| Age | Commit message (Collapse) | Author |
|---|
|
Correct 'metdata' -> 'metadata' in comment.
Signed-off-by: Haodong Tian <tianhd25@mails.tsinghua.edu.cn>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Message-ID: <20251112155916.3007639-1-tianhd25@mails.tsinghua.edu.cn>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
Move the comments just before we set EXT4_EXT_MAY_ZEROOUT in
ext4_split_convert_extents.
Signed-off-by: Yang Erkun <yangerkun@huawei.com>
Message-ID: <20251112084538.1658232-4-yangerkun@huawei.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
Retval from ext4_map_create_blocks means we really create some blocks,
cannot happened with m_flags without EXT4_MAP_UNWRITTEN and
EXT4_MAP_MAPPED.
Reviewed-by: Zhang Yi <yi.zhang@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Baokun Li <libaokun1@huawei.com>
Signed-off-by: Yang Erkun <yangerkun@huawei.com>
Message-ID: <20251112084538.1658232-3-yangerkun@huawei.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
This flag has been generalized to split an unwritten extent when we do
dio or dioread_nolock writeback, or to avoid merge new extents which was
created by extents split. Update some related comments too.
Reviewed-by: Zhang Yi <yi.zhang@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Baokun Li <libaokun1@huawei.com>
Signed-off-by: Yang Erkun <yangerkun@huawei.com>
Message-ID: <20251112084538.1658232-2-yangerkun@huawei.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
validation
When the MB_CHECK_ASSERT macro is enabled, we found that the
current validation logic in __mb_check_buddy has a gap in
detecting certain invalid buddy states, particularly related
to order-0 (bitmap) bits.
The original logic consists of three steps:
1. Validates higher-order buddies: if a higher-order bit is
set, at most one of the two corresponding lower-order bits
may be free; if a higher-order bit is clear, both lower-order
bits must be allocated (and their bitmap bits must be 0).
2. For any set bit in order-0, ensures all corresponding
higher-order bits are not free.
3. Verifies that all preallocated blocks (pa) in the group
have pa_pstart within bounds and their bitmap bits marked as
allocated.
However, this approach fails to properly validate cases where
order-0 bits are incorrectly cleared (0), allowing some invalid
configurations to pass:
corrupt integral
order 3 1 1
order 2 1 1 1 1
order 1 1 1 1 1 1 1 1 1
order 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Here we get two adjacent free blocks at order-0 with inconsistent
higher-order state, and the right one shows the correct scenario.
The root cause is insufficient validation of order-0 zero bits.
To fix this and improve completeness without significant performance
cost, we refine the logic:
1. Maintain the top-down higher-order validation, but we no longer
check the cases where the higher-order bit is 0, as this case will
be covered in step 2.
2. Enhance order-0 checking by examining pairs of bits:
- If either bit in a pair is set (1), all corresponding
higher-order bits must not be free.
- If both bits are clear (0), then exactly one of the
corresponding higher-order bits must be free
3. Keep the preallocation (pa) validation unchanged.
This change closes the validation gap, ensuring illegal buddy states
involving order-0 are correctly detected, while removing redundant
checks and maintaining efficiency.
Fixes: c9de560ded61f ("ext4: Add multi block allocator for ext4")
Suggested-by: Jan Kara <jack@suse.cz>
Signed-off-by: Yongjian Sun <sunyongjian1@huawei.com>
Reviewed-by: Baokun Li <libaokun1@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Message-ID: <20251106060614.631382-3-sunyongjian@huaweicloud.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
When the MB_CHECK_ASSERT macro is enabled, an assertion failure can
occur in __mb_check_buddy when checking preallocated blocks (pa) in
a block group:
Assertion failure in mb_free_blocks() : "groupnr == e4b->bd_group"
This happens when a pa at the very end of a block group (e.g.,
pa_pstart=32765, pa_len=3 in a group of 32768 blocks) becomes
exhausted - its pa_pstart is advanced by pa_len to 32768, which
lies in the next block group. If this exhausted pa (with pa_len == 0)
is still in the bb_prealloc_list during the buddy check, the assertion
incorrectly flags it as belonging to the wrong group. A possible
sequence is as follows:
ext4_mb_new_blocks
ext4_mb_release_context
pa->pa_pstart += EXT4_C2B(sbi, ac->ac_b_ex.fe_len)
pa->pa_len -= ac->ac_b_ex.fe_len
__mb_check_buddy
for each pa in group
ext4_get_group_no_and_offset
MB_CHECK_ASSERT(groupnr == e4b->bd_group)
To fix this, we modify the check to skip block group validation for
exhausted preallocations (where pa_len == 0). Such entries are in a
transitional state and will be removed from the list soon, so they
should not trigger an assertion. This change prevents the false
positive while maintaining the integrity of the checks for active
allocations.
Fixes: c9de560ded61f ("ext4: Add multi block allocator for ext4")
Signed-off-by: Yongjian Sun <sunyongjian1@huawei.com>
Reviewed-by: Baokun Li <libaokun1@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Message-ID: <20251106060614.631382-2-sunyongjian@huaweicloud.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@kernel.org
|
|
Fix a race between inline data destruction and block mapping.
The function ext4_destroy_inline_data_nolock() changes the inode data
layout by clearing EXT4_INODE_INLINE_DATA and setting EXT4_INODE_EXTENTS.
