disk
rescan
- Remove a redundant GD_NEED_PART_SCAN set in add_disk_final()
- Make writes to queue/wbt_lat_usec honor the WBT enable state
- ublk fix to snapshot the batch commands before preparing IO, so that
userspace can't change an already processed tag and trip the
WARN_ON_ONCE() in the rollback path
- xen-blkfront fix for a double completion of split requests on resume
- drbd fix to reject data replies with an out-of-range payload size
* tag 'block-7.2-20260710' of git://git.kernel.org/pub/scm/linux/kernel/git/axboe/linux:
block: remove redundant GD_NEED_PART_SCAN in add_disk_final()
drbd: reject data replies with an out-of-range payload size
xen-blkfront: fix double completion of split requests on resume
ublk: snapshot batch commands before preparing I/O
block: Make WBT latency writes honor enable state
block: avoid potential deadlock on zone revalidation failure
blk-mq: bound blk_hctx_poll() to one jiffy
|
|
qcom_ebi2_probe() enables the EBI2 clocks manually and populates child
devices manually. Several later failure paths can then return without
disabling the clocks or without relying on the driver core to undo child
population.
Use devm_clk_get_enabled() for both clocks and
devm_of_platform_populate() for children. This lets the driver core
unwind the resources automatically and removes the hand-written error
labels.
Fixes: 335a12754808 ("bus: qcom: add EBI2 driver")
Signed-off-by: Pengpeng Hou <pengpeng@iscas.ac.cn>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Linus Walleij <linusw@kernel.org>
Link: https://lore.kernel.org/r/20260623015415.26975-1-pengpeng@iscas.ac.cn
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
rpmh_rsc_probe() registers CPU PM or genpd notifiers before populating
child devices. If child population fails, the CPU PM notifier path is not
unwound and the genpd path needs open-coded cleanup.
Use devm_pm_runtime_enable() for the genpd path and
devm_add_action_or_reset() for both notifier registrations. This makes
probe failure and driver detach use the same cleanup model while keeping
devm_of_platform_populate() responsible for child devices.
Fixes: 25092e6100ac ("soc: qcom: rpmh-rsc: Attach RSC to cluster PM domain")
Signed-off-by: Pengpeng Hou <pengpeng@iscas.ac.cn>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260623015501.31129-1-pengpeng@iscas.ac.cn
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Allow particular machine accessing eg. efivars.
Signed-off-by: Konstantin Shabanov <mail@etehtsea.me>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260629154812.9066-5-mail@etehtsea.me
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Wire the five tracepoints defined in qcom_scm_trace.h into the SMC
execution path by including the header with CREATE_TRACE_POINTS.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Yuvaraj Ranganathan <yuvaraj.ranganathan@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260522-scm-tracepoints-v2-2-e27cdbe0c585@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
The SCM SMC call path is opaque at runtime. Stalls caused by firmware
congestion, QCOM_SCM_WAITQ_SLEEP/RESUME cycles, and EBUSY retry loops
are invisible without recompiling the kernel with temporary printk
statements or attaching a hardware debugger.
Add five TRACE_EVENTs covering the complete lifecycle of an SCM call:
scm_smc_request
Emit before each arm_smccc_smc_quirk() invocation. Records the
SMC function ID, decoded service and command identifiers, argument
count, and up to six register arguments in hex and decimal. Because
the caller loops on QCOM_SCM_INTERRUPTED, this event fires once per
physical SMC instruction including inte
scm_smc_done
Emit after the outer __scm_smc_do() returns, pairing each
request with its final outcome. Records the SMC function ID, the
kernel error code returned to the caller, and the four firmware
result registers a0-a3.
scm_waitq_sleep
Emit when the firmware returns QCOM_SCM_WAITQ_SLEEP. Records
the wait-queue context and the SMC call context handles required
to issue the matching WAITQ_RESUME.
scm_waitq_resume
Emit just before constructing and sending the WAITQ_RESUME
follow-up call. Records the SMC call context handle being resumed.
scm_waitq_get_wq_ctx
Emit after a successful WAITQ_GET_WQ_CTX fast-call. Records
the returned wait-queue context, flags, and more_pending indicator.
These events let ftrace and perf reconstruct the full sequence of
firmware interactions, measure per-call and end-to-end latency, and
attribute waitqueue stalls to specific service/command pairs without
modifying driver source.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Yuvaraj Ranganathan <yuvaraj.ranganathan@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260522-scm-tracepoints-v2-1-e27cdbe0c585@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Use `io_project!` for PTE array and message queues to restore the proper
encapsulation.
The remaining `dma_read!` and `dma_write!` is now only acting on
primitives; thus replace by `io_read!` and `io_write!`.
