| Age | Commit message (Collapse) | Author |
|---|
|
This reverts commit 7b7f2dd913829e06705035dfc41ca25fa6ec68d3.
There was some problems with an earlier cdns3 change, so this one needs
to be backed out as well.
Cc: Pawel Laszczak <pawell@cadence.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Reported-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/ac+LEWMCQpLSnfoD@nchen-desktop
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mani/mhi into char-misc-next
Manivannan writes:
MHI Host
--------
- Add support for Qualcomm SDX35 and Telit FE912C04 modems reusing the existing
channel and event configurations.
- Enable IP_SW and IP_ETH MHI channels for Qualcomm 5G DU X100 Accelerator
device (QDU100). These channels are used to carry O-RAN specific M-Plane,
S-Plane and Netconf packets. The drivers making use of these channels is being
reviewed.
- Add NMEA channels to Telit FN920C04 and FN990A modems for GPS/GNSS support
- Switch to mhi_async_power_up() API in pci_generic driver to avoid boot delays
as some Qcom modems take a while start. This API ensures that the pci_generic
driver powers up the modem asynchronously and doesn't block the system boot.
- Add pm_runtime_forbid() in remove callback to balance the pm_runtime_allow()
call made during the Mission Mode transition.
- Used kzalloc_flex() to simplify kzalloc() + kzalloc() calls
MHI Endpoint
------------
- Test for non-zero return value 'if (ret)' in the endpoint stack where
applicable to maintain code uniformity.
* tag 'mhi-for-v7.1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mani/mhi:
bus: mhi: host: pci_generic: Add Telit FE912C04 modem support
bus: mhi: ep: Test for non-zero return value where applicable
bus: mhi: host: Use kzalloc_flex
bus: mhi: host: pci_generic: Add pm_runtime_forbid() in remove callback
bus: mhi: host: pci_generic: Switch to async power up to avoid boot delays
bus: mhi: host: pci_generic: Add NMEA channels to FN920C04 and FN990A
bus: mhi: host: pci_generic: Enable IP_SW and IP_ETH channels for Qcom QDU100 device
bus: mhi: host: pci_generic: Add Qualcomm SDX35 modem
|
|
https://gitlab.freedesktop.org/drm/msm into drm-next
Changes for v7.1
CI:
- Uprev mesa
- Restore CI jobs for Qualcomm APQ8016 and APQ8096 devices
Core:
- Switched to of_get_available_child_by_name()
DPU:
- Fixes for DSC panels
- Fixed brownout because of the frequency / OPP mismatch
- Quad pipe preparation (not enabled yet)
- Switched to virtual planes by default
- Dropped VBIF_NRT support
- Added support for Eliza platform
- Reworked alpha handling
- Switched to correct CWB definitions on Eliza
- Dropped dummy INTF_0 on MSM8953
- Corrected INTFs related to DP-MST
DP:
- Removed debug prints looking into PHY internals
DSI:
- Fixes for DSC panels
- RGB101010 support
- Support for SC8280XP
- Moved PHY bindings from display/ to phy/
GPU:
- Preemption support for x2-85 and a840
- IFPC support for a840
- SKU detection support for x2-85 and a840
- Expose AQE support (VK ray-pipeline)
- Avoid locking in VM_BIND fence signaling path
- Fix to avoid reclaim in GPU snapshot path
- Disallow foreign mapping of _NO_SHARE BOs
- Couple a6xx gpu snapshot fixes
- Various other fixes
HDMI:
- Fixed infoframes programming
MDP5:
- Dropped support for MSM8974v1
- Dropped now unused code for MSM8974 v1 and SDM660 / MSM8998
Also misc small fixes
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <rob.clark@oss.qualcomm.com>
Link: https://patch.msgid.link/CACSVV012vn73BaUfk=Hw4WkQHZNPHiqfifWEunAqMc2EGOWUEQ@mail.gmail.com
|
|
CONFIG_CRASH_DM_CRYPT
This will prevent a compilation failure when CONFIG_CRASH_DUMP is enabled
but CONFIG_CRASH_DM_CRYPT is disabled,
arch/powerpc/kexec/elf_64.c: In function 'elf64_load':
>> arch/powerpc/kexec/elf_64.c:82:23: error: implicit declaration of function 'crash_load_dm_crypt_keys' [-Werror=implicit-function-declaration]
82 | ret = crash_load_dm_crypt_keys(image);
| ^~~~~~~~~~~~~~~~~~~~~~~~
cc1: some warnings being treated as errors
Link: https://lkml.kernel.org/r/20260225060347.718905-3-coxu@redhat.com
Signed-off-by: Coiby Xu <coxu@redhat.com>
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202602120648.RgQALnnI-lkp@intel.com/
Acked-by: Baoquan He <bhe@redhat.com>
Cc: Arnaud Lefebvre <arnaud.lefebvre@clever-cloud.com>
Cc: Christophe Leroy (CS GROUP) <chleroy@kernel.org>
Cc: Dave Young <dyoung@redhat.com>
Cc: Kairui Song <ryncsn@gmail.com>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Pingfan Liu <kernelfans@gmail.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Sourabh Jain <sourabhjain@linux.ibm.com>
Cc: Thomas Staudt <tstaudt@de.ibm.com>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Currently the high-level xor code chunks up all operations into small
units for only up to 1 + 4 vectors, and passes it to four different
methods. This means the FPU/vector context is entered and left a lot for
wide stripes, and a lot of indirect expensive indirect calls are
performed. Switch to passing the entire gen_xor request to the low-level
ops, and provide a macro to dispatch it to the existing helper.
This reduce the number of indirect calls and FPU/vector context switches
by a factor approaching nr_stripes / 4, and also reduces source and binary
code size.
Link: https://lkml.kernel.org/r/20260327061704.3707577-27-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Eric Biggers <ebiggers@kernel.org>
Tested-by: Eric Biggers <ebiggers@kernel.org>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Alexander Gordeev <agordeev@linux.ibm.com>
Cc: Alexandre Ghiti <alex@ghiti.fr>
Cc: Andreas Larsson <andreas@gaisler.com>
Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: "Borislav Petkov (AMD)" <bp@alien8.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Mason <clm@fb.com>
Cc: Christian Borntraeger <borntraeger@linux.ibm.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: David Sterba <dsterba@suse.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Huacai Chen <chenhuacai@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jason A. Donenfeld <jason@zx2c4.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Li Nan <linan122@huawei.com>
Cc: Madhavan Srinivasan <maddy@linux.ibm.com>
Cc: Magnus Lindholm <linmag7@gmail.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Richard Henderson <richard.henderson@linaro.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Song Liu <song@kernel.org>
Cc: Sven Schnelle <svens@linux.ibm.com>
Cc: Ted Ts'o <tytso@mit.edu>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: WANG Xuerui <kernel@xen0n.name>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
xor_blocks is very annoying to use, because it is limited to 4 + 1 sources
/ destinations, has an odd argument order and is completely undocumented.
