kernel/git/stable/linux.git/drivers/net/usb, branch linux-4.14.y

net: usb: qmi_wwan: claim interface 4 for ZTE MF290

2023-12-20T14:32:37+00:00

[ Upstream commit 99360d9620f09fb8bc15548d855011bbb198c680 ] Interface 4 is used by for QMI interface in stock firmware of MF28D, the router which uses MF290 modem. Rebind it to qmi_wwan after freeing it up from option driver. The proper configuration is: Interface mapping is: 0: QCDM, 1: (unknown), 2: AT (PCUI), 2: AT (Modem), 4: QMI T: Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#= 4 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=19d2 ProdID=0189 Rev= 0.00 S: Manufacturer=ZTE, Incorporated S: Product=ZTE LTE Technologies MSM C:* #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=84(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan E: Ad=86(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms Cc: Bjørn Mork Signed-off-by: Lech Perczak Link: https://lore.kernel.org/r/20231117231918.100278-3-lech.perczak@gmail.com Signed-off-by: Paolo Abeni Signed-off-by: Sasha Levin

net: usb: ax88179_178a: fix failed operations during ax88179_reset

2023-12-08T07:41:59+00:00

[ Upstream commit 0739af07d1d947af27c877f797cb82ceee702515 ] Using generic ASIX Electronics Corp. AX88179 Gigabit Ethernet device, the following test cycle has been implemented: - power on - check logs - shutdown - after detecting the system shutdown, disconnect power - after approximately 60 seconds of sleep, power is restored Running some cycles, sometimes error logs like this appear: kernel: ax88179_178a 2-9:1.0 (unnamed net_device) (uninitialized): Failed to write reg index 0x0001: -19 kernel: ax88179_178a 2-9:1.0 (unnamed net_device) (uninitialized): Failed to read reg index 0x0001: -19 ... These failed operation are happening during ax88179_reset execution, so the initialization could not be correct. In order to avoid this, we need to increase the delay after reset and clock initial operations. By using these larger values, many cycles have been run and no failed operations appear. It would be better to check some status register to verify when the operation has finished, but I do not have found any available information (neither in the public datasheets nor in the manufacturer's driver). The only available information for the necessary delays is the maufacturer's driver (original values) but the proposed values are not enough for the tested devices. Fixes: e2ca90c276e1f ("ax88179_178a: ASIX AX88179_178A USB 3.0/2.0 to gigabit ethernet adapter driver") Reported-by: Herb Wei Tested-by: Herb Wei Signed-off-by: Jose Ignacio Tornos Martinez Link: https://lore.kernel.org/r/20231120120642.54334-1-jtornosm@redhat.com Signed-off-by: Jakub Kicinski Signed-off-by: Sasha Levin

r8152: Increase USB control msg timeout to 5000ms as per spec

2023-11-08T10:21:05+00:00

[ Upstream commit a5feba71ec9c14a54c3babdc732c5b6866d8ee43 ] According to the comment next to USB_CTRL_GET_TIMEOUT and USB_CTRL_SET_TIMEOUT, although sending/receiving control messages is usually quite fast, the spec allows them to take up to 5 seconds. Let's increase the timeout in the Realtek driver from 500ms to 5000ms (using the #defines) to account for this. This is not just a theoretical change. The need for the longer timeout was seen in testing. Specifically, if you drop a sc7180-trogdor based Chromebook into the kdb debugger and then "go" again after sitting in the debugger for a while, the next USB control message takes a long time. Out of ~40 tests the slowest USB control message was 4.5 seconds. While dropping into kdb is not exactly an end-user scenario, the above is similar to what could happen due to an temporary interrupt storm, what could happen if there was a host controller (HW or SW) issue, or what could happen if the Realtek device got into a confused state and needed time to recover. This change is fairly critical since the r8152 driver in Linux doesn't expect register reads/writes (which are backed by USB control messages) to fail. Fixes: ac718b69301c ("net/usb: new driver for RTL8152") Suggested-by: Hayes Wang Signed-off-by: Douglas Anderson Reviewed-by: Grant Grundler Signed-off-by: David S. Miller Signed-off-by: Sasha Levin

net: usb: smsc95xx: Fix an error code in smsc95xx_reset()

