kernel/git/stable/linux.git/arch/mips, branch linux-5.13.y

MIPS: Malta: fix alignment of the devicetree buffer

2021-09-18T11:41:57+00:00

[ Upstream commit bea6a94a279bcbe6b2cde348782b28baf12255a5 ] Starting with following patch MIPS Malta is not able to boot: | commit 79edff12060fe7772af08607eff50c0e2486c5ba | Author: Rob Herring | scripts/dtc: Update to upstream version v1.6.0-51-g183df9e9c2b9 The reason is the alignment test added to the fdt_ro_probe_(). To fix this issue, we need to make sure that fdt_buf is aligned. Since the dtc patch was designed to uncover potential issue, I handle initial MIPS Malta patch as initial bug. Fixes: e81a8c7dabac ("MIPS: Malta: Setup RAM regions via DT") Signed-off-by: Oleksij Rempel Signed-off-by: Thomas Bogendoerfer Signed-off-by: Sasha Levin

MIPS: Malta: Do not byte-swap accesses to the CBUS UART

2021-08-12T11:32:20+00:00

commit 9a936d6c3d3d6c33ecbadf72dccdb567b5cd3c72 upstream. Correct big-endian accesses to the CBUS UART, a Malta on-board discrete TI16C550C part wired directly to the system controller's device bus, and do not use byte swapping with the 32-bit accesses to the device. The CBUS is used for devices such as the boot flash memory needed early on in system bootstrap even before PCI has been initialised. Therefore it uses the system controller's device bus, which follows the endianness set with the CPU, which means no byte-swapping is ever required for data accesses to CBUS, unlike with PCI. The CBUS UART uses the UPIO_MEM32 access method, that is the `readl' and `writel' MMIO accessors, which on the MIPS platform imply byte-swapping with PCI systems. Consequently the wrong byte lane is accessed with the big-endian configuration and the UART is not correctly accessed. As it happens the UPIO_MEM32BE access method makes use of the `ioread32' and `iowrite32' MMIO accessors, which still use `readl' and `writel' respectively, however they byte-swap data passed, effectively cancelling swapping done with the accessors themselves and making it suitable for the CBUS UART. Make the CBUS UART switch between UPIO_MEM32 and UPIO_MEM32BE then, based on the endianness selected. With this change in place the device is correctly recognised with big-endian Malta at boot, along with the Super I/O devices behind PCI: Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled printk: console [ttyS0] disabled serial8250.0: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A printk: console [ttyS0] enabled printk: bootconsole [uart8250] disabled serial8250.0: ttyS1 at I/O 0x2f8 (irq = 3, base_baud = 115200) is a 16550A serial8250.0: ttyS2 at MMIO 0x1f000900 (irq = 20, base_baud = 230400) is a 16550A Fixes: e7c4782f92fc ("[MIPS] Put an end to 's long and annyoing existence") Cc: stable@vger.kernel.org # v2.6.23+ Reviewed-by: Philippe Mathieu-Daudé Signed-off-by: Maciej W. Rozycki Link: https://lore.kernel.org/r/alpine.DEB.2.21.2106260524430.37803@angie.orcam.me.uk Signed-off-by: Greg Kroah-Hartman

mips: Fix non-POSIX regexp

2021-08-12T11:32:10+00:00

[ Upstream commit 28bbbb9875a35975904e46f9b06fa689d051b290 ] When cross compiling a MIPS kernel on a BSD based HOSTCC leads to errors like SYNC include/config/auto.conf.cmd - due to: .config egrep: empty (sub)expression UPD include/config/kernel.release HOSTCC scripts/dtc/dtc.o - due to target missing It turns out that egrep uses this egrep pattern: (|MINOR_|PATCHLEVEL_) This is not valid syntax or gives undefined results according to POSIX 9.5.3 ERE Grammar https://pubs.opengroup.org/onlinepubs/9699919799/basedefs/V1_chap09.html It seems to be silently accepted by the Linux egrep implementation while a BSD host complains. Such patterns can be replaced by a transformation like "(|p1|p2)" -> "(p1|p2)?" Fixes: 48c35b2d245f ("[MIPS] There is no __GNUC_MAJOR__") Signed-off-by: H. Nikolaus Schaller Signed-off-by: Masahiro Yamada Signed-off-by: Sasha Levin

