| Age | Commit message (Collapse) | Author |
|---|
|
iforce_process_packet() handles a status report (packet id 0x02) by
taking a force-feedback effect index straight from the device wire and
using it to address the per-effect state array:
i = data[1] & 0x7f;
if (data[1] & 0x80) {
if (!test_and_set_bit(FF_CORE_IS_PLAYED,
iforce->core_effects[i].flags))
...
} else if (test_and_clear_bit(FF_CORE_IS_PLAYED,
iforce->core_effects[i].flags)) {
...
}
The index is masked only with 0x7f, so it ranges 0..127, but
core_effects[] holds only IFORCE_EFFECTS_MAX (32) entries. For an index
of 32..127 the test_and_set_bit()/test_and_clear_bit() is an
out-of-bounds single-bit read-modify-write past the array. core_effects[]
is the second-to-last member of struct iforce, so the write lands in the
trailing members and beyond the embedding kzalloc()'d iforce_serio /
iforce_usb object.
data[1] is unvalidated device payload on both transports (the USB
interrupt endpoint and serio), and the status path is not gated on force
feedback being present, so a malicious or counterfeit device can set or
clear a bit at an attacker-chosen offset past the object.
Reject an out-of-range index instead of indexing with it. Bound against
the array dimension IFORCE_EFFECTS_MAX rather than dev->ff->max_effects so
the check guarantees memory safety regardless of how many effects the
device registered. A legitimate "effect started/stopped" status always
carries an index below IFORCE_EFFECTS_MAX, so well-formed devices are
unaffected; the neighbouring mark_core_as_ready() loop is already bounded
and is left untouched.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Bryam Vargas <hexlabsecurity@proton.me>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20260613-b4-disp-4828d263-v1-1-02320e1a89dd@proton.me
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
goodix_ts_read_input_report() copies the number of touch points reported
by the device into an on-stack buffer
u8 point_data[2 + GOODIX_MAX_CONTACT_SIZE * GOODIX_MAX_CONTACTS];
which is sized for at most GOODIX_MAX_CONTACTS (10) contacts. The only
runtime check bounds the per-interrupt count against ts->max_touch_num,
but that value is taken verbatim from a 4-bit field of the device
configuration block and is never clamped:
ts->max_touch_num = ts->config[MAX_CONTACTS_LOC] & 0x0f;
The nibble can be 0..15, so a malfunctioning, malicious or counterfeit
controller (or an attacker tampering with the I2C bus) can advertise up
to 15 contacts. goodix_ts_read_input_report() then accepts a touch_num
of up to 15 and the second goodix_i2c_read() writes
ts->contact_size * (touch_num - 1) bytes past the one-contact header into
point_data - up to 30 bytes (45 with the 9-byte report format) beyond the
92-byte buffer: a stack out-of-bounds write.
Clamp max_touch_num to GOODIX_MAX_CONTACTS, the number of contacts
point_data[] is sized for, when reading it from the configuration.
Fixes: a7ac7c95d468 ("Input: goodix - use max touch number from device config")
Cc: stable@vger.kernel.org
Signed-off-by: Bryam Vargas <hexlabsecurity@proton.me>
Reviewed-by: Hans de Goede <johannes.goede@oss.qualcomm.com>
Link: https://patch.msgid.link/20260612-b4-disp-6844625d-v1-1-df0aed080c9d@proton.me
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
KCSAN report a race in break_stripe_batch_list() vs. raid5_make_request()
on sh->dev[i].flags (plain word write vs. atomic bit op)..
and .. one possible scenario is:
CPU1 CPU2
break_stripe_batch_list(sh1)
-> handle sh2
-> lock(sh2)
-> sh2->batch_head = NULL
-> unlock(sh2)
-> test_and_clear_bit(R5_Overlap, sh2->dev[i].flags)
-> wake_up_bit(sh2->dev[i].flags)
raid5_make_request()
-> add_all_stripe_bios(sh2)
-> lock(sh2)
-> stripe_bio_overlaps(sh2) returns true
batch_head is NULL, so new bio overlap
exist bio on sh2 -> true
-> set_bit(R5_Overlap, sh2->dev[i].flags)
-> unlock(sh2)
-> wait_on_bit(sh2->dev[i].flags)
-> sh2->dev[i].flags = sh1->dev[i].flags & ~R5_Overlap
No wait_up_bit(), CPU2 could be wait_on_bit() forever...
Fix by :
- Expand the protect zone.
- Use batch_head's device flag's snaphot when no held head_sh->stripe_lock.
- Move sh/head_sh->batch_head = NULL to the end of protected zone , and ,
any concurrent add_all_stripe_bios() grabs sh->stripe_lock now either:
- see batch_head != null, and , is rejected by stripe_bio_overlaps()
under the lock (no R5_Overlap wait ) , or ,
- sees batch_head == NULL, only after dev[i].flags has already been
set and the prior R5_Overlap waiters worken.
KCSAN report:
================================================
BUG: KCSAN: data-race in break_stripe_batch_list / raid5_make_request
write (marked) to 0xffff8e89c8117548 of 8 bytes by task 4042 on cpu 0:
raid5_make_request+0xea0/0x2930
md_handle_request+0x4a2/0xa40
md_submit_bio+0x109/0x1a0
__submit_bio+0x2ec/0x390
submit_bio_noacct_nocheck+0x457/0x710
submit_bio_noacct+0x2a7/0xc20
submit_bio+0x56/0x250
blkdev_direct_IO+0x54c/0xda0
blkdev_write_iter+0x38f/0x570
aio_write+0x22b/0x490
io_submit_one+0xa51/0xf70
__x64_sys_io_submit+0xf7/0x220
x64_sys_call+0x1907/0x1c60
do_syscall_64+0x130/0x570
entry_SYSCALL_64_after_hwframe+0x76/0x7e
read to 0xffff8e89c8117548 of 8 bytes by task 4010 on cpu 5:
break_stripe_batch_list+0x249/0x480
handle_stripe_clean_event+0x720/0x9b0
handle_stripe+0x32fb/0x4500
handle_active_stripes.isra.0+0x6e0/0xa50
raid5d+0x7e0/0xba0
md_thread+0x15a/0x2d0
kthread+0x1e3/0x220
ret_from_fork+0x37a/0x410
ret_from_fork_asm+0x1a/0x30
value changed: 0x0000000000000019 -> 0x0000000000000099 --> R5_Overlap
Fixes: fb642b92c267 ("md/raid5: duplicate some more handle_stripe_clean_event code in break_stripe_batch_list")
Signed-off-by: Chen Cheng <chencheng@fnnas.com>
Link: https://patch.msgid.link/20260619041013.1207148-1-chencheng@fnnas.com
Signed-off-by: Yu Kuai <yukuai@fygo.io>
|
|
The patch just suppress KCSAN noise. No functional change.