2023-10-25T09:13:32+00:00

commit c53647a5df9e66dd9fedf240198e1fe50d88c286 upstream. Return a negative error code instead of success. Fixes: 2f7ca802bdae ("net: Add SMSC LAN9500 USB2.0 10/100 ethernet adapter driver") Signed-off-by: Dan Carpenter Reviewed-by: Andrew Lunn Link: https://lore.kernel.org/r/147927f0-9ada-45cc-81ff-75a19dd30b76@moroto.mountain Signed-off-by: Jakub Kicinski Signed-off-by: Greg Kroah-Hartman

net: usb: dm9601: fix uninitialized variable use in dm9601_mdio_read

2023-10-25T09:13:30+00:00

commit 8f8abb863fa5a4cc18955c6a0e17af0ded3e4a76 upstream. syzbot has found an uninit-value bug triggered by the dm9601 driver [1]. This error happens because the variable res is not updated if the call to dm_read_shared_word returns an error. In this particular case -EPROTO was returned and res stayed uninitialized. This can be avoided by checking the return value of dm_read_shared_word and propagating the error if the read operation failed. [1] https://syzkaller.appspot.com/bug?extid=1f53a30781af65d2c955 Cc: stable@vger.kernel.org Signed-off-by: Javier Carrasco Reported-and-tested-by: syzbot+1f53a30781af65d2c955@syzkaller.appspotmail.com Acked-by: Peter Korsgaard Fixes: d0374f4f9c35cdfbee0 ("USB: Davicom DM9601 usbnet driver") Link: https://lore.kernel.org/r/20231009-topic-dm9601_uninit_mdio_read-v2-1-f2fe39739b6c@gmail.com Signed-off-by: Jakub Kicinski Signed-off-by: Greg Kroah-Hartman

net: usb: smsc75xx: Fix uninit-value access in __smsc75xx_read_reg

2023-10-10T19:43:41+00:00

[ Upstream commit e9c65989920f7c28775ec4e0c11b483910fb67b8 ] syzbot reported the following uninit-value access issue: ===================================================== BUG: KMSAN: uninit-value in smsc75xx_wait_ready drivers/net/usb/smsc75xx.c:975 [inline] BUG: KMSAN: uninit-value in smsc75xx_bind+0x5c9/0x11e0 drivers/net/usb/smsc75xx.c:1482 CPU: 0 PID: 8696 Comm: kworker/0:3 Not tainted 5.8.0-rc5-syzkaller #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Workqueue: usb_hub_wq hub_event Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x21c/0x280 lib/dump_stack.c:118 kmsan_report+0xf7/0x1e0 mm/kmsan/kmsan_report.c:121 __msan_warning+0x58/0xa0 mm/kmsan/kmsan_instr.c:215 smsc75xx_wait_ready drivers/net/usb/smsc75xx.c:975 [inline] smsc75xx_bind+0x5c9/0x11e0 drivers/net/usb/smsc75xx.c:1482 usbnet_probe+0x1152/0x3f90 drivers/net/usb/usbnet.c:1737 usb_probe_interface+0xece/0x1550 drivers/usb/core/driver.c:374 really_probe+0xf20/0x20b0 drivers/base/dd.c:529 driver_probe_device+0x293/0x390 drivers/base/dd.c:701 __device_attach_driver+0x63f/0x830 drivers/base/dd.c:807 bus_for_each_drv+0x2ca/0x3f0 drivers/base/bus.c:431 __device_attach+0x4e2/0x7f0 drivers/base/dd.c:873 device_initial_probe+0x4a/0x60 drivers/base/dd.c:920 bus_probe_device+0x177/0x3d0 drivers/base/bus.c:491 device_add+0x3b0e/0x40d0 drivers/base/core.c:2680 usb_set_configuration+0x380f/0x3f10 drivers/usb/core/message.c:2032 usb_generic_driver_probe+0x138/0x300 drivers/usb/core/generic.c:241 usb_probe_device+0x311/0x490 drivers/usb/core/driver.c:272 really_probe+0xf20/0x20b0 drivers/base/dd.c:529 driver_probe_device+0x293/0x390 drivers/base/dd.c:701 __device_attach_driver+0x63f/0x830 drivers/base/dd.c:807 bus_for_each_drv+0x2ca/0x3f0 drivers/base/bus.c:431 __device_attach+0x4e2/0x7f0 drivers/base/dd.c:873 device_initial_probe+0x4a/0x60 drivers/base/dd.c:920 bus_probe_device+0x177/0x3d0 drivers/base/bus.c:491 device_add+0x3b0e/0x40d0 drivers/base/core.c:2680 usb_new_device+0x1bd4/0x2a30 drivers/usb/core/hub.c:2554 hub_port_connect drivers/usb/core/hub.c:5208 [inline] hub_port_connect_change drivers/usb/core/hub.c:5348 [inline] port_event drivers/usb/core/hub.c:5494 [inline] hub_event+0x5e7b/0x8a70 drivers/usb/core/hub.c:5576 process_one_work+0x1688/0x2140 kernel/workqueue.c:2269 worker_thread+0x10bc/0x2730 kernel/workqueue.c:2415 kthread+0x551/0x590 kernel/kthread.c:292 ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:293 Local variable ----buf.i87@smsc75xx_bind created at: __smsc75xx_read_reg drivers/net/usb/smsc75xx.c:83 [inline] smsc75xx_wait_ready drivers/net/usb/smsc75xx.c:968 [inline] smsc75xx_bind+0x485/0x11e0 drivers/net/usb/smsc75xx.c:1482 __smsc75xx_read_reg drivers/net/usb/smsc75xx.c:83 [inline] smsc75xx_wait_ready drivers/net/usb/smsc75xx.c:968 [inline] smsc75xx_bind+0x485/0x11e0 drivers/net/usb/smsc75xx.c:1482 This issue is caused because usbnet_read_cmd() reads less bytes than requested (zero byte in the reproducer). In this case, 'buf' is not properly filled. This patch fixes the issue by returning -ENODATA if usbnet_read_cmd() reads less bytes than requested. Fixes: d0cad871703b ("smsc75xx: SMSC LAN75xx USB gigabit ethernet adapter driver") Reported-and-tested-by: syzbot+6966546b78d050bb0b5d@syzkaller.appspotmail.com Closes: https://syzkaller.appspot.com/bug?extid=6966546b78d050bb0b5d Signed-off-by: Shigeru Yoshida Reviewed-by: Simon Horman Link: https://lore.kernel.org/r/20230923173549.3284502-1-syoshida@redhat.com Signed-off-by: Paolo Abeni Signed-off-by: Sasha Levin

