| Age | Commit message (Collapse) | Author |
|---|
|
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When we handle a TX completion for an XDP packet, it is not counted
in the per-TXQ netdev stats. Record it in new internal counters,
and include those in the device-wide total in efx_get_base_stats().
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The previous patch changed when we increment the RX queue's rx_packets
counter, to match the semantics of netdev per-queue stats. The
differences between the old and new counts are scatter errors (which
produce a WARN_ON) and this counter, which is incremented by
efx_rx_packet__check_len() when an RX packet (which was placed in a
single buffer by SG, i.e. n_frags == 1) has a length (from the RX
event) which is too long to fit in the RX buffer. If this occurs, we
drop the packet and fire a ratelimited netif_err().
The counter previously was not reported anywhere; add it to ethtool -S
output to ensure users still have this information.
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Just RX and TX packet counts and TX bytes for now. We do not
have per-queue RX byte counts, which causes us to fail
stats.pkt_byte_sum selftest with "Drivers should always report
basic keys" error.
Per-queue counts are since the last time the queue was inited
(typically by efx_start_datapath(), on ifup or reconfiguration);
device-wide total (efx_get_base_stats()) is since driver probe.
This is not the same lifetime as rtnl_link_stats64, which uses
firmware stats which count since FW (re)booted; this can cause a
"Qstats are lower" or "RTNL stats are lower" failure in
stats.pkt_byte_sum selftest.
Move the increment of rx_queue->rx_packets to match the semantics
specified for netdev per-queue stats, i.e. just before handing
the packet to XDP (if present) or the netstack (through GRO).
This will affect the existing ethtool -S output which also
reports these counters.
XDP TX packets are not yet counted into base_stats.
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The n_rx_tobe_disc and n_rx_mcast_mismatch counters are a legacy
from farch, and are never written in EF10 or EF100 code. Remove
them from the struct and from ethtool -S output, saving a bit of
memory and avoiding user confusion.
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In STA+AP concurrent mode, performing a scan operation on one vif
temporarily stops beacons on the other. When the scan is completed,
beacons are enabled again with BSS_CHANGED_BEACON_ENABLED.
We can observe that no beacons are being sent when just
rtl8xxxu_start_tx_beacon() is being called.
Thus, also perform update_beacon_work in order to restore beaconing.
Fixes: cde8848cad0b ("wifi: rtl8xxxu: Add beacon functions")
Signed-off-by: Martin Kaistra <martin.kaistra@linutronix.de>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240930084955.455241-1-martin.kaistra@linutronix.de
|
|
In range test, the RSSI is helpful to check attenuation of cable and align
difference between environments. Since data packets can be transmitted with
different rate and power, the RSSI of all packets can be variant.
Oppositely beacon is transmitted with the same rate and power, so beacon
RSSI will be relatively invariant, and more helpful to diagnose problems.
The output of beacon RSSI in unit of dBm looks like:
Beacon: 19 (-33 dBm), TF: 0
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240927013512.7106-1-pkshih@realtek.com
|
|
After commit 0edb555a65d1 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/net after the previous
conversion commits apart from the wireless drivers to use .remove(),
with the eventual goal to drop struct platform_driver::remove_new(). As
.remove() and .remove_new() have the same prototypes, conversion is done
by just changing the structure member name in the driver initializer.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
After commit 0edb555a65d1 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/net/mdio to use .remove(),
with the eventual goal to drop struct platform_driver::remove_new(). As
.remove() and .remove_new() have the same prototypes, conversion is done
by just changing the structure member name in the driver initializer.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/0b60d8bfc45a3de8193f953794dda241e11032a9.1727949050.git.u.kleine-koenig@baylibre.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
After commit 0edb555a65d1 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/net/dsa to use .remove(),
with the eventual goal to drop struct platform_driver::remove_new(). As
.remove() and .remove_new() have the same prototypes, conversion is done
by just changing the structure member name in the driver initializer.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/36da477cb9fa0bffec32d50c2cf3d18e94a0e7e3.1727949050.git.u.kleine-koenig@baylibre.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
After commit 0edb555a65d1 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/net/ethernet to use
.remove(), with the eventual goal to drop struct
platform_driver::remove_new(). As .remove() and .remove_new() have the
same prototypes, conversion is done by just changing the structure
member name in the driver initializer.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://patch.msgid.link/18f7c585a1a8a8ac8b03a2fca7de19bd5c52ac2b.1727949050.git.u.kleine-koenig@baylibre.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If phy_read_mmd() fails, the error code stored in 'bmsr' should be returned
instead of 'val' which is likely to be 0.