At the same time, another thread may execute ext4_map_blocks(), which
tests EXT4_INODE_EXTENTS to decide whether to call ext4_ext_map_blocks()
or ext4_ind_map_blocks().
Without i_data_sem protection, ext4_ind_map_blocks() may receive inode
with EXT4_INODE_EXTENTS flag and triggering assert.
kernel BUG at fs/ext4/indirect.c:546!
EXT4-fs (loop2): unmounting filesystem.
invalid opcode: 0000 [#1] PREEMPT SMP KASAN NOPTI
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.12.0-1 04/01/2014
RIP: 0010:ext4_ind_map_blocks.cold+0x2b/0x5a fs/ext4/indirect.c:546
Call Trace:
<TASK>
ext4_map_blocks+0xb9b/0x16f0 fs/ext4/inode.c:681
_ext4_get_block+0x242/0x590 fs/ext4/inode.c:822
ext4_block_write_begin+0x48b/0x12c0 fs/ext4/inode.c:1124
ext4_write_begin+0x598/0xef0 fs/ext4/inode.c:1255
ext4_da_write_begin+0x21e/0x9c0 fs/ext4/inode.c:3000
generic_perform_write+0x259/0x5d0 mm/filemap.c:3846
ext4_buffered_write_iter+0x15b/0x470 fs/ext4/file.c:285
ext4_file_write_iter+0x8e0/0x17f0 fs/ext4/file.c:679
call_write_iter include/linux/fs.h:2271 [inline]
do_iter_readv_writev+0x212/0x3c0 fs/read_write.c:735
do_iter_write+0x186/0x710 fs/read_write.c:861
vfs_iter_write+0x70/0xa0 fs/read_write.c:902
iter_file_splice_write+0x73b/0xc90 fs/splice.c:685
do_splice_from fs/splice.c:763 [inline]
direct_splice_actor+0x10f/0x170 fs/splice.c:950
splice_direct_to_actor+0x33a/0xa10 fs/splice.c:896
do_splice_direct+0x1a9/0x280 fs/splice.c:1002
do_sendfile+0xb13/0x12c0 fs/read_write.c:1255
__do_sys_sendfile64 fs/read_write.c:1323 [inline]
__se_sys_sendfile64 fs/read_write.c:1309 [inline]
__x64_sys_sendfile64+0x1cf/0x210 fs/read_write.c:1309
do_syscall_x64 arch/x86/entry/common.c:51 [inline]
do_syscall_64+0x35/0x80 arch/x86/entry/common.c:81
entry_SYSCALL_64_after_hwframe+0x6e/0xd8
Fixes: c755e251357a ("ext4: fix deadlock between inline_data and ext4_expand_extra_isize_ea()")
Cc: stable@vger.kernel.org # v4.11+
Signed-off-by: Alexey Nepomnyashih <sdl@nppct.ru>
Message-ID: <20251104093326.697381-1-sdl@nppct.ru>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
i_state_flags used on 32-bit archs, need to clear this flag when
alloc inode.
Find this issue when umount ext4, sometimes track the inode as orphan
accidently, cause ext4 mesg dump.
Fixes: acf943e9768e ("ext4: fix checks for orphan inodes")
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Baokun Li <libaokun1@huawei.com>
Reviewed-by: Zhang Yi <yi.zhang@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Message-ID: <20251104-ext4-v1-1-73691a0800f9@nxp.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@kernel.org
|
|
Copying the file system while it is mounted as read-only results in
a mount failure:
[~]# mkfs.ext4 -F /dev/sdc
[~]# mount /dev/sdc -o ro /mnt/test
[~]# dd if=/dev/sdc of=/dev/sda bs=1M
[~]# mount /dev/sda /mnt/test1
[ 1094.849826] JBD2: journal checksum error
[ 1094.850927] EXT4-fs (sda): Could not load journal inode
mount: mount /dev/sda on /mnt/test1 failed: Bad message
The process described above is just an abstracted way I came up with to
reproduce the issue. In the actual scenario, the file system was mounted
read-only and then copied while it was still mounted. It was found that
the mount operation failed. The user intended to verify the data or use
it as a backup, and this action was performed during a version upgrade.
Above issue may happen as follows:
ext4_fill_super
set_journal_csum_feature_set(sb)
if (ext4_has_metadata_csum(sb))
incompat = JBD2_FEATURE_INCOMPAT_CSUM_V3;
if (test_opt(sb, JOURNAL_CHECKSUM)
jbd2_journal_set_features(sbi->s_journal, compat, 0, incompat);
lock_buffer(journal->j_sb_buffer);
sb->s_feature_incompat |= cpu_to_be32(incompat);
//The data in the journal sb was modified, but the checksum was not
updated, so the data remaining in memory has a mismatch between the
data and the checksum.
unlock_buffer(journal->j_sb_buffer);
In this case, the journal sb copied over is in a state where the checksum
and data are inconsistent, so mounting fails.
To solve the above issue, update the checksum in memory after modifying
the journal sb.
Fixes: 4fd5ea43bc11 ("jbd2: checksum journal superblock")
Signed-off-by: Ye Bin <yebin10@huawei.com>
Reviewed-by: Baokun Li <libaokun1@huawei.com>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Reviewed-by: Jan Kara <jack@suse.cz>
Message-ID: <20251103010123.3753631-1-yebin@huaweicloud.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@kernel.org
|
|
params.mount_opts may come as potentially non-NUL-term string. Userspace
is expected to pass a NUL-term string. Add an extra check to ensure this
holds true. Note that further code utilizes strscpy_pad() so this is just
for proper informing the user of incorrect data being provided.