RAID-5 can group multi full-stripe-write aka stripe_head into a
batch aka batch_list, with one head_sh leading them. Call
break_stripe_batch_list() when the batch is finished, or,
a stripe has to be dropped out of the batch.
break_stripe_batch_list() reads stripe state several times while
request paths can update thost state words concurrently with
lockless bitops, which reported by KCSAN.
Use a snapshot to guarantees that the value used for
warning, copying, and handle checks is internally consistent
at current read moment.
KCSAN report:
==============================================
BUG: KCSAN: data-race in __add_stripe_bio / break_stripe_batch_list
write (marked) to 0xffff8e89d4f0b988 of 8 bytes by task 4323 on cpu 3:
__add_stripe_bio+0x35e/0x400
raid5_make_request+0x6ac/0x2930
md_handle_request+0x4a2/0xa40
md_submit_bio+0x109/0x1a0
__submit_bio+0x2ec/0x390
submit_bio_noacct_nocheck+0x457/0x710
submit_bio_noacct+0x2a7/0xc20
submit_bio+0x56/0x250
blkdev_direct_IO+0x54c/0xda0
blkdev_write_iter+0x38f/0x570
aio_write+0x22b/0x490
io_submit_one+0xa51/0xf70
read to 0xffff8e89d4f0b988 of 8 bytes by task 4290 on cpu 4:
break_stripe_batch_list+0x3ce/0x480
handle_stripe_clean_event+0x720/0x9b0
handle_stripe+0x32fb/0x4500
handle_active_stripes.isra.0+0x6e0/0xa50
raid5d+0x7e0/0xba0
Signed-off-by: Chen Cheng <chencheng@fnnas.com>
Link: https://patch.msgid.link/20260618134748.1168360-1-chencheng@fnnas.com
Signed-off-by: Yu Kuai <yukuai@fygo.io>
|
|
In airoha_qdma_set_chan_tx_sched(), the loop clearing queue mask was
using AIROHA_NUM_TX_RING (32) instead of AIROHA_NUM_QOS_QUEUES (8).
Each channel has 8 queues, and TXQ_DISABLE_CHAN_QUEUE_MASK(channel, i)
computes BIT(i + (channel * 8)). With i ranging 0..31, this causes:
- channel 0: clears bit 0..31 (all 4 channels) instead of 0..7
- channel 1: clears bit 8..31 (channels 1-3) instead of 8..15
- channel 2: clears bit 16..31 (channels 2-3) instead of 16..23
- channel 3: clears bit 24..31 (channel 3 only) - correct by accident
While BIT(32+) on arm64 produces 64-bit values truncated to 0 in u32
mask parameter, the loop still incorrectly clears queues within the
same channel beyond queue 7.
Even though this is functionally harmless (the register resets to 0
and is only ever cleared, never set — so clearing extra bits is a
no-op), the loop bound is semantically wrong and should be fixed for
correctness and clarity.
Fix by using AIROHA_NUM_QOS_QUEUES (8) as the loop upper bound.
Fixes: ef1ca9271313 ("net: airoha: Add sched HTB offload support")
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Wayen Yan <win847@gmail.com>
Link: https://patch.msgid.link/178187479434.2400840.1312143943526335838@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If the allocation of fp[i].tpa_info fails, the error path will not free
the struct bnx2x_fastpath allocated earlier, as it is not linked to the
bp structure yet. Fix that by linking it immediately after allocation.
Cc: stable@vger.kernel.org
Fixes: 15192a8cf8a8 ("bnx2x: Split the FP structure")
Signed-off-by: Abdun Nihaal <nihaal@cse.iitm.ac.in>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260620062402.89549-1-nihaal@cse.iitm.ac.in
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Kernel selftests wait 1.25x of the promised stats refresh time
(as read from ethtool -c). bnxt reports 1sec by default, but
the stats update process has two steps. First device DMAs the
new values, then the service task performs update in full-width
SW counters. So the worst case delay is actually 2x.
Note that the behavior is different for ring stats and port stats.
Port stats are fetched synchronously by the service worker, so
there's no risk of doubling up the delay there.
The problem of stale stats impacts not only tests but real workloads
which monitor egress bandwidth of a NIC. The inaccuracy causes double
counting in the next cycle and spurious overload alarms.
Try to read from the DMA buffer more aggressively, to mitigate
timing issues between DMA and service task. The SW update should
be cheap.
Fixes: 51f307856b60 ("bnxt_en: Allow statistics DMA to be configurable using ethtool -C.")
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20260619191538.104165-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Each PPP control protocol (LCP/IPCP/IPV6CP) embedded in struct ppp
registers a timer via timer_setup(). That struct ppp is the
hdlc->state allocation, which detach_hdlc_protocol() frees with kfree()
in both teardown paths: unregister_hdlc_device() and the re-attach inside
attach_hdlc_protocol().
The ppp proto never registered a .detach callback, so
detach_hdlc_protocol() performs no timer synchronization before the
kfree(). The only cancel, timer_delete(&proto->timer) in ppp_cp_event(),
is partial (it does not wait for a running callback) and only runs on the
->CLOSED transition; ppp_stop()/ppp_close() do not sync either. A
ppp_timer callback already executing (blocked on ppp->lock) survives the
kfree and then dereferences proto->state / ppp->lock in freed memory,
leading to a use-after-free.
Fix this by adding a .detach helper that calls timer_shutdown_sync() on
every per-proto timer. detach_hdlc_protocol() invokes proto->detach(dev)
before kfree(hdlc->state), so timer_shutdown_sync()
now runs on both free paths.
timer_shutdown_sync() is used instead of timer_delete_sync() because the
keepalive path re-arms the timer through add_timer()/mod_timer() and
shutdown blocks any re-activation during teardown.
Initialize the per-protocol timers in ppp_ioctl() when the protocol is
attached, and remove the now-redundant timer_setup() from ppp_start(), so
that the timers are initialized exactly once at attach time and
ppp_timer_release() never operates on uninitialized timer_list
structures. attach_hdlc_protocol() uses kmalloc() (not kzalloc), so
struct ppp's protos[i].timer is uninitialized garbage until the first
timer_setup(); without this init-at-attach, attaching the PPP protocol
without ever bringing the device up would leave timer_shutdown_sync()
operating on uninitialized memory in .detach. Moving the init out of
ppp_start() (which only runs on NETDEV_UP) into the attach path makes the
initialization unconditional and avoids initializing the same timer_list
twice.
