| Age | Commit message (Collapse) | Author |
|---|
|
We have some policy via BIOS to block uses of 6 GHz. In this case, 6 GHz
sband will be NULL even if it is WiFi 7 chip. So, add NULL handling here
to avoid crash.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/20240412115729.8316-3-pkshih@realtek.com
|
|
TX power in MAC domain is signed 7 bits. (unit: based on txpwr_factor_mac)
The valid range should be [-64, 63].
While the original wrong bounds might not really be encountered, still make
them correct.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/20240412115729.8316-2-pkshih@realtek.com
|
|
firmware command
The DMA channel of firmware command doesn't use TX WD (WiFi descriptor), so
don't need to consider number of TX WD as factor of TX resource. Otherwise,
during pause state (a transient state to switch to/from low power mode)
firmware commands could be dropped and driver throws warnings suddenly:
rtw89_8852ce 0000:04:00.0: no tx fwcmd resource
rtw89_8852ce 0000:04:00.0: failed to send h2c
The case we met is that driver sends RSSI strength of firmware command at
RX path that could be running concurrently with switching low power mode.
The missing of this firmware command doesn't affect user experiences,
because the RSSI strength will be updated again after a while.
The DMA descriptors of normal packets has three layers like:
+-------+
| TX BD | (*n elements)
+-------+
|
| +-------+
+-> | TX WD | (*m elements)
+-------+
|
| +--------+
+-> | SKB |
+--------+
And, firmware command queue (TXCH 12) is a special queue that has only
two layers:
+-------+
| TX BD | (*n elements)
+-------+
|
| +------------------+
+-> | firmware command |
+------------------+
Fixes: 4a29213cd775 ("wifi: rtw89: pci: correct TX resource checking in low power mode")
Cc: stable@vger.kernel.org
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/20240410011316.9906-1-pkshih@realtek.com
|
|
ndo_get_phys_port_name is never actually used, as in switchdev
devlink is always being created.
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Dariusz Aftanski <dariusz.aftanski@linux.intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
In cases when VF sends malformed packets that are classified as malicious,
it can cause Tx queue to freeze as a result of Malicious Driver Detection
event. Such malformed packets can appear as a result of a faulty userspace
app running on VF. This frozen queue can be stuck for several minutes being
unusable.
User might prefer to immediately bring the VF back to operational state
after such event, which can be done by automatically resetting the VF which
caused MDD. This is already implemented for Rx events (mdd-auto-reset-vf
flag private flag needs to be set).
Extend the VF auto reset to also cover Tx MDD events. When any MDD event
occurs on VF (Tx or Rx) and the mdd-auto-reset-vf private flag is set,
perform a graceful VF reset to quickly bring it back to operational state.
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Co-developed-by: Liang-Min Wang <liang-min.wang@intel.com>
Signed-off-by: Liang-Min Wang <liang-min.wang@intel.com>
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The mediatek-ge PHY driver already disables EEE advertisement on the switch
PHYs but my testing [1] shows that it is somehow enabled afterwards.
Disabling EEE advertisement before the PHY driver initialises keeps it off.
Therefore, remove disabling EEE advertisement here as it's useless.
Link: https://lore.kernel.org/netdev/d286ea27-e911-4dcb-9037-b75f22b437b8@arinc9.com/ [1]
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The "MT7988A Wi-Fi 7 Generation Router Platform: Datasheet (Open Version)
v0.1" document shows bits 16 to 18 as the MIRROR_PORT field of the CPU
forward control register. Currently, the MT7530 DSA subdriver configures
bits 0 to 2 of the CPU forward control register which breaks the port
mirroring feature for the MT7988 SoC switch.
Fix this by using the MT7531_MIRROR_PORT_GET() and MT7531_MIRROR_PORT_SET()
macros which utilise the correct bits.
Fixes: 110c18bfed41 ("net: dsa: mt7530: introduce driver for MT7988 built-in switch")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Acked-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This switch intellectual property provides a bit on the ARL global control
register which controls allowing mirroring frames which are received on the
local port (monitor port). This bit is unset after reset.
This ability must be enabled to fully support the port mirroring feature on
this switch intellectual property.
Therefore, this patch fixes the traffic not being reflected on a port,
which would be configured like below:
tc qdisc add dev swp0 clsact
tc filter add dev swp0 ingress matchall skip_sw \
action mirred egress mirror dev swp0
As a side note, this configuration provides the hairpinning feature for a
single port.