Lift the code that loops around it from btrfs and async_tx/async_xor into
common code under the name xor_gen and properly document it.
[hch@lst.de: make xor_blocks less annoying to use]
Link: https://lkml.kernel.org/r/20260327061704.3707577-24-hch@lst.de
Link: https://lkml.kernel.org/r/20260327061704.3707577-23-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Eric Biggers <ebiggers@kernel.org>
Tested-by: Eric Biggers <ebiggers@kernel.org>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Alexander Gordeev <agordeev@linux.ibm.com>
Cc: Alexandre Ghiti <alex@ghiti.fr>
Cc: Andreas Larsson <andreas@gaisler.com>
Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: "Borislav Petkov (AMD)" <bp@alien8.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Mason <clm@fb.com>
Cc: Christian Borntraeger <borntraeger@linux.ibm.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: David Sterba <dsterba@suse.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Huacai Chen <chenhuacai@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jason A. Donenfeld <jason@zx2c4.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Li Nan <linan122@huawei.com>
Cc: Madhavan Srinivasan <maddy@linux.ibm.com>
Cc: Magnus Lindholm <linmag7@gmail.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Richard Henderson <richard.henderson@linaro.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Song Liu <song@kernel.org>
Cc: Sven Schnelle <svens@linux.ibm.com>
Cc: Ted Ts'o <tytso@mit.edu>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: WANG Xuerui <kernel@xen0n.name>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Move the asm/xor.h headers to lib/raid/xor/$(SRCARCH)/xor_arch.h and
include/linux/raid/xor_impl.h to lib/raid/xor/xor_impl.h so that the
xor.ko module implementation is self-contained in lib/raid/.
As this remove the asm-generic mechanism a new kconfig symbol is added to
indicate that a architecture-specific implementations exists, and
xor_arch.h should be included.
Link: https://lkml.kernel.org/r/20260327061704.3707577-22-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Eric Biggers <ebiggers@kernel.org>
Tested-by: Eric Biggers <ebiggers@kernel.org>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Alexander Gordeev <agordeev@linux.ibm.com>
Cc: Alexandre Ghiti <alex@ghiti.fr>
Cc: Andreas Larsson <andreas@gaisler.com>
Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: "Borislav Petkov (AMD)" <bp@alien8.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Mason <clm@fb.com>
Cc: Christian Borntraeger <borntraeger@linux.ibm.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: David Sterba <dsterba@suse.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Huacai Chen <chenhuacai@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jason A. Donenfeld <jason@zx2c4.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Li Nan <linan122@huawei.com>
Cc: Madhavan Srinivasan <maddy@linux.ibm.com>
Cc: Magnus Lindholm <linmag7@gmail.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Richard Henderson <richard.henderson@linaro.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Song Liu <song@kernel.org>
Cc: Sven Schnelle <svens@linux.ibm.com>
Cc: Ted Ts'o <tytso@mit.edu>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: WANG Xuerui <kernel@xen0n.name>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Move the generic implementations from asm-generic/xor.h to
per-implementaion .c files in lib/raid. This will build them
unconditionally even when an architecture forces a specific
implementation, but as we'll need at least one generic version for the
static_call optimization later on we'll pay that price.
Note that this would cause the second xor_block_8regs instance created by
arch/arm/lib/xor-neon.c to be generated instead of discarded as dead code,
so add a NO_TEMPLATE symbol to disable it for this case.
Link: https://lkml.kernel.org/r/20260327061704.3707577-11-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Eric Biggers <ebiggers@kernel.org>
Tested-by: Eric Biggers <ebiggers@kernel.org>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Alexander Gordeev <agordeev@linux.ibm.com>
Cc: Alexandre Ghiti <alex@ghiti.fr>
Cc: Andreas Larsson <andreas@gaisler.com>
Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: "Borislav Petkov (AMD)" <bp@alien8.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Mason <clm@fb.com>
Cc: Christian Borntraeger <borntraeger@linux.ibm.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: David Sterba <dsterba@suse.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Huacai Chen <chenhuacai@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jason A. Donenfeld <jason@zx2c4.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Li Nan <linan122@huawei.com>
Cc: Madhavan Srinivasan <maddy@linux.ibm.com>
Cc: Magnus Lindholm <linmag7@gmail.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Richard Henderson <richard.henderson@linaro.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Song Liu <song@kernel.org>
Cc: Sven Schnelle <svens@linux.ibm.com>
Cc: Ted Ts'o <tytso@mit.edu>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: WANG Xuerui <kernel@xen0n.name>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Drop the pretty confusing historic XOR_TRY_TEMPLATES and
XOR_SELECT_TEMPLATE, and instead let the architectures provide a
arch_xor_init that calls either xor_register to register candidates or
xor_force to force a specific implementation.
Link: https://lkml.kernel.org/r/20260327061704.3707577-10-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Eric Biggers <ebiggers@kernel.org>
Tested-by: Eric Biggers <ebiggers@kernel.org>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Alexander Gordeev <agordeev@linux.ibm.com>
Cc: Alexandre Ghiti <alex@ghiti.fr>
Cc: Andreas Larsson <andreas@gaisler.com>
Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: "Borislav Petkov (AMD)" <bp@alien8.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Mason <clm@fb.com>
Cc: Christian Borntraeger <borntraeger@linux.ibm.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: David Sterba <dsterba@suse.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Huacai Chen <chenhuacai@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jason A. Donenfeld <jason@zx2c4.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Li Nan <linan122@huawei.com>
Cc: Madhavan Srinivasan <maddy@linux.ibm.com>
Cc: Magnus Lindholm <linmag7@gmail.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Richard Henderson <richard.henderson@linaro.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Song Liu <song@kernel.org>
Cc: Sven Schnelle <svens@linux.ibm.com>
Cc: Ted Ts'o <tytso@mit.edu>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: WANG Xuerui <kernel@xen0n.name>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Keep xor.h for the public API, and split the struct xor_block_template
definition that is only needed by the xor.ko core and
architecture-specific optimizations into a separate xor_impl.h header.