This bug was found by static analysis.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Signed-off-by: Fan Wu <fanwu01@zju.edu.cn>
Link: https://patch.msgid.link/20260617020518.116319-1-fanwu01@zju.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
icssg_ndo_get_stats64() unconditionally calls emac_get_stat_by_name()
with FW PA stat names regardless of whether the PA stats block is
present on the hardware. emac_get_stat_by_name() already guards the
PA stats lookup with `if (emac->prueth->pa_stats)`; when that pointer
is NULL the lookup falls through to netdev_err() and returns -EINVAL.
Because ndo_get_stats64 is polled regularly by the networking stack
this produces thousands of log entries of the form:
icssg-prueth icssg1-eth end0: Invalid stats FW_RX_ERROR
A secondary consequence is that the int(-EINVAL) return value is
implicitly widened to a near-ULLONG_MAX unsigned value when accumulated
into the __u64 fields of rtnl_link_stats64, silently corrupting the
rx_errors, rx_dropped and tx_dropped counters reported by `ip -s link`.
Every other PA-aware code path in the driver is already guarded with
the same `if (emac->prueth->pa_stats)` check. Apply the same guard
here.
Fixes: 0d15a26b247d ("net: ti: icssg-prueth: Add ICSSG FW Stats")
Signed-off-by: Philippe Schenker <philippe.schenker@impulsing.ch>
Reviewed-by: Simon Horman <horms@kernel.org>
Cc: danishanwar@ti.com
Cc: rogerq@kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20260618093037.3448858-1-dev@pschenker.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In ofdpa_port_fdb(), the hash_del() only unlinks the node from
hash table, but does not free it.
Fix this by adding kfree(found) after the !found == removing check,
where the pointer value is no longer needed.
Found by Coccinelle kfree script.
Cc: <stable+noautosel@kernel.org> # rocker is a test harness, it's never loaded on production systems
Signed-off-by: Ziran Zhang <zhangcoder@yeah.net>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20260616013245.7098-1-zhangcoder@yeah.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add PM suspend/resume callbacks to enable/disable IRQ wake for the
RTC alarm interrupt. This allows the RTC alarm to wake the system
from STR (e.g. via rtcwake -m mem -s N).
Without this, the RTC IRQ is masked during suspend by the MPIC's
IRQCHIP_MASK_ON_SUSPEND behavior, preventing alarm-based wakeup.
Signed-off-by: Xue Lei <Xue.Lei@windriver.com>
Link: https://patch.msgid.link/20260611023350.1370881-1-Xue.Lei@windriver.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Add support for matching the RTC controller on ASPEED AST2700 SoCs.
The AST2700 RTC controller is compatible with the existing ASPEED
RTC driver implementation.
Signed-off-by: Tommy Huang <tommy_huang@aspeedtech.com>
Link: https://patch.msgid.link/20260601-ast2700-rtc-v1-2-15d4ca46500a@aspeedtech.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Fix spelling of 'occurence' to 'occurrence' and 'of' to 'or' in the
kernel-doc comment for rtc_handle_legacy_irq().
Signed-off-by: Yahya Saqban <yahyasaqban@gmail.com>
Link: https://patch.msgid.link/20260512210235.343070-1-yahyasaqban@gmail.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
msc313_rtc_probe() calls devm_request_irq() with IRQF_SHARED and
&pdev->dev as the cookie, but platform_set_drvdata() is only called
later after the clock setup. With a shared IRQ line, another device
on the same line can trigger the handler in that window. The
handler does dev_get_drvdata() on the cookie, gets NULL, and
dereferences priv->rtc_base in interrupt context.
Pass priv as the cookie directly so the handler reads it from
dev_id without the lookup, removing the dependency on probe order.
Fixes: be7d9c9161b9 ("rtc: Add support for the MSTAR MSC313 RTC")
Signed-off-by: Stepan Ionichev <sozdayvek@gmail.com>
Link: https://patch.msgid.link/20260511032703.48262-1-sozdayvek@gmail.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
The platform was removed a few years ago, and the mfd driver
is also gone now, so it is impossible to build or use it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://patch.msgid.link/20260527193927.3523952-1-arnd@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Add a new function rtc_read_next_alarm() that reads the next expiring
alarm from the RTC timerqueue. This is different from rtc_read_alarm(),
which only reads the aie_timer.
The wakealarm sysfs file programs the rtc->aie_timer, whereas the
alarmtimer suspend routine programs its own timer into the RTC timerqueue.
Both timers end up in the RTC's timerqueue, and the first expiring timer
is what gets armed in the hardware.
This new function allows code to query which alarm will actually fire
next, regardless of which subsystem programmed it. This is needed by
platform code that needs to program secondary timers based on the
actual next wakeup time.
Link: https://lore.kernel.org/all/87ed50z0le.ffs@tglx
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Assisted-by: Claude:claude-opus-4-6
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://patch.msgid.link/20260521043714.1022930-2-mario.limonciello@amd.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
nbd_reclassify_socket() warns via WARN_ON_ONCE() if the socket lock is
held at the point of reclassification. That assertion was copied from
nvme-tcp, where the socket is created internally by the kernel
(sock_create_kern()) and is never visible to user space, so the lock
is guaranteed to be free.
NBD is different: the socket is looked up from a user-supplied fd in
nbd_get_socket(), and user space retains that fd. A concurrent syscall
on the same socket (or softirq processing taking bh_lock_sock() on a
connected TCP socket) can legitimately hold the lock at the instant
NBD reclassifies it. sock_allow_reclassification() then returns false
and the WARN_ON_ONCE() fires, which turns into a crash under
panic_on_warn. This is reachable by simply racing NBD_CMD_CONNECT
against socket activity on the same fd, as reported by syzbot.
Hitting a held lock here is expected for an externally owned socket and
is not a kernel bug, so skip reclassification silently instead of
warning. Reclassification is a lockdep-only annotation, so skipping it
in the rare racing case is harmless.
Reported-by: syzbot+6b85d1e39a5b8ed9a954@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=6b85d1e39a5b8ed9a954
Fixes: d532cddb6c60 ("nbd: Reclassify sockets to avoid lockdep circular dependency")
Signed-off-by: Deepanshu Kartikey <kartikey406@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20260621235255.66015-1-kartikey406@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Commit 3c7bf5af21960 ("e1000e: Introduce private flag to disable K1")
disabled K1 by default on Meteor Lake and newer systems due to packet
loss observed on various platforms. However, disabling K1 caused an
increase in power consumption.
To mitigate this, reconfigure the PLL clock gate value so that K1 can
remain enabled without incurring the additional power consumption.