Fixes: 37feab6076aa ("net: dsa: mt7530: add support for port mirroring")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This function is supposed to return a uid on success, and an errno in
failure.
But it currently returns the return value of the specific cmd version
handler, which in turn returns 0 on success and errno otherwise.
This means that on success, iwl_mvm_build_scan_cmd will return 0
regardless if the actual uid.
Fix this by returning the uid if the handler succeeded.
Fixes: 687db6ff5b70 ("iwlwifi: scan: make new scan req versioning flow")
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Link: https://msgid.link/20240415114847.5e2d602b3190.I4c4931021be74a67a869384c8f8ee7463e0c7857@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
If a PASN station is added, and an old PASN station already exists
for the same mac address, remove the old station before adding the
new one. Keeping the old station caueses old security context to
be used in measurements.
Fixes: 0739a7d70e00 ("iwlwifi: mvm: initiator: add option for adding a PASN responder")
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240415114847.ef3544a416f2.I4e8c7c8ca22737f4f908ae5cd4fc0b920c703dd3@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
pse_control_config
In commit 18ff0bcda6d1 ("ethtool: add interface to interact with Ethernet
Power Equipment"), the 'pse_control_config' structure was introduced,
housing a single member labeled 'admin_cotrol' responsible for maintaining
the operational state of the PoDL PSE functions.
A noticeable typographical error exists in the naming of this field
('cotrol' should be corrected to 'control'), which this commit aims to
rectify.
Furthermore, with upcoming extensions of this structure to encompass PoE
functionalities, the field is being renamed to 'podl_admin_state' to
distinctly indicate that this state is tailored specifically for PoDL."
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://lore.kernel.org/r/20240414-feature_poe-v8-3-e4bf1e860da5@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The print function dev_err() is redundant because
platform_get_irq_byname() already prints an error.
./drivers/net/ipa/ipa_interrupt.c:300:2-9: line 300 is redundant because platform_get_irq() already prints an error.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Closes: https://bugzilla.openanolis.cn/show_bug.cgi?id=8756
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240415031456.10805-1-jiapeng.chong@linux.alibaba.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
vhost_worker will call tun call backs to receive packets. If too many
illegal packets arrives, tun_do_read will keep dumping packet contents.
When console is enabled, it will costs much more cpu time to dump
packet and soft lockup will be detected.
net_ratelimit mechanism can be used to limit the dumping rate.
PID: 33036 TASK: ffff949da6f20000 CPU: 23 COMMAND: "vhost-32980"
#0 [fffffe00003fce50] crash_nmi_callback at ffffffff89249253
#1 [fffffe00003fce58] nmi_handle at ffffffff89225fa3
#2 [fffffe00003fceb0] default_do_nmi at ffffffff8922642e
#3 [fffffe00003fced0] do_nmi at ffffffff8922660d
#4 [fffffe00003fcef0] end_repeat_nmi at ffffffff89c01663
[exception RIP: io_serial_in+20]
RIP: ffffffff89792594 RSP: ffffa655314979e8 RFLAGS: 00000002
RAX: ffffffff89792500 RBX: ffffffff8af428a0 RCX: 0000000000000000
RDX: 00000000000003fd RSI: 0000000000000005 RDI: ffffffff8af428a0
RBP: 0000000000002710 R8: 0000000000000004 R9: 000000000000000f
R10: 0000000000000000 R11: ffffffff8acbf64f R12: 0000000000000020
R13: ffffffff8acbf698 R14: 0000000000000058 R15: 0000000000000000
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018
#5 [ffffa655314979e8] io_serial_in at ffffffff89792594
#6 [ffffa655314979e8] wait_for_xmitr at ffffffff89793470
#7 [ffffa65531497a08] serial8250_console_putchar at ffffffff897934f6
#8 [ffffa65531497a20] uart_console_write at ffffffff8978b605
#9 [ffffa65531497a48] serial8250_console_write at ffffffff89796558
#10 [ffffa65531497ac8] console_unlock at ffffffff89316124
#11 [ffffa65531497b10] vprintk_emit at ffffffff89317c07
#12 [ffffa65531497b68] printk at ffffffff89318306
#13 [ffffa65531497bc8] print_hex_dump at ffffffff89650765
#14 [ffffa65531497ca8] tun_do_read at ffffffffc0b06c27 [tun]
#15 [ffffa65531497d38] tun_recvmsg at ffffffffc0b06e34 [tun]
#16 [ffffa65531497d68] handle_rx at ffffffffc0c5d682 [vhost_net]
#17 [ffffa65531497ed0] vhost_worker at ffffffffc0c644dc [vhost]
#18 [ffffa65531497f10] kthread at ffffffff892d2e72
#19 [ffffa65531497f50] ret_from_fork at ffffffff89c0022f
Fixes: ef3db4a59542 ("tun: avoid BUG, dump packet on GSO errors")
Signed-off-by: Lei Chen <lei.chen@smartx.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Link: https://lore.kernel.org/r/20240415020247.2207781-1-lei.chen@smartx.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The ID table already has respective entry and MODULE_DEVICE_TABLE and
creates proper alias for SPI driver. Having another MODULE_ALIAS causes
the alias to be duplicated.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20240414154929.127045-1-krzk@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add missing FLOW_DISSECTOR_KEY_ENC_* checks to TC flower filter parsing.
