kernel/git/stable/linux.git/include/asm-sh/irq.h, branch master

sh: migrate to arch/sh/include/

2008-07-28T23:09:44+00:00

This follows the sparc changes a439fe51a1f8eb087c22dd24d69cebae4a3addac. Most of the moving about was done with Sam's directions at: http://marc.info/?l=linux-sh&m=121724823706062&w=2 with subsequent hacking and fixups entirely my fault. Signed-off-by: Sam Ravnborg Signed-off-by: Paul Mundt

sh: asm/irq.h needs asm/cpu/irq.h.

2008-02-14T05:22:12+00:00

The SH-5 build currently fails when trying to build the i8042 code due to the missing IRQ definitions. These are provided in asm/cpu/irq.h, so just include that there to get it building again. Signed-off-by: Paul Mundt

sh: Decouple 4k and soft/hardirq stacks.

2007-11-02T03:16:51+00:00

While using separate IRQ stacks can cut down on stack consumption, many users can also use 4k stacks directly without the additional need of separate stacks for soft and hardirqs. With this split, we support the same rationale for 4KSTACKS as m68knommu, with the IRQSTACKS abstraction as per ppc64. Signed-off-by: Paul Mundt

sh: rework ipr code

2007-06-15T09:56:19+00:00

This patch reworks the ipr code by grouping the offset array together with the ipr_data structure in a new data structure called ipr_desc. This new structure also contains the name of the controller in struct irq_chip. The idea behind putting struct irq_chip in there is that we can use offsetof() to locate the base addresses in the irq_chip callbacks. This strategy has much in common with the recently merged intc2 code. One logic change has been made - the original ipr code enabled the interrupts by default but with this patch they are all disabled by default. Signed-off-by: Magnus Damm Signed-off-by: Paul Mundt

sh: rework intc2 code

2007-06-15T01:41:54+00:00

The shared intc2 code currently contains cpu-specific #ifdefs. This is a tad unclean and it prevents us from using the shared code to drive board-specific irqs on the se7780 board. This patch reworks the intc2 code by moving the base addresses of the intc2 registers into struct intc2_desc. This new structure also contains the name of the controller in struct irq_chip. The idea behind putting struct irq_chip in there is that we can use offsetof() to locate the base addresses in the irq_chip callbacks. One logic change has been made - the original shared intc2 code enabled the interrupts by default but with this patch they are all disabled by default. Signed-off-by: Magnus Damm Signed-off-by: Paul Mundt

sh: NR_IRQS consolidation.

2007-05-07T02:10:53+00:00

Each board sets the total number of IRQs that it's interested in via the machvec. Previously we cared about the off vs on-chip IRQ range, but any code relying on that is long dead. Set NR_IRQS to something sensible given the vector range, and allow boards to cap it if they really care. Signed-off-by: Paul Mundt

sh: Fix bogus regs pointer in do_IRQ().

2007-03-14T04:03:35+00:00

SH-3 and SH-4 were trampling the register, and SH-2 wasn't even setting it in the first place. This ended up with some rather broken behaviour in the sysrq show_regs(). Signed-off-by: Paul Mundt

sh: Kill off dead bigsur and ec3104 boards.

2007-02-14T06:06:09+00:00

Neither of these have had any maintenance in years, and there's no interest in keeping them straggling along. These have already been slated for removal some time, so finally just get rid of them. Signed-off-by: Paul Mundt

sh: SH-MobileR SH7722 CPU support.

2006-12-11T23:42:09+00:00

This adds CPU support for the SH7722. Signed-off-by: Paul Mundt

sh: sh775x/titan fixes for irq header changes.

2006-12-06T03:05:02+00:00

The following moves the creation of IPR interupts into setup-7750.c and updates a few other things to make it all work after the "Drop CPU subtype IRQ headers" commit. It boots and runs fine on my titan board. - adds an ipr_idx to the ipr_data and uses a function in the subtype code to calculate the address of the IPR registers - adds a function to enable individual interrupt mode for externals in the subtype code and calls that from the titan board code instead of doing it directly. - I changed the shift in the ipr_data to be the actual # of bits to shift, instead of the numnber / 4 - made it easier to match with the manual. Signed-off-by: Jamie Lenehan Signed-off-by: Paul Mundt