Link: https://lkml.kernel.org/r/20260327061704.3707577-9-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Eric Biggers <ebiggers@kernel.org>
Tested-by: Eric Biggers <ebiggers@kernel.org>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Alexander Gordeev <agordeev@linux.ibm.com>
Cc: Alexandre Ghiti <alex@ghiti.fr>
Cc: Andreas Larsson <andreas@gaisler.com>
Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: "Borislav Petkov (AMD)" <bp@alien8.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Mason <clm@fb.com>
Cc: Christian Borntraeger <borntraeger@linux.ibm.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: David Sterba <dsterba@suse.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Huacai Chen <chenhuacai@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jason A. Donenfeld <jason@zx2c4.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Li Nan <linan122@huawei.com>
Cc: Madhavan Srinivasan <maddy@linux.ibm.com>
Cc: Magnus Lindholm <linmag7@gmail.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Richard Henderson <richard.henderson@linaro.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Song Liu <song@kernel.org>
Cc: Sven Schnelle <svens@linux.ibm.com>
Cc: Ted Ts'o <tytso@mit.edu>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: WANG Xuerui <kernel@xen0n.name>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Pull bpf fixes from Alexei Starovoitov:
- Fix register equivalence for pointers to packet (Alexei Starovoitov)
- Fix incorrect pruning due to atomic fetch precision tracking (Daniel
Borkmann)
- Fix grace period wait for bpf_link-ed tracepoints (Kumar Kartikeya
Dwivedi)
- Fix use-after-free of sockmap's sk->sk_socket (Kuniyuki Iwashima)
- Reject direct access to nullable PTR_TO_BUF pointers (Qi Tang)
- Reject sleepable kprobe_multi programs at attach time (Varun R
Mallya)
* tag 'bpf-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
selftests/bpf: Add more precision tracking tests for atomics
bpf: Fix incorrect pruning due to atomic fetch precision tracking
bpf: Reject sleepable kprobe_multi programs at attach time
bpf: reject direct access to nullable PTR_TO_BUF pointers
bpf: sockmap: Fix use-after-free of sk->sk_socket in sk_psock_verdict_data_ready().
bpf: Fix grace period wait for tracepoint bpf_link
bpf: Fix regsafe() for pointers to packet
|
|
In a subsequent patch, the regs_refine_cond_op and reg_bounds_sync
functions will be called in is_branch_taken instead of reg_set_min_max,
to simulate each branch's outcome. Since they will run before we branch
out, these two functions will need to work on temporary registers for
the two branches.
This refactoring patch prepares for that change, by introducing the
temporary registers on bpf_verifier_env and using them in
reg_set_min_max.
This change also allows us to save one fake_reg slot as we don't need to
allocate an additional temporary buffer in case of a BPF_K condition.
Finally, you may notice that this patch removes the check for
"false_reg1 == false_reg2" in reg_set_min_max. That check was introduced
in commit d43ad9da8052 ("bpf: Skip bounds adjustment for conditional
jumps on same scalar register") to avoid an invariant violation. Given
that "env->false_reg1 == env->false_reg2" doesn't make sense and
invariant violations are addressed in a subsequent commit, this patch
just removes the check.
Suggested-by: Eduard Zingerman <eddyz87@gmail.com>
Co-developed-by: Harishankar Vishwanathan <harishankar.vishwanathan@gmail.com>
Signed-off-by: Harishankar Vishwanathan <harishankar.vishwanathan@gmail.com>
Signed-off-by: Paul Chaignon <paul.chaignon@gmail.com>
Acked-by: Shung-Hsi Yu <shung-hsi.yu@suse.com>
Acked-by: Mykyta Yatsenko <yatsenko@meta.com>
Acked-by: Eduard Zingerman <eddyz87@gmail.com>
Link: https://lore.kernel.org/r/260b0270052944a420e1c56e6a92df4d43cadf03.1775142354.git.paul.chaignon@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Implement the standard ETHTOOL_PHY_DOWNSHIFT tunable for the LAN88xx
PHY. This allows runtime configuration of the auto-downshift feature
via ethtool:
ethtool --set-phy-tunable eth0 downshift on count 3
The LAN88xx PHY supports downshifting from 1000BASE-T to 100BASE-TX
after 2-5 failed auto-negotiation attempts. Valid count values are
2, 3, 4 and 5.
This is based on an earlier downstream implementation by Phil Elwell.
Signed-off-by: Nicolai Buchwitz <nb@tipi-net.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/20260401123848.696766-2-nb@tipi-net.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
"stdrng" is needed only in "FIPS mode". Therefore, make
crypto_stdrng_get_bytes() delegate to either the normal Linux RNG or to
"stdrng", depending on the current mode.
This will eliminate the need to built the SP800-90A DRBG and its
dependencies into CRYPTO_FIPS=n kernels.
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Now that crypto_default_rng, crypto_get_default_rng(), and
crypto_put_default_rng() have no users outside crypto/rng.c itself,
unexport them and make them static.
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
All callers of crypto_get_default_rng() use the following sequence:
crypto_get_default_rng()
crypto_rng_get_bytes(crypto_default_rng, ...)
crypto_put_default_rng()
While it may have been intended that callers amortize the cost of
getting and putting the "default RNG" (i.e. "stdrng") over multiple
calls, in practice that optimization is never used. The callers just
want a function that gets random bytes from the "stdrng".
Therefore, add such a function: crypto_stdrng_get_bytes().
Importantly, this decouples the callers from the crypto_rng API. That
allows a later commit to make this function simply call
get_random_bytes_wait() unless the kernel is in "FIPS mode".
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto fixes from Herbert Xu:
- Add missing async markers to tegra
- Fix long hmac key DMA handling in caam
- Fix spurious ENOSPC errors in deflate
- Fix SG chaining in af_alg
- Do not use in-place process in algif_aead
- Fix out-of-place destination overflow in authencesn
* tag 'v7.0-p4' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: authencesn - Do not place hiseq at end of dst for out-of-place decryption
crypto: algif_aead - Revert to operating out-of-place
crypto: af-alg - fix NULL pointer dereference in scatterwalk
crypto: deflate - fix spurious -ENOSPC
crypto: caam - fix overflow on long hmac keys
crypto: caam - fix DMA corruption on long hmac keys
crypto: tegra - Add missing CRYPTO_ALG_ASYNC
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into soc/dt
Qualcomm Arm64 DeviceTree updates for v7.1
Introduce the Eliza, Glymur, Mahua, and IPQ5210 Qualcomm SoCs.