Without these checks, it would be possible to add filters with tunnel
options on non-tunnel devices. enc_* options are only valid for tunnel
devices.
Example:
devlink dev eswitch set $PF1_PCI mode switchdev
echo 1 > /sys/class/net/$PF1/device/sriov_numvfs
tc qdisc add dev $VF1_PR ingress
ethtool -K $PF1 hw-tc-offload on
tc filter add dev $VF1_PR ingress flower enc_ttl 12 skip_sw action drop
Fixes: 9e300987d4a8 ("ice: VXLAN and Geneve TC support")
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The check for flags is done to not pass empty lookups to adding switch
rule functions. Since metadata is always added to lookups there is no
need to check against the flag.
It is also fixing the problem with such rule:
$ tc filter add dev gtp_dev ingress protocol ip prio 0 flower \
enc_dst_port 2123 action drop
Switch block in case of GTP can't parse the destination port, because it
should always be set to GTP specific value. The same with ethertype. The
result is that there is no other matching criteria than GTP tunnel. In
this case flags is 0, rule can't be added only because of defensive
check against flags.
Fixes: 9a225f81f540 ("ice: Support GTP-U and GTP-C offload in switchdev")
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
In case of traffic going from the VF (so ingress for port representor)
source VSI should be consider during packet classification. It is
needed for hardware to not match packets from different ports with
filters added on other port.
It is only for "from VF" traffic, because other traffic direction
doesn't have source VSI.
Set correct ::src_vsi in rule_info to pass it to the hardware filter.
For example this rule should drop only ipv4 packets from eth10, not from
the others VF PRs. It is needed to check source VSI in this case.
$tc filter add dev eth10 ingress protocol ip flower skip_sw action drop
Fixes: 0d08a441fb1a ("ice: ndo_setup_tc implementation for PF")
Reviewed-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Reviewed-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
wilc1000 driver currently uses SRCU API to manage vif list. There is no
real reason to use SRCU API here, and it makes things slightly more
complicated (we need to handle a SRCU index as well as a srcu_struct) than
classical RCU.
Switch SRCU APIs to RCU APIs.
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240410-wilc_srcu_to_rcu-v1-2-a9ff5b10feaa@bootlin.com
|
|
In order to prepare wilc1000 driver switch from SRCU to RCU, make sure that
allocators are provided with the GFP_ATOMIC flag when called in a critical
read section.