Fixes: 75f4d8d10e01 ("net: phy: add Broadcom BCM84881 PHY driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://patch.msgid.link/3e1755b0c40340d00e089d6adae5bca2f8c79e53.1727982168.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The SF2 crossbar register is a packed bitfield, giving the index of the
external port selected for each of the internal ports. On BCM4908 (the
only currently-supported switch family with a crossbar), there are 2
internal ports and 3 external ports, so there are 2 bits per internal
port.
The driver currently conflates the "bits per port" and "number of ports"
concepts, lumping both into the `num_crossbar_int_ports` field. Since it
is currently only possible for either of these counts to have a value of
2, there is no behavioral error resulting from this situation for now.
Make the code more readable (and support the future possibility of
larger crossbars) by adding a `num_crossbar_ext_bits` field to represent
the "bits per port" count and relying on this where appropriate instead.
Signed-off-by: Sam Edwards <CFSworks@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20241003212301.1339647-1-CFSworks@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This adds control over the hardware LEDs in the Marvell
MV88E6xxx DSA switch and enables it for MV88E6352.
This fixes an imminent problem on the Inteno XG6846 which
has a WAN LED that simply do not work with hardware
defaults: driver amendment is necessary.
The patch is modeled after Christian Marangis LED support
code for the QCA8k DSA switch, I got help with the register
definitions from Tim Harvey.
After this patch it is possible to activate hardware link
indication like this (or with a similar script):
cd /sys/class/leds/Marvell\ 88E6352:05:00:green:wan/
echo netdev > trigger
echo 1 > link
This makes the green link indicator come up on any link
speed. It is also possible to be more elaborate, like this:
cd /sys/class/leds/Marvell\ 88E6352:05:00:green:wan/
echo netdev > trigger
echo 1 > link_1000
cd /sys/class/leds/Marvell\ 88E6352:05:01:amber:wan/
echo netdev > trigger
echo 1 > link_100
Making the green LED come on for a gigabit link and the
amber LED come on for a 100 mbit link.
Each port has 2 LED slots (the hardware may use just one or
none) and the hardware triggers are specified in four bits per
LED, and some of the hardware triggers are only available on the
SFP (fiber) uplink. The restrictions are described in the
port.h header file where the registers are described. For
example, selector 1 set for LED 1 on port 5 or 6 will indicate
Fiber 1000 (gigabit) and activity with a blinking LED, but
ONLY for an SFP connection. If port 5/6 is used with something
not SFP, this selector is a noop: something else need to be
selected.
After the previous series rewriting the MV88E6xxx DT
bindings to use YAML a "leds" subnode is already valid
for each port, in my scratch device tree it looks like
this:
leds {
#address-cells = <1>;
#size-cells = <0>;
led@0 {
reg = <0>;
color = <LED_COLOR_ID_GREEN>;
function = LED_FUNCTION_LAN;
default-state = "off";
linux,default-trigger = "netdev";
};
led@1 {
reg = <1>;
color = <LED_COLOR_ID_AMBER>;
function = LED_FUNCTION_LAN;
default-state = "off";
};
};
This DT config is not yet configuring everything: when the netdev
default trigger is assigned the hw acceleration callbacks are
not called, and there is no way to set the netdev sub-trigger
type (such as link_1000) from the device tree, such as if you want
a gigabit link indicator. This has to be done from userspace at
this point.
We add LED operations to all switches in the 6352 family:
6172, 6176, 6240 and 6352.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241001-mv88e6xxx-leds-v4-1-cc11c4f49b18@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
PSE controllers like the TPS23881 can forcefully turn off their
configuration state. In such cases, the is_enabled() and get_status()
callbacks will report the PSE as disabled, while admin_state_enabled
will show it as enabled. This mismatch can lead the user to attempt
to enable it, but no action is taken as admin_state_enabled remains set.
The solution is to disable the PSE before enabling it, ensuring the
actual status matches admin_state_enabled.
Fixes: d83e13761d5b ("net: pse-pd: Use regulator framework within PSE framework")
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241002121706.246143-1-kory.maincent@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Current code allocates the pcpu_sum array with size num_possible_cpus().