Introduce the Redmi 4A, Redmi Go, Arduino Monza (VENTUNO Q), Redmi Note
8T, Purwa EVK, ECS Liva QCS710, additional variants of the DB820c,
Ayaneo Pocket S2, Thundercomm AI Mini PC G1, Samsung Galaxy Core Prime
LTE Verizon Wireless, Wiko Pulp 4G, the Purwa-variant of ASUS Vivobook
S15, the Eliza MTP, and the Glymur and Mahua CRDs.
Introduce UFS support and flatten the DWC3 node on Hamoa. Enable UFS,
SDC, DisplayPort audio playback, and an EL2 overlay for the Hamoa IoT
EVK. Enable DisplayPort audio on the Hamoa CRD and add HDMI support on
the ASUS Zenbook A14. Reduce the duplication of thermal sensors across
Purwa and Hamoa.
Add the QPIC SPI NAND controller on IPQ5332 and IPQ9574. Describe and
enable the eMMC controller on IPQ9574.
Add display, audio/compute remoteprocs, QUP devices, thermal sensors,
display, and CoreSight on the Kaanapali platform. Enable audio, compute
display, PMIC, Bluetooth, and WiFi on the MTP. Describe PMIC, audio and
compute remoteprocs on QRD.
Add role-switching support for the tertiary USB controller on Lemans.
Enable the tertiary USB controller and the GPIO expander on the Lemans
EVK, and add an overlay for the IFP Mezzanine.
Add UFS, camera control interface, audio GPR, and FastRPC support on
Milos. Enable UFS, camera EEPROMs, and hall effect sensor on the
Fairphone FP6.
Add camera control interface and fix a variety of things on the Monaco
platform, add missing FastRPC compute banks. Add eMMC support, describe
the DisplayPort bridge and GPIO expander on the Monaco EVK. Add overlay
for EVK camera and the IFP mezzanine.
Add touchscreen to the Xiaomi Redmi 4A, 5A, and Go, and fix the board-id
on the 4A.
Add the ambient light and proximity sensor on the Asus ZenFone 2
Laser/Selfie.
On Kodiak-based boards, enable the ethernet and USB Type-A ports on the
Rb3Gen2, correct the LT9611 routing on the RubikPi3, add Bluetooth on
the IDP, and add front camera support on the Fairphone FP5.
Introduce an overlay for the Rb3Gen2 Industrial Mezzanine.
Describe DSI on the Monaco SoC and enable Bluetooth, WiFi and DSI/DP
bridge on the Ride board.
Describe the WiFi/BT combo chip properly on the QRB2210 RB1 and QRB4210.
The describe the DSI/DP bringde on the Arduino UnoQ.
01022af2d218 arm64: dts: qcom: sc7280-chrome-common: disable Venus
Introduce DSI display support on SC8280XP.
Add LLCC on SDM670 and another SPI controller on SDM630.
Properly describe the WiFi/BT chip on a variety of SDM845-based
devices. Introduce the "alert slider" on the OnePlus 6 and OnePlus 6T
devices.
Introduce the PRNG, describe the debug UART, and add the MDSS core reset
on SM6125. Enable the debug UART and fix various issues on the Xiaomi
Redmi Note 8. Describe the touchscreen on the Xiaomi Mi A3.
Properly describe the WiFi/BT combo chip in SM8150 HDK.
Improve the EAS properties on SM8550, in addition to various other
fixes. Introduce a new overlay for the HDK display card.
Introduce various smaller fixes across SM8450 and SM8650.
Add display support on SM8750 and enable DSI and DisplayPort on the MTP.
Also add tsens and thermal-zones.
Add ETR devices, flatten the USB controller node, and mark USB
controllers as wakeup-capable devices, on Talos.
Properly describe the IPA IMEM slice on a variety of platforms.
Drop redundant non-controllable regulator definitions from a variety of
boards.
Drop redundant VSYNC pin state definition from various platforms.
* tag 'qcom-arm64-for-7.1' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (254 commits)
arm64: dts: qcom: sm8250: Add missing CPU7 3.09GHz OPP
arm64: dts: qcom: sm8550-hdk: add support for the Display Card overlay
arm64: dts: qcom: msm8916-samsung-coreprimeltevzw: add device tree
dt-bindings: qcom: Document samsung,coreprimeltevzw
arm64: dts: qcom: msm8916-samsung-fortuna: Move SM5504 from rossa and refactor MUIC
arm64: dts: qcom: sdm670: add llcc
arm64: dts: qcom: qcm6490-fairphone-fp5: Add front camera support
arm64: dts: qcom: qcm6490-fairphone-fp5: Sort pinctrl nodes by pins
arm64: dts: qcom: milos-fairphone-fp6: Add camera EEPROMs on CCI busses
arm64: dts: qcom: milos: Add CCI busses
arm64: dts: qcom: purwa-iot-evk: Enable UFS
arm64: dts: qcom: eliza: Add thermal sensors
arm64: dts: qcom: sc8280xp: Add dsi nodes on SC8280XP
arm64: dts: qcom: sdm845-oneplus: Describe Wi-Fi/BT properly
arm64: dts: qcom: sdm845-google: Describe Wi-Fi/BT properly
arm64: dts: qcom: drop redundant zap-shader memory-region
arm64: dts: qcom: fix remaining gpu_zap_shader labels
arm64: dts: qcom: msm8996: fix indentation in sdhc2 node
arm64: dts: qcom: monaco-evk: enable UART6 for robot expansion board
arm64: dts: qcom: lemans-evk: enable UART0 for robot expansion board
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into soc/drivers
Qualcomm driver updates for v7.1
Add ECS LIVA QC710, Glymur CRD, Mahua CRD, Purwa IoT EVK, and Asus
Vivobook to the QSEECOM allow-list, to enable UEFI variable access
through uefisecapp.
Register the Gunyah watchdog device if the SCM driver finds itself
running under Gunyah. Clean up some locking using guards.
Handle possible cases where AOSS cooling state is given a non-boolean
state.
Replace LLCC per-slice activation bitmap with reference counting. Also
add SDM670 support.
Improve probe deferral handling in the OCMEM driver.
Add Milos, QCS615, Eliza, Glymur, and Mahua support to the pd-mapper.
Add support for SoCCP-based pmic-glink, as found in Glymur and
Kaanapali.
Add common QMI service ids to the main qmi headerfile, to avoid
spreading these constants in various drivers.
Add support for version 2 of SMP2P and implement the irqchip state
reading support.
Add CQ7790, SA8650P, SM7450, SM7450P, and IPQ5210 SoC and the PM7550BA
PMIC identifiers to the socinfo driver.