Found by Linux Verification Center (linuxtesting.org).
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Reviewed-by: Baokun Li <libaokun1@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Message-ID: <20251101160430.222297-2-pchelkin@ispras.ru>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@kernel.org
|
|
strscpy_pad() can't be used to copy a non-NUL-term string into a NUL-term
string of possibly bigger size. Commit 0efc5990bca5 ("string.h: Introduce
memtostr() and memtostr_pad()") provides additional information in that
regard. So if this happens, the following warning is observed:
strnlen: detected buffer overflow: 65 byte read of buffer size 64
WARNING: CPU: 0 PID: 28655 at lib/string_helpers.c:1032 __fortify_report+0x96/0xc0 lib/string_helpers.c:1032
Modules linked in:
CPU: 0 UID: 0 PID: 28655 Comm: syz-executor.3 Not tainted 6.12.54-syzkaller-00144-g5f0270f1ba00 #0
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-debian-1.16.3-2 04/01/2014
RIP: 0010:__fortify_report+0x96/0xc0 lib/string_helpers.c:1032
Call Trace:
<TASK>
__fortify_panic+0x1f/0x30 lib/string_helpers.c:1039
strnlen include/linux/fortify-string.h:235 [inline]
sized_strscpy include/linux/fortify-string.h:309 [inline]
parse_apply_sb_mount_options fs/ext4/super.c:2504 [inline]
__ext4_fill_super fs/ext4/super.c:5261 [inline]
ext4_fill_super+0x3c35/0xad00 fs/ext4/super.c:5706
get_tree_bdev_flags+0x387/0x620 fs/super.c:1636
vfs_get_tree+0x93/0x380 fs/super.c:1814
do_new_mount fs/namespace.c:3553 [inline]
path_mount+0x6ae/0x1f70 fs/namespace.c:3880
do_mount fs/namespace.c:3893 [inline]
__do_sys_mount fs/namespace.c:4103 [inline]
__se_sys_mount fs/namespace.c:4080 [inline]
__x64_sys_mount+0x280/0x300 fs/namespace.c:4080
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0x64/0x140 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x76/0x7e
Since userspace is expected to provide s_mount_opts field to be at most 63
characters long with the ending byte being NUL-term, use a 64-byte buffer
which matches the size of s_mount_opts, so that strscpy_pad() does its job
properly. Return with error if the user still managed to provide a
non-NUL-term string here.
Found by Linux Verification Center (linuxtesting.org) with Syzkaller.
Fixes: 8ecb790ea8c3 ("ext4: avoid potential buffer over-read in parse_apply_sb_mount_options()")
Cc: stable@vger.kernel.org
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Reviewed-by: Baokun Li <libaokun1@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Message-ID: <20251101160430.222297-1-pchelkin@ispras.ru>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
When jbd2_journal_abort() is called, the provided error code is stored
in the journal superblock. Some existing calls hard-code -EIO even when
the actual failure is not I/O related.
This patch updates those calls to pass more accurate error codes,
allowing the superblock to record the true cause of failure. This helps
improve diagnostics and debugging clarity when analyzing journal aborts.
Signed-off-by: Wengang Wang <wen.gang.wang@oracle.com>
Reviewed-by: Zhang Yi <yi.zhang@huawei.com>
Message-ID: <20251031210501.7337-1-wen.gang.wang@oracle.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
corrupted
There's issue when file system corrupted:
------------[ cut here ]------------
kernel BUG at fs/jbd2/transaction.c:1289!
Oops: invalid opcode: 0000 [#1] SMP KASAN PTI
CPU: 5 UID: 0 PID: 2031 Comm: mkdir Not tainted 6.18.0-rc1-next
RIP: 0010:jbd2_journal_get_create_access+0x3b6/0x4d0
RSP: 0018:ffff888117aafa30 EFLAGS: 00010202
RAX: 0000000000000000 RBX: ffff88811a86b000 RCX: ffffffff89a63534
RDX: 1ffff110200ec602 RSI: 0000000000000004 RDI: ffff888100763010
RBP: ffff888100763000 R08: 0000000000000001 R09: ffff888100763028
R10: 0000000000000003 R11: 0000000000000000 R12: 0000000000000000
R13: ffff88812c432000 R14: ffff88812c608000 R15: ffff888120bfc000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f91d6970c99 CR3: 00000001159c4000 CR4: 00000000000006f0
Call Trace:
<TASK>
__ext4_journal_get_create_access+0x42/0x170
ext4_getblk+0x319/0x6f0
ext4_bread+0x11/0x100
ext4_append+0x1e6/0x4a0
ext4_init_new_dir+0x145/0x1d0
ext4_mkdir+0x326/0x920
vfs_mkdir+0x45c/0x740
do_mkdirat+0x234/0x2f0
__x64_sys_mkdir+0xd6/0x120
do_syscall_64+0x5f/0xfa0
entry_SYSCALL_64_after_hwframe+0x76/0x7e
The above issue occurs with us in errors=continue mode when accompanied by
storage failures. There have been many inconsistencies in the file system
data.
