| Age | Commit message (Collapse) | Author |
|---|
|
Commit 7662abf4db94 ("net: phy: sfp: Add support for SMBus module access")
added SMBus access for SFP modules, but limited it to single-byte
transfers. As a side effect, hwmon is disabled (16-bit reads cannot be
guaranteed atomic) and a warning is printed.
Many SMBus-only I2C controllers in the wild support more than just
byte access, and SFP cages are often wired to such controllers
rather than to a full-featured I2C controller -- e.g. the SMBus
controllers in the Realtek longan and mango SoCs, which advertise
word access and I2C block reads. Today, they cannot drive an SFP at
all without falling back to the byte-only path.
Extend sfp_smbus_read()/sfp_smbus_write() so that, in addition to
the existing byte access, they also use SMBus word access and SMBus
I2C block access whenever the adapter advertises them. Both
directions are handled in a single read and a single write helper
that pick the largest supported transfer per chunk and fall back as
needed.
I2C-block is preferred unconditionally when available: the protocol
carries any length 1..32, so it can serve every chunk -- including
the 1- and 2-byte tails -- without help from word or byte access.
Note that this requires I2C_FUNC_SMBUS_I2C_BLOCK, which reads a
caller-specified number of bytes. This deviates from the official
SMBus Block Read (length is supplied by the slave) but is widely
supported by Linux I2C controllers/drivers.
Capability matrix this implementation supports:
- BYTE only: works (unchanged behaviour); 1-byte
xfers, hwmon disabled.
- BYTE + WORD: word for >=2-byte chunks, byte for
trailing odd byte.
- I2C_BLOCK present (with or
without BYTE/WORD): block as the universal transport for
every chunk.
- WORD only (no BYTE/BLOCK): accepted with WARN_ONCE. Even-length
transfers work; odd-length transfers
(e.g. the 3-byte cotsworks fixup
write) hit the BYTE branch which the
adapter does not implement, so the
xfer returns an error and the
operation is aborted. No mainline
I2C driver was found to advertise
WORD without BYTE; the warning lets
us learn about it if it ever shows
up.
Adapters with asymmetric R/W capabilities (e.g. only READ_I2C_BLOCK
but not WRITE_I2C_BLOCK) remain functionally correct -- the
per-iteration fallback uses the direction-specific bits -- but the
shared i2c_max_block_size is sized by the all-bits-set check, so a
transfer in the better-supported direction is not upgraded. None of
the mainline I2C bus drivers surveyed during review advertise such
asymmetry; promoting i2c_max_block_size to per-direction sizes can
be revisited if needed.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20260614133418.2068201-3-jelonek.jonas@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The SFP driver assumes all I2C adapters support reading and writing the
pre-defined block size SFP_EEPROM_BLOCK_SIZE of 16 bytes. This constant
was probably chosen based on good guesses and known limitations of a
range of I2C adapters and SFP modules.
However, I2C adapters may even support less and usually need to specify
this via I2C quirks. Theoretically, such an adapter may provide full
functionality but only support a read and write length of e.g. 8 bytes.
Currently, the SFP driver doesn't account for that.
Add handling for I2C quirks in SFP I2C configuration taking the fields
max_read_len and max_write_len in struct i2c_adapter_quirks into account
to further limit the maximum block size if needed.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20260614133418.2068201-2-jelonek.jonas@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
otx2vf_register_mbox_intr() currently installs the VF mailbox IRQ
handler before clearing stale mailbox interrupt state. The code then says
that local interrupt bits should be cleared first to avoid spurious
interrupts, but that clear still happens only after request_irq() has
already made the handler reachable.
A running system can reach this during VF mailbox interrupt registration
while stale or latched RVU_VF_INT state is still present. If delivery
happens in the request_irq()-to-clear window,
otx2vf_vfaf_mbox_intr_handler() can run before local quiesce and touch
the same vf->mbox and vf->mbox_wq carrier that probe and teardown later
reuse or destroy.
Move the stale mailbox interrupt clear ahead of request_irq(), but keep
interrupt enabling after the handler is installed. This closes the
pre-clear early-IRQ window without creating a new enable-before-handler
window.
Fixes: 3184fb5ba96e ("octeontx2-vf: Virtual function driver support")
Cc: stable@vger.kernel.org
Signed-off-by: Runyu Xiao <runyu.xiao@seu.edu.cn>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Ratheesh Kannoth <rkannoth@marvell.com>
Link: https://patch.msgid.link/20260611160014.3202224-3-runyu.xiao@seu.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
otx2_register_mbox_intr() currently installs the PF mailbox IRQ handler
before clearing stale mailbox interrupt state. The function itself then
comments that the local interrupt bits must be cleared first to avoid
spurious interrupts, but that clear happens only after request_irq() has
already exposed the handler to irq delivery.
