kernel/git/stable/linux.git/drivers/s390/net, branch linux-5.5.y

s390/qeth: handle error when backing RX buffer

2020-03-18T06:19:06+00:00

[ Upstream commit 17413852804d7e86e6f0576cca32c1541817800e ] qeth_init_qdio_queues() fills the RX ring with an initial set of RX buffers. If qeth_init_input_buffer() fails to back one of the RX buffers with memory, we need to bail out and report the error. Fixes: 4a71df50047f ("qeth: new qeth device driver") Signed-off-by: Julian Wiedmann Signed-off-by: David S. Miller Signed-off-by: Greg Kroah-Hartman

s390/qeth: don't reset default_out_queue

2020-03-18T06:19:05+00:00

[ Upstream commit 240c1948491b81cfe40f84ea040a8f2a4966f101 ] When an OSA device in prio-queue setup is reduced to 1 TX queue due to HW restrictions, we reset its the default_out_queue to 0. In the old code this was needed so that qeth_get_priority_queue() gets the queue selection right. But with proper multiqueue support we already reduced dev->real_num_tx_queues to 1, and so the stack puts all traffic on txq 0 without even calling .ndo_select_queue. Thus we can preserve the user's configuration, and apply it if the OSA device later re-gains support for multiple TX queues. Fixes: 73dc2daf110f ("s390/qeth: add TX multiqueue support for OSA devices") Signed-off-by: Julian Wiedmann Signed-off-by: David S. Miller Signed-off-by: Greg Kroah-Hartman

s390/qdio: fill SL with absolute addresses

2020-03-12T06:18:27+00:00

[ Upstream commit e9091ffd6a0aaced111b5d6ead5eaab5cd7101bc ] As the comment says, sl->sbal holds an absolute address. qeth currently solves this through wild casting, while zfcp doesn't care. Handle this properly in the code that actually builds the SL. Signed-off-by: Julian Wiedmann Reviewed-by: Alexandra Winter Reviewed-by: Steffen Maier [for qdio] Reviewed-by: Benjamin Block Signed-off-by: Vasily Gorbik Signed-off-by: Sasha Levin

s390/qeth: fix off-by-one in RX copybreak check

2020-03-05T15:45:19+00:00

commit 54a61fbc020fd2e305680871c453abcf7fc0339b upstream. The RX copybreak is intended as the _max_ value where the frame's data should be copied. So for frame_len == copybreak, don't build an SG skb. Fixes: 4a71df50047f ("qeth: new qeth device driver") Signed-off-by: Julian Wiedmann Signed-off-by: David S. Miller Signed-off-by: Greg Kroah-Hartman

s390/qeth: vnicc Fix EOPNOTSUPP precedence

2020-03-05T15:45:19+00:00

commit 6f3846f0955308b6d1b219419da42b8de2c08845 upstream. When getting or setting VNICC parameters, the error code EOPNOTSUPP should have precedence over EBUSY. EBUSY is used because vnicc feature and bridgeport feature are mutually exclusive, which is a temporary condition. Whereas EOPNOTSUPP indicates that the HW does not support all or parts of the vnicc feature. This issue causes the vnicc sysfs params to show 'blocked by bridgeport' for HW that does not support VNICC at all. Fixes: caa1f0b10d18 ("s390/qeth: add VNICC enable/disable support") Signed-off-by: Alexandra Winter Signed-off-by: Julian Wiedmann Signed-off-by: David S. Miller Signed-off-by: Greg Kroah-Hartman

s390/qeth: fix initialization on old HW

2019-12-25T06:41:06+00:00

I stumbled over an old OSA model that claims to support DIAG_ASSIST, but then rejects the cmd to query its DIAG capabilities. In the old code this was ok, as the returned raw error code was > 0. Now that we translate the raw codes to errnos, the "rc < 0" causes us to fail the initialization of the device. The fix is trivial: don't bail out when the DIAG query fails. Such an error is not critical, we can still use the device (with a slightly reduced set of features). Fixes: 742d4d40831d ("s390/qeth: convert remaining legacy cmd callbacks") Signed-off-by: Julian Wiedmann Signed-off-by: David S. Miller

s390/qeth: vnicc Fix init to default

2019-12-25T06:41:06+00:00

During vnicc_init wanted_char should be compared to cur_char and not to QETH_VNICC_DEFAULT. Without this patch there is no way to enforce the default values as desired values. Note, that it is expected, that a card comes online with default values. This patch was tested with private card firmware. Fixes: caa1f0b10d18 ("s390/qeth: add VNICC enable/disable support") Signed-off-by: Alexandra Winter Signed-off-by: Julian Wiedmann Signed-off-by: David S. Miller

s390/qeth: Fix vnicc_is_in_use if rx_bcast not set

2019-12-25T06:41:06+00:00

Symptom: After vnicc/rx_bcast has been manually set to 0, bridge_* sysfs parameters can still be set or written. Only occurs on HiperSockets, as OSA doesn't support changing rx_bcast. Vnic characteristics and bridgeport settings are mutually exclusive. rx_bcast defaults to 1, so manually setting it to 0 should disable bridge_* parameters. Instead it makes sense here to check the supported mask. If the card does not support vnicc at all, bridge commands are always allowed. Fixes: caa1f0b10d18 ("s390/qeth: add VNICC enable/disable support") Signed-off-by: Alexandra Winter Signed-off-by: Julian Wiedmann Signed-off-by: David S. Miller

s390/qeth: fix false reporting of VNIC CHAR config failure

2019-12-25T06:41:06+00:00

Symptom: Error message "Configuring the VNIC characteristics failed" in dmesg whenever an OSA interface on z15 is set online. The VNIC characteristics get re-programmed when setting a L2 device online. This follows the selected 'wanted' characteristics - with the exception that the INVISIBLE characteristic unconditionally gets switched off. For devices that don't support INVISIBLE (ie. OSA), the resulting IO failure raises a noisy error message ("Configuring the VNIC characteristics failed"). For IQD, INVISIBLE is off by default anyways. So don't unnecessarily special-case the INVISIBLE characteristic, and thereby suppress the misleading error message on OSA devices. Fixes: caa1f0b10d18 ("s390/qeth: add VNICC enable/disable support") Signed-off-by: Alexandra Winter Reviewed-by: Julian Wiedmann Signed-off-by: Julian Wiedmann Signed-off-by: David S. Miller

s390/qeth: lock the card while changing its hsuid

2019-12-25T06:41:06+00:00

qeth_l3_dev_hsuid_store() initially checks the card state, but doesn't take the conf_mutex to ensure that the card stays in this state while being reconfigured. Rework the code to take this lock, and drop a redundant state check in a helper function. Fixes: b333293058aa ("qeth: add support for af_iucv HiperSockets transport") Signed-off-by: Julian Wiedmann Signed-off-by: David S. Miller