In the case of file system data inconsistency, for example, if the block
bitmap of a referenced block is not set, it can lead to the situation where
a block being committed is allocated and used again. As a result, the
following condition will not be satisfied then trigger BUG_ON. Of course,
it is entirely possible to construct a problematic image that can trigger
this BUG_ON through specific operations. In fact, I have constructed such
an image and easily reproduced this issue.
Therefore, J_ASSERT() holds true only under ideal conditions, but it may
not necessarily be satisfied in exceptional scenarios. Using J_ASSERT()
directly in abnormal situations would cause the system to crash, which is
clearly not what we want. So here we directly trigger a JBD abort instead
of immediately invoking BUG_ON.
Fixes: 470decc613ab ("[PATCH] jbd2: initial copy of files from jbd")
Signed-off-by: Ye Bin <yebin10@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Message-ID: <20251025072657.307851-1-yebin@huaweicloud.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@kernel.org
|
|
There exists a memory leak of kernfs_iattrs contained as an element
of kernfs_node allocated in __kernfs_new_node(). __kernfs_setattr()
allocates kernfs_iattrs as a sub-object, and the LSM security check
incorrectly errors out and does not free the kernfs_iattrs sub-object.
Make an additional error out case that properly frees kernfs_iattrs if
security_kernfs_init_security() fails.
Fixes: e19dfdc83b60 ("kernfs: initialize security of newly created nodes")
Co-developed-by: Oliver Rosenberg <olrose55@gmail.com>
Signed-off-by: Oliver Rosenberg <olrose55@gmail.com>
Signed-off-by: Will Rosenberg <whrosenb@asu.edu>
Link: https://patch.msgid.link/20251125151332.2010687-1-whrosenb@asu.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
On an ARM64 A1 system, it's possible to have physical memory span
up to the 64T boundary, like below
$ lsmem -b -r -n -o range,size
0x0000000080000000-0x00000000bfffffff 1073741824
0x0000080000000000-0x000008007fffffff 2147483648
0x00000800c0000000-0x0000087fffffffff 546534588416
0x0000400000000000-0x00004000bfffffff 3221225472
0x0000400100000000-0x0000407fffffffff 545460846592
So it's time to extend /sys/kernel/mm/page_idle/bitmap to be able
to account for >2G number of pages, by raising the kernfs file size
limit.
Signed-off-by: Jane Chu <jane.chu@oracle.com>
Link: https://patch.msgid.link/20251111202606.1505437-1-jane.chu@oracle.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When constifying instances of struct attribute, for consistency the
corresponding .is_visible() callback should be adapted, too.
Introduce a temporary transition mechanism until all callbacks are
converted.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://patch.msgid.link/20251029-sysfs-const-attr-prep-v5-4-ea7d745acff4@weissschuh.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The primary consumer is link_path_walk(), calling walk_component() every
time which in turn calls step_into().
Inlining these saves overhead of 2 function calls per path component,
along with allowing the compiler to do better job optimizing them in place.
step_into() had absolutely atrocious assembly to facilitate the
slowpath. In order to lessen the burden at the callsite all the hard
work is moved into step_into_slowpath() and instead an inline-able
fastpath is implemented for rcu-walk.
The new fastpath is a stripped down step_into() RCU handling with a
d_managed() check from handle_mounts().
Benchmarked as follows on Sapphire Rapids:
1. the "before" was a kernel with not-yet-merged optimizations (notably
elision of calls to security_inode_permission() and marking ext4
inodes as not having acls as applicable)
2. "after" is the same + the prep patch + this patch
3. benchmark consists of issuing 205 calls to access(2) in a loop with
pathnames lifted out of gcc and the linker building real code, most
of which have several path components and 118 of which fail with
-ENOENT.
Result in terms of ops/s:
before: 21619
after: 22536 (+4%)
profile before:
20.25% [kernel] [k] __d_lookup_rcu
10.54% [kernel] [k] link_path_walk
10.22% [kernel] [k] entry_SYSCALL_64
6.50% libc.so.6 [.] __GI___access
6.35% [kernel] [k] strncpy_from_user
4.87% [kernel] [k] step_into
3.68% [kernel] [k] kmem_cache_alloc_noprof
2.88% [kernel] [k] walk_component
2.86% [kernel] [k] kmem_cache_free
2.14% [kernel] [k] set_root
2.08% [kernel] [k] lookup_fast
after:
23.38% [kernel] [k] __d_lookup_rcu
11.27% [kernel] [k] entry_SYSCALL_64
10.89% [kernel] [k] link_path_walk
7.00% libc.so.6 [.] __GI___access
6.88% [kernel] [k] strncpy_from_user
3.50% [kernel] [k] kmem_cache_alloc_noprof
2.01% [kernel] [k] kmem_cache_free
2.00% [kernel] [k] set_root
1.99% [kernel] [k] lookup_fast
1.81% [kernel] [k] do_syscall_64
1.69% [kernel] [k] entry_SYSCALL_64_safe_stack
While walk_component() and step_into() of course disappear from the
profile, the link_path_walk() barely gets more overhead despite the
inlining thanks to the fast path added and while completing more walks
per second.
I did not investigate why overhead grew a lot on __d_lookup_rcu().
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Link: https://patch.msgid.link/20251120003803.2979978-2-mjguzik@gmail.com
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
Symlink handling is already marked as unlikely and pushing out some of
it into pick_link() reduces register spillage on entry to step_into()
with gcc 14.2.