A running system can reach this during PF mailbox interrupt registration
while stale or latched RVU_PF_INT state is still present. If delivery
happens in the request_irq()-to-clear window,
otx2_pfaf_mbox_intr_handler() can run before local quiesce and touch
the same pf->mbox and pf->mbox_wq carrier that probe and teardown later
reuse or destroy.
Move the stale mailbox interrupt clear ahead of request_irq(), but keep
interrupt enabling after the handler is installed. This closes the
pre-clear early-IRQ window without creating a new enable-before-handler
window.
Fixes: 5a6d7c9daef3 ("octeontx2-pf: Mailbox communication with AF")
Cc: stable@vger.kernel.org
Signed-off-by: Runyu Xiao <runyu.xiao@seu.edu.cn>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Ratheesh Kannoth <rkannoth@marvell.com>
Link: https://patch.msgid.link/20260611160014.3202224-2-runyu.xiao@seu.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
An SFP cage (compatible "sff,sfp") whose MOD_DEF0 signal is not wired to a
GPIO currently falls back to sff_gpio_get_state(), which unconditionally
reports the module as present. An empty cage therefore fails its probe and
is parked in SFP_MOD_ERROR forever; because SFP_F_PRESENT never deasserts
there is no REMOVE event to recover the state machine, so a module inserted
after boot is never detected, and empty cages spam -EIO at boot.
This affects boards that route none of the cage presence signal to a
software-readable input. On the NicGiga S100-0800S-M (RTL9303, 8x SFP+) the
cage I2C bus is the switch's SMBus master; TX_DISABLE is driven via a
PCA9534 I/O expander, but no MOD_ABS/MOD_DEF0 line reaches a readable GPIO
(the RTL9303 gpio0 lines read stuck-low, the single PCA9534 is fully
consumed by TX_DISABLE, and there is no RTL8231). The Horaco ZX-SW82TS-L2P
(RTL9302D, 2x SFP+) is independently affected in the same way.
For such an SFP cage, derive presence from a throttled single-byte I2C read
of the module EEPROM instead: a successful read asserts SFP_F_PRESENT,
R_PROBE_ABSENT consecutive failures clear it (to ride out a transient error
on a live module). The existing poll then emits SFP_E_INSERT / SFP_E_REMOVE
normally, giving working hot-plug and silencing the boot-time -EIO spam on
empty cages. Presence is re-probed every T_PROBE_PRESENT, so insertion is
detected within that interval and removal within
T_PROBE_PRESENT * R_PROBE_ABSENT.
A soldered-down module (compatible "sff,sff") has no presence signal and is
genuinely always present, so it continues to use sff_gpio_get_state(); the
new path is gated on the cage type advertising SFP_F_PRESENT.
Signed-off-by: Greg Patrick <gregspatrick@hotmail.com>
Tested-by: Manuel Stocker <mensi@mensi.ch>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20260611175341.2223184-1-gregspatrick@hotmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The devlink resource ID for ATU collides with the sentinel
DEVLINK_RESOURCE_ID_PARENT_TOP (0). As a result, ATU_bin_* are
registered as in fact registered as top-level siblings, not as children
of ATU.
Whether intentional or unintentional, clarify it by keeping the real
resource IDs starting at 1. Unfortunately ATU_bin_* are already
registered at top-level, so keep their parent to PARENT_TOP.
Signed-off-by: David Yang <mmyangfl@gmail.com>
Link: https://patch.msgid.link/20260611070856.889700-5-mmyangfl@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This might not cause real problems, but the hellcreek devlink resource
ID collides with the sentinel DEVLINK_RESOURCE_ID_PARENT_TOP (0). Avoid
it by keeping the real resource IDs starting at 1.
Signed-off-by: David Yang <mmyangfl@gmail.com>
Acked-by: Kurt Kanzenbach <kurt@linutronix.de>
Link: https://patch.msgid.link/20260611070856.889700-4-mmyangfl@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This might not cause real problems, but the b53 devlink resource ID
collides with the sentinel DEVLINK_RESOURCE_ID_PARENT_TOP (0). Avoid it
by keeping the real resource IDs starting at 1.
Signed-off-by: David Yang <mmyangfl@gmail.com>
Link: https://patch.msgid.link/20260611070856.889700-3-mmyangfl@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This might not cause real problems, but the dsa_loop devlink resource ID
collides with the sentinel DEVLINK_RESOURCE_ID_PARENT_TOP (0). Avoid it
by keeping the real resource IDs starting at 1.
Signed-off-by: David Yang <mmyangfl@gmail.com>
Link: https://patch.msgid.link/20260611070856.889700-2-mmyangfl@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
One fewer allocation for the priv struct.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Acked-by: Kurt Kanzenbach <kurt@linutronix.de>
Link: https://patch.msgid.link/20260608045640.5172-1-rosenp@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove the restriction blocking SD on embedded CPU PFs (ECPF), enabling
SD functionality on BlueField DPUs. Remove the blocker preventing SD
devices from transitioning to switchdev mode.