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240410-wilc_srcu_to_rcu-v1-1-a9ff5b10feaa@bootlin.com
|
|
Commit c3718936ec47 ("ipv6: anycast: complete RCU handling of struct
ifacaddr6") converted struct inet6_dev::ac_list to use RCU but missed that
ath11k also accesses this list. Now sparse warns:
drivers/net/wireless/ath/ath11k/mac.c:9145:21: warning: incorrect type in assignment (different address spaces)
drivers/net/wireless/ath/ath11k/mac.c:9145:21: expected struct ifacaddr6 *ifaca6
drivers/net/wireless/ath/ath11k/mac.c:9145:21: got struct ifacaddr6 [noderef] __rcu *ac_list
drivers/net/wireless/ath/ath11k/mac.c:9145:53: warning: incorrect type in assignment (different address spaces)
drivers/net/wireless/ath/ath11k/mac.c:9145:53: expected struct ifacaddr6 *ifaca6
drivers/net/wireless/ath/ath11k/mac.c:9145:53: got struct ifacaddr6 [noderef] __rcu *aca_next
Fix it by using rtnl_dereference(). Also add a note that read_lock_bh() calls
rcu_read_lock() which I was not aware of.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.37
Fixes: c3718936ec47 ("ipv6: anycast: complete RCU handling of struct ifacaddr6")
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240411165516.4070649-2-kvalo@kernel.org
|
|
Here is the list of the MAC capabilities specific to the particular DW MAC
IP-cores currently supported by the driver:
DW MAC100: MAC_ASYM_PAUSE | MAC_SYM_PAUSE |
MAC_10 | MAC_100
DW GMAC: MAC_ASYM_PAUSE | MAC_SYM_PAUSE |
MAC_10 | MAC_100 | MAC_1000
Allwinner sun8i MAC: MAC_ASYM_PAUSE | MAC_SYM_PAUSE |
MAC_10 | MAC_100 | MAC_1000
DW QoS Eth: MAC_ASYM_PAUSE | MAC_SYM_PAUSE |
MAC_10 | MAC_100 | MAC_1000 | MAC_2500FD
if there is more than 1 active Tx/Rx queues:
MAC_ASYM_PAUSE | MAC_SYM_PAUSE |
MAC_10FD | MAC_100FD | MAC_1000FD | MAC_2500FD
DW XGMAC: MAC_ASYM_PAUSE | MAC_SYM_PAUSE |
MAC_1000FD | MAC_2500FD | MAC_5000FD | MAC_10000FD
DW XLGMAC: MAC_ASYM_PAUSE | MAC_SYM_PAUSE |
MAC_1000FD | MAC_2500FD | MAC_5000FD | MAC_10000FD |
MAC_25000FD | MAC_40000FD | MAC_50000FD | MAC_100000FD
As you can see there are only two common capabilities:
MAC_ASYM_PAUSE | MAC_SYM_PAUSE.
Meanwhile what is currently implemented defines 10/100/1000 link speeds
for all IP-cores, which is definitely incorrect for DW MAC100, DW XGMAC
and DW XLGMAC devices.
Seeing the flow-control is implemented as a callback for each MAC IP-core
(see dwmac100_flow_ctrl(), dwmac1000_flow_ctrl(), sun8i_dwmac_flow_ctrl(),
etc) and since the MAC-specific setup() method is supposed to be called
for each available DW MAC-based device, the capabilities initialization
can be freely moved to these setup() functions, thus correctly setting up
the MAC-capabilities for each IP-core (including the Allwinner Sun8i). A
new stmmac_link::caps field was specifically introduced for that so to
have all link-specific info preserved in a single structure.
Note the suggested change fixes three earlier commits at a time. The
commit 5b0d7d7da64b ("net: stmmac: Add the missing speeds that XGMAC
supports") permitted the 10-100 link speeds and 1G half-duplex mode for DW
XGMAC IP-core even though it doesn't support them. The commit df7699c70c1b
("net: stmmac: Do not cut down 1G modes") incorrectly added the MAC1000
capability to the DW MAC100 IP-core. Similarly to the DW XGMAC the commit
8a880936e902 ("net: stmmac: Add XLGMII support") incorrectly permitted the
10-100 link speeds and 1G half-duplex mode for DW XLGMAC IP-core.
Fixes: 5b0d7d7da64b ("net: stmmac: Add the missing speeds that XGMAC supports")
Fixes: df7699c70c1b ("net: stmmac: Do not cut down 1G modes")
Fixes: 8a880936e902 ("net: stmmac: Add XLGMII support")
Suggested-by: Russell King (Oracle) <linux@armlinux.org.uk>
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Romain Gantois <romain.gantois@bootlin.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
It's possible to have the maximum link speed being artificially limited on
the platform-specific basis. It's done either by setting up the
plat_stmmacenet_data::max_speed field or by specifying the "max-speed"
DT-property. In such cases it's required that any specific
MAC-capabilities re-initializations would take the limit into account. In
particular the link speed capabilities may change during the number of
active Tx/Rx queues re-initialization. But the currently implemented
procedure doesn't take the speed limit into account.
Fix that by calling phylink_limit_mac_speed() in the
stmmac_reinit_queues() method if the speed limitation was required in the
same way as it's done in the stmmac_phy_setup() function.