net: usb: qmi_wwan: add Quectel EM05GV2

2023-09-23T08:46:53+00:00

[ Upstream commit d4480c9bb9258db9ddf2e632f6ef81e96b41089c ] Add support for Quectel EM05GV2 (G=global) with vendor ID 0x2c7c and product ID 0x030e Enabling DTR on this modem was necessary to ensure stable operation. Patch for usb: serial: option: is also in progress. T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=2c7c ProdID=030e Rev= 3.18 S: Manufacturer=Quectel S: Product=Quectel EM05-G C:* #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan E: Ad=89(I) Atr=03(Int.) MxPS= 8 Ivl=32ms E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms Signed-off-by: Martin Kohn Link: https://lore.kernel.org/r/AM0PR04MB57648219DE893EE04FA6CC759701A@AM0PR04MB5764.eurprd04.prod.outlook.com Signed-off-by: Jakub Kicinski Signed-off-by: Sasha Levin

net: usbnet: Fix WARNING in usbnet_start_xmit/usb_submit_urb

2023-08-11T09:33:56+00:00

commit 5e1627cb43ddf1b24b92eb26f8d958a3f5676ccb upstream. The syzbot fuzzer identified a problem in the usbnet driver: usb 1-1: BOGUS urb xfer, pipe 3 != type 1 WARNING: CPU: 0 PID: 754 at drivers/usb/core/urb.c:504 usb_submit_urb+0xed6/0x1880 drivers/usb/core/urb.c:504 Modules linked in: CPU: 0 PID: 754 Comm: kworker/0:2 Not tainted 6.4.0-rc7-syzkaller-00014-g692b7dc87ca6 #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 05/27/2023 Workqueue: mld mld_ifc_work RIP: 0010:usb_submit_urb+0xed6/0x1880 drivers/usb/core/urb.c:504 Code: 7c 24 18 e8 2c b4 5b fb 48 8b 7c 24 18 e8 42 07 f0 fe 41 89 d8 44 89 e1 4c 89 ea 48 89 c6 48 c7 c7 a0 c9 fc 8a e8 5a 6f 23 fb <0f> 0b e9 58 f8 ff ff e8 fe b3 5b fb 48 81 c5 c0 05 00 00 e9 84 f7 RSP: 0018:ffffc9000463f568 EFLAGS: 00010086 RAX: 0000000000000000 RBX: 0000000000000001 RCX: 0000000000000000 RDX: ffff88801eb28000 RSI: ffffffff814c03b7 RDI: 0000000000000001 RBP: ffff8881443b7190 R08: 0000000000000001 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000001 R12: 0000000000000003 R13: ffff88802a77cb18 R14: 0000000000000003 R15: ffff888018262500 FS: 0000000000000000(0000) GS:ffff8880b9800000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000556a99c15a18 CR3: 0000000028c71000 CR4: 0000000000350ef0 Call Trace: usbnet_start_xmit+0xfe5/0x2190 drivers/net/usb/usbnet.c:1453 __netdev_start_xmit include/linux/netdevice.h:4918 [inline] netdev_start_xmit include/linux/netdevice.h:4932 [inline] xmit_one net/core/dev.c:3578 [inline] dev_hard_start_xmit+0x187/0x700 net/core/dev.c:3594 ... This bug is caused by the fact that usbnet trusts the bulk endpoint addresses its probe routine receives in the driver_info structure, and it does not check to see that these endpoints actually exist and have the expected type and directions. The fix is simply to add such a check. Reported-and-tested-by: syzbot+63ee658b9a100ffadbe2@syzkaller.appspotmail.com Closes: https://lore.kernel.org/linux-usb/000000000000a56e9105d0cec021@google.com/ Signed-off-by: Alan Stern CC: Oliver Neukum Link: https://lore.kernel.org/r/ea152b6d-44df-4f8a-95c6-4db51143dcc1@rowland.harvard.edu Signed-off-by: Jakub Kicinski Signed-off-by: Greg Kroah-Hartman