This code assumes the cpu_possible_mask is dense, which is not true in
the general case per [1]. If cpu_possible_mask is sparse, the array
might be indexed by a value beyond the size of the array.
However, the configurations that Hyper-V provides to guest VMs on x86
and ARM64 hardware, in combination with how architecture specific code
assigns Linux CPU numbers, *does* always produce a dense cpu_possible_mask.
So the dense assumption is not currently causing failures. But for
robustness against future changes in how cpu_possible_mask is populated,
update the code to no longer assume dense.
The correct approach is to allocate and initialize the array using size
"nr_cpu_ids". While this leaves unused array entries corresponding to
holes in cpu_possible_mask, the holes are assumed to be minimal and hence
the amount of memory wasted by unused entries is minimal.
[1] https://lore.kernel.org/lkml/SN6PR02MB4157210CC36B2593F8572E5ED4692@SN6PR02MB4157.namprd02.prod.outlook.com/
Signed-off-by: Michael Kelley <mhklinux@outlook.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://patch.msgid.link/20241003035333.49261-6-mhklinux@outlook.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2024-10-01 (ice)
This series contains updates to ice driver only.
Karol cleans up current PTP GPIO pin handling, fixes minor bugs,
refactors implementation for all products, introduces SDP (Software
Definable Pins) for E825C and implements reading SDP section from NVM
for E810 products.
Sergey replaces multiple aux buses and devices used in the PTP support
code with struct ice_adapter holding the necessary shared data.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
ice: Drop auxbus use for PTP to finalize ice_adapter move
ice: Use ice_adapter for PTP shared data instead of auxdev
ice: Initial support for E825C hardware in ice_adapter
ice: Add ice_get_ctrl_ptp() wrapper to simplify the code
ice: Introduce ice_get_phy_model() wrapper
ice: Enable 1PPS out from CGU for E825C products
ice: Read SDP section from NVM for pin definitions
ice: Disable shared pin on E810 on setfunc
ice: Cache perout/extts requests and check flags
ice: Align E810T GPIO to other products
ice: Add SDPs support for E825C
ice: Implement ice_ptp_pin_desc
====================
Link: https://patch.msgid.link/20241001201702.3252954-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Previously, the TX header requirement for standard frames was ignored.
This requirement is a bitstring sent from the VIOS which maps to the
type of header information needed during TX. If no header information,
is needed then send subcrq direct can be used (which can be more
performant).
This bitstring was previously ignored for standard packets (AKA non LSO,
non CSO) due to the belief that the bitstring was over-cautionary. It
turns out that there are some configurations where the backing device
does need header information for transmission of standard packets. If
the information is not supplied then this causes continuous "Adapter
error" transport events. Therefore, this bitstring should be respected
and observed before considering the use of send subcrq direct.
Fixes: 74839f7a8268 ("ibmvnic: Introduce send sub-crq direct")
Signed-off-by: Nick Child <nnac123@linux.ibm.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241001163200.1802522-2-nnac123@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
It no longer serves any purpose and is identical to mlx5_fc_create upon
which it was originally based of.
Signed-off-by: Cosmin Ratiu <cratiu@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20241001103709.58127-7-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
num_counters is only used for deciding whether to grow the bulk query
buffer, which is done once more counters than a small initial threshold
are present. After that, maintaining num_counters serves no purpose.
This commit replaces that with an actual xarray traversal to count the
counters. This appears expensive at first sight, but is only done when
the number of counters is less than the initial threshold (8) and only
once every sampling interval. Once the number of counters goes above the
threshold, the bulk query buffer is grown to max size and the xarray
traversal is never done again.
Signed-off-by: Cosmin Ratiu <cratiu@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20241001103709.58127-6-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The mlx5_fc struct has a cache for values queried from hw, which is
cacheline aligned. On x86_64, this results in:
struct mlx5_fc {
u32 id; /* 0 4 */
bool aging; /* 4 1 */
/* XXX 3 bytes hole, try to pack */
struct mlx5_fc_bulk * bulk; /* 8 8 */
/* XXX 48 bytes hole, try to pack */
/* --- cacheline 1 boundary (64 bytes) --- */
struct mlx5_fc_cache cache __attribute__((__aligned__(64)));
/* 64 24 */
u64 lastpackets; /* 88 8 */
u64 lastbytes; /* 96 8 */
/* size: 128, cachelines: 2, members: 6 */
/* sum members: 53, holes: 2, sum holes: 51 */
/* padding: 24 */
/* forced aligns: 1, forced holes: 1, sum forced holes: 48 */
} __attribute__((__aligned__(64)));
(output from pahole).