The infrastructure added in earlier patches properly handles this case.
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20260612113904.537595-16-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Allow SD devices to transition to switchdev before the SD group is
fully up. Metadata allocation requires the SD group to be ready, so
defer it from esw_offloads_enable() until SD shared-FDB activation.
Add mlx5_esw_offloads_init_deferred_metadata() which allocates per-vport
metadata and refreshes the ingress ACLs that were previously programmed
with metadata=0. The helper is idempotent and can be called multiple
times.
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20260612113904.537595-15-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
On an SD device, vport representors are not functional until the SD
group is combined and shared FDB is active. Skip the initial load and
the reload paths in that window; reps are loaded as part of the SD LAG
activation flow once it becomes active.
In addition, explicitly unload representors when SD LAG is destroyed.
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20260612113904.537595-14-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Enable MPESW LAG creation over SD LAG members, forming a composite LAG
hierarchy. This allows bonding multiple SD groups together under a
single MPESW configuration with shared FDB.
When enabling composite MPESW, the individual SD LAG shared FDB
configurations are temporarily torn down and recreated when the
composite LAG is disabled.
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20260612113904.537595-13-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
SD LAG is a virtual LAG without hardware LAG support, so it cannot use
the firmware vport LAG commands. Implement a software-based vport LAG
using egress ACL bounce rules.
Add esw_set_slave_egress_rule() to create an egress ACL rule on the
slave's manager vport that bounces traffic to the master's manager
vport. This achieves the same traffic steering as hardware vport LAG.
Redirect mlx5_cmd_create_vport_lag() and mlx5_cmd_destroy_vport_lag()
to the software implementation when operating in SD LAG mode.
In addition, adjust lag_demux creation to check SD LAG mode as well.
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20260612113904.537595-12-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Extend mlx5_lag_disable_change() to properly disable both regular LAG
and SD LAG when requested. Each LAG type uses its own devcom component
for locking.
Use mlx5_sd_get_devcom() helper to retrieve the SD devcom component,
needed for proper locking when disabling SD LAG.
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20260612113904.537595-11-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The lag demux resources (flow table, flow group, and rules xarray)
are stored on the shared ldev. With Socket Direct, multiple SD groups
each create their own demux FT/FG during their master's IB device
initialization. Since they all write to the same ldev fields, the
second group's init overwrites the first group's pointers, leaking
the first group's FT/FG.
During teardown, the cleanup uses the overwritten pointers, destroying
the wrong group's resources and leaving leaked flow tables in the LAG
namespace. These leaked tables can interfere with subsequently created
demux tables.
Move the demux resources from the shared ldev to per-master lag_func
instances. Each master device now owns its own independent demux
state. The rule_add and rule_del helpers look up the appropriate
master's lag_func via the existing filter/group infrastructure.
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20260612113904.537595-10-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When eswitch is disabled, notify the SD layer so it can clean up
SD-specific resources such as the TX flow table root configuration
on secondary devices.
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20260612113904.537595-9-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When the eswitch transitions, propagate the change to SD: secondaries
get their TX flow table root reconfigured for the new mode, and when
all group devices move to switchdev, the per-group shared FDB is
activated.
Shared FDB activation is best-effort - failure does not block the
eswitch transition; the next transition retries.
Note: the existing mlx5_get_sd() guard that blocks switchdev for SD
devices is intentionally retained. It will be removed once all
supporting patches are in place.
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20260612113904.537595-8-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In Socket Direct configurations the primary and secondary PFs share the
same native_port_num. The eswitch vport metadata encodes pf_num in its
upper bits to distinguish vports across PFs. Without SD-awareness, both
PFs generate identical metadata, causing FDB rules to steer traffic to
the wrong representor.
Add mlx5_sd_pf_num_get() which remaps the pf_num for SD devices.
Use it so each PF in an SD group produces unique vport metadata.
Signed-off-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20260612113904.537595-7-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add mlx5_fs_cmd_query_l2table_silent() to query the current silent mode
state from firmware. This allows detecting if firmware has already put
secondary devices into silent mode.
During SD group registration, query the silent mode of each device. If
a device is already in silent mode (set by firmware), record this in
the fw_silents_secondaries flag and use it to help determine the
primary/secondary roles.
When fw_silents_secondaries is set, skip the driver-initiated silent
mode set/unset operations since firmware manages this state. This
handles configurations where firmware persistently silences secondary
devices.
Signed-off-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20260612113904.537595-6-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Refactor SD group registration to use devcom event-driven role
determination to ensure SD is marked as ready only after roles are fully
assigned and the group state is consistent, making outside accessors,
which will be added in downstream patches, safe to use without races.