Re-enable K1 by default, but keep the private flag to support disabling
it via ethtool. Additionally, introduce a DMI quirk table, so that K1 may
be disabled by default on known problematic systems. Currently, this
includes the Dell Pro 16 Plus, where the issue has been reported to persist
despite the changes to the PLL lock timeout.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=220954
Link: https://lists.osuosl.org/pipermail/intel-wired-lan/Week-of-Mon-20250623/048860.html
Link: https://lists.osuosl.org/pipermail/intel-wired-lan/Week-of-Mon-20260330/054059.html
Signed-off-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Co-developed-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Signed-off-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Fixes: 3c7bf5af21960 ("e1000e: Introduce private flag to disable K1")
Tested-by: Moriya Kadosh <moriyax.kadosh@intel.com>
Tested-by: Todd Brandt <todd.e.brandt@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
i40e_debug() macro takes struct i40e_hw *h as first argument. But the
macro body uses hw instead of h. This has been working so far because hw
happens to be the name of the variable in the context where the macro is
expanded. Fix the macro to use the passed argument.
Fixes: 5dfd37c37a44 ("i40e: Split i40e_osdep.h")
Signed-off-by: Mohamed Khalfella <mkhalfella@purestorage.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Alexander Nowlin <alexander.nowlin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Several error return paths in ice_dpll_init_info() directly return
without freeing previously allocated resources, causing memory leaks:
- When de->input_prio allocation fails, d->inputs is leaked
- When dp->input_prio allocation fails, d->inputs and de->input_prio
are leaked
- When ice_get_cgu_rclk_pin_info() fails, all previously allocated
inputs/outputs/input_prio are leaked
- When ice_dpll_init_pins_info(RCLK_INPUT) fails, same resources
are leaked
Fix this by jumping to the deinit_info label which properly calls
ice_dpll_deinit_info() to free all allocated resources.
Fixes: d7999f5ea64b ("ice: implement dpll interface to control cgu")
Signed-off-by: ZhaoJinming <zhaojinming@uniontech.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
ice_dpll_deinit_info() calls kfree() on several pf->dplls fields
(inputs, outputs, eec.input_prio, pps.input_prio) but does not set
the pointers to NULL afterward. This leaves dangling pointers in the
pf->dplls structure.
While not currently exploitable through existing code paths, this is
unsafe because:
1. If ice_dpll_init_info() is called again after a deinit (e.g. during
driver recovery), and a subsequent allocation within init fails, the
error path will jump to deinit_info and call ice_dpll_deinit_info()
again. Since some pointers still hold the old freed addresses, this
would result in a double-free.
2. Any future code that checks these pointers before use or after free
would be unprotected against use-after-free.
Follow the common kernel convention of setting pointers to NULL after
kfree() so that:
- kfree(NULL) is a safe no-op, preventing double-free
- NULL checks on these pointers become meaningful
This is a preparatory fix for a subsequent patch that routes additional
error paths in ice_dpll_init_info() to the deinit_info label.
Fixes: d7999f5ea64b ("ice: implement dpll interface to control cgu")
Signed-off-by: ZhaoJinming <zhaojinming@uniontech.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
isl1208_setup_irq() calls enable_irq_wake() after a successful
IRQ request, but the driver has no remove path that balances it.
The driver is devm-only, so on unbind devm releases the IRQ -
but enable_irq_wake() is not undone by IRQ release, so the wake
count for that IRQ stays incremented.
Each rebind therefore leaks one wake reference; the leak doubles
for the chip variant that has a separate evdet IRQ, since
isl1208_setup_irq() is then called twice during probe.
Register a devm action that calls disable_irq_wake() per IRQ.
While at it, check enable_irq_wake()'s return value:
on failure, propagate the error rather than silently registering
a disable action for an IRQ whose wake state was never enabled.
Fixes: 9ece7cd833a3 ("rtc: isl1208: Add "evdet" interrupt source for isl1219")
Signed-off-by: John Madieu <john.madieu.xa@bp.renesas.com>
Link: https://patch.msgid.link/20260425154959.2796261-3-john.madieu.xa@bp.renesas.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
netif_keep_dst() only needs to be called once for the uplink VSI, not
once for each port representor. Move it from ice_eswitch_setup_repr()
to ice_eswitch_enable_switchdev().
Fixes: defd52455aee ("ice: do Tx through PF netdev in slow-path")
Signed-off-by: Marcin Szycik <marcin.szycik@intel.com>
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Patryk Holda <patryk.holda@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
ice_init_link() can return an error status from ice_update_link_info()
or ice_init_phy_user_cfg(), causing probe to fail.
An incorrect NVM update procedure can result in link/PHY errors, and
the recommended resolution is to update the NVM using the correct
procedure. If the driver fails probe due to link errors, the user
cannot update the NVM to recover. The link/PHY errors logged are
non-fatal: they are already annotated as 'not a fatal error if this
fails'.
Since none of the errors inside ice_init_link() should prevent probe
from completing, convert it to void and remove the error check in the
caller. All failures are already logged; callers have no meaningful
recovery path for link init errors.
Fixes: 5b246e533d01 ("ice: split probe into smaller functions")
Cc: stable@vger.kernel.org
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Alexander Nowlin <alexander.nowlin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Fix unreachable code: the conditionals in ice_set_pauseparam() used
the bitwise-AND operator suggesting aq_failures is a bitmap, but it
is actually an enum, making the third condition logically unreachable.
Replace the if-else ladder with a switch statement. Also move the
aq_failures initialization to the variable declaration and remove the
redundant zeroing from ice_set_fc().
Fixes: fcea6f3da546 ("ice: Add stats and ethtool support")
Signed-off-by: Lukasz Czapnik <lukasz.czapnik@intel.com>
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Resetting all VFs causes resource leak on VFs with FDIR filters
enabled as CTRL VSIs are only invalidated and not freed. Fix by using
ice_vf_ctrl_vsi_release() instead of ice_vf_ctrl_invalidate_vsi() which
aligns behavior with the ice_reset_vf() function.
Reproduction:
echo 1 > /sys/class/net/$pf/device/sriov_numvfs
ethtool -N $vf flow-type ether proto 0x9000 action 0
echo 1 > /sys/class/net/$pf/device/reset
Fixes: da62c5ff9dcd ("ice: Add support for per VF ctrl VSI enabling")
Signed-off-by: Dawid Osuchowski <dawid.osuchowski@linux.intel.com>
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
db_count controls how many doorbell slots are allocated and exposed. It is
also used by the doorbell mask helpers. After an EPC has been attached,
changing it from configfs can leave runtime paths using a different count
than the one used to set up the doorbell resources.
Reject db_count writes after EPC attach, and reject values outside
MIN_DB_COUNT..MAX_DB_COUNT before attach. Now that MIN_DB_COUNT documents
the usable doorbell floor, use it in the store path too.
