kernel/git/stable/linux.git/drivers/power, branch linux-5.16.y

power: supply: axp288-charger: Set Vhold to 4.4V

2022-04-13T18:03:02+00:00

[ Upstream commit 5ac121b81b4051e7fc83d5b3456a5e499d5bd147 ] The AXP288's recommended and factory default Vhold value (minimum input voltage below which the input current draw will be reduced) is 4.4V. This lines up with other charger IC's such as the TI bq2419x/bq2429x series which use 4.36V or 4.44V. For some reason some BIOS-es initialize Vhold to 4.6V or even 4.7V which combined with the typical voltage drop over typically low wire gauge micro-USB cables leads to the input-current getting capped below 1A (with a 2A capable dedicated charger) based on Vhold. This leads to slow charging, or even to the device slowly discharging if the device is in heavy use. As the Linux AXP288 drivers use the builtin BC1.2 charger detection and send the input-current-limit according to the detected charger there really is no reason not to use the recommended 4.4V Vhold. Set Vhold to 4.4V to fix the slow charging issue on various devices. There is one exception, the special-case of the HP X2 2-in-1s which combine this BC1.2 capable PMIC with a Type-C port and a 5V/3A factory provided charger with a Type-C plug which does not do BC1.2. These have their input-current-limit hardcoded to 3A (like under Windows) and use a higher Vhold on purpose to limit the current when used with other chargers. To avoid touching Vhold on these HP X2 laptops the code setting Vhold is added to an else branch of the if checking for these models. Note this also fixes the sofar unused VBUS_ISPOUT_VHOLD_SET_MASK define, which was wrong. Signed-off-by: Hans de Goede Signed-off-by: Sebastian Reichel Signed-off-by: Sasha Levin

power: supply: axp20x_battery: properly report current when discharging

2022-04-13T18:02:59+00:00

[ Upstream commit d4f408cdcd26921c1268cb8dcbe8ffb6faf837f3 ] As stated in [1], negative current values are used for discharging batteries. AXP PMICs internally have two different ADC channels for shunt current measurement: one used during charging and one during discharging. The values reported by these ADCs are unsigned. While the driver properly selects ADC channel to get the data from, it doesn't apply negative sign when reporting discharging current. [1] Documentation/ABI/testing/sysfs-class-power Signed-off-by: Evgeny Boger Acked-by: Chen-Yu Tsai Signed-off-by: Sebastian Reichel Signed-off-by: Sasha Levin

power: ab8500_chargalg: Use CLOCK_MONOTONIC

2022-04-08T12:06:16+00:00

[ Upstream commit c22fca40522e2be8af168f3087d87d85e404ea72 ] The HRTimer in the AB8500 charging code is using CLOCK_REALTIME to set an alarm some hours forward in time +/- 5 min for a safety timer. I have observed that this will sometimes fire sporadically early when charging a battery with the result that charging stops. As CLOCK_REALTIME can be subject to adjustments of time from sources such as NTP, this cannot be trusted and will likely for example fire events if the clock is set forward some hours by say NTP. Use CLOCK_MONOTONIC as indicated in other instances and the problem goes away. Also initialize the timer to REL mode as this is what will be used later. Fixes: 257107ae6b9b ("ab8500-chargalg: Use hrtimer") Cc: Lee Jones Suggested-by: Matti Vaittinen Signed-off-by: Linus Walleij Reviewed-by: Matti Vaittinen Signed-off-by: Sebastian Reichel Signed-off-by: Sasha Levin

power: supply: wm8350-power: Add missing free in free_charger_irq

2022-04-08T12:06:13+00:00

[ Upstream commit 6dee930f6f6776d1e5a7edf542c6863b47d9f078 ] In free_charger_irq(), there is no free for 'WM8350_IRQ_CHG_FAST_RDY'. Therefore, it should be better to add it in order to avoid the memory leak. Fixes: 14431aa0c5a4 ("power_supply: Add support for WM8350 PMU") Signed-off-by: Jiasheng Jiang Acked-by: Charles Keepax Signed-off-by: Sebastian Reichel Signed-off-by: Sasha Levin