Fixes: 95201f36f395 ("net: stmmac: update MAC capabilities when tx queues are updated")
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Romain Gantois <romain.gantois@bootlin.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
There are three DW MAC IP-cores which can have the multiple Tx/Rx queues
enabled:
DW GMAC v3.7+ with AV feature,
DW QoS Eth v4.x/v5.x,
DW XGMAC/XLGMAC
Based on the respective HW databooks, only the DW QoS Eth IP-core doesn't
support the half-duplex link mode in case if more than one queues enabled:
"In multiple queue/channel configurations, for half-duplex operation,
enable only the Q0/CH0 on Tx and Rx. For single queue/channel in
full-duplex operation, any queue/channel can be enabled."
The rest of the IP-cores don't have such constraint. Thus in order to have
the constraint applied for the DW QoS Eth MACs only, let's move the it'
implementation to the respective MAC-capabilities getter and make sure the
getter is called in the queues re-init procedure.
Fixes: b6cfffa7ad92 ("stmmac: fix DMA channel hang in half-duplex mode")
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Romain Gantois <romain.gantois@bootlin.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Tony Nguyen says:
====================
This series contains updates to ice driver only.
Lukasz removes unnecessary argument from ice_fdir_comp_rules().
Jakub adds support for ethtool 'ether' flow-type rules.
Jake moves setting of VF MSI-X value to initialization function and adds
tracking of VF relative MSI-X index.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
ice: store VF relative MSI-X index in q_vector->vf_reg_idx
ice: set vf->num_msix in ice_initialize_vf_entry()
ice: Implement 'flow-type ether' rules
ice: Remove unnecessary argument from ice_fdir_comp_rules()
====================
Link: https://lore.kernel.org/r/20240412210534.916756-1-anthony.l.nguyen@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Convert mt753x to provide its own phylink MAC operations, thus avoiding
the shim layer in DSA's port.c
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/E1rvIco-006bQu-Fq@rmk-PC.armlinux.org.uk
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Convert lantiq_gswip to provide its own phylink MAC operations, thus
avoiding the shim layer in DSA's port.c. For lantiq_gswip, it means
we end up with a common instance of phylink MAC operations that are
shared between the different variants, rather than having duplicated
initialisers in dsa_switch_ops.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1rvIcj-006bQo-B3@rmk-PC.armlinux.org.uk
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Convert qca8k to provide its own phylink MAC operations, thus
avoiding the shim layer in DSA's port.c.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/E1rvIce-006bQi-58@rmk-PC.armlinux.org.uk
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Convert ar9331 to provide its own phylink MAC operations, thus
avoiding the shim layer in DSA's port.c.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/E1rvIcZ-006bQc-0W@rmk-PC.armlinux.org.uk
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Convert sja1105 to provide its own phylink MAC operations, thus
avoiding the shim layer in DSA's port.c
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/E1rvIcT-006bQW-S3@rmk-PC.armlinux.org.uk
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Every time EHT Operation element changed, mac80211 will parse it and
extract the valid puncturing bitmap according to the bandwidth.
Current driver only update puncturing bitmap to firmware as vdev
parameter. Which can only meet the needs of AP. But STA will also use
it as peer parameter. If only update as vdev parameter, might cause
firmware crash. QCN9274 is the same.
So update bandwidth and puncturing bitmap as peer parameters once they
changed for STA. Then send them to the firmware by WMI event.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240408083047.22548-1-quic_kangyang@quicinc.com
|
|
Currently, in the rx error data path, mac id is extracted from the
last 64bits of MSDU end description tag for each entry received in
the WBM error ring. Then, each entry will be updated into the MSDU
list for further processing. The extracted mac id is valid when a
single MSDU is not fragmented and received in the WBM error ring.
In scenarios where the size of a single MSDU received exceeds the
descriptor buffer size, resulting in fragmented or spillover MSDU
entries into the WBM error ring. In this case, the extracted mac id
from each spillover entry is invalid except the last spillover entry
of the MSDU. This invalid mac id leads to packet rejection.
To address this issue, check if the MSDU continuation flag is set,
then extract the valid mac id from the last spillover entry.
Propagate the valid mac id to all the spillover entries of the single
MSDU in the temporary MSDU list(scatter_msdu_list). Then, update this
into the MSDU list (msdu_list) for further processing.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Nithyanantham Paramasivam <quic_nithp@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240404141538.1277258-1-quic_nithp@quicinc.com
|
|
Add very basic page pool use so that we can exercise
the netlink uAPI in a selftest.
