kernel/git/stable/linux.git/include/asm-powerpc/machdep.h, branch master

powerpc: Move include files to arch/powerpc/include/asm

2008-08-04T02:02:00+00:00

from include/asm-powerpc. This is the result of a mkdir arch/powerpc/include/asm git mv include/asm-powerpc/* arch/powerpc/include/asm Followed by a few documentation/comment fixups and a couple of places where was being used explicitly. Of the latter only one was outside the arch code and it is a driver only built for powerpc. Signed-off-by: Stephen Rothwell Signed-off-by: Paul Mackerras

powerpc/pseries: iommu enablement for CMO

2008-07-25T05:44:43+00:00

To support Cooperative Memory Overcommitment (CMO), we need to check for failure from some of the tce hcalls. These changes for the pseries platform affect the powerpc architecture; patches for the other affected platforms are included in this patch. pSeries platform IOMMU code changes: * platform TCE functions must handle H_NOT_ENOUGH_RESOURCES errors and return an error. Architecture IOMMU code changes: * Calls to ppc_md.tce_build need to check return values and return DMA_MAPPING_ERROR for transient errors. Architecture changes: * struct machdep_calls for tce_build*_pSeriesLP functions need to change to indicate failure. * all other platforms will need updates to iommu functions to match the new calling semantics; they will return 0 on success. The other platforms default configs have been built, but no further testing was performed. Signed-off-by: Robert Jennings Acked-by: Olof Johansson Acked-by: Paul Mackerras Signed-off-by: Benjamin Herrenschmidt

powerpc/dma: Use the struct dma_attrs in iommu code

2008-07-22T00:39:32+00:00

Update iommu_alloc() to take the struct dma_attrs and pass them on to tce_build(). This change propagates down to the tce_build functions of all the platforms. Signed-off-by: Mark Nelson Signed-off-by: Arnd Bergmann Signed-off-by: Benjamin Herrenschmidt

powerpc/85xx: add DOZE/NAP support for e500 core

2008-06-26T06:48:56+00:00

The e500 core enter DOZE/NAP power-saving modes when the core go to cpu_idle routine. The power management default running mode is DOZE, If the user echo 1 > /proc/sys/kernel/powersave-nap the system will change to NAP running mode. Signed-off-by: Dave Liu Signed-off-by: Kumar Gala

[POWERPC] Remove unused machine call outs

2008-04-17T00:01:00+00:00

When we moved to arch/powerpc we actively tried to avoid using the ppc_md.setup_io_mappings(). Currently no board ports use it so let's remove it to avoid any new boards using it. Also, remove early_serial_map() since we don't even have a call out for it in arch/powerpc. Signed-off-by: Kumar Gala Signed-off-by: Paul Mackerras

[POWERPC] Add code for removing HPTEs for parts of the linear mapping

2008-02-26T11:17:03+00:00

For memory remove, we need to clean up htab mappings for the section of the memory we are removing. This implements support for removing htab bolted mappings for pSeries logical partitions. Other sub-archs may need to implement similar functionality for hotplug memory remove to work on them. Signed-off-by: Badari Pulavarty Signed-off-by: Paul Mackerras

[POWERPC] Implement arch disable/enable irq hooks.

2007-12-21T11:13:35+00:00

These hooks ensure that a decrementer interrupt is not pending when suspending; otherwise, problems may occur on 6xx/7xx/7xxx-based systems (except for powermacs, which use a separate suspend path). For example, with deep sleep on the 831x, a pending decrementer will cause a system freeze because the SoC thinks the decrementer interrupt would have woken the system, but the core must have interrupts disabled due to the setup required for deep sleep. Changed via-pmu.c to use the new ppc_md hooks, and made the arch_* functions call the generic_* functions unconditionally. -- paulus Signed-off-by: Scott Wood Signed-off-by: Paul Mackerras

[POWERPC] Merge 32 and 64 bits pcibios_enable_device

2007-12-20T05:18:11+00:00

This merge the two implementations, based on the previously fixed up 32 bits one. The pcibios_enable_device_hook in ppc_md is now available for ppc64 use. Also remove the new unused "initial" parameter from it and fixup users. Signed-off-by: Benjamin Herrenschmidt Signed-off-by: Paul Mackerras

[POWERPC] Merge PCI resource fixups

2007-12-20T05:18:09+00:00

The PCI code in 32 and 64 bits fixes up resources differently. 32 bits uses a header quirk plus handles bridges in pcibios_fixup_bus() while 64 bits does things in various places depending on whether you are using OF probing, using PCI hotplug, etc... This merges those by basically using the 32 bits approach for both, with various tweaks to make 64 bits work with the new approach. Signed-off-by: Benjamin Herrenschmidt Signed-off-by: Paul Mackerras

[POWERPC] Add machine initcall macros

2007-12-20T05:11:46+00:00

The machine initcall macros allow initcalls to be registered which test machine_is() before executing the initcall. Signed-off-by: Grant Likely Signed-off-by: Paul Mackerras