kernel/git/stable/linux.git/net/mac80211/tx.c, branch linux-4.13.y

mac80211: fix VLAN handling with TXQs

2017-10-05T07:47:25+00:00

commit 53168215909281a09d3afc6fb51a9d4f81f74d39 upstream. With TXQs, the AP_VLAN interfaces are resolved to their owner AP interface when enqueuing the frame, which makes sense since the frame really goes out on that as far as the driver is concerned. However, this introduces a problem: frames to be encrypted with a VLAN-specific GTK will now be encrypted with the AP GTK, since the information about which virtual interface to use to select the key is taken from the TXQ. Fix this by preserving info->control.vif and using that in the dequeue function. This now requires doing the driver-mapping in the dequeue as well. Since there's no way to filter the frames that are sitting on a TXQ, drop all frames, which may affect other interfaces, when an AP_VLAN is removed. Signed-off-by: Johannes Berg Signed-off-by: Greg Kroah-Hartman

networking: make skb_push & __skb_push return void pointers

2017-06-16T15:48:40+00:00

It seems like a historic accident that these return unsigned char *, and in many places that means casts are required, more often than not. Make these functions return void * and remove all the casts across the tree, adding a (u8 *) cast only where the unsigned char pointer was used directly, all done with the following spatch: @@ expression SKB, LEN; typedef u8; identifier fn = { skb_push, __skb_push, skb_push_rcsum }; @@ - *(fn(SKB, LEN)) + *(u8 *)fn(SKB, LEN) @@ expression E, SKB, LEN; identifier fn = { skb_push, __skb_push, skb_push_rcsum }; type T; @@ - E = ((T *)(fn(SKB, LEN))) + E = fn(SKB, LEN) @@ expression SKB, LEN; identifier fn = { skb_push, __skb_push, skb_push_rcsum }; @@ - fn(SKB, LEN)[0] + *(u8 *)fn(SKB, LEN) Note that the last part there converts from push(...)[0] to the more idiomatic *(u8 *)push(...). Signed-off-by: Johannes Berg Signed-off-by: David S. Miller

networking: make skb_put & friends return void pointers

2017-06-16T15:48:39+00:00

It seems like a historic accident that these return unsigned char *, and in many places that means casts are required, more often than not. Make these functions (skb_put, __skb_put and pskb_put) return void * and remove all the casts across the tree, adding a (u8 *) cast only where the unsigned char pointer was used directly, all done with the following spatch: @@ expression SKB, LEN; typedef u8; identifier fn = { skb_put, __skb_put }; @@ - *(fn(SKB, LEN)) + *(u8 *)fn(SKB, LEN) @@ expression E, SKB, LEN; identifier fn = { skb_put, __skb_put }; type T; @@ - E = ((T *)(fn(SKB, LEN))) + E = fn(SKB, LEN) which actually doesn't cover pskb_put since there are only three users overall. A handful of stragglers were converted manually, notably a macro in drivers/isdn/i4l/isdn_bsdcomp.c and, oddly enough, one of the many instances in net/bluetooth/hci_sock.c. In the former file, I also had to fix one whitespace problem spatch introduced. Signed-off-by: Johannes Berg Signed-off-by: David S. Miller

networking: introduce and use skb_put_data()

2017-06-16T15:48:37+00:00

A common pattern with skb_put() is to just want to memcpy() some data into the new space, introduce skb_put_data() for this. An spatch similar to the one for skb_put_zero() converts many of the places using it: @@ identifier p, p2; expression len, skb, data; type t, t2; @@ ( -p = skb_put(skb, len); +p = skb_put_data(skb, data, len); | -p = (t)skb_put(skb, len); +p = skb_put_data(skb, data, len); ) ( p2 = (t2)p; -memcpy(p2, data, len); | -memcpy(p, data, len); ) @@ type t, t2; identifier p, p2; expression skb, data; @@ t *p; ... ( -p = skb_put(skb, sizeof(t)); +p = skb_put_data(skb, data, sizeof(t)); | -p = (t *)skb_put(skb, sizeof(t)); +p = skb_put_data(skb, data, sizeof(t)); ) ( p2 = (t2)p; -memcpy(p2, data, sizeof(*p)); | -memcpy(p, data, sizeof(*p)); ) @@ expression skb, len, data; @@ -memcpy(skb_put(skb, len), data, len); +skb_put_data(skb, data, len); (again, manually post-processed to retain some comments) Reviewed-by: Stephen Hemminger Signed-off-by: Johannes Berg Signed-off-by: David S. Miller

networking: convert many more places to skb_put_zero()