While at it, apply the same after-attach guard to the other vNTB configfs
knobs. BAR choices, spad_count, memory-window counts and sizes, and the
virtual PCI IDs are also consumed during bind, so changing them later at
runtime is meaningless and unsafe.
Return -EOPNOTSUPP for after-attach writes. The value itself may be valid,
but changing it in that state is not supported.
Signed-off-by: Koichiro Den <den@valinux.co.jp>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260513024923.451765-6-den@valinux.co.jp
|
|
pci-epf-vntb reserves slot 0 for link events and keeps slot 1 unused for
legacy layout compatibility. A db_count smaller than MIN_DB_COUNT leaves
no usable doorbell slot after those reservations.
Reject such configurations when configuring interrupts.
While at it, move MAX_DB_COUNT next to MIN_DB_COUNT. They are used as a
pair in the range check, and keeping them together makes the valid doorbell
range easier to read.
Signed-off-by: Koichiro Den <den@valinux.co.jp>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260513024923.451765-5-den@valinux.co.jp
|
|
ntb_db_event() expects the vector number to be relative to the first
doorbell vector starting at 0.
pci-epf-vntb reserves vector 0 for link events and uses higher vector
indices for doorbells. By passing the raw slot index to ntb_db_event(),
it effectively assumes that doorbell 0 maps to vector 1.
However, because the host uses a legacy slot layout and writes doorbell
0 into the third slot, doorbell 0 ultimately appears as vector 2 from
the NTB core perspective.
Adjust pci-epf-vntb to:
- skip the unused second slot, and
- report doorbells as 0-based vectors (DB#0 -> vector 0).
This change does not introduce a behavioral difference until
.db_vector_count()/.db_vector_mask() are implemented, because without
those callbacks NTB clients effectively ignore the vector number.
Fixes: e35f56bb0330 ("PCI: endpoint: Support NTB transfer between RC and EP")
Signed-off-by: Koichiro Den <den@valinux.co.jp>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260513024923.451765-4-den@valinux.co.jp
|
|
The NTB .peer_db_set() callback may be invoked from atomic context.
pci-epf-vntb currently calls pci_epc_raise_irq() directly, but
pci_epc_raise_irq() may sleep (it takes epc->lock).
Avoid sleeping in atomic context by coalescing doorbell bits into an
atomic64 pending mask and raising MSIs from a work item. Limit the
amount of work per run to avoid monopolizing the workqueue under a
doorbell storm.
Clear stale pending bits before enabling the work item and after disabling
it during cleanup. Also mask requested doorbells against the currently
valid doorbell mask before queueing work, and iterate the pending u64 with
__ffs64() so high doorbell bits are handled correctly.
Fixes: e35f56bb0330 ("PCI: endpoint: Support NTB transfer between RC and EP")
Signed-off-by: Koichiro Den <den@valinux.co.jp>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260513024923.451765-3-den@valinux.co.jp
|
|
vntb_epf_peer_db_set() raises an MSI interrupt to notify the RC side of
a doorbell event. pci_epc_raise_irq(..., PCI_IRQ_MSI, interrupt_num)
takes a 1-based MSI interrupt number.
The ntb_hw_epf driver reserves MSI #1 for link events, so doorbells
would naturally start at MSI #2 (doorbell bit 0 -> MSI #2). However,
pci-epf-vntb has historically applied an extra offset and mapped doorbell
bit 0 to MSI #3. This matches the legacy behavior of ntb_hw_epf and has
been preserved since commit e35f56bb0330 ("PCI: endpoint: Support NTB
transfer between RC and EP").
This offset has not surfaced as a functional issue because:
- ntb_hw_epf typically allocates enough MSI vectors, so the off-by-one
still hits a valid MSI vector, and
- ntb_hw_epf does not implement .db_vector_count()/.db_vector_mask(), so
client drivers such as ntb_transport effectively ignore the vector
number and schedule all QPs.
Correcting the MSI number would break interoperability with peers
running older kernels.
Document the legacy offset to avoid confusion when enabling
per-db-vector handling.
Signed-off-by: Koichiro Den <den@valinux.co.jp>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260513024923.451765-2-den@valinux.co.jp
|
|
epf_ntb->db_count value should be within 1 to MAX_DB_COUNT. Current code
only checks for the upper bound, while the lower bound is unchecked. This
can cause a lot of issues in the driver if the user passes 'db_count' as 0.
Add a check for 0 also. While at it, remove the redundant 'db_count'
variable from epf_ntb_configure_interrupt().
Fixes: 8b821cf76150 ("PCI: endpoint: Add EP function driver to provide NTB functionality")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@oss.qualcomm.com>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/20260407124421.282766-3-mani@kernel.org
|
|
epf_ntb->db_count value should be within 1 to MAX_DB_COUNT. Current code
only checks for the upper bound, while the lower bound is unchecked. This
can cause a lot of issues in the driver if the user passes 'db_count' as 0.
Add a check for 0 also. While at it, remove the redundant 'db_count'
assignment.
Fixes: e35f56bb0330 ("PCI: endpoint: Support NTB transfer between RC and EP")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@oss.qualcomm.com>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Koichiro Den <den@valinux.co.jp>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260407124421.282766-2-mani@kernel.org
|
|
Driver core expects devices to be dynamically allocated and will, for
example, complain loudly when no release function has been provided.
Use root_device_register() to allocate and register the root device
instead of open coding using a static device.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
|
|
ntb_epf_vec_isr() calls pci_irq_vector() in hardirq context to derive
the vector number. pci_irq_vector() calls msi_get_virq() that takes a
mutex and can therefore trigger "scheduling while atomic" splats:
BUG: scheduling while atomic: kworker/u33:0/55/0x00010001
...
Call trace:
...
schedule+0x38/0x110
schedule_preempt_disabled+0x28/0x50
__mutex_lock.constprop.0+0x848/0x908
__mutex_lock_slowpath+0x18/0x30
mutex_lock+0x4c/0x60
msi_domain_get_virq+0xe8/0x138
pci_irq_vector+0x2c/0x60
ntb_epf_vec_isr+0x28/0x120 [ntb_hw_epf]
__handle_irq_event_percpu+0x70/0x3a8
handle_irq_event+0x48/0x100
handle_edge_irq+0x100/0x1c8
...
Cache the Linux IRQ number for vector 0 when vectors are allocated and
use it as a base in the ISR. Running the ISR in a threaded IRQ handler
would also avoid the problem, but that would be unnecessary here.
Fixes: 812ce2f8d14e ("NTB: Add support for EPF PCI Non-Transparent Bridge")
Signed-off-by: Koichiro Den <den@valinux.co.jp>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Cc: stable@vger.kernel.org # v5.12+
Link: https://patch.msgid.link/20260304083028.1391068-3-den@valinux.co.jp
|
|
ntb_epf_init_isr() requests multiple MSI/MSI-X vectors in a loop. If
request_irq() fails part-way through, it jumps straight to
pci_free_irq_vectors() without freeing already requested IRQs.