...So a 48+24=72 byte waste. As far as I can determine, this serves no
purpose other than maybe making sure that the values in the cache do not
span two cachelines in the worst case scenario, but that's not a valid
enough reason to waste 72 bytes per counter, especially since this code
is not performance-critical. There could potentially be hundreds of
thousands of counters (e.g. for connection-tracking), so this quickly
adds up to multiple MB wasted.
This commit removes the alignment, resulting in:
struct mlx5_fc {
[...]
/* size: 56, cachelines: 1, members: 6 */
/* sum members: 53, holes: 1, sum holes: 3 */
/* last cacheline: 56 bytes */
};
Signed-off-by: Cosmin Ratiu <cratiu@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20241001103709.58127-5-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Previously, managing counters was a complicated affair involving an IDR,
a sorted double linked list, two single linked lists and a complex dance
between a non-periodic wq task and users adding/deleting counters.
Adding was done by inserting new counters into the IDR and into a single
linked list, leaving the wq to process the list and actually add the
counters into the double linked list, maintained sorted with the IDR.
Deleting involved adding the counter into another single linked list,
leaving the wq to actually unlink the counter from the other structures
and release it.
Dumping the counters is done with the bulk query API, which relies on
the counter list being sorted and unmutable during querying to
efficiently retrieve cached counter values.
Finally, the IDR data struct is deprecated.
This commit replaces all of that with an xarray.
Adding is now done directly, by using xa_lock.
Deleting is also done directly, under the xa_lock.
Querying is done from a periodic task running every sampling_interval
(default 1s) and uses the bulk query API for efficiency.
It works by iterating over the xarray:
- when a new bulk needs to be started, the bulk information is computed
under the xa_lock.
- the xa iteration state is saved and the xa_lock dropped.
- the HW is queried for bulk counter values.
- the xa_lock is reacquired.
- counter caches with ids covered by the bulk response are updated.
Querying always requests the max bulk length, for simplicity.
Counters could be added/deleted while the HW is queried. This is safe,
as the HW API simply returns unknown values for counters not in HW, but
those values won't be accessed. Only counters present in xarray before
bulk query will actually read queried cache values.
This cuts down the size of mlx5_fc by 4 pointers (88->56 bytes), which
amounts to ~3MB / 100K counters.
But more importantly, this solves the wq spinlock congestion issue seen
happening on high-rate counter insertion+deletion.
Signed-off-by: Cosmin Ratiu <cratiu@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20241001103709.58127-4-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The bulk query buffer starts out small (see [1]) and as soon as the
number of counters goes past the initial threshold grows to max
size (32K entries, 512KB) with a retry scheme.
This commit switches to using kvmalloc for the buffer, which has a near
zero likelihood of failing, and thus the explicit retry scheme becomes
superfluous and is taken out. On the low chance the allocation fails, it
will still be retried every sampling_interval, when the wq task runs.
[1] commit b247f32aecad ("net/mlx5: Dynamically resize flow counters
query buffer")
Signed-off-by: Cosmin Ratiu <cratiu@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20241001103709.58127-3-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The mlx5_fc_stats and mlx5_fc_pool structs are only used from
fs_counters.c. As such, make them private there.
mlx5_fc_pool is not used or referenced at all outside fs_counters.
mlx5_fc_stats is referenced from mlx5_core_dev, so instead of having it
as a direct member (which requires exporting it from fs_counters), store
a pointer to it, allocate it on init and clear it on destroy.
One caveat is that a simple container_of to get from a 'work' struct to
the outermost mlx5_core_dev struct directly no longer works, so an extra
pointer had to be added to mlx5_fc_stats back to the parent dev.
Signed-off-by: Cosmin Ratiu <cratiu@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20241001103709.58127-2-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The blamed commit introduced an unexpected regression in the sja1105
driver. Packets from VLAN-unaware bridge ports get received correctly,
but the protocol stack can't seem to decode them properly.