The compiler needed additional convincing that handle_mounts() is
unlikely to fail.
At the same time neither clang nor gcc could be convinced to tail-call
into pick_link().
While pick_link() takes an address of stack-based object as an argument
(which definitely prevents the optimization), splitting it into separate
<dentry, mount> tuple did not help. The issue persists even when
compiled without stack protector. As such nothing was done about this
for the time being to not grow the diff.
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Link: https://patch.msgid.link/20251120003803.2979978-1-mjguzik@gmail.com
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
Orangefs has no i_version handling and __orangefs_setattr already
explicitly marks the inode dirty. So instead of the using
the flags return value from generic_update_time, just call the
lower level inode_update_timestamps helper directly.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://patch.msgid.link/20251120064859.2911749-7-hch@lst.de
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
Since commit e41f941a2311 ("Btrfs: move over to use ->update_time") this
is not a copy of the high-level file_update_time helper.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://patch.msgid.link/20251120064859.2911749-6-hch@lst.de
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
Btrfs updates the device node timestamps for block device special files
when it stop using the device.
Commit 8f96a5bfa150 ("btrfs: update the bdev time directly when closing")
switch that update from the correct layering to directly call the
low-level helper on the bdev inode. This is wrong and got fixed in
commit 54fde91f52f5 ("btrfs: update device path inode time instead of
bd_inode") by updating the file system inode instead of the bdev inode,
but this kept the incorrect bypassing of the VFS interfaces and file
system ->update_times method. Fix this by using the propet vfs_utimes
interface.
Fixes: 8f96a5bfa150 ("btrfs: update the bdev time directly when closing")
Fixes: 54fde91f52f5 ("btrfs: update device path inode time instead of bd_inode")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://patch.msgid.link/20251120064859.2911749-5-hch@lst.de
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
This will be used to replace an incorrect direct call into
generic_update_time in btrfs.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://patch.msgid.link/20251120064859.2911749-4-hch@lst.de
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
FMODE_NOCMTIME used to be just a hack for the legacy XFS handle-based
"invisible I/O", but commit e5e9b24ab8fa ("nfsd: freeze c/mtime updates
with outstanding WRITE_ATTRS delegation") started using it from
generic callers.
I'm not sure other file systems are actually read for this in general,
so the above commit should get a closer look, but for it to make any
sense, file_update_time needs to respect the flag.
Lift the check from file_modified_flags to file_update_time so that
users of file_update_time inherit the behavior and so that all the
checks are done in one place.
Fixes: e5e9b24ab8fa ("nfsd: freeze c/mtime updates with outstanding WRITE_ATTRS delegation")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://patch.msgid.link/20251120064859.2911749-3-hch@lst.de
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
Currently the two high-level APIs use two helper functions to implement
almost all of the logic. Refactor the two helpers and the common logic
into a new file_update_time_flags routine that gets the iocb flags or
0 in case of file_update_time passed so that the entire logic is
contained in a single function and can be easily understood and modified.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://patch.msgid.link/20251120064859.2911749-2-hch@lst.de
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
After commit b77b4a4815a9 ("gfs2: Rework freeze / thaw logic"),
the freeze error handling is broken because gfs2_do_thaw()
overwrites the 'error' variable, causing incorrect processing
of the original freeze error.
Fix this by calling gfs2_do_thaw() when gfs2_lock_fs_check_clean()
fails but ignoring its return value to preserve the original
freeze error for proper reporting.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: b77b4a4815a9 ("gfs2: Rework freeze / thaw logic")
Cc: stable@vger.kernel.org # v6.5+
Signed-off-by: Alexey Velichayshiy <a.velichayshiy@ispras.ru>
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
|
|
Function new_inode() returns a new inode with inode->i_mapping->gfp_mask
set to GFP_HIGHUSER_MOVABLE. This value includes the __GFP_FS flag, so
allocations in that address space can recurse into filesystem memory
reclaim. We don't want that to happen because it can consume a
significant amount of stack memory.
Worse than that is that it can also deadlock: for example, in several
places, gfs2_unstuff_dinode() is called inside filesystem transactions.
This calls filemap_grab_folio(), which can allocate a new folio, which
can trigger memory reclaim. If memory reclaim recurses into the
filesystem and starts another transaction, a deadlock will ensue.
To fix these kinds of problems, prevent memory reclaim from recursing
into filesystem code by making sure that the gfp_mask of inode address
spaces doesn't include __GFP_FS.
The "meta" and resource group address spaces were already using GFP_NOFS
as their gfp_mask (which doesn't include __GFP_FS). The default value
of GFP_HIGHUSER_MOVABLE is less restrictive than GFP_NOFS, though. To
avoid being overly limiting, use the default value and only knock off
the __GFP_FS flag. I'm not sure if this will actually make a
difference, but it also shouldn't hurt.
This patch is loosely based on commit ad22c7a043c2 ("xfs: prevent stack
overflows from page cache allocation").
Fixes xfstest generic/273.
Fixes: dc0b9435238c ("gfs: Don't use GFP_NOFS in gfs2_unstuff_dinode")
Reviewed-by: Andrew Price <anprice@redhat.com>
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
|
|
The fuse_ilookup() function only sets *fm on the success path so this
"if (fm) {" NULL check doesn't work. The "fm" pointer is either
uninitialized or valid. Check the "inode" pointer instead.