Page pool gets created on open, destroyed on close.
But we control allocating of a single page thru debugfs.
This page may survive past the page pool itself so that
we can test orphaned page pools.
Link: https://lore.kernel.org/r/20240412141436.828666-2-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Pass the con_id instead of property so that callers won't repeat
the GPIO suffixes to try.
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
This patch adds XDP (eXpress Data Path) support to TI AM65 CPSW
Ethernet driver. The following features are implemented:
- NETDEV_XDP_ACT_BASIC (XDP_PASS, XDP_TX, XDP_DROP, XDP_ABORTED)
- NETDEV_XDP_ACT_REDIRECT (XDP_REDIRECT)
- NETDEV_XDP_ACT_NDO_XMIT (ndo_xdp_xmit callback)
The page pool memory model is used to get better performance.
Below are benchmark results obtained for the receiver with iperf3 default
parameters:
- Without page pool: 495 Mbits/sec
- With page pool: 605 Mbits/sec (actually 610 Mbits/sec, with a 5 Mbits/sec
loss due to extra processing in the hot path to handle XDP).
Signed-off-by: Julien Panis <jpanis@baylibre.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch introduces a member and the related accessors which can be
used to store descriptor specific additional information. This member
can store, for instance, an ID to differentiate a skb TX buffer type
from a xdpf TX buffer type.
Signed-off-by: Julien Panis <jpanis@baylibre.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds accessors for desc_size and cpumem members. They may be
used, for instance, to compute a descriptor index.
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Julien Panis <jpanis@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Upon reviewing the flower control flags handling in
this driver, I notice that the key wasn't being used,
only the mask.
Ie. `tc flower ... ip_flags nofrag` was hardware
offloaded as `... ip_flags frag`.
Only compile tested, no access to HW.
Fixes: c672e3727989 ("octeontx2-pf: Add support to filter packet based on IP fragment")
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
gve has supported software timestamp generation since its inception,
but has not advertised that support via ethtool. This patch correctly
advertises that support.
Signed-off-by: John Fraker <jfraker@google.com>
Reviewed-by: Harshitha Ramamurthy <hramamurthy@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add check for unsupported control flags.
Only compile-tested, no access to HW.
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add check for unsupported control flags.
Only compile-tested, no access to HW.
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use flow_rule_is_supp_control_flags()
Check the mask, not the key, for unsupported control flags.
Only compile-tested, no access to HW
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When disabling aRFS under the `priv->state_lock`, any scheduled
aRFS works are canceled using the `cancel_work_sync` function,
which waits for the work to end if it has already started.
However, while waiting for the work handler, the handler will
try to acquire the `state_lock` which is already acquired.
The worker acquires the lock to delete the rules if the state
is down, which is not the worker's responsibility since
disabling aRFS deletes the rules.
Add an aRFS state variable, which indicates whether the aRFS is
enabled and prevent adding rules when the aRFS is disabled.
Kernel log:
======================================================
WARNING: possible circular locking dependency detected
6.7.0-rc4_net_next_mlx5_5483eb2 #1 Tainted: G I
------------------------------------------------------
ethtool/386089 is trying to acquire lock:
ffff88810f21ce68 ((work_completion)(&rule->arfs_work)){+.+.}-{0:0}, at: __flush_work+0x74/0x4e0
but task is already holding lock:
ffff8884a1808cc0 (&priv->state_lock){+.+.}-{3:3}, at: mlx5e_ethtool_set_channels+0x53/0x200 [mlx5_core]
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&priv->state_lock){+.+.}-{3:3}:
__mutex_lock+0x80/0xc90
arfs_handle_work+0x4b/0x3b0 [mlx5_core]
process_one_work+0x1dc/0x4a0
worker_thread+0x1bf/0x3c0
kthread+0xd7/0x100
ret_from_fork+0x2d/0x50
ret_from_fork_asm+0x11/0x20
-> #0 ((work_completion)(&rule->arfs_work)){+.+.}-{0:0}:
__lock_acquire+0x17b4/0x2c80
lock_acquire+0xd0/0x2b0
__flush_work+0x7a/0x4e0
__cancel_work_timer+0x131/0x1c0
arfs_del_rules+0x143/0x1e0 [mlx5_core]
mlx5e_arfs_disable+0x1b/0x30 [mlx5_core]
mlx5e_ethtool_set_channels+0xcb/0x200 [mlx5_core]
ethnl_set_channels+0x28f/0x3b0
ethnl_default_set_doit+0xec/0x240
genl_family_rcv_msg_doit+0xd0/0x120
genl_rcv_msg+0x188/0x2c0
netlink_rcv_skb+0x54/0x100
genl_rcv+0x24/0x40
netlink_unicast+0x1a1/0x270
netlink_sendmsg+0x214/0x460
__sock_sendmsg+0x38/0x60
__sys_sendto+0x113/0x170
__x64_sys_sendto+0x20/0x30
do_syscall_64+0x40/0xe0
entry_SYSCALL_64_after_hwframe+0x46/0x4e
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&priv->state_lock);
lock((work_completion)(&rule->arfs_work));
lock(&priv->state_lock);
lock((work_completion)(&rule->arfs_work));
*** DEADLOCK ***
3 locks held by ethtool/386089:
#0: ffffffff82ea7210 (cb_lock){++++}-{3:3}, at: genl_rcv+0x15/0x40
#1: ffffffff82e94c88 (rtnl_mutex){+.+.}-{3:3}, at: ethnl_default_set_doit+0xd3/0x240
#2: ffff8884a1808cc0 (&priv->state_lock){+.+.}-{3:3}, at: mlx5e_ethtool_set_channels+0x53/0x200 [mlx5_core]
stack backtrace:
CPU: 15 PID: 386089 Comm: ethtool Tainted: G I 6.7.0-rc4_net_next_mlx5_5483eb2 #1
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
Call Trace:
<TASK>
dump_stack_lvl+0x60/0xa0
check_noncircular+0x144/0x160
__lock_acquire+0x17b4/0x2c80
lock_acquire+0xd0/0x2b0
? __flush_work+0x74/0x4e0
? save_trace+0x3e/0x360
? __flush_work+0x74/0x4e0
__flush_work+0x7a/0x4e0
? __flush_work+0x74/0x4e0
? __lock_acquire+0xa78/0x2c80
? lock_acquire+0xd0/0x2b0
? mark_held_locks+0x49/0x70
__cancel_work_timer+0x131/0x1c0
? mark_held_locks+0x49/0x70
arfs_del_rules+0x143/0x1e0 [mlx5_core]
mlx5e_arfs_disable+0x1b/0x30 [mlx5_core]
mlx5e_ethtool_set_channels+0xcb/0x200 [mlx5_core]
ethnl_set_channels+0x28f/0x3b0
ethnl_default_set_doit+0xec/0x240
genl_family_rcv_msg_doit+0xd0/0x120
genl_rcv_msg+0x188/0x2c0
? ethnl_ops_begin+0xb0/0xb0
? genl_family_rcv_msg_dumpit+0xf0/0xf0
netlink_rcv_skb+0x54/0x100
genl_rcv+0x24/0x40
netlink_unicast+0x1a1/0x270
netlink_sendmsg+0x214/0x460
__sock_sendmsg+0x38/0x60
__sys_sendto+0x113/0x170
? do_user_addr_fault+0x53f/0x8f0
__x64_sys_sendto+0x20/0x30
do_syscall_64+0x40/0xe0
entry_SYSCALL_64_after_hwframe+0x46/0x4e
</TASK>
Fixes: 45bf454ae884 ("net/mlx5e: Enabling aRFS mechanism")
Signed-off-by: Carolina Jubran <cjubran@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20240411115444.374475-7-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
netif_queue_set_napi asserts whether RTNL lock is held if
the netdev is initialized.
Acquire the RTNL lock before activating or deactivating
RQs/SQs if the lock has not been held before in the flow.
Fixes: f25e7b82635f ("net/mlx5e: link NAPI instances to queues and IRQs")
Cc: Joe Damato <jdamato@fastly.com>
Signed-off-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20240411115444.374475-6-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
coalescing
Channels can potentially have independent mdev instances. Do not refer to
the global mdev instance in the mlx5e_priv instance for channel FW
operations related to coalescing. CQ numbers that would be valid on the
channel's mdev instance may not be correctly referenced if using the
mlx5e_priv instance.
Fixes: 67936e138586 ("net/mlx5e: Let channels be SD-aware")
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20240411115444.374475-5-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Code parts from cited commit were mistakenly dropped while rebasing
before submission. Add them here.
Fixes: c6e77aa9dd82 ("net/mlx5: Register devlink first under devlink lock")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20240411115444.374475-4-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Check if devcom holds an error pointer and return immediately.