For ds->untag_bridge_pvid users (thus also sja1105), the blamed commit
did introduce a functional change: dsa_switch_rcv() used to call
dsa_untag_bridge_pvid(), which looked like this:
err = br_vlan_get_proto(br, &proto);
if (err)
return skb;
/* Move VLAN tag from data to hwaccel */
if (!skb_vlan_tag_present(skb) && skb->protocol == htons(proto)) {
skb = skb_vlan_untag(skb);
if (!skb)
return NULL;
}
and now it calls dsa_software_vlan_untag() which has just this:
/* Move VLAN tag from data to hwaccel */
if (!skb_vlan_tag_present(skb)) {
skb = skb_vlan_untag(skb);
if (!skb)
return NULL;
}
thus lacks any skb->protocol == bridge VLAN protocol check. That check
is deferred until a later check for skb->vlan_proto (in the hwaccel area).
The new code is problematic because, for VLAN-untagged packets,
skb_vlan_untag() blindly takes the 4 bytes starting with the EtherType
and turns them into a hwaccel VLAN tag. This is what breaks the protocol
stack.
It would be tempting to "make it work as before" and only call
skb_vlan_untag() for those packets with the skb->protocol actually
representing a VLAN.
But the premise of the newly introduced dsa_software_vlan_untag() core
function is not wrong. Drivers set ds->untag_bridge_pvid or
ds->untag_vlan_aware_bridge_pvid presumably because they send all
traffic to the CPU reception path as VLAN-tagged. So why should we spend
any additional CPU cycles assuming that the packet may be VLAN-untagged?
And why does the sja1105 driver opt into ds->untag_bridge_pvid if it
doesn't always deliver packets to the CPU as VLAN-tagged?
The answer to the latter question is indeed more interesting: it doesn't
need to. This got done in commit 884be12f8566 ("net: dsa: sja1105: add
support for imprecise RX"), because I thought it would be needed, but I
didn't realize that it doesn't actually make a difference.
As explained in the commit message of the blamed patch, ds->untag_bridge_pvid
only makes a difference in the VLAN-untagged receive path of a bridge port.
However, in that operating mode, tag_sja1105.c makes use of VLAN tags
with the ETH_P_SJA1105 TPID, and it decodes and consumes these VLAN tags
as if they were DSA tags (aka tag_8021q operation). Even if commit
884be12f8566 ("net: dsa: sja1105: add support for imprecise RX") added
this logic in sja1105_bridge_vlan_add():
/* Always install bridge VLANs as egress-tagged on the CPU port. */
if (dsa_is_cpu_port(ds, port))
flags = 0;
that was for _bridge_ VLANs, which are _not_ committed to hardware
in VLAN-unaware mode (aka the mode where ds->untag_bridge_pvid does
anything at all). Even prior to that change, the tag_8021q VLANs
were always installed as egress-tagged on the CPU port, see
dsa_switch_tag_8021q_vlan_add():
u16 flags = 0; // egress-tagged, non-PVID
if (dsa_port_is_user(dp))
flags |= BRIDGE_VLAN_INFO_UNTAGGED |
BRIDGE_VLAN_INFO_PVID;
err = dsa_port_do_tag_8021q_vlan_add(dp, info->vid,
flags);
if (err)
return err;
Whether the sja1105 driver needs the new flag, ds->untag_vlan_aware_bridge_pvid,
rather than ds->untag_bridge_pvid, is a separate discussion. To fix the
current bug in VLAN-unaware bridge mode, I would argue that the sja1105
driver should not request something it doesn't need, rather than
complicating the core DSA helper. Whereas before the blamed commit, this
setting was harmless, now it has caused breakage.
Fixes: 93e4649efa96 ("net: dsa: provide a software untagging function on RX for VLAN-aware bridges")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20241001140206.50933-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Convert struct rvu_block block to const struct rvu_block *block in
get_lf_str_list() function parameter. This improves efficiency by
avoiding structure copying and reflects the function's read-only
access to block.
Signed-off-by: Riyan Dhiman <riyandhiman14@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241001110542.5404-2-riyandhiman14@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As per the SAMA5D2 device specification it supports Jumbo frames.
But the suggested flag and length of bytes it supports was not updated
in this driver config_structure.
The maximum jumbo frames the device supports:
10240 bytes as per the device spec.