The devcom events:
- SD_PRIMARY_SET event: each device compares bus numbers with peers
to determine which should be primary
- SD_SECONDARIES_SET event: secondaries register themselves with the
elected primary device
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20260612113904.537595-5-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Some devcom events are not expected to fail. Rather than attempting
a rollback that may not be meaningful, allow callers to pass
DEVCOM_CANT_FAIL as the rollback_event to indicate that the event
handler should not fail. If it does, emit a warning and stop
propagating to further peers, but skip the rollback path.
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20260612113904.537595-4-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Factor mlx5_devcom_send_event() into two functions:
- mlx5_devcom_locked_send_event(): performs the dispatch (and
rollback) with comp->sem already held by the caller.
- mlx5_devcom_send_event(): unchanged wrapper that takes comp->sem,
calls the locked variant, and releases it.
This lets callers bracket multiple event broadcasts under a single
held write lock, eliminating the gap between consecutive dispatches
where peer state could change.
Will be used by a downstream patch.
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20260612113904.537595-3-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
SD secondary devices share the primary's uplink and do not have
their own uplink representor. When reloading IB reps on secondary
devices, skip the uplink and only load VF/SF vport IB reps.
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20260612113904.537595-2-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
gitolite.kernel.org:pub/scm/linux/kernel/git/tip/tip
Pull x86 cpuid updates from Ingo Molnar:
- CPUID API updates (Ahmed S. Darwish):
- Introduce a centralized CPUID parser
- Introduce a centralized CPUID data model
- Introduce <asm/cpuid/leaf_types.h>
- Rename cpuid_leaf()/cpuid_subleaf() APIs
- treewide: Explicitly include the x86 CPUID headers
- Update to x86-cpuid-db v3.1 (Maciej Wieczor-Retman)
- Continued removal of pre-i586 support and related simplifications
(Ingo Molnar)
- Add Intel CPU model number for rugged Panther Lake (Tony Luck)
- Misc fixes, updates and cleanups by Arnd Bergmann, Chao Gao, Lukas
Bulwahn, Sohil Mehta, Maciej Wieczor-Retman.
* tag 'x86-cpu-2026-06-14' of gitolite.kernel.org:pub/scm/linux/kernel/git/tip/tip: (25 commits)
x86/cpu: Make CONFIG_X86_CX8 unconditional
x86/cpu: Remove unused !CONFIG_X86_TSC code
x86/cpuid: Update bitfields to x86-cpuid-db v3.1
tools/x86/kcpuid: Update bitfields to x86-cpuid-db v3.1
x86/cpu: Make CONFIG_X86_TSC unconditional
MAINTAINERS: Drop obsolete FPU EMULATOR section
x86/cpu: Fix a F00F bug warning and clean up surrounding code
x86/cpu: Add Intel CPU model number for rugged Panther Lake
x86/cpuid: Introduce a centralized CPUID parser
x86/cpu: Introduce a centralized CPUID data model
x86/cpuid: Introduce <asm/cpuid/leaf_types.h>
x86/cpuid: Rename cpuid_leaf()/cpuid_subleaf() APIs
x86/cpu: Do not include the CPUID API header in asm/processor.h
Documentation: core-api/cpu_hotplug: Remove stale cpu0_hotplug docs
x86/cpu, cpufreq: Remove AMD ELAN support
x86/fpu: Remove the math-emu/ FPU emulation library
x86/fpu: Remove the 'no387' boot option
x86/fpu: Remove MATH_EMULATION and related glue code
treewide: Explicitly include the x86 CPUID headers
x86/cpu: Remove the CONFIG_X86_INVD_BUG quirk
...
|
|
gitolite.kernel.org:pub/scm/linux/kernel/git/tip/tip
Pull timekeeping updates from Thomas Gleixner:
"Updates for NTP/timekeeping and PTP:
- Expand timekeeping snapshot mechanisms
The various snapshot functions are mostly used for PTP to collect
"atomic" snapshots of various involved clocks.
They lack support for the recently introduced AUX clocks and do not
provide the underlying counter value (e.g. TSC) to user space.
Exposing the counter value snapshot allows for better control and
steering.
Convert the hard wired ktime_get_snapshot() to take a clock ID,
which allows the caller to select the clock ID to be captured along
with CLOCK_MONONOTONIC_RAW. Additionally capture the underlying
hardware counter value and the clock source ID of the counter.
Expand the hardware based snapshot capture where devices provide a
mechanism to snapshot the hardware PTP clock and the system counter
(usually via PCI/PTM) to support AUX clocks and also provide the
captured counter value back to the caller and not only the clock
timestamps derived from it.