Add Eliza and Mahua support to the UBWC driver, introduce helpers for
drivers to read out min_acc length and other programmable values, and
disable bank swizzling for Glymur.
Simplify the logic related to allocation of NV download request in the
WCNSS control driver.
* tag 'qcom-drivers-for-7.1' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (51 commits)
soc: qcom: ubwc: add helpers to get programmable values
soc: qcom: ubwc: add helper to get min_acc length
firmware: qcom: scm: Register gunyah watchdog device
soc: qcom: socinfo: Add SoC ID for SA8650P
dt-bindings: arm: qcom,ids: Add SoC ID for SA8650P
firmware: qcom: scm: Allow QSEECOM on Mahua CRD
soc: qcom: wcnss: simplify allocation of req
soc: qcom: pd-mapper: Add support for Eliza
soc: qcom: aoss: compare against normalized cooling state
soc: qcom: llcc: fix v1 SB syndrome register offset
dt-bindings: firmware: qcom,scm: Document ipq9650 SCM
soc: qcom: ubwc: Add support for Mahua
soc: qcom: pd-mapper: Add support for Glymur and Mahua
soc: qcom: ubwc: Add configuration Eliza SoC
soc: qcom: ubwc: Remove redundant x1e80100_data
dt-bindings: firmware: qcom,scm: document Eliza SCM Firmware Interface
soc: qcom: ocmem: return -EPROBE_DEFER is ocmem is not available
soc: qcom: ocmem: register reasons for probe deferrals
soc: qcom: ocmem: make the core clock optional
soc: qcom: ubwc: disable bank swizzling for Glymur platform
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
soc/drivers
Reset controller updates for v7.1
* Rework the reset core to support firmware nodes, add more fine
grained locking, and use guard() helpers.
* Change the reset-gpio driver to use firmware nodes.
* Add support for the Cix Sky1 SoC reset controller.
* Add support for the RZ/G3E SoC to the reset-rzv2h-usb2phy driver and
convert it to regmap. Prepare registering a VBUS mux controller.
* Replace use of the deprecated register_restart_handler() function in
the ath79, intel-gw, lpc18xx, ma35d1, npcm, and sunplus reset drivers.
* Combine two allocations into one in the sti/reset-syscfg driver.
* Fix the reset-rzg2l-usbphy-ctrl MODULE_AUTHOR email.
* Fix the reset_control_rearm() kerneldoc comment.
The last commit is a merge of reset-fixes-for-v7.0-2 into reset/next,
to solve a merge conflict between commits a9b95ce36de4 ("reset: gpio: add a
devlink between reset-gpio and its consumer") and fbffb8c7c7bb ("reset: gpio:
fix double free in reset_add_gpio_aux_device() error path").
* tag 'reset-for-v7.1' of https://git.pengutronix.de/git/pza/linux: (35 commits)
reset: rzv2h-usb2phy: Add support for VBUS mux controller registration
reset: rzv2h-usb2phy: Convert to regmap API
dt-bindings: reset: renesas,rzv2h-usb2phy: Document RZ/G3E USB2PHY reset
dt-bindings: reset: renesas,rzv2h-usb2phy: Add '#mux-state-cells' property
reset: core: Drop unnecessary double quote
reset: rzv2h-usb2phy: Keep PHY clock enabled for entire device lifetime
reset: spacemit: k3: Decouple composite reset lines
reset: gpio: fix double free in reset_add_gpio_aux_device() error path
reset: rzg2l-usbphy-ctrl: Fix malformed MODULE_AUTHOR string
reset: sti: kzalloc + kcalloc to kzalloc
reset: don't overwrite fwnode_reset_n_cells
reset: core: Fix indentation
reset: add Sky1 soc reset support
dt-bindings: soc: cix: document the syscon on Sky1 SoC
reset: gpio: make the driver fwnode-agnostic
reset: convert reset core to using firmware nodes
reset: convert the core API to using firmware nodes
reset: convert of_reset_control_get_count() to using firmware nodes
reset: protect struct reset_control with its own mutex
reset: protect struct reset_controller_dev with its own mutex
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into soc/drivers
firmware: tegra: Changes for v7.1-rc1
This introduces a new API for the BPMP to be pass along a specifier from
DT when getting a reference from a phandle. This is used to reference
specific instances of the PCI controller on Tegra264. The ABI header for
BPMP is updated to the latest version and BPMP APIs now use the more
intuitive ENODEV instead of the non SUSV4 ENOTSUPP error code for stub
implementations.
* tag 'tegra-for-7.1-firmware' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
soc/tegra: bpmp: Use ENODEV instead of ENOTSUPP
firmware: tegra: bpmp: Add tegra_bpmp_get_with_id() function
soc/tegra: Update BPMP ABI header
firmware: tegra: bpmp: Rename Tegra239 to Tegra238
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Cross-merge networking fixes after downstream PR (net-7.0-rc7).
Conflicts:
net/vmw_vsock/af_vsock.c
b18c83388874 ("vsock: initialize child_ns_mode_locked in vsock_net_init()")
0de607dc4fd8 ("vsock: add G2H fallback for CIDs not owned by H2G transport")
Adjacent changes:
drivers/net/ethernet/broadcom/bnxt/bnxt_ethtool.c
ceee35e5674a ("bnxt_en: Refactor some basic ring setup and adjustment logic")
57cdfe0dc70b ("bnxt_en: Resize RSS contexts on channel count change")
drivers/net/wireless/intel/iwlwifi/mld/mac80211.c
4d56037a02bd ("wifi: iwlwifi: mld: block EMLSR during TDLS connections")
687a95d204e7 ("wifi: iwlwifi: mld: correctly set wifi generation data")
drivers/net/wireless/intel/iwlwifi/mld/scan.h
b6045c899e37 ("wifi: iwlwifi: mld: Refactor scan command handling")
ec66ec6a5a8f ("wifi: iwlwifi: mld: Fix MLO scan timing")
drivers/net/wireless/intel/iwlwifi/mvm/fw.c
078df640ef05 ("wifi: iwlwifi: mld: add support for iwl_mcc_allowed_ap_type_cmd v
2")
323156c3541e ("wifi: iwlwifi: mvm: don't send a 6E related command when not supported")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"With fixes from wireless, bluetooth and netfilter included we're back
to each PR carrying 30%+ more fixes than in previous era.
The good news is that so far none of the "extra" fixes are themselves
causing real regressions. Not sure how much comfort that is.