While changing the MTU value greater than 1500, it threw error:
sudo ifconfig eth1 mtu 9000
SIOCSIFMTU: Invalid argument
Add this support to driver so that it works as expected and designed.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Reviewed-by: Simon Horman <horms@kernel.org>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://patch.msgid.link/20241003171941.8814-1-olek2@wp.pl
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Align PSE memory configuration to vendor SDK. In particular, increase
initial value of PSE reserved memory in airoha_fe_pse_ports_init()
routine by the value used for the second Packet Processor Engine (PPE2)
and do not overwrite the default value.
Introduced by commit 23020f049327 ("net: airoha: Introduce ethernet support
for EN7581 SoC")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241001-airoha-eth-pse-fix-v2-2-9a56cdffd074@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Store the default value for the number of PSE reserved pages in orig_val
at the beginning of airoha_fe_set_pse_oq_rsv routine, before updating it
with airoha_fe_set_pse_queue_rsv_pages().
Introduce airoha_fe_get_pse_all_rsv utility routine.
Introduced by commit 23020f049327 ("net: airoha: Introduce ethernet support
for EN7581 SoC")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241001-airoha-eth-pse-fix-v2-1-9a56cdffd074@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use device_for_each_child_node_scoped() to simplify the code by removing
the need for explicit calls to fwnode_handle_put() in every error path.
This approach also accounts for any error path that could be added.
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://patch.msgid.link/20240930-net-device_for_each_child_node_scoped-v2-2-35f09333c1d7@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There has already been an issue with the handling of early exits from
device_for_each_child() in this driver, and it was solved with commit
b1de5c78ebe9 ("net: mdio: thunder: Add missing fwnode_handle_put()") by
adding a call to fwnode_handle_put() right after the loop.
That solution is valid indeed, but if a new error path with a 'return'
is added to the loop, this solution will fail. A more secure approach
is using the scoped variant of the macro, which automatically
decrements the refcount of the child node when it goes out of scope,
removing the need for explicit calls to fwnode_handle_put().
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://patch.msgid.link/20240930-net-device_for_each_child_node_scoped-v2-1-35f09333c1d7@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
It is OK to sleep in qed_dmae_operation_wait, because it is called only
in process context, while holding p_hwfn->dmae_info.mutex from one of
the qed_dmae_{host,grc}2{host,grc} functions.
The udelay(DMAE_MIN_WAIT_TIME=2) in the function is too short to replace
with usleep_range, but at least it's a suitable point for checking if we
should give up the CPU with cond_resched().
This lowers the latency caused by 'ethtool -d' from 10 ms to less than
2 ms on my test system with voluntary preemption.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Link: https://patch.msgid.link/20240930201307.330692-5-mschmidt@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
qed_mcp_nvm_read has a loop where it calls qed_mcp_nvm_rd_cmd with the
argument b_can_sleep=false. And it sleeps once every 0x1000 bytes
read.
Simplify this by letting qed_mcp_nvm_rd_cmd itself sleep
(b_can_sleep=true). It will have slept at least once when successful
(in the "Wait for the MFW response" loop). So the extra sleep once every
0x1000 bytes becomes superfluous. Delete it.
On my test system with voluntary preemption, this lowers the latency
caused by 'ethtool -d' from 53 ms to 10 ms.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Link: https://patch.msgid.link/20240930201307.330692-4-mschmidt@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
On a kernel with preemption none or voluntary, 'ethtool -d'
on a qede network device can cause a big latency spike.
The biggest part of it is the loop in qed_grc_dump_ctx_data.
The function is called only from the .get_size and .perform_dump
callbacks for the "grc" feature defined in qed_features_lookup[].
As far as I can see, they are used in:
- qed's devlink healh reporter .dump op
- qede's ethtool get_regs/get_regs_len/get_dump_data ops
- qedf's qedf_get_grc_dump, called from:
- qedf_sysfs_write_grcdump - "grcdump" sysfs attribute write
- qedf_wq_grcdump - a workqueue
It is safe to sleep in all of them.
Let's insert a cond_resched() in the outer loop to let other tasks run.