- Add a new optional read_snapshot() callback to clocksources
That is required to capture atomic snapshots from clocksources
which are derived from TSC with a scaling mechanism (e.g. Hyper-V,
KVMclock).
The value pair is handed back in the snapshot structure to the
callers, so they can do the necessary correlations in a more
precise way.
This touches usage sites of the affected functions and data structure
all over the tree, but stays fully backwards compatible for the
existing user space exposed interfaces. New PTP IOCTLs will provide
access to the extended functionality in later kernel versions"
* tag 'timers-ptp-2026-06-13' of gitolite.kernel.org:pub/scm/linux/kernel/git/tip/tip: (28 commits)
ptp: vmclock: Use hw_cycles from snapshot for precise TSC pairing
x86/kvmclock: Implement read_snapshot() for kvmclock clocksource
clocksource/hyperv: Implement read_snapshot() for TSC page clocksource
timekeeping: Add clocksource read_snapshot() method and hw_cycles to snapshot
ptp: Switch to ktime_get_snapshot_id() for pre/post timestamps
timekeeping: Add support for AUX clock cross timestamping
timekeeping: Remove system_device_crosststamp::sys_realtime
ALSA: hda/common: Use system_device_crosststamp::sys_systime
wifi: iwlwifi: Use system_device_crosststamp::sys_systime
ptp: Use system_device_crosststamp::sys_systime
timekeeping: Prepare for cross timestamps on arbitrary clock IDs
timekeeping: Remove ktime_get_snapshot()
virtio_rtc: Use provided clock ID for history snapshot
net/mlx5: Use provided clock ID for history snapshot
igc: Use provided clock ID for history snapshot
ice/ptp: Use provided clock ID for history snapshot
wifi: iwlwifi: Adopt PTP cross timestamps to core changes
timekeeping: Add CLOCK ID to system_device_crosststamp
timekeeping: Add system_counterval_t to struct system_device_crosststamp
timekeeping: Add CLOCK_AUX support for ktime_get_snapshot_id()
...
|
|
gitolite.kernel.org:pub/scm/linux/kernel/git/driver-core/driver-core
Pull driver core updates from Danilo Krummrich:
"Deferred probe:
- Fix race where deferred probe timeout work could be permanently
canceled by using mod_delayed_work()
- Fix missing jiffies conversion in deferred_probe_extend_timeout()
- Guard timeout extension with delayed_work_pending() to prevent
premature firing
- Use system_percpu_wq instead of the deprecated system_wq
- Update deferred_probe_timeout documentation
device:
- Replace direct struct device bitfield access (can_match, dma_iommu,
dma_skip_sync, dma_ops_bypass, state_synced, dma_coherent,
of_node_reused, offline, offline_disabled) with flag-based
accessors using bit operations
- Reject devices with unregistered buses
- Delete unused DEVICE_ATTR_PREALLOC()
- Add low-level device attribute macros with const show/store
callbacks, allowing device attributes to reside in read-only memory
- Move core device attributes to read-only memory
- Constify group array pointers in driver_add_groups() /
driver_remove_groups(), struct bus_type, and struct device_driver
device property:
- Fix fwnode reference leak in fwnode_graph_get_endpoint_by_id()
- Initialize all fields of fwnode_handle in fwnode_init()
- Provide swnode_get()/swnode_put() wrappers around kobject_get/put()
- Allow passing struct software_node_ref_args pointers directly to
PROPERTY_ENTRY_REF()
driver_override:
- Migrate amba, cdx, vmbus, and rpmsg to the generic driver_override
infrastructure, fixing a UAF from unsynchronized access to
driver_override in bus match() callbacks
- Remove the now-unused driver_set_override()
firmware loader:
- Fix recursive lock deadlock in device_cache_fw_images() when async
work falls back to synchronous execution
- Fix device reference leak in firmware_upload_register()
platform:
- Pass KBUILD_MODNAME through the platform driver registration macro
to create module symlinks in sysfs for built-in drivers; move
module_kset initialization to a pure_initcall and tegra cbb
registration to core_initcall to ensure correct ordering
- Pass THIS_MODULE implicitly through a coresight_init_driver() macro
sysfs:
- Upgrade OOB write detection in sysfs_kf_seq_show() from printk to
WARN
- Add return value clamping to sysfs_kf_read()
Rust:
- ACPI:
Fix missing match data for PRP0001 by exporting
acpi_of_match_device()
- Auxiliary:
Replace drvdata() with dedicated registration data on
auxiliary_device. drvdata() exposed the driver's bus device private
data beyond the driver's own scope, creating ordering constraints
and forcing the data to outlive all registrations that access it.
Registration data is instead scoped structurally to the
Registration object, making lifecycle ordering enforced by
construction rather than convention.