MIPS: check return value of pgtable_pmd_page_ctor

2021-08-12T11:32:10+00:00

[ Upstream commit 6aa32467299e9e12280a6aec9dbc21bf2db830b0 ] +. According to Documentation/vm/split_page_table_lock, handle failure of pgtable_pmd_page_ctor +. Use GFP_KERNEL_ACCOUNT instead of GFP_KERNEL|__GFP_ACCOUNT +. Adjust coding style Fixes: ed914d48b6a1 ("MIPS: add PMD table accounting into MIPS') Reported-by: Joshua Kinard Signed-off-by: Huang Pei Reviewed-by: Joshua Kinard Signed-off-by: Thomas Bogendoerfer Signed-off-by: Sasha Levin

bpf: Introduce BPF nospec instruction for mitigating Spectre v4

2021-08-04T10:47:56+00:00

[ Upstream commit f5e81d1117501546b7be050c5fbafa6efd2c722c ] In case of JITs, each of the JIT backends compiles the BPF nospec instruction /either/ to a machine instruction which emits a speculation barrier /or/ to /no/ machine instruction in case the underlying architecture is not affected by Speculative Store Bypass or has different mitigations in place already. This covers both x86 and (implicitly) arm64: In case of x86, we use 'lfence' instruction for mitigation. In case of arm64, we rely on the firmware mitigation as controlled via the ssbd kernel parameter. Whenever the mitigation is enabled, it works for all of the kernel code with no need to provide any additional instructions here (hence only comment in arm64 JIT). Other archs can follow as needed. The BPF nospec instruction is specifically targeting Spectre v4 since i) we don't use a serialization barrier for the Spectre v1 case, and ii) mitigation instructions for v1 and v4 might be different on some archs. The BPF nospec is required for a future commit, where the BPF verifier does annotate intermediate BPF programs with speculation barriers. Co-developed-by: Piotr Krysiuk Co-developed-by: Benedict Schlueter Signed-off-by: Daniel Borkmann Signed-off-by: Piotr Krysiuk Signed-off-by: Benedict Schlueter Acked-by: Alexei Starovoitov Signed-off-by: Sasha Levin

MIPS: vdso: Invalid GIC access through VDSO

2021-07-20T14:00:42+00:00

[ Upstream commit 47ce8527fbba145a7723685bc9a27d9855e06491 ] Accessing raw timers (currently only CLOCK_MONOTONIC_RAW) through VDSO doesn't return the correct time when using the GIC as clock source. The address of the GIC mapped page is in this case not calculated correctly. The GIC mapped page is calculated from the VDSO data by subtracting PAGE_SIZE: void *get_gic(const struct vdso_data *data) { return (void __iomem *)data - PAGE_SIZE; } However, the data pointer is not page aligned for raw clock sources. This is because the VDSO data for raw clock sources (CS_RAW = 1) is stored after the VDSO data for coarse clock sources (CS_HRES_COARSE = 0). Therefore, only the VDSO data for CS_HRES_COARSE is page aligned: +--------------------+ | | | vd[CS_RAW] | ---+ | vd[CS_HRES_COARSE] | | +--------------------+ | -PAGE_SIZE | | | | GIC mapped page | <--+ | | +--------------------+ When __arch_get_hw_counter() is called with &vd[CS_RAW], get_gic returns the wrong address (somewhere inside the GIC mapped page). The GIC counter values are not returned which results in an invalid time. Fixes: a7f4df4e21dd ("MIPS: VDSO: Add implementations of gettimeofday() and clock_gettime()") Signed-off-by: Martin Fäcknitz Signed-off-by: Thomas Bogendoerfer Signed-off-by: Sasha Levin