Measured using this script:
#!/bin/bash
DEV=ens3f1
echo wakeup_rt > /sys/kernel/tracing/current_tracer
echo 0 > /sys/kernel/tracing/tracing_max_latency
echo 1 > /sys/kernel/tracing/tracing_on
echo "Setting the task CPU affinity"
taskset -p 1 $$ > /dev/null
echo "Starting the real-time task"
chrt -f 50 bash -c 'while sleep 0.01; do :; done' &
sleep 1
echo "Running: ethtool -d $DEV"
time ethtool -d $DEV > /dev/null
kill %1
echo 0 > /sys/kernel/tracing/tracing_on
echo "Measured latency: $(</sys/kernel/tracing/tracing_max_latency) us"
echo "To see the latency trace: less /sys/kernel/tracing/trace"
The patch lowers the latency from 180 ms to 53 ms on my test system with
voluntary preemption.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Link: https://patch.msgid.link/20240930201307.330692-3-mschmidt@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As a side effect of commit 5401c3e09928 ("qed: allow sleep in
qed_mcp_trace_dump()"), 'ethtool -d' became much slower.
Almost all the time is spent collecting the "mcp_trace".
It is caused by sleeping too long in _qed_mcp_cmd_and_union.
When called with sleeping not allowed, the function delays for 10 µs
between firmware polls. But if sleeping is allowed, it sleeps for 10 ms
instead.
The sleeps in _qed_mcp_cmd_and_union are unnecessarily long.
Replace msleep with usleep_range, which allows to achieve a similar
polling interval like in the no-sleeping mode (10 - 20 µs).
The only caller, qed_mcp_cmd_and_union, can stop doing the
multiplication/division of the usecs/max_retries. The polling interval
and the number of retries do not need to be parameters at all.
On my test system, 'ethtool -d' now takes 4 seconds instead of 44.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Link: https://patch.msgid.link/20240930201307.330692-2-mschmidt@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This clock should be optional. In addition, PTR_ERR can be -EPROBE_DEFER
in which case it should return.
devm_clk_get_optional_enabled also allows removing explicit clock enable
and disable calls.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20240930202951.297737-3-rosenp@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This combines multiple steps in one function.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20240930202951.297737-2-rosenp@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Effectively what's going on here is there's a main loop and an identical
one below with a single assignment. Simpler to move it up.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://patch.msgid.link/20240930181823.288892-6-rosenp@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
LIST_HEAD is a shorter macro. No real difference.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://patch.msgid.link/20240930181823.288892-5-rosenp@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
platform_get_drvdata is never called as a result of all the devm
conversions.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://patch.msgid.link/20240930181823.288892-4-rosenp@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
These functions can return EPROBE_DEFER. Don't warn in such a case.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://patch.msgid.link/20240930181823.288892-3-rosenp@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We can just use res directly.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://patch.msgid.link/20240930181823.288892-2-rosenp@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
alloc_ltalkdev in net/appletalk/dev.c is dead since
commit 00f3696f7555 ("net: appletalk: remove cops support")
Removing it (and it's helper) leaves dev.c and if_ltalk.h empty;
remove them and the Makefile entry.
tun.c was including that if_ltalk.h but actually wanted
the uapi version for LTALK_ALEN, fix up the path.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow tracking of packets sent with send_subcrq direct vs
indirect. `ethtool -S <dev>` will now provide a counter
of the number of uses of each xmit method. This metric will
be useful in performance debugging.
Signed-off-by: Nick Child <nnac123@linux.ibm.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241001163531.1803152-1-nnac123@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2024-09-30 (ice, idpf)
This series contains updates to ice and idpf drivers:
For ice:
Michal corrects setting of dst VSI on LAN filters and adds clearing of
port VLAN configuration during reset.
Gui-Dong Han corrects failures to decrement refcount in some error
paths.
Przemek resolves a memory leak in ice_init_tx_topology().
Arkadiusz prevents setting of DPLL_PIN_STATE_SELECTABLE to an improper
value.
Dave stops clearing of VLAN tracking bit to allow for VLANs to be properly
restored after reset.
For idpf:
Ahmed sets uninitialized dyn_ctl_intrvl_s value.
Josh corrects use and reporting of mailbox size.
Larysa corrects order of function calls during de-initialization.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
idpf: deinit virtchnl transaction manager after vport and vectors
idpf: use actual mbx receive payload length
idpf: fix VF dynamic interrupt ctl register initialization
ice: fix VLAN replay after reset
ice: disallow DPLL_PIN_STATE_SELECTABLE for dpll output pins
ice: fix memleak in ice_init_tx_topology()
ice: clear port vlan config during reset
ice: Fix improper handling of refcount in ice_sriov_set_msix_vec_count()
ice: Fix improper handling of refcount in ice_dpll_init_rclk_pins()
ice: set correct dst VSI in only LAN filters
====================
Link: https://patch.msgid.link/20240930223601.3137464-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The code seems to be handling EPROBE_DEFER explicitly and if there's no
error, enables the clock. clk_get_optional exists for that.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20240930211628.330703-1-rosenp@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use the netdev-genl interface to map NAPI instances to queues so that
this information is accessible to user programs via netlink.