Current release - fix to a fix:
- netdevsim: fix build if SKB_EXTENSIONS=n
- eth: stmmac: skip VLAN restore when VLAN hash ops are missing
Previous releases - regressions:
- wifi: iwlwifi: mvm: don't send a 6E related command when
not supported
Previous releases - always broken:
- some info leak fixes
- add missing clearing of skb->cb[] on ICMP paths from tunnels
- ipv6:
- flowlabel: defer exclusive option free until RCU teardown
- avoid overflows in ip6_datagram_send_ctl()
- mpls: add seqcount to protect platform_labels from OOB access
- bridge: improve safety of parsing ND options
- bluetooth: fix leaks, overflows and races in hci_sync
- netfilter: add more input validation, some to address bugs directly
some to prevent exploits from cooking up broken configurations
- wifi:
- ath: avoid poor performance due to stopping the wrong
aggregation session
- virt_wifi: remove SET_NETDEV_DEV to avoid use-after-free
- eth:
- fec: fix the PTP periodic output sysfs interface
- enetc: safely reinitialize TX BD ring when it has unsent frames"
* tag 'net-7.0-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (95 commits)
eth: fbnic: Increase FBNIC_QUEUE_SIZE_MIN to 64
ipv6: avoid overflows in ip6_datagram_send_ctl()
net: hsr: fix VLAN add unwind on slave errors
net: hsr: serialize seq_blocks merge across nodes
vsock: initialize child_ns_mode_locked in vsock_net_init()
selftests/tc-testing: add tests for cls_fw and cls_flow on shared blocks
net/sched: cls_flow: fix NULL pointer dereference on shared blocks
net/sched: cls_fw: fix NULL pointer dereference on shared blocks
net/x25: Fix overflow when accumulating packets
net/x25: Fix potential double free of skb
bnxt_en: Restore default stat ctxs for ULP when resource is available
bnxt_en: Don't assume XDP is never enabled in bnxt_init_dflt_ring_mode()
bnxt_en: Refactor some basic ring setup and adjustment logic
net/mlx5: Fix switchdev mode rollback in case of failure
net/mlx5: Avoid "No data available" when FW version queries fail
net/mlx5: lag: Check for LAG device before creating debugfs
net: macb: properly unregister fixed rate clocks
net: macb: fix clk handling on PCI glue driver removal
virtio_net: clamp rss_max_key_size to NETDEV_RSS_KEY_LEN
net/sched: sch_netem: fix out-of-bounds access in packet corruption
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/iommu/linux
Pull iommu fixes from Joerg Roedel:
- IOMMU-PT related compile breakage in for AMD driver
- IOTLB flushing behavior when unmapped region is larger than requested
due to page-sizes
- Fix IOTLB flush behavior with empty gathers
* tag 'iommu-fixes-v7.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/iommu/linux:
iommupt/amdv1: mark amdv1pt_install_leaf_entry as __always_inline
iommupt: Fix short gather if the unmap goes into a large mapping
iommu: Do not call drivers for empty gathers
|
|
Reset controller fixes for v7.0, part 2
* Decouple spacemit K3 reset lines that were incorrectly coupled
together as one, but are in fact separate resets in hardware.
* Fix a double free in the reset_add_gpio_aux_device() error path.
This has already been fixed on reset/next by commit a9b95ce36de4
("reset: gpio: add a devlink between reset-gpio and its consumer").
* Fix the MODULE_AUTHOR string in the rzg2l-usbphy-ctrl driver.
We merge this into reset/next to resolve a conflict between commits
a9b95ce36de4 ("reset: gpio: add a devlink between reset-gpio and its
consumer") and fbffb8c7c7bb ("reset: gpio: fix double free in
reset_add_gpio_aux_device() error path").
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
cpufreq_cpu_get() can sleep on PREEMPT_RT in presence of concurrent
writer(s), however amd-pstate depends on fetching the cpudata via the
policy's driver data which necessitates grabbing the reference.
Since schedutil governor can call "cpufreq_driver->update_perf()"
during sched_tick/enqueue/dequeue with rq_lock held and IRQs disabled,
fetching the policy object using the cpufreq_cpu_get() helper in the
scheduler fast-path leads to "BUG: scheduling while atomic" on
PREEMPT_RT [1].
Pass the cached cpufreq policy object in sg_policy to the update_perf()
instead of just the CPU. The CPU can be inferred using "policy->cpu".
The lifetime of cpufreq_policy object outlasts that of the governor and
the cpufreq driver (allocated when the CPU is onlined and only reclaimed
when the CPU is offlined / the CPU device is removed) which makes it
safe to be referenced throughout the governor's lifetime.
Closes:https://lore.kernel.org/all/20250731092316.3191-1-spasswolf@web.de/ [1]
Fixes: 1d215f0319c2 ("cpufreq: amd-pstate: Add fast switch function for AMD P-State")
Reported-by: Bert Karwatzki <spasswolf@web.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: K Prateek Nayak <kprateek.nayak@amd.com>
Acked-by: Gary Guo <gary@garyguo.net> # Rust
Reviewed-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Reviewed-by: Zhongqiu Han <zhongqiu.han@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260316081849.19368-3-kprateek.nayak@amd.com
Signed-off-by: Mario Limonciello (AMD) <superm1@kernel.org>
|
|
Srinivas Kandagatla <srinivas.kandagatla@oss.qualcomm.com> says:
This patchset contains few fixes for the bugs hit during testing with
Monza EVK platform
- around array out of bounds access on dai ids which keep extending but
the drivers seems to have hardcoded some numbers, fix this and clean
the mess up
- fix few issues discovered while trying to shut down dsp.
- flooding rpmsg with write requests due to not resetting queue pointer,
fix this resetting the pointer in trigger stop.
- possible multiple graph opens which can result in open failures.
Apart from this few new enhancements to the dsp side
- add new LPI MI2S and senary dai entries
- handle pipewire and Displayport issues by moving graph start to
trigger level, which should fix outstanding pipewire and DP issues on
Qualcomm SoCs.
- remove some unnessary loops in hot path
- support early memory map on DSP.
Tested this on top of linux-next on VENTUNO-Q platform.
|
|
Add new dai ids entries for LPASS LPI MI2S and SENARY MI2S audio lines.
Co-developed-by: Mohammad Rafi Shaik <mohammad.rafi.shaik@oss.qualcomm.com>
Signed-off-by: Mohammad Rafi Shaik <mohammad.rafi.shaik@oss.qualcomm.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@oss.qualcomm.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://patch.msgid.link/20260402081118.348071-7-srinivas.kandagatla@oss.qualcomm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Move a #define so that it is not between kernel-doc and its struct
declaration.
