kernel/git/stable/linux.git/include/dt-bindings/pinctrl, branch linux-3.18.y

ARM: dts: Fix omap3 off mode pull defines

2017-11-21T08:01:04+00:00

[ Upstream commit d97556c8012015901a3ce77f46960078139cd79d ] We need to also have OFFPULLUDENABLE bit set to use the off mode pull values. Otherwise the line is pulled down internally if no external pull exists. This is has some documentation at: http://processors.wiki.ti.com/index.php/Optimizing_OMAP35x_and_AM/DM37x_OFF_mode_PAD_configuration Note that the value is still glitchy during off mode transitions as documented in spz319f.pdf "Advisory 1.45". It's best to use external pulls instead of relying on the internal ones for off mode and even then anything pulled up will get driven down momentarily on off mode restore for GPIO banks other than bank1. Signed-off-by: Tony Lindgren Signed-off-by: Sasha Levin Signed-off-by: Greg Kroah-Hartman

pinctrl: dra: dt-bindings: Fix output pull up/down

2014-11-10T22:29:20+00:00

For PIN_OUTPUT_PULLUP and PIN_OUTPUT_PULLDOWN we must not set the PULL_DIS bit which disables the PULLs. PULL_ENA is a 0 and using it in an OR operation is a NOP, so don't use it in the PIN_OUTPUT_PULLUP/DOWN macros. Fixes: 23d9cec07c58 ("pinctrl: dra: dt-bindings: Fix pull enable/disable") Signed-off-by: Roger Quadros Acked-by: Nishanth Menon Signed-off-by: Tony Lindgren

pinctrl: at91: add drive strength configuration

2014-09-05T08:32:06+00:00

The SAMA5 and SAM9x5 series both have drive strength options for the PIOs. This patch adds the ability to set one of three hardware options for drive strengths of low, medium or high for the each pin. The actual current output of the chip based on the setting is defined in the datasheets and varies per pins separate from banks and with supply voltage. This patch adds three new dt-bindings that allow setting the strength when configuring pins. By default, no change will be made to the drive strength of a pin from its reset value. Due to the difference between the register addresses of the SAMA5 and SAM9x5 series, a new sama5d3-pinctrl id was added. Signed-off-by: Marek Roszko Acked-by: Nicolas Ferre Signed-off-by: Linus Walleij

pinctrl: Add mux options 3 and 4 for rockchip pinctrl

2014-08-28T13:18:03+00:00

Newer Rockchip SoCs have more muxing slots. Add slots 3 and 4 since the rk3288 table goes all the way up to 4. Signed-off-by: Doug Anderson Reviewed-by: Heiko Stuebner Signed-off-by: Linus Walleij

Merge tag 'dt-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

2014-08-08T18:16:58+00:00

Pull ARM SoC device-tree changes from Olof Johansson: "Unlike the board branch, this keeps having large sets of changes for every release, but that's quite expected and is so far working well. Most of this is plumbing for various device bindings and new platforms, but there's also a bit of cleanup and code removal for things that are moved from platform code to DT contents (some OMAP clock code in particular). There's also a pinctrl driver for tegra here (appropriately acked), that's introduced this way to make it more bisectable. I'm happy to say that there were no conflicts at all with this branch this release, which means that changes are flowing through our tree as expected instead of merged through driver maintainers (or at least not done with conflicts). There are several new boards added, and a couple of SoCs. In no particular order: - Rockchip RK3288 SoC support, including DTS for a dev board that they have seeded with some community developers. - Better support for Hardkernel Exynos4-based ODROID boards. - CCF conversions (and dtsi contents) for several Renesas platforms. - Gumstix Pepper (TI AM335x) board support - TI eval board support for AM437x - Allwinner A23 SoC, very similar to existing ones which mostly has resulted in DT changes for support. Also includes support for an Ippo tablet with the chipset. - Allwinner A31 Hummingbird board support, not to be confused with the SolidRun i.MX-based Hummingboard. - Tegra30 Apalis board support" * tag 'dt-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (334 commits) ARM: dts: Enable USB host0 (EHCI) on rk3288-evb ARM: dts: add rk3288 ehci usb devices ARM: dts: Turn on USB host vbus on rk3288-evb ARM: tegra: apalis t30: fix device tree compatible node ARM: tegra: paz00: Fix some indentation inconsistencies ARM: zynq: DT: Clarify Xilinx Zynq platform ARM: dts: rockchip: add watchdog node ARM: dts: rockchip: remove pinctrl setting from radxarock uart2 ARM: dts: Add missing pinctrl for uart0/1 for exynos3250 ARM: dts: Remove duplicate 'interrput-parent' property for exynos3250 ARM: dts: Add TMU dt node to monitor the temperature for exynos3250 ARM: dts: Specify MAX77686 pmic interrupt for exynos5250-smdk5250 ARM: dts: cypress,cyapa trackpad is exynos5250-Snow only ARM: dts: max77686 is exynos5250-snow only ARM: zynq: DT: Remove DMA from board DTs ARM: zynq: DT: Add CAN node ARM: EXYNOS: Add exynos5260 PMU compatible string to DT match table ARM: dts: Add PMU DT node for exynos5260 SoC ARM: EXYNOS: Add support for Exynos5410 PMU ARM: dts: Add PMU to exynos5410 ...