$ ./tools/net/ynl/cli.py --spec Documentation/netlink/specs/netdev.yaml \
--dump queue-get --json='{"ifindex": 2}'
[{'id': 0, 'ifindex': 2, 'napi-id': 8313, 'type': 'rx'},
{'id': 1, 'ifindex': 2, 'napi-id': 8314, 'type': 'rx'},
{'id': 2, 'ifindex': 2, 'napi-id': 8315, 'type': 'rx'},
{'id': 3, 'ifindex': 2, 'napi-id': 8316, 'type': 'rx'},
{'id': 4, 'ifindex': 2, 'napi-id': 8317, 'type': 'rx'},
[...]
{'id': 0, 'ifindex': 2, 'napi-id': 8297, 'type': 'tx'},
{'id': 1, 'ifindex': 2, 'napi-id': 8298, 'type': 'tx'},
{'id': 2, 'ifindex': 2, 'napi-id': 8299, 'type': 'tx'},
{'id': 3, 'ifindex': 2, 'napi-id': 8300, 'type': 'tx'},
{'id': 4, 'ifindex': 2, 'napi-id': 8301, 'type': 'tx'},
[...]
Signed-off-by: Joe Damato <jdamato@fastly.com>
Reviewed-by: Praveen Kaligineedi <pkaligineedi@google.com>
Link: https://patch.msgid.link/20240930210731.1629-3-jdamato@fastly.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use netdev-genl interface to map IRQs to NAPI instances so that this
information is accessible by user apps via netlink.
$ cat /proc/interrupts | grep gve | grep -v mgmnt | cut -f1 --delimiter=':'
34
35
36
37
38
39
40
[...]
65
$ ./tools/net/ynl/cli.py --spec Documentation/netlink/specs/netdev.yaml \
--dump napi-get --json='{"ifindex": 2}'
[{'id': 8288, 'ifindex': 2, 'irq': 65},
[...]
{'id': 8263, 'ifindex': 2, 'irq': 40},
{'id': 8262, 'ifindex': 2, 'irq': 39},
{'id': 8261, 'ifindex': 2, 'irq': 38},
{'id': 8260, 'ifindex': 2, 'irq': 37},
{'id': 8259, 'ifindex': 2, 'irq': 36},
{'id': 8258, 'ifindex': 2, 'irq': 35},
{'id': 8257, 'ifindex': 2, 'irq': 34}]
Signed-off-by: Joe Damato <jdamato@fastly.com>
Reviewed-by: Praveen Kaligineedi <pkaligineedi@google.com>
Link: https://patch.msgid.link/20240930210731.1629-2-jdamato@fastly.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for link up and link down interrupts in lan887x.
Signed-off-by: Divya Koppera <divya.koppera@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Link: https://patch.msgid.link/20241001144421.6661-1-divya.koppera@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Pass a dscp_t variable to ip_route_input_noref(), instead of a plain
u8, to prevent accidental setting of ECN bits in ->flowi4_tos.
Callers of ip_route_input_noref() to consider are:
* arp_process() in net/ipv4/arp.c. This function sets the tos
parameter to 0, which is already a valid dscp_t value, so it
doesn't need to be adjusted for the new prototype.
* ip_route_input(), which already has a dscp_t variable to pass as
parameter. We just need to remove the inet_dscp_to_dsfield()
conversion.
* ipvlan_l3_rcv(), bpf_lwt_input_reroute(), ip_expire(),
ip_rcv_finish_core(), xfrm4_rcv_encap_finish() and
xfrm4_rcv_encap(), which get the DSCP directly from IPv4 headers
and can simply use the ip4h_dscp() helper.
While there, declare the IPv4 header pointers as const in
ipvlan_l3_rcv() and bpf_lwt_input_reroute().
Also, modify the declaration of ip_route_input_noref() in
include/net/route.h so that it matches the prototype of its
implementation in net/ipv4/route.c.
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://patch.msgid.link/a8a747bed452519c4d0cc06af32c7e7795d7b627.1727807926.git.gnault@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