mips: disable branch profiling in boot/decompress.o

2021-07-20T14:00:42+00:00

[ Upstream commit 97e488073cfca0eea84450169ca4cbfcc64e33e3 ] Use DISABLE_BRANCH_PROFILING for arch/mips/boot/compressed/decompress.o to prevent linkage errors. mips64-linux-ld: arch/mips/boot/compressed/decompress.o: in function `LZ4_decompress_fast_extDict': decompress.c:(.text+0x8c): undefined reference to `ftrace_likely_update' mips64-linux-ld: decompress.c:(.text+0xf4): undefined reference to `ftrace_likely_update' mips64-linux-ld: decompress.c:(.text+0x200): undefined reference to `ftrace_likely_update' mips64-linux-ld: decompress.c:(.text+0x230): undefined reference to `ftrace_likely_update' mips64-linux-ld: decompress.c:(.text+0x320): undefined reference to `ftrace_likely_update' mips64-linux-ld: arch/mips/boot/compressed/decompress.o:decompress.c:(.text+0x3f4): more undefined references to `ftrace_likely_update' follow Fixes: e76e1fdfa8f8 ("lib: add support for LZ4-compressed kernel") Reported-by: kernel test robot Signed-off-by: Randy Dunlap Cc: Thomas Bogendoerfer Cc: linux-mips@vger.kernel.org Cc: Kyungsik Lee Signed-off-by: Thomas Bogendoerfer Signed-off-by: Sasha Levin

mips: always link byteswap helpers into decompressor

2021-07-20T14:00:41+00:00

[ Upstream commit cddc40f5617e53f97ef019d5b29c1bd6cbb031ec ] My series to clean up the unaligned access implementation across architectures caused some mips randconfig builds to fail with: mips64-linux-ld: arch/mips/boot/compressed/decompress.o: in function `decompress_kernel': decompress.c:(.text.decompress_kernel+0x54): undefined reference to `__bswapsi2' It turns out that this problem has already been fixed for the XZ decompressor but now it also shows up in (at least) LZO and LZ4. From my analysis I concluded that the compiler could always have emitted those calls, but the different implementation allowed it to make otherwise better decisions about not inlining the byteswap, which results in the link error when the out-of-line code is missing. While it could be addressed by adding it to the two decompressor implementations that are known to be affected, but as this only adds 112 bytes to the kernel, the safer choice is to always add them. Fixes: c50ec6787536 ("MIPS: zboot: Fix the build with XZ compression on older GCC versions") Fixes: 0652035a5794 ("asm-generic: unaligned: remove byteshift helpers") Link: https://lore.kernel.org/linux-mm/202106301304.gz2wVY9w-lkp@intel.com/ Link: https://lore.kernel.org/linux-mm/202106260659.TyMe8mjr-lkp@intel.com/ Link: https://lore.kernel.org/linux-mm/202106172016.onWT6Tza-lkp@intel.com/ Link: https://lore.kernel.org/linux-mm/202105231743.JJcALnhS-lkp@intel.com/ Signed-off-by: Arnd Bergmann Signed-off-by: Thomas Bogendoerfer Signed-off-by: Sasha Levin

MIPS: MT extensions are not available on MIPS32r1

2021-07-19T08:04:47+00:00

commit cad065ed8d8831df67b9754cc4437ed55d8b48c0 upstream. MIPS MT extensions were added with the MIPS 34K processor, which was based on the MIPS32r2 ISA. This fixes a build error when building a generic kernel for a MIPS32r1 CPU. Fixes: c434b9f80b09 ("MIPS: Kconfig: add MIPS_GENERIC_KERNEL symbol") Cc: stable@vger.kernel.org # v5.9 Signed-off-by: Paul Cercueil Signed-off-by: Thomas Bogendoerfer Signed-off-by: Greg Kroah-Hartman

MIPS: CI20: Reduce clocksource to 750 kHz.

2021-07-19T08:04:47+00:00

[ Upstream commit 23c64447b3538a6f34cb38aae3bc19dc1ec53436 ] The original clock (3 MHz) is too fast for the clocksource, there will be a chance that the system may get stuck. Reported-by: Nikolaus Schaller Tested-by: Nikolaus Schaller # on CI20 Signed-off-by: 周琰杰 (Zhou Yanjie) Acked-by: Paul Cercueil Signed-off-by: Thomas Bogendoerfer Signed-off-by: Sasha Levin