Fix the error path by freeing any successfully requested IRQs before
releasing the vectors.
Fixes: 812ce2f8d14e ("NTB: Add support for EPF PCI Non-Transparent Bridge")
Signed-off-by: Koichiro Den <den@valinux.co.jp>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Cc: stable@vger.kernel.org # v5.12+
Link: https://patch.msgid.link/20260304083028.1391068-2-den@valinux.co.jp
|
|
The assignment before the writel sequence is dead code (bar is
unconditionally overwritten by the re-read immediately after) so remove the
assignment entirely.
Note that the DB_BAR register is a plain value written by the endpoint
firmware; reading it carries no side effect.
Signed-off-by: Carlos Bilbao (Lambda) <carlos.bilbao@kernel.org>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Koichiro Den <den@valinux.co.jp>
Link: https://patch.msgid.link/20260410230300.135631-3-carlos.bilbao@kernel.org
|
|
pci_endpoint_test_doorbell() reads the BAR number directly from an endpoint
test register and uses it as an index into test->bar[]. Add a defensive
bounds check before the dereference: positive values >= PCI_STD_NUM_BARS
are out of range, and NO_BAR (-1) as a negative signed value would slip
past an upper-bound-only check.
Signed-off-by: Carlos Bilbao (Lambda) <carlos.bilbao@kernel.org>
[mani: changed errno to -ERANGE]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/20260410230300.135631-2-carlos.bilbao@kernel.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver updates from Greg KH:
"Here is the big set of staging driver updates for 7.2-rc1.
Nothing major in here, just constant grind of tiny cleanups and coding
style fixes and wrapper removals. Overall more code was removed than
added, always a nice sign that things are progressing forward.
Changes outside of drivers/staging/ was due to the octeon driver
changes, which for some reason also lives partially in the mips
subsystem, someday that all will be untangled and cleaned up, or just
removed entirely, it's hard to tell which is going to be its fate.
Other than octeon driver cleanups, in here are the usual:
- rtl8723bs driver reworking and cleanups, being the bulk of this
merge window given all of the issues and wrappers involved in that
beast of a driver
- most driver cleanups
- sm750fb driver cleanups (which might be done, as this really should
be moved to the drm layer one of these days...)
- other tiny staging driver cleanups and fixes
All of these have been in linux-next for many weeks with no reported
issues"
* tag 'staging-7.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (199 commits)
staging: most: video: avoid double free on video register failure
staging: sm750: rename CamelCase variable Bpp to bpp
staging: rtl8723bs: delete superfluous switch statement
staging: sm750fb: Mark g_noaccel, g_nomtrr and g_dualview as __ro_after_init
staging: rtl8723bs: propagate errno through hal xmit path
staging: rtl8723bs: propagate errno through xmit enqueue path
staging: rtl8723bs: convert rtw_xmit_classifier to return errno
staging: rtl8723bs: make rtw_xmit_classifier static
staging: rtl8723bs: simplify rtw_xmit_classifier control flow
staging: rtl8723bs: make _rtw_enqueue_cmd return 0 on success
staging: rtl8723bs: simplify rtw_enqueue_cmd control flow
staging: rtl8723bs: make _rtw_enqueue_cmd static
staging: rtl8723bs: simplify _rtw_enqueue_cmd control flow
staging: rtl8723bs: fix multiple blank lines in more hal/ files
staging: rtl8723bs: remove unused TXDESC_64_BYTES code
staging: rtl8723bs: remove unused DBG_XMIT_BUF and DBG_XMIT_BUF_EXT code
staging: rtl8723bs: fix multiple blank lines in hal/Hal* files
staging: rtl8723bs: fix multiple blank lines in hal/ files
staging: rtl8723bs: rtw_mlme: add blank line for readability
staging: rtl8723bs: rtw_mlme: wrap rtw_sitesurvey_cmd condition
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull misc driver updates from Greg KH:
"Here is the big set of char, misc, iio, fpga, and other small driver
subsystems changes for 7.2-rc1.
Lots of little stuff in here, the majority being of course the IIO
driver updates, as a list they are:
- IIO driver updates and additions
- GPIB driver bugfixes and cleanups
- Android binder driver updates (rust and C version)
- counter driver updates
- MHI driver updates
- mei driver updates
- w1 driver updates
- interconnect driver updates
- Comedi driver fixes and updates
- some obsolete char drivers removed (applicom and dtlk)
- hwtracing driver updates
- other tiny driver updates
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-7.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (406 commits)
w1: ds2482: Use named initializers for arrays of i2c_device_data
firmware: stratix10-svc: Add support to query Arm Trusted Firmware (ATF) version
firmware: stratix10-rsu: avoid blocking reboot_image sysfs when busy
coresight: ultrasoc-smb: Fix OOB write in smb_sync_perf_buffer()
iio: adc: nxp-sar-adc: harden buffer ISR against per-channel read failure
iio: chemical: scd30: Replace manual locking with RAII locking
iio: light: tsl2591: remove unneeded tsl2591_compatible_als_persist_cycle()
iio: dac: ad5686: create bus ops struct
iio: dac: ad5686: cleanup doc header of local structs
iio: dac: ad5686: add control_sync() for single-channel devices
iio: dac: ad5686: add helpers to handle powerdown masks
iio: dac: ad5686: add of_match table to the spi driver
iio: dac: ad5686: drop enum id
iio: dac: ad5686: remove redundant register definition
iio: dac: ad5686: refactor include headers
iio: adc: ad4080: fix AD4880 chip ID
iio: light: veml3328: add support for new device
dt-bindings: iio: light: veml6030: add veml3328
fpga: microchip-spi: fix zero header_size OOB read in mpf_ops_parse_header()
fpga: dfl-afu: validate DMA mapping length in afu_dma_map_region()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB and Thunderbolt driver updates from Greg KH:
"Here is the big set of USB and Thunderbolt driver changes for 7.2-rc1.
