kernel/git/stable/linux.git/include/asm-arm/arch-at91/board.h, branch master

[ARM] Move include/asm-arm/arch-* to arch/arm/*/include/mach

2008-08-07T08:55:48+00:00

This just leaves include/asm-arm/plat-* to deal with. Signed-off-by: Russell King

Merge branch 'linux-next' of git://git.infradead.org/~dedekind/ubi-2.6

2008-07-25T14:40:14+00:00

[ARM] 5130/4: Support for the at91sam9g20

2008-07-10T11:13:47+00:00

Support for the at91sam9g20 : Atmel 400Mhz ARM 926ej-s SOC. AT91sam9g20 is an evolution of the at91sam9260 with a faster clock speed. We created a new board for this device but based the chip support directly on 9260 files with little updates. Here is the chip page on Atmel wabsite: http://atmel.com/dyn/products/product_card.asp?part_id=4337 Signed-off-by: Sedji Gaouaou Signed-off-by: Justin Waters Acked-by: Andrew Victor Signed-off-by: Russell King

[MTD] [NAND] rename at91_nand -> atmel_nand: internal symbols

2008-06-07T07:43:00+00:00

This is basically s/at91_nand/atmel_nand/g with some manual inspection. Signed-off-by: Håvard Skinnemoen Signed-off-by: David Woodhouse

[ARM] 4933/1: AT91CAP9 UDPHS driver: generic AT91 parts.

2008-06-02T14:08:07+00:00

This is patch 1 of 2 adding support for the USB High Speed Device Port on the AT91CAP9 system on chip. The AT91CAP9 uses the same UDPHS IP as the AVR32 and the AT91SAM9RL. This patch makes the generic AT91 adaptations, mainly dealing with the addition of the UDPHS UTMI clock. Signed-off-by: Stelian Pop Acked-by: Haavard Skinnemoen Acked-by: Andrew Victor Signed-off-by: Russell King

USB: at91_udc uses generic GPIO calls; minor cleanup

2008-02-01T22:35:01+00:00

Various small at91_udc cleanups: - Use generic GPIO calls, not older platform-specific ones - Use gpio_request()/gpio_free() - Use VERBOSE_DEBUG convention, not older VERBOSE - Fix sparse complaint about parameter type (changed to gfp_t) - Add missing newline to some rarely-seen debug messages - Fix some old cleanup bugs on probe() fault paths Also add a mechanism whereby rm9200 gpios can drive the D+ pullup through an inverting transistor, based on a patch from Steve Birtles. Most UDC drivers supporting a GPIO based pullup should probably have such an option, but testing it requries such a board in hand! Signed-off-by: David Brownell Cc: Steve Birtles Signed-off-by: Greg Kroah-Hartman

[ARM] 4764/1: [AT91] AT91CAP9 core support

2008-01-26T15:01:13+00:00

Add support for Atmel's AT91CAP9 Customizable Microcontroller family. Signed-off-by: Stelian Pop Signed-off-by: Andrew Victor Signed-off-by: Russell King

[ARM] 4758/1: [AT91] LEDs

2008-01-26T15:00:32+00:00

Move the LED initialization code out of the various *_devices.c files, and into leds.c. Also add support for NEW_LEDs. Patch from David Brownell. Signed-off-by: Andrew Victor Signed-off-by: Russell King

[ARM] 4757/1: [AT91] UART initialization

2008-01-26T15:00:32+00:00

Modify the UART initialization to allow the board-initialization code to specify which pins are connected, and which pins should therefore be initialized. The current at91_init_serial() will continue to work as-is, but is marked as "deprecated" and will be removed once the board-specific files has been updated to use the new interface. As in the AVR32 code, we assume that the TX and RX pins will always be initialized. Signed-off-by: Andrew Victor Signed-off-by: Russell King

[ARM] 4754/1: [AT91] SSC library support

2008-01-26T15:00:31+00:00

Core support of the Atmel SSC library for all Atmel AT91 processors. Based on David Brownell's initial patch for the AT91RM9200. Signed-off-by: Andrew Victor Acked-by: David Brownell Signed-off-by: Russell King