Also, while it's not necessary, it is cleaner to move the iput(inode)
under the NULL check as well.
Fixes: 64becd224ff9 ("fuse: new work queue to invalidate dentries from old epochs")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Luis Henriques <luis@igalia.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
|
|
When a request is terminated before it has been committed, the request
is not removed from the queue's list. This leaves a dangling list entry
that leads to list corruption and use-after-free issues.
Remove the request from the queue's list for terminated non-committed
requests.
Signed-off-by: Joanne Koong <joannelkoong@gmail.com>
Fixes: c090c8abae4b ("fuse: Add io-uring sqe commit and fetch support")
Cc: stable@vger.kernel.org
Reviewed-by: Bernd Schubert <bschubert@ddn.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
|
|
KVM guest_memfd changes for 6.19:
- Add NUMA mempolicy support for guest_memfd, and clean up a variety of
rough edges in guest_memfd along the way.
- Define a CLASS to automatically handle get+put when grabbing a guest_memfd
from a memslot to make it harder to leak references.
- Enhance KVM selftests to make it easer to develop and debug selftests like
those added for guest_memfd NUMA support, e.g. where test and/or KVM bugs
often result in hard-to-debug SIGBUS errors.
- Misc cleanups.
|
|
Add a comment on regeneration to the generated files.
The comment is placed after the YNL-GEN line[1], as to not interfere
with ynl-regen.sh's detection logic.
[1] and after the optional YNL-ARG line.
Link: https://lore.kernel.org/r/aR5m174O7pklKrMR@zx2c4.com/
Suggested-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Acked-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20251120174429.390574-3-ast@fiberby.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When having a multiuser mount with domain= specified and using
cifscreds, cifs_set_cifscreds() will end up setting @ctx->domainname,
so it needs to be freed before leaving cifs_construct_tcon().
This fixes the following memory leak reported by kmemleak:
mount.cifs //srv/share /mnt -o domain=ZELDA,multiuser,...
su - testuser
cifscreds add -d ZELDA -u testuser
...
ls /mnt/1
...
umount /mnt
echo scan > /sys/kernel/debug/kmemleak
cat /sys/kernel/debug/kmemleak
unreferenced object 0xffff8881203c3f08 (size 8):
comm "ls", pid 5060, jiffies 4307222943
hex dump (first 8 bytes):
5a 45 4c 44 41 00 cc cc ZELDA...
backtrace (crc d109a8cf):
__kmalloc_node_track_caller_noprof+0x572/0x710
kstrdup+0x3a/0x70
cifs_sb_tlink+0x1209/0x1770 [cifs]
cifs_get_fattr+0xe1/0xf50 [cifs]
cifs_get_inode_info+0xb5/0x240 [cifs]
cifs_revalidate_dentry_attr+0x2d1/0x470 [cifs]
cifs_getattr+0x28e/0x450 [cifs]
vfs_getattr_nosec+0x126/0x180
vfs_statx+0xf6/0x220
do_statx+0xab/0x110
__x64_sys_statx+0xd5/0x130
do_syscall_64+0xbb/0x380
entry_SYSCALL_64_after_hwframe+0x77/0x7f
Fixes: f2aee329a68f ("cifs: set domainName when a domain-key is used in multiuser")
Signed-off-by: Paulo Alcantara (Red Hat) <pc@manguebit.org>
Reviewed-by: David Howells <dhowells@redhat.com>
Cc: Jay Shin <jaeshin@redhat.com>
Cc: stable@vger.kernel.org
Cc: linux-cifs@vger.kernel.org
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
Currently, HFS declares on-disk layout's metadata structures
in fs/hfs/hfs.h and HFS+ declares it in fs/hfsplus/hfsplus_raw.h.
However, HFS and HFS+ on-disk layouts have some similarity and
overlapping in declarations. As a result, fs/hfs/hfs.h and
fs/hfsplus/hfsplus_raw.h contain multiple duplicated declarations.
Moreover, both HFS and HFS+ drivers contain completely similar
implemented functionality in multiple places.
This patch is moving the on-disk layout declarations from
fs/hfs/hfs.h and fs/hfsplus/hfsplus_raw.h into
include/linux/hfs_common.h with the goal to exclude
the duplication in declarations. Also, this patch prepares
the basis for creating a hfslib that can aggregate common
functionality without necessity to duplicate the same code
in HFS and HFS+ drivers.
Signed-off-by: Viacheslav Dubeyko <slava@dubeyko.com>
cc: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
cc: Yangtao Li <frank.li@vivo.com>
cc: linux-fsdevel@vger.kernel.org
Signed-off-by: Viacheslav Dubeyko <slava@dubeyko.com>
|
|
The xfstests' test-case generic/101 leaves HFS+ volume
in corrupted state:
sudo ./check generic/101
FSTYP -- hfsplus
PLATFORM -- Linux/x86_64 hfsplus-testing-0001 6.17.0-rc1+ #4 SMP PREEMPT_DYNAMIC Wed Oct 1 15:02:44 PDT 2025
MKFS_OPTIONS -- /dev/loop51
MOUNT_OPTIONS -- /dev/loop51 /mnt/scratch
generic/101 _check_generic_filesystem: filesystem on /dev/loop51 is inconsistent
(see XFSTESTS-2/xfstests-dev/results//generic/101.full for details)
Ran: generic/101
Failures: generic/101
Failed 1 of 1 tests
sudo fsck.hfsplus -d /dev/loop51
** /dev/loop51
Using cacheBlockSize=32K cacheTotalBlock=1024 cacheSize=32768K.