Lots of little stuff in here, major highlights include:
- USB4STREAM support for Thunderbolt devices. A new way to send "raw"
data very quickly over a USB4 connection to another system directly
- Other thunderbolt updates and changes to make the stream code work
- xhci driver updates and additions
- typec driver updates and additions
- usb gadget driver updates and fixes for reported issues
- zh_CN documentation translation of the USB documentation
- usb-serial driver updates
- dts cleanups for some USB platforms
- other minor USB driver updates and tweaks
All of these have been in linux-next for over a week with no reported
issues, most of them for many many weeks"
* tag 'usb-7.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (131 commits)
usb: ucsi: huawei_gaokun: support mode switching
thunderbolt: debugfs: Fix sideband write size check
thunderbolt: debugfs: Fix margining error counter buffer leak
usb: host: xhci-rcar: Split R-Car Gen2 and Gen3 .plat_start() handling
usb: host: xhci-rcar: Remove SET_XHCI_PLAT_PRIV_FOR_RCAR() macro
usb: xhci: allocate internal DCBAA mirror dynamically
usb: xhci: allocate DCBAA based on host controller max slots
usb: xhci: refactor DCBAA struct
xhci: Prevent queuing new commands if xhci is inaccessible
xhci: dbc: detect and recover hung DbC during enumeraton
xhci: dbc: add timestamps to DbC state changes in a new helper.
xhci: dbc: add helper to set and clear DbC DCE enable bit
xhci: dbc: serialize enabling and disabling dbc
xhci: dbc: Fix sysfs ABI Documentation for xhci dbc states
usb: xhci: Improve Soft Retries after short transfers
usb: xhci: Remove isochronous URB_SHORT_NOT_OK handling
usb: xhci: Remove skip_isoc_td()
usb: xhci: Simplify xhci_quiesce()
usb: xhci: remove legacy 'num_trbs_free' tracking
usb: xhci: fix typo in xhci_set_port_power() comment
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial driver updates from Greg KH:
"Here is the big set of TTY and Serial driver updates for 7.2-rc1.
Overall we end up removing more code than added, due to an obsolete
synclink_gt driver being removed from the tree, always a nice thing to
see happen.
Other than that driver removal, major things included in here are:
- max310x serial driver updates and fixes
- 8250 driver updates and rework in places to make it more "modern"
- dts file updates
- serial driver core tweaks and updates
- vt code cleanups
- vc_screen crash fixes
- other minor driver updates and cleanups
All of these have been in linux-next for well over a week with no
reported issues"
* tag 'tty-7.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (49 commits)
serial: 8250_pci: Don't specify conflicting values to pci_device_id members
vc_screen: fix null-ptr-deref in vcs_notifier() during concurrent vcs_write
serial: qcom_geni: Fix RX DMA stall when SE_DMA_RX_LEN_IN is zero
vt: merge ucs_is_zero_width()/ucs_is_double_width() into ucs_get_width()
serial: 8250: fix possible ISR soft lockup
dt-bindings: serial: rs485: remove deprecated .txt binding stub
serial: qcom-geni: trace: Add tracepoint support for Qualcomm GENI serial
tty: serial: Use named initializers for arrays of i2c_device_data
serial: 8250_dw: remove clock-notifier infrastructure
serial: 8250_dw: unregister 8250 port if clk_notifier_register() fails
amba/serial: amba-pl011: Bring back zx29 UART support
serial: 8250: Add support for console flow control
serial: 8250: Check LSR timeout on console flow control
serial: 8250: Set cons_flow on port registration
tty: serial: 8250: protect against NULL uart->port.dev in register
arm64: dts: add support for A9 based Amlogic BY401
dt-bindings: arm: amlogic: add A311Y3 support
serial: max310x: fix compile errors if CONFIG_SPI_MASTER is disabled
serial: qcom-geni: Avoid probing debug console UART without console support
serial: max310x: add comments for PLL limits
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/andi.shyti/linux
Pull more i2c updates from Andi Shyti:
"Cleanups:
- generic cleanups in qcom, qcom-cci and pxa, plus core cleanups in
algo-bit and atr
Fixes:
- davinci: clean up cpufreq notifier on probe failure
- imx-lpi2c: suspend the adapter while hardware is powered down
- ls2x-v2: return IRQ_HANDLED after servicing error interrupts
- stm32f7: fix timing calculation accuracy
DT bindings:
- microchip: permit resets
- i2c-mux-pinctrl: update maintainer entry
- i2c-mux-reg: convert bindings to DT schema"
* tag 'i2c-7.2-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/andi.shyti/linux:
i2c: pxa: Use named initializers for the platform_device_id array
i2c: imx-lpi2c: mark I2C adapter when hardware is powered down
i2c: stm32f7: truncate clock period instead of rounding it
dt-bindings: i2c: microchip,corei2c: permit resets
i2c: qcom: Unify user-visible "Qualcomm" name
i2c: ls2x-v2: return IRQ_HANDLED after servicing an error
i2c: atr: annotate i2c_atr_adap_desc->aliases with __counted_by_ptr
i2c: algo: bit: use str_plural helper in bit_xfer
dt-bindings: i2c: i2c-mux-pinctrl: change maintainer
dt-bindings: i2c: convert i2c-mux-reg to DT schema
i2c: davinci: Unregister cpufreq notifier on probe failure
i2c: qcom-cci: Remove overcautious disable_irq() calls
i2c: qcom-cci: Move cci_init() under cci_reset() function
i2c: qcom-cci: Do not check return value of cci_init()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux
Pull i3c updates from Alexandre Belloni:
"This cycle, there was a lot of work around the mipi-i3c-hci driver
that also led to improvements of the core. We also have support for a
new SoC, the Microchip SAMA7D65. And of course, there are small fixes
for the other controller drivers.
Subsystem:
- introduce dynamic address reconciliation after DAA
- add preliminary API for hub support
- fixes for dev_nack_retry_count handling
- move hot-join support in the core instead of open coding in
different drivers
Drivers:
- mipi-i3c-hci-pci: DMA abort, recovery and related improvements,
hot-join support, Microchip SAMA7D65 support, fix possible race in
IBI handling
- dw-i3c-master: fix IBI count register selection for versalnet
- svc: interrupt handling fixes for NPCM845"
* tag 'i3c/for-7.2' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux: (45 commits)
i3c: mipi-i3c-hci: Use named initializers for platform_device_id's .driver_data
i3c: master: Use unsigned int for dev_nack_retry_count consistently
i3c: master: Add missing runtime PM get in dev_nack_retry_count_store()
i3c: master: Update dev_nack_retry_count under maintenance lock
i3c: master: Expose the APIs to support I3C hub
i3c: master: rename i3c_master_reattach_i3c_dev() to *_locked
i3c: mipi-i3c-hci: add microchip sama7d65 SoC compatible with the required quirk
dt-bindings: i3c: mipi-i3c-hci: add Microchip SAMA7D65 compatible
i3c: Consistently define pci_device_ids using named initializers
i3c: master: Reconcile dynamic addresses after DAA
i3c: master: Move DAA API functions after i3c_master_add_i3c_dev_locked()
i3c: master: Make i3c_master_add_i3c_dev_locked() return void
i3c: mipi-i3c-hci: Tolerate i3c_master_add_i3c_dev_locked() failures in DAA
i3c: master: Prevent reuse of dynamic address on device add failure
i3c: mipi-i3c-hci: Ignore DISEC failures when disabling IBIs
i3c: mipi-i3c-hci: Fix race in i3c_hci_addr_to_dev()
i3c: mipi-i3c-hci: Add Hot-Join support
i3c: master: Export i3c_master_enec_disec_locked()
i3c: master: Defer new-device registration out of DAA caller context
i3c: dw: Drop redundant Hot-Join cancel_work_sync() in shutdown
...
|
|
The driver allocates domain generic chips using
irq_alloc_domain_generic_chips() during probe and sets up chained
handlers using irq_set_chained_handler_and_data(). However, on driver
removal, the generic chips are not freed and the chained handlers are
not removed.
