kernel/git/stable/linux.git/drivers/usb/host, branch linux-4.17.y

usb: xhci: dbc: Don't decrement runtime PM counter if DBC is not started

2018-08-24T11:06:56+00:00

[ Upstream commit 74cb319bd97dd62881f97ea5a3228f7c2546bf56 ] pm_runtime_put_sync() gets called everytime in xhci_dbc_stop(). If dbc is not started, this makes the runtime PM counter incorrectly becomes 0, and calls autosuspend function. Then we'll keep seeing this: [54664.762220] xhci_hcd 0000:00:14.0: Root hub is not suspended So only calls pm_runtime_put_sync() when dbc was started. Signed-off-by: Kai-Heng Feng Signed-off-by: Mathias Nyman Signed-off-by: Greg Kroah-Hartman Signed-off-by: Sasha Levin Signed-off-by: Greg Kroah-Hartman

usb: xhci: increase CRS timeout value

2018-08-24T11:06:49+00:00

[ Upstream commit 305886ca87be480ae159908c2affd135c04215cf ] Some controllers take almost 55ms to complete controller restore state (CRS). There is no timeout limit mentioned in xhci specification so fixing the issue by increasing the timeout limit to 100ms [reformat code comment -Mathias] Signed-off-by: Ajay Gupta Signed-off-by: Nagaraj Annaiah Signed-off-by: Mathias Nyman Signed-off-by: Greg Kroah-Hartman Signed-off-by: Sasha Levin Signed-off-by: Greg Kroah-Hartman

usb: xhci: remove the code build warning

2018-08-24T11:06:49+00:00

[ Upstream commit 36eb93509c45d0bdbd8d09a01ab9d857972f5963 ] Initialize the 'err' variate to remove the build warning, the warning is shown as below: drivers/usb/host/xhci-tegra.c: In function 'tegra_xusb_mbox_thread': drivers/usb/host/xhci-tegra.c:552:6: warning: 'err' may be used uninitialized in this function [-Wuninitialized] drivers/usb/host/xhci-tegra.c:482:6: note: 'err' was declared here Fixes: e84fce0f8837 ("usb: xhci: Add NVIDIA Tegra XUSB controller driver") Signed-off-by: Dongjiu Geng Acked-by: Thierry Reding Acked-by: Jon Hunter Signed-off-by: Mathias Nyman Signed-off-by: Greg Kroah-Hartman Signed-off-by: Sasha Levin Signed-off-by: Greg Kroah-Hartman

usb: xhci: Fix memory leak in xhci_endpoint_reset()

2018-07-28T05:57:17+00:00

commit d89b7664f76047e7beca8f07e86f2ccfad085a28 upstream. If td_list is not empty the cfg_cmd will not be freed, call xhci_free_command to free it. Signed-off-by: Zheng Xiaowei Cc: Signed-off-by: Mathias Nyman Signed-off-by: Greg Kroah-Hartman

xhci: Fix perceived dead host due to runtime suspend race with event handler

2018-07-25T09:26:13+00:00

commit 229bc19fd7aca4f37964af06e3583c1c8f36b5d6 upstream. Don't rely on event interrupt (EINT) bit alone to detect pending port change in resume. If no change event is detected the host may be suspended again, oterwise roothubs are resumed. There is a lag in xHC setting EINT. If we don't notice the pending change in resume, and the controller is runtime suspeded again, it causes the event handler to assume host is dead as it will fail to read xHC registers once PCI puts the controller to D3 state. [ 268.520969] xhci_hcd: xhci_resume: starting port polling. [ 268.520985] xhci_hcd: xhci_hub_status_data: stopping port polling. [ 268.521030] xhci_hcd: xhci_suspend: stopping port polling. [ 268.521040] xhci_hcd: // Setting command ring address to 0x349bd001 [ 268.521139] xhci_hcd: Port Status Change Event for port 3 [ 268.521149] xhci_hcd: resume root hub [ 268.521163] xhci_hcd: port resume event for port 3 [ 268.521168] xhci_hcd: xHC is not running. [ 268.521174] xhci_hcd: handle_port_status: starting port polling. [ 268.596322] xhci_hcd: xhci_hc_died: xHCI host controller not responding, assume dead The EINT lag is described in a additional note in xhci specs 4.19.2: "Due to internal xHC scheduling and system delays, there will be a lag between a change bit being set and the Port Status Change Event that it generated being written to the Event Ring. If SW reads the PORTSC and sees a change bit set, there is no guarantee that the corresponding Port Status Change Event has already been written into the Event Ring." Cc: Signed-off-by: Mathias Nyman Signed-off-by: Kai-Heng Feng Signed-off-by: Greg Kroah-Hartman

xhci: xhci-mem: off by one in xhci_stream_id_to_ring()

2018-07-17T09:48:28+00:00

commit 313db3d6488bb03b61b99de9dbca061f1fd838e1 upstream. The > should be >= here so that we don't read one element beyond the end of the ep->stream_info->stream_rings[] array. Fixes: e9df17eb1408 ("USB: xhci: Correct assumptions about number of rings per endpoint.") Signed-off-by: Dan Carpenter Cc: stable Signed-off-by: Greg Kroah-Hartman