Executing fsck_hfs (version 540.1-Linux).
** Checking non-journaled HFS Plus Volume.
The volume name is untitled
** Checking extents overflow file.
** Checking catalog file.
** Checking multi-linked files.
** Checking catalog hierarchy.
** Checking extended attributes file.
** Checking volume bitmap.
** Checking volume information.
Invalid volume free block count
(It should be 2614350 instead of 2614382)
Verify Status: VIStat = 0x8000, ABTStat = 0x0000 EBTStat = 0x0000
CBTStat = 0x0000 CatStat = 0x00000000
** Repairing volume.
** Rechecking volume.
** Checking non-journaled HFS Plus Volume.
The volume name is untitled
** Checking extents overflow file.
** Checking catalog file.
** Checking multi-linked files.
** Checking catalog hierarchy.
** Checking extended attributes file.
** Checking volume bitmap.
** Checking volume information.
** The volume untitled was repaired successfully.
This test executes such steps: "Test that if we truncate a file
to a smaller size, then truncate it to its original size or
a larger size, then fsyncing it and a power failure happens,
the file will have the range [first_truncate_size, last_size[ with
all bytes having a value of 0x00 if we read it the next time
the filesystem is mounted.".
HFS+ keeps volume's free block count in the superblock.
However, hfsplus_file_fsync() doesn't store superblock's
content. As a result, superblock contains not correct
value of free blocks if a power failure happens.
This patch adds functionality of saving superblock's
content during hfsplus_file_fsync() call.
sudo ./check generic/101
FSTYP -- hfsplus
PLATFORM -- Linux/x86_64 hfsplus-testing-0001 6.18.0-rc3+ #96 SMP PREEMPT_DYNAMIC Wed Nov 19 12:47:37 PST 2025
MKFS_OPTIONS -- /dev/loop51
MOUNT_OPTIONS -- /dev/loop51 /mnt/scratch
generic/101 32s ... 30s
Ran: generic/101
Passed all 1 tests
sudo fsck.hfsplus -d /dev/loop51
** /dev/loop51
Using cacheBlockSize=32K cacheTotalBlock=1024 cacheSize=32768K.
Executing fsck_hfs (version 540.1-Linux).
** Checking non-journaled HFS Plus Volume.
The volume name is untitled
** Checking extents overflow file.
** Checking catalog file.
** Checking multi-linked files.
** Checking catalog hierarchy.
** Checking extended attributes file.
** Checking volume bitmap.
** Checking volume information.
** The volume untitled appears to be OK.
Signed-off-by: Viacheslav Dubeyko <slava@dubeyko.com>
cc: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
cc: Yangtao Li <frank.li@vivo.com>
cc: linux-fsdevel@vger.kernel.org
Link: https://lore.kernel.org/r/20251119223219.1824434-1-slava@dubeyko.com
Signed-off-by: Viacheslav Dubeyko <slava@dubeyko.com>
|
|
Add trace point to print client IP address, net namespace number,
device name and status of SCSI pr_preempt command.
Signed-off-by: Dai Ngo <dai.ngo@oracle.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
|
|
The reservation type argument for the pr_preempt call should match the
one used in nfsd4_block_get_device_info_scsi.
Fixes: f99d4fbdae67 ("nfsd: add SCSI layout support")
Cc: stable@vger.kernel.org
Signed-off-by: Dai Ngo <dai.ngo@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
|
|
Previously, while trying to create a server instance, if no
listening sockets were present then default parameter udp
and tcp listeners were created. It's unclear what purpose
was of starting these listeners were and how this could have
been triggered by the userland setup. This patch proposed
to ensure the reverse that we never end in a situation where
no listener sockets are created and we are trying to create
nfsd threads.
The problem it solves is: when nfs.conf only has tcp=n (and
nothing else for the choice of transports), nfsdctl would
still start the server and create udp and tcp listeners.
Signed-off-by: Olga Kornievskaia <okorniev@redhat.com>
Reviewed-by: NeilBrown <neil@brown.name>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
|
|
For consistency with sb routines.
ext4 is the only consumer outside of evict(). Damage-controlling it is
outside of the scope of this cleanup.
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Link: https://patch.msgid.link/20251103230911.516866-1-mjguzik@gmail.com
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
1. inode_bit_waitqueue() was somehow placed between __inode_add_lru() and
inode_add_lru(). move it up
2. assert ->i_lock is held in __inode_add_lru instead of just claiming it is
needed
3. s/__inode_add_lru/__inode_lru_list_add/ for consistency with itself
(inode_lru_list_del()) and similar routines for sb and io list
management
4. push list presence check into inode_lru_list_del(), just like sb and
io list
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Link: https://patch.msgid.link/20251029131428.654761-2-mjguzik@gmail.com
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
In the inode hash code grab the state while ->i_lock is held. If found
to be set, synchronize the sleep once more with the lock held.
In the real world the flag is not set most of the time.
Apart from being simpler to reason about, it comes with a minor speed up
as now clearing the flag does not require the smp_mb() fence.
While here rename wait_on_inode() to wait_on_new_inode() to line it up
with __wait_on_freeing_inode().