Spell one struct member correctly.
Warning: include/linux/platform_data/apds990x.h:33 #define
APDS_PARAM_SCALE 4096; error: Cannot parse struct or union!
Warning: include/linux/platform_data/apds990x.h:62 struct member
'pdrive' not described in 'apds990x_platform_data'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://patch.msgid.link/20260226051207.547152-1-rdunlap@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
xHCI hardware maintains its endpoint state between add_endpoint()
and drop_endpoint() calls followed by successful check_bandwidth().
So does the driver.
Core may call endpoint_disable() during xHCI endpoint life, so don't
clear host_ep->hcpriv then, because this breaks endpoint_reset().
If a driver calls usb_set_interface(), submits URBs which make host
sequence state non-zero and calls usb_clear_halt(), the device clears
its sequence state but xhci_endpoint_reset() bails out. The next URB
malfunctions: USB2 loses one packet, USB3 gets Transaction Error or
may not complete at all on some (buggy?) HCs from ASMedia and AMD.
This is triggered by uvcvideo on bulk video devices.
The code was copied from ehci_endpoint_disable() but it isn't needed
here - hcpriv should only be NULL on emulated root hub endpoints.
It might prevent resetting and inadvertently enabling a disabled and
dropped endpoint, but core shouldn't try to reset dropped endpoints.
Document xhci requirements regarding hcpriv. They are currently met.
Fixes: 18b74067ac78 ("xhci: Fix use-after-free regression in xhci clear hub TT implementation")
Cc: stable@vger.kernel.org
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://patch.msgid.link/20260402131342.2628648-26-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Switched struct pointer member to a flexible array member to get rid of
kzalloc_objs as there's no need for them to be separately allocated.
AAdded __counted_by for extra runtime analysis.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://patch.msgid.link/20260311232459.18407-1-rosenp@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There is an existing comedi_request_region(dev, start, len) function
used by COMEDI drivers for legacy devices to request an I/O port region
starting at a specified base address (which must be non-zero) and with a
specified length. It uses request_region(). On success, it sets
dev->iobase and dev->iolen and returns 0. There is a alternative
function __comedi_request_region(dev, start, len) which does the same
thing without setting dev->iobase and dev->iolen.
Most hardware devices have restrictions on the allowed I/O port base
address and alignment, so add new functions
comedi_check_request_region(dev, start, len, minstart, maxend, minalign)
and __comedi_check_request_region(dev, start, len, minstart, maxend,
minalign) to perform these additional checks. Turn the original
functions into static inline wrapper functions that call the new
functions.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://patch.msgid.link/20260130170416.49994-2-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Now that all the bits are properly addressed, provide a mechanism
for testing ESA mode guests in nested configurations.
Signed-off-by: Hendrik Brueckner <brueckner@linux.ibm.com>
[farman@us.ibm.com: Updated commit message]
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
Signed-off-by: Eric Farman <farman@linux.ibm.com>
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
|
|
The following fix in sched/urgent:
e08d007f9d81 ("sched/debug: Fix avg_vruntime() usage")
is in conflict with this pending commit in sched/core:
4823725d9d1d ("sched/fair: Increase weight bits for avg_vruntime")
Both modify the same variable definition and initialization blocks,
resolve it by merging the two.
Conflicts:
kernel/sched/debug.c
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Rather than querying the output device for its address in
mctp_local_output, set up the source address when we're populating the
dst structure. If no address is assigned, use MCTP_ADDR_NULL.
This will allow us more flexibility when routing for NULL-source-eid
cases. For now though, we still reject a NULL source address in the
output path.
We need to update the tests a little, so that addresses are assigned
before we do the dst lookups.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Link: https://patch.msgid.link/20260331-dev-mctp-null-eids-v1-1-b4d047372eaf@codeconstruct.com.au
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Making ->d_rcu and (then) ->d_child overlapping dates back to
2006; anon unions support had been added to gcc only in 4.6
(2011) and the minimal gcc version hadn't been bumped to that
until 4.19 (2018).
These days there's no reason not to keep that union named.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Move the driver specific fbdev fb calls to the display parent
interface. Reuse the existing struct intel_display_bo_interface, as this
is mostly about gem objects.
Put everything behind IS_ENABLED(CONFIG_DRM_FBDEV_EMULATION) to catch
configuration issues at build or link time.
v2: Rebase
Reviewed-by: Michał Grzelak <michal.grzelak@intel.com> # v1
Link: https://patch.msgid.link/a6bb24909a58181cfc41b91a4c6538a181d27158.1774950508.git.jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Most of the places using d_alias are loops iterating through all aliases for
given inode; introduce a helper macro (for_each_alias(dentry, inode))
and convert open-coded instances of such loop to it.
They are easier to read that way and it reduces the noise on the next steps.
You _must_ hold inode->i_lock over that thing.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Replace the coarse USB device lock with a dedicated offload_lock
spinlock to reduce contention during offload operations. Use
offload_pm_locked to synchronize with PM transitions and replace
the legacy offload_at_suspend flag.
Optimize usb_offload_get/put by switching from auto-resume/suspend
to pm_runtime_get_if_active(). This ensures offload state is only
modified when the device is already active, avoiding unnecessary
power transitions.
Cc: stable <stable@kernel.org>
Fixes: ef82a4803aab ("xhci: sideband: add api to trace sideband usage")
Signed-off-by: Guan-Yu Lin <guanyulin@google.com>
Tested-by: Hailong Liu <hailong.liu@oppo.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://patch.msgid.link/20260401123238.3790062-2-guanyulin@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch introduces support for operating the Cadence USBSSP (cdnsp)
controller in a peripheral-only mode, bypassing the Dual-Role Device (DRD)
logic.
The change in BAR indexing (from BAR 2 to BAR 1) is a direct
consequence of switching from 64-bit to 32-bit addressing in the
Peripheral-only configuration.
Tested on PCI platform with Device-only configuration. Platform-side
changes are included to support the PCI glue layer's property injection.
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> # pci_ids.h
Link: https://patch.msgid.link/20260331-device_only-v1-1-00378b80365c@cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix comment style for enums so they're kernel-doc compliant.
Signed-off-by: Amit Sunil Dhamne <amitsd@google.com>
Link: https://patch.msgid.link/20260401-fix-mfd-max77759-usb-next-v1-1-174ec23ad824@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Current CC designs don't place a vIOMMU in front of untrusted devices.