- Rust-native device driver lifetimes (HRT):
Allow Rust device drivers to carry a lifetime parameter on their
bus device private data, tied to the device binding scope -- the
interval during which a bus device is bound to a driver. Device
resources like pci::Bar<'a> and IoMem<'a> can be stored directly in
the driver's bus device private data with a lifetime bounded by the
binding scope, so the compiler enforces at build time that they do
not outlive the binding. This removes Devres indirection from every
access site and eliminates try_access() failure paths in
destructors.
Bus driver traits use a Generic Associated Type (GAT) Data<'bound>
to introduce the lifetime on the private data, rather than
parameterizing the Driver trait itself. Auxiliary registration
data, where the lifetime is not introduced by a trait callback but
must be threaded through Registration, uses the ForLt trait (a
type-level abstraction for types generic over a lifetime).
Misc:
- Fix DT overlayed devices not probing by reverting the broken
treewide overlay fix and re-running fw_devlink consumer pickup when
an overlay is applied to a bound device
- Use root_device_register() for faux bus root device; add sanity
check for failed bus init
- Fix dev_has_sync_state() data race with READ_ONCE() and move it to
base.h
- Avoid spurious device_links warning when removing a device while
its supplier is unbinding
- Switch ISA bus to dynamic root device
- Fix suspicious RCU usage in kernfs_put()
- Remove devcoredump exit callback
- Constify devfreq_event_class"
* tag 'driver-core-7.2-rc1' of gitolite.kernel.org:pub/scm/linux/kernel/git/driver-core/driver-core: (81 commits)
software node: allow passing reference args to PROPERTY_ENTRY_REF()
driver core: platform: set mod_name in driver registration
coresight: pass THIS_MODULE implicitly through a macro
kernel: param: initialize module_kset in a pure_initcall
soc/tegra: cbb: Move driver registration from pure_initcall to core_initcall
firmware_loader: Fix recursive lock in device_cache_fw_images()
driver core: Use system_percpu_wq instead of system_wq
driver core: remove driver_set_override()
rpmsg: use generic driver_override infrastructure
Drivers: hv: vmbus: use generic driver_override infrastructure
cdx: use generic driver_override infrastructure
amba: use generic driver_override infrastructure
rust: devres: add 'static bound to Devres<T>
samples: rust: rust_driver_auxiliary: showcase lifetime-bound registration data
rust: auxiliary: generalize Registration over ForLt
rust: types: add `ForLt` trait for higher-ranked lifetime support
gpu: nova-core: separate driver type from driver data
samples: rust: rust_driver_pci: use HRT lifetime for Bar
rust: io: make IoMem and ExclusiveIoMem lifetime-parameterized
rust: pci: make Bar lifetime-parameterized
...
|
|
ath6kl_usb_create() currently creates ath6kl_wq with flags set to 0:
alloc_workqueue("ath6kl_wq", 0, 0)
This triggers a runtime warning in __alloc_workqueue() because the queue is
created with neither WQ_PERCPU nor WQ_UNBOUND set:
workqueue: ath6kl_wq is using neither WQ_PERCPU or WQ_UNBOUND.
Setting WQ_PERCPU.
Set WQ_PERCPU explicitly to match the actual execution model and remove the
warning during device probe. No functional change intended.
Fixes: 21c05ca88a54 ("workqueue: Add warnings and ensure one among WQ_PERCPU or WQ_UNBOUND is present")
Reported-by: syzbot+f80c62f371ba6a1e7d79@syzkaller.appspotmail.com
Link: https://lore.kernel.org/all/6a289c01.39669fcc.33b062.00aa.GAE@google.com/T/
Signed-off-by: wuyankun <wuyankun@uniontech.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
GRO_LEGACY_MAX_SIZE = 65536; total_len being 65536 is too big to fit
into a u16. As can be seen in skb_gro_receive, packets bigger or equal
to gro_max_size (or GRO_LEGACY_MAX_SIZE) are dropped with -E2BIG. Apply
the same boundary to geneve_post_decap_hint to avoid writing 65536 to a
16-bit iph->tot_len field with an overflow.
Fixes: fd0dd796576e ("geneve: use GRO hint option in the RX path")
Signed-off-by: Alice Mikityanska <alice@isovalent.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20260611192955.604661-3-alice.kernel@fastmail.im
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The hclge_main.c file has become very large,
so the fd code has been moved to a separate hclge_fd.c file.
This patch only moves the code and does not modify any functionality.
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Link: https://patch.msgid.link/20260610060618.834987-7-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, the tc tool only supports adding and deleting rules from
the driver but does not support querying rules from the driver.
This patch adds a rule dump file in debugfs to check whether the driver's
configuration matches the configuration issued by tc flow.
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Link: https://patch.msgid.link/20260610060618.834987-6-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, the driver does not support FLOW_DISSECTOR_KEY_IP and
FLOW_DISSECTOR_KEY_ENC_KEYID. But the hardware supports
ip_tos (FLOW_DISSECTOR_KEY_IP) and
outer_tun_vni (FLOW_DISSECTOR_KEY_ENC_KEYID).