Christian Brauner <brauner@kernel.org> says:
As per the discussion in [1] I folded in the diff sent in [2].
Link: https://lore.kernel.org/69238e4d.a70a0220.d98e3.006e.GAE@google.com [1]
Link: https://lore.kernel.org/c2kpawomkbvtahjm7y5mposbhckb7wxthi3iqy5yr22ggpucrm@ufvxwy233qxo [2]
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Link: https://patch.msgid.link/20251010221737.1403539-1-mjguzik@gmail.com
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
Since commit 222f2c7c6d14 ("iomap: always run error completions in user
context"), read error completions are deferred to s_dio_done_wq. This
means the workqueue also needs to be allocated for async reads.
Fixes: 222f2c7c6d14 ("iomap: always run error completions in user context")
Reported-by: syzbot+a2b9a4ed0d61b1efb3f5@syzkaller.appspotmail.com
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://patch.msgid.link/20251124140013.902853-1-hch@lst.de
Tested-by: syzbot+a2b9a4ed0d61b1efb3f5@syzkaller.appspotmail.com
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
There are some cases where when iomap_read_end() is called, the folio
may already have been marked uptodate. For example, if the iomap block
needed zeroing, then the folio may have been marked uptodate after the
zeroing.
iomap_read_end() should unlock the folio instead of calling
folio_end_read(), which is how these cases were handled prior to commit
f8eaf79406fe ("iomap: simplify ->read_folio_range() error handling for
reads"). Calling folio_end_read() on an uptodate folio leads to buggy
behavior where marking an already uptodate folio as uptodate will XOR it
to be marked nonuptodate.
Fixes: f8eaf79406fe ("iomap: simplify ->read_folio_range() error handling for reads")
Signed-off-by: Joanne Koong <joannelkoong@gmail.com>
Link: https://patch.msgid.link/20251118211111.1027272-2-joannelkoong@gmail.com
Tested-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reported-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
Replace IOMAP_DIO_INLINE_COMP with a flag to indicate that the
completion should be offloaded. This removes a tiny bit of boilerplate
code, but more importantly just makes the code easier to follow as this
new flag gets set most of the time and only cleared in one place, while
it was the inverse for the old version.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://patch.msgid.link/20251113170633.1453259-6-hch@lst.de
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
Completions for pure overwrites don't need to be deferred to a workqueue
as there is no work to be done, or at least no work that needs a user
context. Set the IOMAP_DIO_INLINE_COMP by default for writes like we
already do for reads, and the clear it for all the cases that actually
do need a user context for completions to update the inode size or
record updates to the logical to physical mapping.
I've audited all users of the ->end_io callback, and they only require
user context for I/O that involves unwritten extents, COW, size
extensions, or error handling and all those are still run from workqueue
context.
This restores the behavior of the old pre-iomap direct I/O code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://patch.msgid.link/20251113170633.1453259-5-hch@lst.de
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
The way how iomap_dio_can_use_fua and the caller is structured is
a bit confusing, as the main guarding condition is hidden in the
helper, and the secondary conditions are split between caller and
callee.
Refactor the code, so that iomap_dio_bio_iter itself tracks if a write
might need metadata updates based on the iomap type and flags, and
then have a condition based on that to use the FUA flag.
Note that this also moves the REQ_OP_WRITE assignment to the end of
the branch to improve readability a bit.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://patch.msgid.link/20251113170633.1453259-4-hch@lst.de
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
At least zonefs expects error completions to be able to sleep. Because
error completions aren't performance critical, just defer them to workqueue
context unconditionally.
Fixes: 8dcc1a9d90c1 ("fs: New zonefs file system")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://patch.msgid.link/20251113170633.1453259-3-hch@lst.de
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
This was added by commit 099ada2c8726 ("io_uring/rw: add write support
for IOCB_DIO_CALLER_COMP") and disabled a little later by commit
838b35bb6a89 ("io_uring/rw: disable IOCB_DIO_CALLER_COMP") because it
didn't work. Remove all the related code that sat unused for 2 years.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://patch.msgid.link/20251113170633.1453259-2-hch@lst.de
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
Use find_next_bit()/find_next_zero_bit() for iomap uptodate bitmap
scanning. This uses __ffs() internally and is more efficient for
finding the next uptodate or non-uptodate bit than iterating through the
the bitmap range testing every bit.
Signed-off-by: Joanne Koong <joannelkoong@gmail.com>
Link: https://patch.msgid.link/20251111193658.3495942-10-joannelkoong@gmail.com
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Suggested-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
Use find_next_bit()/find_next_zero_bit() for iomap dirty bitmap
scanning. This uses __ffs() internally and is more efficient for
finding the next dirty or clean bit than iterating through the bitmap
range testing every bit.
Signed-off-by: Joanne Koong <joannelkoong@gmail.com>
Link: https://patch.msgid.link/20251111193658.3495942-9-joannelkoong@gmail.com
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Suggested-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
Trivial fix.
Signed-off-by: Askar Safin <safinaskar@gmail.com>
Link: https://patch.msgid.link/20251120211316.706725-1-safinaskar@gmail.com
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
Otherwise it gets inlined notably in walk_component(), which convinces
the compiler to push/pop additional registers in the fast path to
accomodate existence of the inlined version.
Shortens the fast path of that routine from 87 to 71 bytes.
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Link: https://patch.msgid.link/20251119144930.2911698-1-mjguzik@gmail.com
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