The generic chips remain on the global gc_list and may later be accessed by
generic interrupt chip suspend, resume, or shutdown callbacks after the
driver has been removed, potentially resulting in a use-after-free and
kernel crash.
The chained handlers that were installed in probe for peripheral and
syswake interrupts are also left dangling, which can lead to spurious
interrupts accessing freed memory.
Fix these issues by:
- Setting IRQ_DOMAIN_FLAG_DESTROY_GC flag in domain->flags, so the
core code automatically removes generic chips when irq_domain_remove()
is called
- Clearing all chained handlers with NULL in pdc_intc_remove()
Fixes: b6ef9161e43a ("irq-imgpdc: add ImgTec PDC irqchip driver")
Signed-off-by: Qingshuang Fu <fuqingshuang@kylinos.cn>
Signed-off-by: Thomas Gleixner <tglx@kernel.org>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20260618021352.661773-1-fffsqian@163.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux
Pull hyperv updates from Wei Liu:
- Use wakeup mailbox to boot APs in Hyper-V VTL2 TDX guests (Yunhong
Jiang, Ricardo Neri)
- Move the Hyper-V IOMMU to its own subdirectory (Mukesh Rathor)
- Cosmetic changes to mshv and balloon driver (Junrui Luo, Markus
Elfring)
* tag 'hyperv-next-signed-20260621' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
mshv: add bounds check on vp_index in mshv_intercept_isr()
hv_balloon: Simplify data output in hv_balloon_debug_show()
x86/hyperv: Cosmetic changes in irqdomain.c for readability
iommu/hyperv: Create hyperv subdirectory under drivers/iommu
x86/hyperv/vtl: Use the wakeup mailbox to boot secondary CPUs
x86/hyperv/vtl: Mark the wakeup mailbox page as private
x86/acpi: Add a helper to get the address of the wakeup mailbox
x86/hyperv/vtl: Setup the 64-bit trampoline for TDX guests
x86/realmode: Make the location of the trampoline configurable
x86/hyperv/vtl: Set real_mode_header in hv_vtl_init_platform()
x86/dt: Parse the Wakeup Mailbox for Intel processors
dt-bindings: reserved-memory: Wakeup Mailbox for Intel processors
x86/acpi: Add functions to setup and access the wakeup mailbox
x86/topology: Add missing struct declaration and attribute dependency
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull more s390 updates from Alexander Gordeev:
- consolidate s390 idle time accounting by moving all CPU time tracking
to the architecture backend and eliminate the mix of architecture-
specific and common code accounting
- Add missing EXPORT_SYMBOL_GPL() to kcpustat_field_idle() and
kcpustat_field_iowait() functions
- Finalize ptep_get() conversion by replacing direct page table entry
dereferencing with proper accessors (ptep_get(), pmdp_get(), etc.)
- Explicitly check the buffer length in PKEY_VERIFYPROTK ioctl and
pkey_pckmo implementations and fail if the length is exceeded
* tag 's390-7.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/pkey: Check length in pkey_pckmo handler implementation
s390/pkey: Check length in PKEY_VERIFYPROTK ioctl
s390/idle: Add missing EXPORT_SYMBOL_GPL()
s390/mm: Complete ptep_get() conversion
s390/idle: Remove idle time and count sysfs files
s390/idle: Provide arch specific kcpustat_field_idle()/kcpustat_field_iowait()
s390/irq/idle: Use stcke instead of stckf for time stamps
s390/timex: Move union tod_clock type to separate header
|
|
Passing a maximum as 64-bit type to drm_sysfb_get_validated_int0()
can truncate the value to 32 bits. Use drm_sysfb_get_validated_size0(),
which uses 64-bit arithmetics. Then test the returned stride against
the limits of int to avoid truncations in the returned value. A valid
stride is in the range of [1, INT_MAX] inclusive.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reported-by: Sashiko <sashiko-bot@kernel.org>
Closes: https://lore.kernel.org/dri-devel/20260617114016.5A5991F000E9@smtp.kernel.org/
Fixes: 32ae90c66fb6 ("drm/sysfb: Add efidrm for EFI displays")
Fixes: a84eb6abe2b6 ("drm/sysfb: Add vesadrm for VESA displays")
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Javier Martinez Canillas <javierm@redhat.com>
Cc: dri-devel@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v6.16+
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patch.msgid.link/20260618084327.46567-5-tzimmermann@suse.de
|
|
Change the return type of drm_sysfb_get_visible_size() to s64 so
that it returns a possible errno code from _get_validated_size0().
Fix callers to handle the errno code.
The currently returned unsigned type converts an errno code to a
very large size value, which drivers interpret as visible size of
the system framebuffer. Later efforts to reserve the framebuffer
resource fail.
The bug has been present since efidrm and vesadrm got merged. It
was then part of each driver.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Fixes: 32ae90c66fb6 ("drm/sysfb: Add efidrm for EFI displays")
Fixes: a84eb6abe2b6 ("drm/sysfb: Add vesadrm for VESA displays")
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Javier Martinez Canillas <javierm@redhat.com>
Cc: dri-devel@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v6.16+
Link: https://patch.msgid.link/20260618084327.46567-4-tzimmermann@suse.de
|
|
Calculating the visible size of the system framebuffer can result in
truncation of the result. The calculation uses 32-bit arithmetics,
which can overflow if the values for height and stride are large. Fix
the issue by multiplying with mul_u32_u32().
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Fixes: 32ae90c66fb6 ("drm/sysfb: Add efidrm for EFI displays")
Fixes: a84eb6abe2b6 ("drm/sysfb: Add vesadrm for VESA displays")
Reported-by: Sashiko <sashiko-bot@kernel.org>
Closes: https://lore.kernel.org/dri-devel/20260617114027.1F2A71F000E9@smtp.kernel.org/
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Javier Martinez Canillas <javierm@redhat.com>
Cc: dri-devel@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v6.16+
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patch.msgid.link/20260618084327.46567-3-tzimmermann@suse.de
|