Instead, the DMA API forces all untrusted device DMA through swiotlb
bounce buffers (is_swiotlb_force_bounce()) which copies data into
shared memory on behalf of the device.
When a caller has already arranged for the memory to be shared
via set_memory_decrypted(), the DMA API needs to know so it can map
directly using the unencrypted physical address rather than bounce
buffering. Following the pattern of DMA_ATTR_MMIO, add
DMA_ATTR_CC_SHARED for this purpose. Like the MMIO case, only the
caller knows what kind of memory it has and must inform the DMA API
for it to work correctly.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Acked-by: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20260325192352.437608-2-jiri@resnulli.us
|
|
The function helps to XOR bitmaps and calculate Hamming weight of
the result in one pass.
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Yury Norov <ynorov@nvidia.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jenswi/linux-tee into soc/drivers
TEE update for 7.1
Clean up tee_core.h kernel-doc to eliminate build warnings
* tag 'tee-for-v7.1' of git://git.kernel.org/pub/scm/linux/kernel/git/jenswi/linux-tee:
tee: clean up tee_core.h kernel-doc
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into soc/drivers
STM32 Firewall bus for v7.1, round 1
Highlights:
----------
Stm32 SoCs embed debug peripherals such as Coresight. These peripherals
can monitor the activity of the cores. Because of that, they can be
used only if some features in the debug configuration are enabled.
Else, errors or firewall exceptions can be observed. Similarly to
the ETZPC(on stm32mp1x platforms) or the RIFSC(on stm32mp2x platforms),
debug-related peripherals access can be assessed at bus level to
prevent these issues from happening.
The debug configuration can only be accessed by the secure world.
That means that a service must be implemented in the secure world for
the kernel to check the firewall configuration. On OpenSTLinux, it is
done through a Debug access PTA in OP-TEE [1].
To represent the debug peripherals present on a dedicated debug bus,
create a debug bus node in the device tree and the associated driver
that will interact with this PTA.
Plus some fixes.
* tag 'stm32-bus-firewall-for-7.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32:
pinctrl: stm32: add firewall checks before probing the HDP driver
drivers: bus: add the stm32 debug bus driver
bus: stm32_firewall: add stm32_firewall_get_grant_all_access() API
bus: stm32_firewall: allow check on different firewall controllers
dt-bindings: bus: document the stm32 debug bus
dt-bindings: pinctrl: document access-controllers property for stm32 HDP
dt-bindings: document access-controllers property for coresight peripherals
bus: rifsc: fix RIF configuration check for peripherals
bus: rifsc: Replace snprintf("%s") with strscpy
bus: stm32_firewall: Simplify with scoped for each OF child loop
bus: firewall: move stm32_firewall header file in include folder
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-mem-ctrl into soc/drivers
Memory controller drivers for v7.1
1. TegraMC:
- Few fixes for older issues - missing clock on Tegra264,
missing enabling of DLL for Tegra30 and Tegra124.
- Simplify the code in a few places.
- Rework handling interrupts on different variants and add support for
error logging on Tegra 264.
2. Drop Baikal SoC bt1-l2-ctl driver, because SoC support is being
removed tree-wide.
* tag 'memory-controller-drv-7.1' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-mem-ctrl:
memory: tegra: Add MC error logging support for Tegra264
memory: tegra: Prepare for supporting multiple intmask registers
memory: tegra: Group SoC specific fields
memory: tegra: Add support for multiple IRQs
memory: tegra: Group register and fields
memory: tegra: Group error handling related registers
memory: tegra-mc: Use %pe format
memory: tegra-mc: Simplify printing PTR_ERR with dev_err_probe
memory: tegra-mc: Drop tegra_mc_setup_latency_allowance() return value
memory: renesas-rpc-if: Simplify printing PTR_ERR with dev_err_probe
memory: brcmstb_memc: Expand LPDDR4 check to cover for LPDDR5
dt-bindings: cache: bt1-l2-ctl: Remove unused bindings
memory: bt1-l2-ctl: Remove not-going-to-be-supported code for Baikal SoC
memory: tegra30-emc: Fix dll_change check
memory: tegra124-emc: Fix dll_change check
memory: tegra: Add support for DBB clock on Tegra264
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
On systems where many CPUs share one LLC, unbound workqueues using
WQ_AFFN_CACHE collapse to a single worker pool, causing heavy spinlock
contention on pool->lock. For example, Chuck Lever measured 39% of
cycles lost to native_queued_spin_lock_slowpath on a 12-core shared-L3
NFS-over-RDMA system.
The existing affinity hierarchy (cpu, smt, cache, numa, system) offers
no intermediate option between per-LLC and per-SMT-core granularity.
Add WQ_AFFN_CACHE_SHARD, which subdivides each LLC into groups of at
most wq_cache_shard_size cores (default 8, tunable via boot parameter).
Shards are always split on core (SMT group) boundaries so that
Hyper-Threading siblings are never placed in different pods. Cores are
distributed across shards as evenly as possible -- for example, 36 cores
in a single LLC with max shard size 8 produces 5 shards of 8+7+7+7+7
cores.
The implementation follows the same comparator pattern as other affinity
scopes: precompute_cache_shard_ids() pre-fills the cpu_shard_id[] array
from the already-initialized WQ_AFFN_CACHE and WQ_AFFN_SMT topology,
and cpus_share_cache_shard() is passed to init_pod_type().
Benchmark on NVIDIA Grace (72 CPUs, single LLC, 50k items/thread), show
cache_shard delivers ~5x the throughput and ~6.5x lower p50 latency
compared to cache scope on this 72-core single-LLC system.
Suggested-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Fix "poer" -> "per" in the WQ_AFFN_SMT enum comment.
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Since commit aefbab8e77eb ("arm64: fpsimd: Preserve/restore kernel mode
NEON at context switch"), kernel-mode NEON sections have been
preemptible on arm64. And since commit 7dadeaa6e851 ("sched: Further
restrict the preemption modes"), voluntary preemption is no longer
supported on arm64 either. Therefore, there's no longer any need to
limit the length of kernel-mode NEON sections on arm64.
Simplify the AES-CBC-MAC code accordingly.
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20260401000548.133151-2-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
|
|
Since commit 3a3f61ce5e0b ("exec: Make sure task->comm is always
NUL-terminated"), __set_task_comm() is unlocked and no longer uses
strscpy_pad() - update the stale comment accordingly.
Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev>
Link: https://patch.msgid.link/20260401152039.724811-4-thorsten.blum@linux.dev
Signed-off-by: Kees Cook <kees@kernel.org>
|
