kernel/git/stable/linux.git/sound/usb, branch linux-5.13.y

ALSA: usb-audio: Add registration quirk for JBL Quantum 800

2021-09-12T06:59:58+00:00

commit c8b177b6e3a005bd8fb0395a4bc5db3470301c28 upstream. Add another device ID for JBL Quantum 800. It requires the same quirk as other JBL Quantum devices. Signed-off-by: Alexander Tsoy Cc: Link: https://lore.kernel.org/r/20210831002531.116957-1-alexander@tsoy.me Signed-off-by: Takashi Iwai Signed-off-by: Greg Kroah-Hartman

ALSA: usb-audio: Fix regression on Sony WALKMAN NW-A45 DAC

2021-09-08T06:50:21+00:00

commit 7af5a14371c1cf94a41f08eabb62a3faceec8911 upstream. We've got a regression report for USB-audio with Sony WALKMAN NW-A45 DAC device where no sound is audible on recent kernel. The bisection resulted in the code change wrt endpoint management, and the further debug session revealed that it was caused by the order of the USB audio interface. In the earlier code, we always set up the USB interface at first before other setups, but it was changed to be done at the last for UAC2/3, which is more standard way, while keeping the old way for UAC1. OTOH, this device seems requiring the setup of the interface at first just like UAC1. This patch works around the regression by applying the interface setup specifically for the WALKMAN at the beginning of the endpoint setup procedure. This change is written straightforwardly to be easily backported in old kernels. A further cleanup to move the workaround into a generic quirk section will follow in a later patch. Fixes: bf6313a0ff76 ("ALSA: usb-audio: Refactor endpoint management") Cc: BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=214105 Link: https://lore.kernel.org/r/20210824054700.8236-1-tiwai@suse.de Signed-off-by: Takashi Iwai Signed-off-by: Greg Kroah-Hartman

ALSA: usb-audio: Avoid unnecessary or invalid connector selection at resume

2021-08-12T11:32:14+00:00

commit 8dde723fcde4479f256441da03793e37181d9f21 upstream. The recent fix for the resume on Lenovo machines seems causing a regression on others. It's because the change always triggers the connector selection no matter which widget node type is. This patch addresses the regression by setting the resume callback selectively only for the connector widget. Fixes: 44609fc01f28 ("ALSA: usb-audio: Check connector value on resume") Cc: BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=213897 Link: https://lore.kernel.org/r/20210729185126.24432-1-tiwai@suse.de Signed-off-by: Takashi Iwai Signed-off-by: Greg Kroah-Hartman

ALSA: usb-audio: Add registration quirk for JBL Quantum 600

2021-08-12T11:32:14+00:00

commit 4b0556b96e1fe7723629bd40e3813a30cd632faf upstream. Apparently JBL Quantum 600 has multiple hardware revisions. Apply registration quirk to another device id as well. Signed-off-by: Alexander Tsoy Cc: Link: https://lore.kernel.org/r/20210727093326.1153366-1-alexander@tsoy.me Signed-off-by: Takashi Iwai Signed-off-by: Greg Kroah-Hartman

ALSA: usb-audio: Fix superfluous autosuspend recovery

2021-08-12T11:32:14+00:00

commit 66291b6adb66dd3bc96b0f594d88c2ff1300d95f upstream. The change to restore the autosuspend from the disabled state uses a wrong check: namely, it should have been the exact comparison of the quirk_type instead of the bitwise and (&). Otherwise it matches wrongly with the other quirk types. Although re-enabling the autosuspend for the already enabled device shouldn't matter much, it's better to fix the unbalanced call. Fixes: 9799110825db ("ALSA: usb-audio: Disable USB autosuspend properly in setup_disable_autosuspend()") Cc: Link: https://lore.kernel.org/r/s5hr1flh9ov.wl-tiwai@suse.de Signed-off-by: Takashi Iwai Signed-off-by: Greg Kroah-Hartman