pinctrl: dra: dt-bindings: Fix pull enable/disable

2014-07-23T08:44:50+00:00

The DRA74/72 control module pins have a weak pull up and pull down. This is configured by bit offset 17. if BIT(17) is 1, a pull up is selected, else a pull down is selected. However, this pull resisstor is applied based on BIT(16) - PULLUDENABLE - if BIT(18) is *0*, then pull as defined in BIT(17) is applied, else no weak pulls are applied. We defined this in reverse. Reference: Table 18-5 (Description of the pad configuration register bits) in Technical Reference Manual Revision (DRA74x revision Q: SPRUHI2Q Revised June 2014 and DRA72x revision F: SPRUHP2F - Revised June 2014) Fixes: 6e58b8f1daaf1a ("ARM: dts: DRA7: Add the dts files for dra7 SoC and dra7-evm board") Signed-off-by: Nishanth Menon Tested-by: Felipe Balbi Acked-by: Felipe Balbi Signed-off-by: Tony Lindgren

of: Add NVIDIA Tegra XUSB pad controller binding

2014-07-11T12:40:41+00:00

This patch adds the device tree binding documentation for the XUSB pad controller found on NVIDIA Tegra SoCs. It exposes both pinmuxing and PHY capabilities. Tested-by: Mikko Perttunen Acked-by: Linus Walleij Signed-off-by: Thierry Reding

Merge tag 'dt-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc into next

2014-06-02T23:34:00+00:00

Pull ARM SoC devicetree updates from Olof Johansson: "As with previous release, this continues to be among the largest branches we merge, with lots of new contents. New things for this release are among other things: - DTSI contents for the new SoCs supported in 3.16 (see SoC pull request) - Qualcomm APQ8064 and APQ8084 SoCs and eval boards - Nvidia Jetson TK1 development board (Tegra T124-based) Two new SoCs that didn't need enough new platform code to stand out enough for me to notice when writing the SoC tag, but that adds new DT contents are: - TI DRA72 - Marvell Berlin 2Q" * tag 'dt-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (500 commits) ARM: dts: add secure firmware support for exynos5420-arndale-octa ARM: dts: add pmu sysreg node to exynos3250 ARM: dts: correct the usb phy node in exynos5800-peach-pi ARM: dts: correct the usb phy node in exynos5420-peach-pit ARM: dts: add dts files for exynos5410 and exynos5410-smdk5410 ARM: dts: add dts files for exynos3250 SoC ARM: dts: add mfc node for exynos5800 ARM: dts: add Vbus regulator for USB 3.0 on exynos5800-peach-pi ARM: dts: enable fimd for exynos5800-peach-pi ARM: dts: enable display controller for exynos5800-peach-pi ARM: dts: enable hdmi for exynos5800-peach-pi ARM: dts: add dts file for exynos5800-peach-pi board ARM: dts: add dts file for exynos5800 SoC ARM: dts: add dts file for exynos5260-xyref5260 board ARM: dts: add dts files for exynos5260 SoC ARM: dts: update watchdog node name in exynos5440 ARM: dts: use key code macros on Origen and Arndale boards ARM: dts: enable RTC and WDT nodes on Origen boards ARM: dts: qcom: Add APQ8084-MTP board support ARM: dts: qcom: Add APQ8084 SoC support ...

ARM: dts: Change IOPAD macro's for OMAP4/5

2014-05-20T00:20:29+00:00

The OMAP4/5 TRMs primarily list address offsets from the padconf physical address (which is not driver base address) and not always the absolute physical address for padconf registers like some other OMAP TRMs. So create a new macro to use this offset and to avoid confusion between different OMAP parts. For more information, see the tables in TRM for named something like "Device Core Control Module Pad Configuration Register Fields" and "Device Wake-Up Control Module Pad Configuration Register Fields" Note that we now also have to update cm-t54 for the fixed up offsets. Signed-off-by: Joachim Eastwood [tony@atomide.com: updated comments, updated cm-t54] Signed-off-by: Tony Lindgren

ARM: dts: Fix omap serial wake-up when booted with device tree

2014-05-06T20:48:35+00:00

We've had deeper idle states working on omaps for few years now, but only in the legacy mode. When booted with device tree, the wake-up events did not have a chance to work until commit 3e6cee1786a1 (pinctrl: single: Add support for wake-up interrupts) that recently got merged. In addition to that we also needed commit 79d9701559a9 (of/irq: create interrupts-extended property) and 9ec36cafe43b (of/irq: do irq resolution in platform_get_irq) that are now also merged. So let's fix the wake-up events for some selected omaps so devices booted in device tree mode won't just hang if deeper power states are enabled, and so systems can wake up from suspend to the serial port event. Note that there's no longer need to specify the wake-up bit in the pinctrl settings, the request_irq on the wake-up pin takes care of that. Cc: devicetree@vger.kernel.org Cc: "Benoît Cousson" Cc: Kevin Hilman Cc: Nishanth Menon Cc: Paul Walmsley Cc: Tero Kristo [tony@atomide.com: updated comments, added board LDP] Signed-off-by: Tony Lindgren