2017-06-16T15:48:35+00:00

There were many places that my previous spatch didn't find, as pointed out by yuan linyu in various patches. The following spatch found many more and also removes the now unnecessary casts: @@ identifier p, p2; expression len; expression skb; type t, t2; @@ ( -p = skb_put(skb, len); +p = skb_put_zero(skb, len); | -p = (t)skb_put(skb, len); +p = skb_put_zero(skb, len); ) ... when != p ( p2 = (t2)p; -memset(p2, 0, len); | -memset(p, 0, len); ) @@ type t, t2; identifier p, p2; expression skb; @@ t *p; ... ( -p = skb_put(skb, sizeof(t)); +p = skb_put_zero(skb, sizeof(t)); | -p = (t *)skb_put(skb, sizeof(t)); +p = skb_put_zero(skb, sizeof(t)); ) ... when != p ( p2 = (t2)p; -memset(p2, 0, sizeof(*p)); | -memset(p, 0, sizeof(*p)); ) @@ expression skb, len; @@ -memset(skb_put(skb, len), 0, len); +skb_put_zero(skb, len); Apply it to the tree (with one manual fixup to keep the comment in vxlan.c, which spatch removed.) Signed-off-by: Johannes Berg Signed-off-by: David S. Miller

mac80211: Dynamically set CoDel parameters per station

2017-05-17T14:03:40+00:00

CoDel can be too aggressive if a station sends at a very low rate, leading reduced throughput. This gets worse the more stations are present, as each station gets more bursty the longer the round-robin scheduling between stations takes. This adds dynamic adjustment of CoDel parameters per station. It uses the rate selection information to estimate throughput and sets more lenient CoDel parameters if the estimated throughput is below a threshold (modified by the number of active stations). A new callback is added that drivers can use to notify mac80211 about changes in expected throughput, so the same adjustment can be made for cards that implement rate control in firmware. Drivers that don't use this will just get the default parameters. Signed-off-by: Toke Høiland-Jørgensen [remove currently unnecessary EXPORT_SYMBOL, fix kernel-doc, remove inline annotation] Signed-off-by: Johannes Berg

mac80211: Fix possible sband related NULL pointer de-reference

2017-04-28T10:28:44+00:00

Existing API 'ieee80211_get_sdata_band' returns default 2 GHz band even if the channel context configuration is NULL. This crashes for chipsets which support 5 Ghz alone when it tries to access members of 'sband'. Channel context configuration can be NULL in multivif case and when channel switch is in progress (or) when it fails. Fix this by replacing the API 'ieee80211_get_sdata_band' with 'ieee80211_get_sband' which returns a NULL pointer for sband when the channel configuration is NULL. An example scenario is as below: In multivif mode (AP + STA) with drivers like ath10k, when we do a channel switch in the AP vif (which has a number of clients connected) and a STA vif which is connected to some other AP, when the channel switch in AP vif fails, while the STA vifs tries to connect to the other AP, there is a window where the channel context is NULL/invalid and this results in a crash while the clients connected to the AP vif tries to reconnect and this race is very similar to the one investigated by Michal in https://patchwork.kernel.org/patch/3788161/ and this does happens with hardware that supports 5Ghz alone after long hours of testing with continuous channel switch on the AP vif ieee80211 phy0: channel context reservation cannot be finalized because some interfaces aren't switching wlan0: failed to finalize CSA, disconnecting wlan0-1: deauthenticating from 8c:fd:f0:01:54:9c by local choice (Reason: 3=DEAUTH_LEAVING) WARNING: CPU: 1 PID: 19032 at net/mac80211/ieee80211_i.h:1013 sta_info_alloc+0x374/0x3fc [mac80211] [] (sta_info_alloc [mac80211]) [] (ieee80211_add_station [mac80211])) [] (nl80211_new_station [cfg80211]) Unable to handle kernel NULL pointer dereference at virtual address 00000014 pgd = d5f4c000 Internal error: Oops: 17 [#1] PREEMPT SMP ARM PC is at sta_info_alloc+0x380/0x3fc [mac80211] LR is at sta_info_alloc+0x37c/0x3fc [mac80211] [] (sta_info_alloc [mac80211]) [] (ieee80211_add_station [mac80211]) [] (nl80211_new_station [cfg80211])) Cc: Michal Kazior Signed-off-by: Mohammed Shafi Shajakhan Signed-off-by: Johannes Berg

mac80211: remove ieee80211_tx_rate_control.max_rate_idx

2017-03-07T08:42:12+00:00

As promised a little more than 7 years ago, remove it now since nothing uses it anymore. Signed-off-by: Johannes Berg

mac80211: use helper function to access ieee802_1d_to_ac[]

2017-01-26T08:50:44+00:00

cleanup patch to make use of ieee80211_ac_from_tid() to retrieve ac from ieee802_1d_to_ac[] Signed-off-by: Amadeusz Sławiński Signed-off-by: Johannes Berg

Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net

2017-01-17T20:19:37+00:00