This patch adds support for FLOW_DISSECTOR_KEY_IP and
FLOW_DISSECTOR_KEY_ENC_KEYID.
Additionally, since tc flow cannot effectively support
l2_user_def, l3_user_def, and l4_user_def,
this patch explicitly sets them to not be used.
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Link: https://patch.msgid.link/20260610060618.834987-5-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, the driver supports only one action:HCLGE_FD_ACTION_SELECT_TC.
This patch adds support for HCLGE_FD_ACTION_SELECT_QUEUE and
HCLGE_FD_ACTION_DROP_PACKET.
A rule can have only one action. Therefore, the driver intercepts rules
that have multiple actions or no action.
Note: The driver considers cls_flower->classid as an action:
HCLGE_FD_ACTION_SELECT_TC.
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Link: https://patch.msgid.link/20260610060618.834987-4-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, when the tc tool is used to set flow table rules, the IP address
and MAC address can be configured separately, for example, src_xx or dst_xx
can be configured separately.
Therefore, the driver needs to check whether the mask is all zero in
keys, such as FLOW_DISSECTOR_KEY_IPV4_ADDRS, FLOW_DISSECTOR_KEY_IPV6_ADDRS,
and FLOW_DISSECTOR_KEY_ETH_ADDRS.
If the mask is all zero, the tuple is not configured.
In this case, the driver adds the tuple to unused_tuple.
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Link: https://patch.msgid.link/20260610060618.834987-3-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove the tc parameter from the add_cls_flower() ops callback and
refactor action parsing to support future extensions for SELECT_QUEUE
and DROP_PACKET actions.
Changes:
* Remove the tc parameter from the add_cls_flower() callback signature.
* Extract TC-based action parsing into hclge_get_tc_flower_action().
* Move the dissector->used_keys check from hclge_parse_cls_flower() to
hclge_check_cls_flower(), and restrict ETH_ADDRS to
HCLGE_FD_MODE_DEPTH_2K_WIDTH_400B_STAGE_1 mode since hardware only
supports MAC matching there.
* Migrate error reporting from dev_err() to netlink extended ACK (extack).
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Link: https://patch.msgid.link/20260610060618.834987-2-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
For both the join and leave paths, the logic goes through the following
steps: determines which FDB should be used on a port after the current
changeupper change, populate the private port structures with the new
FDB and, if necessary, make as not used the old FDB.
Instead of having two distinct paths inside the
dpaa2_switch_port_set_fdb() for linking=true and linking=false, unify
them. This will hopefully help in making this function easier to read.
No behavior changes are expected.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://patch.msgid.link/20260610150912.1788482-6-ioana.ciornei@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Move the FDB selection for when a port leaves bridge into a new helper -
dpaa2_switch_fdb_for_leave(). This will hopefully make the
dpaa2_switch_port_set_fdb() function easier to read and follow. The new
helper only determines the FDB to be used, any updates into the private
port structure still gets done in the set_fdb() function.
No changes in the actual behavior are intended.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://patch.msgid.link/20260610150912.1788482-5-ioana.ciornei@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The dpaa2_switch_port_set_fdb() function handles the setup of the FDB
for both changeupper cases: join and leave. Move the code block which
handles the join path into a new helper - dpaa2_switch_fdb_for_join() -
with the hope that the entire function will become easier to read and
extend with other use cases in the future.
This new helper just determines and returns what FDB should be used for
a specific port, the cleanup of the old FDB and the actual setup in the
per port structure remains in the dpaa2_switch_port_set_fdb() function.
No changes in the actual behavior are intended.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://patch.msgid.link/20260610150912.1788482-4-ioana.ciornei@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The dpaa2_switch_port_set_fdb() function is hard to follow and
open-coding the in-use check into it makes it even harder to read.
Factor out that code block into a new helper -
dpaa2_switch_fdb_in_use_by_others().
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://patch.msgid.link/20260610150912.1788482-3-ioana.ciornei@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Since there dpaa2_switch_port_set_fdb() never fails and its return value
was never checked, change its prototype to return void.