power: supply: wm8350-power: Handle error for wm8350_register_irq

2022-04-08T12:06:13+00:00

[ Upstream commit b0b14b5ba11bec56fad344a4a0b2e16449cc8b94 ] As the potential failure of the wm8350_register_irq(), it should be better to check it and return error if fails. Also, use 'free_' in order to avoid same code. Fixes: 14431aa0c5a4 ("power_supply: Add support for WM8350 PMU") Signed-off-by: Jiasheng Jiang Acked-by: Charles Keepax Signed-off-by: Sebastian Reichel Signed-off-by: Sasha Levin

power: supply: bq24190_charger: Fix bq24190_vbus_is_enabled() wrong false return

2022-04-08T12:06:11+00:00

[ Upstream commit f7731754fdce33dad19be746f647d6ac47c5d695 ] The datasheet says that the BQ24190_REG_POC_CHG_CONFIG bits can have a value of either 10(0x2) or 11(0x3) for OTG (5V boost regulator) mode. Sofar bq24190_vbus_is_enabled() was only checking for 10 but some BIOS-es uses 11 when enabling the regulator at boot. Make bq24190_vbus_is_enabled() also check for 11 so that it does not wrongly returns false when the bits are set to 11. Fixes: 66b6bef2c4e0 ("power: supply: bq24190_charger: Export 5V boost converter as regulator") Cc: Bastien Nocera Signed-off-by: Hans de Goede Reviewed-by: Andy Shevchenko Signed-off-by: Sebastian Reichel Signed-off-by: Sasha Levin

power: supply: sbs-charger: Don't cancel work that is not initialized

2022-04-08T12:06:11+00:00

[ Upstream commit de85193cff0d94d030a53656d8fcc41794807bef ] This driver can use an interrupt or polling in order get the charger's status. When using polling, a delayed work is used. However, the remove() function unconditionally call cancel_delayed_work_sync(), even if the delayed work is not used and is not initialized. In order to fix it, use devm_delayed_work_autocancel() and remove the now useless remove() function. Fixes: feb583e37f8a ("power: supply: add sbs-charger driver") Signed-off-by: Christophe JAILLET Signed-off-by: Sebastian Reichel Signed-off-by: Sasha Levin

power: supply: ab8500: Fix memory leak in ab8500_fg_sysfs_init

2022-04-08T12:06:06+00:00

[ Upstream commit 6a4760463dbc6b603690938c468839985189ce0a ] kobject_init_and_add() takes reference even when it fails. According to the doc of kobject_init_and_add()： If this function returns an error, kobject_put() must be called to properly clean up the memory associated with the object. Fix memory leak by calling kobject_put(). Fixes: 8c0984e5a753 ("power: move power supply drivers to power/supply") Signed-off-by: Miaoqian Lin Signed-off-by: Sebastian Reichel Signed-off-by: Sasha Levin

power: reset: gemini-poweroff: Fix IRQ check in gemini_poweroff_probe

2022-04-08T12:06:01+00:00

[ Upstream commit ba18dad0fb880cd29aa97b6b75560ef14d1061ba ] platform_get_irq() returns negative error number instead 0 on failure. And the doc of platform_get_irq() provides a usage example: int irq = platform_get_irq(pdev, 0); if (irq < 0) return irq; Fix the check of return value to catch errors correctly. Fixes: f7a388d6cd1c ("power: reset: Add a driver for the Gemini poweroff") Signed-off-by: Miaoqian Lin Reviewed-by: Linus Walleij Signed-off-by: Sebastian Reichel Signed-off-by: Sasha Levin

power: reset: mt6397: Check for null res pointer

2022-01-27T11:01:54+00:00

[ Upstream commit 1c1348bf056dee665760a3bd1cd30b0be7554fc2 ] The return value of platform_get_resource() needs to be checked. To avoid use of error pointer in case that there is no suitable resource. Fixes: d28c74c10751 ("power: reset: add driver for mt6323 poweroff") Signed-off-by: Jiasheng Jiang Signed-off-by: Sebastian Reichel Signed-off-by: Sasha Levin