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Gary Guo <gary@garyguo.net>
Link: https://patch.msgid.link/20260706-io_projection-v6-17-72cd5d055d54@garyguo.net
Signed-off-by: Danilo Krummrich <dakr@kernel.org>
|
|
`Deref` is automatic and should normally not be used directly.
Also, `IoMem` is going to be implementing `Io` directly, so it will no
longer to be implementing `Deref`.
Reported-by: Andreas Hindborg <a.hindborg@kernel.org>
Link: https://rust-for-linux.zulipchat.com/#narrow/channel/291565-Help/topic/.E2.9C.94.20Projection.20in.20dma.20bus.20address.20space/near/606672061
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Gary Guo <gary@garyguo.net>
Reviewed-by: Daniel Almeida <daniel.almeida@collabora.com>
Link: https://patch.msgid.link/20260706-io_projection-v6-10-72cd5d055d54@garyguo.net
Signed-off-by: Danilo Krummrich <dakr@kernel.org>
|
|
Add support for the camera clock controller for camera clients
to be able to request for camcc clocks on Glymur platform.
Reviewed-by: Taniya Das <taniya.das@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Signed-off-by: Jagadeesh Kona <jagadeesh.kona@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260624-glymur_camcc-v5-2-a321df74b1a1@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
QCOM_SCM and QCOM_SPM are user-selectable drivers, thus
ARM_QCOM_SPM_CPUIDLE should rather avoid selecting them but instead
depend to avoid any possible unmet dependencies.
ARM_QCOM_SPM_CPUIDLE does use symbols from SCM and SPM, and since it
cannot be built-in, the dependency must be as built-in.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260711-qcom-soc-kconfig-v2-4-4a907e064281@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
The drivers for Qualcomm SoC components are covering a basic or
fundamental SoC blocks. Usually they are required for booting or to
achieve basic expected functionality when running Linux. These drivers
do not represent any sort of buses visible to the board
designers/configurators, thus they should be always enabled, regardless
how SoC is used in the final board.
Kernel configuration should not ask users choice of drivers when that
choice is obvious and known to the developers that answer should be
'yes' or 'module'.
Switch most of the Qualcomm SoC drivers to a default 'yes' or
'module' for ARCH_QCOM, to match existing defconfig usage.
This has no impact on arm64 defconfig, arm qcom_defconfig and arm
multi_v7_defconfig.
multi:
+#define CONFIG_QCOM_PDR_HELPERS_MODULE 1
+#define CONFIG_QCOM_PBS_MODULE 1
+#define CONFIG_QCOM_AOSS_QMP 1
+#define CONFIG_QCOM_APR_MODULE 1
+#define CONFIG_QCOM_LLCC_MODULE 1
qcom:
+#define CONFIG_QCOM_PDR_HELPERS_MODULE 1
+#define CONFIG_QCOM_PBS_MODULE 1
+#define CONFIG_QCOM_AOSS_QMP 1
+#define CONFIG_QCOM_APR_MODULE 1
+#define CONFIG_QCOM_SPM 1
+#define CONFIG_QCOM_LLCC_MODULE 1
The change will however enable by default all drivers for arm or arm64
COMPILE_TEST builds, whenever ARCH_QCOM is selected, which feels
logical: if one selects ARCH_QCOM then probably by default wants to
build test it entirely. Kernels with COMPILE_TEST are not supposed to
be used for booting.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260711-qcom-soc-kconfig-v2-3-4a907e064281@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
There is no point to allow selecting core SoC drivers for Qualcomm ARMv7
SoCs when building ARM64 kernel, and vice versa.
This makes kernel configuration more difficult as many do not remember
the Qualcomm SoCs model names/numbers and their properties like
architecture. No features should be lost because:
1. There won't be a single image for ARMv7 and ARMv8/9 SoCs.
2. Newer ARMv8/9 SoCs won't be running in arm32 emulation mode.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260711-qcom-soc-kconfig-v2-2-4a907e064281@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Switch from a simple menu to menuconfig, so all Qualcomm SoC drivers
will be under one selectable option, allowing to disable them all which
should make kernel configuration easier when preparing a non-Qualcomm
kernel.
This has few benefits (functional impact of this commit):
1. Allow compile testing of QCOM_OCMEM, which previously required
ARCH_QCOM.
2. Hide behind ARCH_QCOM or COMPILE_TEST drivers specific to Qualcomm
which should not be available to other kernel builds:
QCOM_PMIC_PDCHARGER_ULOG, QCOM_PMIC_GLINK, QCOM_SPM and QCOM_PBS.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260711-qcom-soc-kconfig-v2-1-4a907e064281@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