This fixes Smatch static checker warning:
drivers/net/ethernet/mellanox/mlx5/core/lib/sd.c:221 sd_register()
error: 'devcom' dereferencing possible ERR_PTR()
Enhance mlx5_devcom_register_component() so it stops returning NULL,
making it easier for its callers.
Fixes: d3d057666090 ("net/mlx5: SD, Implement devcom communication and primary election")
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/all/f09666c8-e604-41f6-958b-4cc55c73faf9@gmail.com/T/
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Link: https://lore.kernel.org/r/20240411115444.374475-3-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The cited patch introduces the concept of buckets in LAG in hash mode.
However, the patch doesn't clear the number of buckets in the LAG
deactivation. This results in using the wrong number of buckets in
case user create a hash mode LAG and afterwards create a non-hash
mode LAG.
Hence, restore buckets number to default after hash mode LAG
deactivation.
Fixes: 352899f384d4 ("net/mlx5: Lag, use buckets in hash mode")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Maor Gottlieb <maorg@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20240411115444.374475-2-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
I noticed that only 3 out of the 4 input bits were used,
mt.key->flags & FLOW_DIS_IS_FRAGMENT was never checked.
In order to avoid a complicated maze, I converted it to
use a 16 byte mapping table.
As shown in the table below the old heuristics doesn't
always do the right thing, ie. when FLOW_DIS_IS_FRAGMENT=1/1
then it used to only match follow-up fragment packets.
Here are all the combinations, and their resulting new/old
VCAP key/mask filter:
/- FLOW_DIS_IS_FRAGMENT (key/mask)
| /- FLOW_DIS_FIRST_FRAG (key/mask)
| | /-- new VCAP fragment (key/mask)
v v v v- old VCAP fragment (key/mask)
0/0 0/0 -/- -/- impossible (due to entry cond. on mask)
0/0 0/1 -/- 0/3 !! invalid (can't match non-fragment + follow-up frag)
0/0 1/0 -/- -/- impossible (key > mask)
0/0 1/1 1/3 1/3 first fragment
0/1 0/0 0/3 3/3 !! not fragmented
0/1 0/1 0/3 3/3 !! not fragmented (+ not first fragment)
0/1 1/0 -/- -/- impossible (key > mask)
0/1 1/1 -/- 1/3 !! invalid (non-fragment and first frag)
1/0 0/0 -/- -/- impossible (key > mask)
1/0 0/1 -/- -/- impossible (key > mask)
1/0 1/0 -/- -/- impossible (key > mask)
1/0 1/1 -/- -/- impossible (key > mask)
1/1 0/0 1/1 3/3 !! some fragment
1/1 0/1 3/3 3/3 follow-up fragment
1/1 1/0 -/- -/- impossible (key > mask)
1/1 1/1 1/3 1/3 first fragment
In the datasheet the VCAP fragment values are documented as:
0 = no fragment
1 = initial fragment
2 = suspicious fragment
3 = valid follow-up fragment
Result: 3 combinations match the old behavior,
3 combinations have been corrected,
2 combinations are now invalid, and fail,
8 combinations are impossible.
It should now be aligned with how FLOW_DIS_IS_FRAGMENT
and FLOW_DIS_FIRST_FRAG is set in __skb_flow_dissect() in
net/core/flow_dissector.c
Since the VCAP fragment values are not a bitfield, we have
to ignore the suspicious fragment value, eg. when matching
on any kind of fragment with FLOW_DIS_IS_FRAGMENT=1/1.
Only compile tested, and logic tested in userspace, as I
unfortunately don't have access to this switch chip (yet).
Fixes: d6c2964db3fe ("net: microchip: sparx5: Adding more tc flower keys for the IS2 VCAP")
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Tested-by: Daniel Machon <daniel.machon@microchip.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20240411111321.114095-1-ast@fiberby.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support to query scc version by devlink info for device V3.
Signed-off-by: Hao Chen <chenhao418@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Link: https://lore.kernel.org/r/20240410125354.2177067-5-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When the driver received an interrupte for hardware error,
it will try to restore by resetting. But the hardware registers
will also be reset at this case, which make it hard to analysis
why the hardware error occurs.
This patch dumps these registers before resetting to help
analyze the hardware error occurs.
Signed-off-by: Peiyang Wang <wangpeiyang1@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240410125354.2177067-4-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