xhci: Fix kernel oops in trace_xhci_free_virt_device

2018-07-08T13:32:17+00:00

commit d850c1658328e757635a46763783c6fd56390dcb upstream. commit 44a182b9d177 ("xhci: Fix use-after-free in xhci_free_virt_device") set dev->udev pointer to NULL in xhci_free_dev(), it will cause kernel panic in trace_xhci_free_virt_device. This patch reimplement the trace function trace_xhci_free_virt_device, remove dev->udev dereference and added more useful parameters to show in the trace function,it also makes sure dev->udev is not NULL before calling trace_xhci_free_virt_device. This issue happened when xhci-hcd trace is enabled and USB devices hot plug test. Original use-after-free patch went to stable so this needs so be applied there as well. [ 1092.022457] usb 2-4: USB disconnect, device number 6 [ 1092.092772] BUG: unable to handle kernel NULL pointer dereference at 0000000000000000 [ 1092.101694] PGD 0 P4D 0 [ 1092.104601] Oops: 0000 [#1] SMP [ 1092.207734] Workqueue: usb_hub_wq hub_event [ 1092.212507] RIP: 0010:trace_event_raw_event_xhci_log_virt_dev+0x6c/0xf0 [ 1092.220050] RSP: 0018:ffff8c252e883d28 EFLAGS: 00010086 [ 1092.226024] RAX: ffff8c24af86fa84 RBX: 0000000000000003 RCX: ffff8c25255c2a01 [ 1092.234130] RDX: 0000000000000000 RSI: 00000000aef55009 RDI: ffff8c252e883d28 [ 1092.242242] RBP: ffff8c252550e2c0 R08: ffff8c24af86fa84 R09: 0000000000000a70 [ 1092.250364] R10: 0000000000000a70 R11: 0000000000000000 R12: ffff8c251f21a000 [ 1092.258468] R13: 000000000000000c R14: ffff8c251f21a000 R15: ffff8c251f432f60 [ 1092.266572] FS: 0000000000000000(0000) GS:ffff8c252e880000(0000) knlGS:0000000000000000 [ 1092.275757] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 1092.282281] CR2: 0000000000000000 CR3: 0000000154209001 CR4: 00000000003606e0 [ 1092.290384] Call Trace: [ 1092.293156] [ 1092.295439] xhci_free_virt_device.part.34+0x182/0x1a0 [ 1092.301288] handle_cmd_completion+0x7ac/0xfa0 [ 1092.306336] ? trace_event_raw_event_xhci_log_trb+0x6e/0xa0 [ 1092.312661] xhci_irq+0x3e8/0x1f60 [ 1092.316524] __handle_irq_event_percpu+0x75/0x180 [ 1092.321876] handle_irq_event_percpu+0x20/0x50 [ 1092.326922] handle_irq_event+0x36/0x60 [ 1092.331273] handle_edge_irq+0x6d/0x180 [ 1092.335644] handle_irq+0x16/0x20 [ 1092.339417] do_IRQ+0x41/0xc0 [ 1092.342782] common_interrupt+0xf/0xf [ 1092.346955] Fixes: 44a182b9d177 ("xhci: Fix use-after-free in xhci_free_virt_device") Cc: Signed-off-by: Zhengjun Xing Signed-off-by: Mathias Nyman Signed-off-by: Greg Kroah-Hartman

xhci: Fix USB3 NULL pointer dereference at logical disconnect.

2018-05-14T09:05:53+00:00

Hub driver will try to disable a USB3 device twice at logical disconnect, racing with xhci_free_dev() callback from the first port disable. This can be triggered with "udisksctl power-off --block-device " or by writing "1" to the "remove" sysfs file for a USB3 device in 4.17-rc4. USB3 devices don't have a similar disabled link state as USB2 devices, and use a U3 suspended link state instead. In this state the port is still enabled and connected. hub_port_connect() first disconnects the device, then later it notices that device is still enabled (due to U3 states) it will try to disable the port again (set to U3). The xhci_free_dev() called during device disable is async, so checking for existing xhci->devs[i] when setting link state to U3 the second time was successful, even if device was being freed. The regression was caused by, and whole thing revealed by, Commit 44a182b9d177 ("xhci: Fix use-after-free in xhci_free_virt_device") which sets xhci->devs[i]->udev to NULL before xhci_virt_dev() returned. and causes a NULL pointer dereference the second time we try to set U3. Fix this by checking xhci->devs[i]->udev exists before setting link state. The original patch went to stable so this fix needs to be applied there as well. Fixes: 44a182b9d177 ("xhci: Fix use-after-free in xhci_free_virt_device") Cc: Reported-by: Jordan Glover Tested-by: Jordan Glover Signed-off-by: Mathias Nyman Signed-off-by: Greg Kroah-Hartman

Revert "usb: host: ehci: Use dma_pool_zalloc()"

2018-05-04T21:35:12+00:00

This reverts commit 22072e83ebd510fb6a090aef9d65ccfda9b1e7e4 as it is broken. Alan writes: What you can't see just from reading the patch is that in both cases (ehci->itd_pool and ehci->sitd_pool) there are two allocation paths -- the two branches of an "if" statement -- and only one of the paths calls dma_pool_[z]alloc. However, the memset is needed for both paths, and so it can't be eliminated. Given that it must be present, there's no advantage to calling dma_pool_zalloc rather than dma_pool_alloc. Reported-by: Erick Cafferata Cc: Alan Stern Cc: Souptick Joarder Signed-off-by: Greg Kroah-Hartman

xhci: Fix use-after-free in xhci_free_virt_device

2018-05-03T15:55:32+00:00

KASAN found a use-after-free in xhci_free_virt_device+0x33b/0x38e where xhci_free_virt_device() sets slot id to 0 if udev exists: if (dev->udev && dev->udev->slot_id) dev->udev->slot_id = 0; dev->udev will be true even if udev is freed because dev->udev is not set to NULL. set dev->udev pointer to NULL in xhci_free_dev() The original patch went to stable so this fix needs to be applied there as well. Fixes: a400efe455f7 ("xhci: zero usb device slot_id member when disabling and freeing a xhci slot") Cc: Reported-by: Guenter Roeck Reviewed-by: Guenter Roeck Tested-by: Guenter Roeck Signed-off-by: Mathias Nyman Signed-off-by: Greg Kroah-Hartman