Also, instead of determining if the DPAA2 port is joining or leaving an
upper based on the value of the 'bridge_dev' parameter, add the
'linking' parameter to explicitly specify the action.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://patch.msgid.link/20260610150912.1788482-2-ioana.ciornei@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix spelling errors in code comments:
- igc_diag.c: 'autonegotioation' -> 'autonegotiation'
- igc_main.c: 'revisons' -> 'revisions' (two occurrences)
Signed-off-by: Maximilian Pezzullo <maximilianpezzullo@gmail.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Joe Damato <joe@dama.to>
Tested-by: Avigail Dahan <avigailx.dahan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20260609213559.178657-16-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix spelling errors in code comments:
- e1000_nvm.c: 'likley' -> 'likely'
- e1000_mac.c: 'auto-negotitation' -> 'auto-negotiation'
- e1000_mbx.h: 'exra' -> 'extra'
- e1000_defines.h: 'Aserted' -> 'Asserted'
Signed-off-by: Maximilian Pezzullo <maximilianpezzullo@gmail.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Joe Damato <joe@dama.to>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20260609213559.178657-15-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
[Why]
In e1000_set_eeprom(), the eeprom_buff is allocated to hold a range of
words. However, only the boundary words (the first and the last) are
populated from the EEPROM if the write request is not word-aligned.
The words in the middle of the buffer remain uninitialized because they
are intended to be completely overwritten by the new data via memcpy().
The previous implementation had a loop that performed le16_to_cpus()
on the entire buffer. This resulted in endianness conversion being
performed on uninitialized memory for all interior words.
Fix this by converting the endianness only for the boundary words
immediately after they are successfully read from the EEPROM.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Co-developed-by: Iskhakov Daniil <dish@amicon.ru>
Signed-off-by: Iskhakov Daniil <dish@amicon.ru>
Signed-off-by: Agalakov Daniil <ade@amicon.ru>
Tested-by: Avigail Dahan <avigailx.dahan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20260609213559.178657-14-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
[Why]
In e1000_set_eeprom(), the eeprom_buff is allocated to hold a range of
words. However, only the boundary words (the first and the last) are
populated from the EEPROM if the write request is not word-aligned.
The words in the middle of the buffer remain uninitialized because they
are intended to be completely overwritten by the new data via memcpy().
The previous implementation had a loop that performed le16_to_cpus()
on the entire buffer. This resulted in endianness conversion being
performed on uninitialized memory for all interior words.
Fix this by converting the endianness only for the boundary words
immediately after they are successfully read from the EEPROM.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Co-developed-by: Iskhakov Daniil <dish@amicon.ru>
Signed-off-by: Iskhakov Daniil <dish@amicon.ru>
Signed-off-by: Agalakov Daniil <ade@amicon.ru>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20260609213559.178657-13-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The __napi_schedule_irqoff() macro is intended to bypass saving and
restoring IRQ state when scheduling is requested from an IRQ handler,
where hard interrupts are already disabled. Use this macro in all three
interrupt handlers.
This was tested on a system with an I218-V and MSI interrupts. Because
this is an optimization, I was interested in measuring the impact, so I
added ktime_get() time measurement to e1000_intr_msi and a print of the
last sample in the watchdog task. For each test case I ran a
bi-directional iperf3 to saturate the line. With some help from awk,
here are the statistics.
49 samples each, all units ns
previous: min 678 max 1265 mean 879.429 median 806 stddev 137.188
noirq: min 707 max 1165 mean 811.857 median 790 stddev 89.486
According to this informal comparison, the mean time to handle an
interrupt from start to finish is improved by about 8% under load.
Signed-off-by: Matt Vollrath <tactii@gmail.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Michal Cohen <michalx.cohen@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20260609213559.178657-12-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Replace napi_schedule() with napi_schedule_irqoff()
in the interrupt handler path in igc driver
Tested on Intel Corporation Ethernet Controller I226-V.
Suggested-by: Kohei Enju <kohei@enjuk.jp>
Signed-off-by: Daiki Harada <daiky0325@gmail.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Tested-by: Moriya Kadosh <moriyax.kadosh@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20260609213559.178657-11-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Replace napi_schedule() with napi_schedule_irqoff()
in the interrupt handler path in igb driver
Tested on QEMU with igb NIC emulation (-nic user,model=igb)
Suggested-by: Kohei Enju <kohei@enjuk.jp>
Signed-off-by: Daiki Harada <daiky0325@gmail.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20260609213559.178657-10-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Replace ktime_to_ns(ktime_get_real()) with the direct equivalent
ktime_get_real_ns() in e1000e_systim_reset(). Using the combined helper
avoids the unnecessary intermediate ktime_t variable and makes the
intent clearer.
Suggested-by: Jacob Keller <jacob.e.keller@intel.com>
Suggested-by: Simon Horman <horms@kernel.org>
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Avigail Dahan <avigailx.dahan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20260609213559.178657-9-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Replace ktime_to_ns(ktime_get_real()) with the direct equivalent
ktime_get_real_ns() and ktime_to_timespec64(ktime_get_real()) with
ktime_get_real_ts64() in igb_ptp_reset(). Using the combined helpers
makes the intent clearer.
Suggested-by: Jacob Keller <jacob.e.keller@intel.com>
Suggested-by: Simon Horman <horms@kernel.org>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20260609213559.178657-8-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