ALSA: usb-audio: fix incorrect clock source setting

2021-08-12T11:32:04+00:00

[ Upstream commit 4511781f95da0a3b2bad34f3f5e3967e80cd2d18 ] The following scenario describes an echo test for Samsung USBC Headset (AKG) with VID/PID (0x04e8/0xa051). We first start a capture stream(USB IN transfer) in 96Khz/24bit/1ch mode. In clock find source function, we get value 0x2 for clock selector and 0x1 for clock source. Kernel-4.14 behavior Since clock source is valid so clock selector was not set again. We pass through this function and start a playback stream(USB OUT transfer) in 48Khz/32bit/2ch mode. This time we get value 0x1 for clock selector and 0x1 for clock source. Finally clock id with this setting is 0x9. Kernel-5.10 behavior Clock selector was always set one more time even it is valid. When we start a playback stream, we will get 0x2 for clock selector and 0x1 for clock source. In this case clock id becomes 0xA. This is an incorrect clock source setting and results in severe noises. We see wrong data rate in USB IN transfer. (From 288 bytes/ms becomes 144 bytes/ms) It should keep in 288 bytes/ms. This earphone works fine on older kernel version load because this is a newly-added behavior. Fixes: d2e8f641257d ("ALSA: usb-audio: Explicitly set up the clock selector") Signed-off-by: chihhao.chen Link: https://lore.kernel.org/r/1627100621-19225-1-git-send-email-chihhao.chen@mediatek.com Signed-off-by: Takashi Iwai Signed-off-by: Sasha Levin

ALSA: usb-audio: Add registration quirk for JBL Quantum headsets

2021-07-28T12:37:35+00:00

commit b0084afde27fe8a504377dee65f55bc6aa776937 upstream. These devices has two interfaces, but only the second interface contains the capture endpoint, thus quirk is required to delay the registration until the second interface appears. Tested-by: Jakub Fišer Signed-off-by: Alexander Tsoy Cc: Link: https://lore.kernel.org/r/20210721235605.53741-1-alexander@tsoy.me Signed-off-by: Takashi Iwai Signed-off-by: Greg Kroah-Hartman

ALSA: usb-audio: Add missing proc text entry for BESPOKEN type

2021-07-28T12:37:34+00:00

commit 64752a95b702817602d72f109ceaf5ec0780e283 upstream. Recently we've added a new usb_mixer element type, USB_MIXER_BESPOKEN, but it wasn't added in the table in snd_usb_mixer_dump_cval(). This is no big problem since each bespoken type should have its own dump method, but it still isn't disallowed to use the standard one, so we should cover it as well. Along with it, define the table with the explicit array initializer for avoiding other pitfalls. Fixes: 785b6f29a795 ("ALSA: usb-audio: scarlett2: Fix wrong resume call") Reported-by: Pavel Machek Cc: Link: https://lore.kernel.org/r/20210714084836.1977-1-tiwai@suse.de Signed-off-by: Takashi Iwai Signed-off-by: Greg Kroah-Hartman

ALSA: usb-audio: scarlett2: Fix 6i6 Gen 2 line out descriptions

2021-07-20T14:00:21+00:00

[ Upstream commit c712c6c0ff2d60478582e337185bcdd520a7dc2e ] There are two headphone outputs, and they map to the four analogue outputs. Signed-off-by: Geoffrey D. Bennett Link: https://lore.kernel.org/r/205e5e5348f08ded0cc4da5446f604d4b91db5bf.1624294591.git.g@b4.vu Signed-off-by: Takashi Iwai Signed-off-by: Sasha Levin

ALSA: usb-audio: scarlett2: Fix scarlett2_*_ctl_put() return values

2021-07-20T14:00:20+00:00

[ Upstream commit c5d8e008032f3cd5f266d552732973a960b0bd4b ] Mixer control put callbacks should return 1 if the value is changed. Fix the sw_hw, level, pad, and button controls accordingly. Signed-off-by: Geoffrey D. Bennett Link: https://lore.kernel.org/r/20210620164645.GA9221@m.b4.vu Signed-off-by: Takashi Iwai Signed-off-by: Sasha Levin