USB: zaurus: Add ID for A-300/B-500/C-700

2023-08-11T09:33:56+00:00

commit b99225b4fe297d07400f9e2332ecd7347b224f8d upstream. The SL-A300, B500/5600, and C700 devices no longer auto-load because of "usbnet: Remove over-broad module alias from zaurus." This patch adds IDs for those 3 devices. Link: https://bugzilla.kernel.org/show_bug.cgi?id=217632 Fixes: 16adf5d07987 ("usbnet: Remove over-broad module alias from zaurus.") Signed-off-by: Ross Maynard Cc: stable@vger.kernel.org Acked-by: Greg Kroah-Hartman Reviewed-by: Andrew Lunn Link: https://lore.kernel.org/r/69b5423b-2013-9fc9-9569-58e707d9bafb@bigpond.com Signed-off-by: Jakub Kicinski Signed-off-by: Greg Kroah-Hartman

net: usb: qmi_wwan: add support for Compal RXM-G1

2023-06-21T13:38:58+00:00

commit 863199199713908afaa47ba09332b87621c12496 upstream. Add support for Compal RXM-G1 which is based on Qualcomm SDX55 chip. This patch adds support for two compositions: 0x9091: DIAG + MODEM + QMI_RMNET + ADB 0x90db: DIAG + DUN + RMNET + DPL + QDSS(Trace) + ADB T: Bus=03 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=5000 MxCh= 0 D: Ver= 3.20 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 9 #Cfgs= 1 P: Vendor=05c6 ProdID=9091 Rev= 4.14 S: Manufacturer=QCOM S: Product=SDXPRAIRIE-MTP _SN:719AB680 S: SerialNumber=719ab680 C:* #Ifs= 4 Cfg#= 1 Atr=80 MxPwr=896mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=(none) E: Ad=81(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none) E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=82(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan E: Ad=84(I) Atr=03(Int.) MxPS= 8 Ivl=32ms E: Ad=8e(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms E: Ad=0f(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none) E: Ad=03(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms E: Ad=85(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms T: Bus=03 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=5000 MxCh= 0 D: Ver= 3.20 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 9 #Cfgs= 1 P: Vendor=05c6 ProdID=90db Rev= 4.14 S: Manufacturer=QCOM S: Product=SDXPRAIRIE-MTP _SN:719AB680 S: SerialNumber=719ab680 C:* #Ifs= 6 Cfg#= 1 Atr=80 MxPwr=896mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=(none) E: Ad=81(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none) E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=82(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan E: Ad=84(I) Atr=03(Int.) MxPS= 8 Ivl=32ms E: Ad=8e(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms E: Ad=0f(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms I:* If#= 3 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=8f(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms I:* If#= 4 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=85(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms I:* If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none) E: Ad=03(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms E: Ad=86(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms Cc: stable@vger.kernel.org Signed-off-by: Wes Huang Acked-by: Bjørn Mork Link: https://lore.kernel.org/r/20230608030141.3546-1-wes.huang@moxa.com Signed-off-by: Jakub Kicinski Signed-off-by: Greg Kroah-Hartman