| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2024-04-03 (ice, idpf)
This series contains updates to ice and idpf drivers.
Dan Carpenter initializes some pointer declarations to NULL as needed for
resource cleanup on ice driver.
Petr Oros corrects assignment of VLAN operators to fix Rx VLAN filtering
in legacy mode for ice.
Joshua calls eth_type_trans() on unknown packets to prevent possible
kernel panic on idpf.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
idpf: fix kernel panic on unknown packet types
ice: fix enabling RX VLAN filtering
ice: Fix freeing uninitialized pointers
====================
Link: https://lore.kernel.org/r/20240403201929.1945116-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
After the commit d2689b6a86b9 ("net: usb: ax88179_178a: avoid two
consecutive device resets"), reset is not executed from bind operation and
mac address is not read from the device registers or the devicetree at that
moment. Since the check to configure if the assigned mac address is random
or not for the interface, happens after the bind operation from
usbnet_probe, the interface keeps configured as random address, although the
address is correctly read and set during open operation (the only reset
now).
In order to keep only one reset for the device and to avoid the interface
always configured as random address, after reset, configure correctly the
suitable field from the driver, if the mac address is read successfully from
the device registers or the devicetree. Take into account if a locally
administered address (random) was previously stored.
cc: stable@vger.kernel.org # 6.6+
Fixes: d2689b6a86b9 ("net: usb: ax88179_178a: avoid two consecutive device resets")
Reported-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Jose Ignacio Tornos Martinez <jtornosm@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240403132158.344838-1-jtornosm@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Some chips may not allow changing default speed when dual rate
transceivers modules are used. Firmware on those chips will
indicate the same to the driver.
Add a warning message when speed change is not supported
because a dual rate transceiver is detected by the NIC.
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/20240402093753.331120-8-pavan.chebbi@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This updated interface supports backing store APIs to
configure host FW trace buffers, updates transceivers ID
types, updates to TrueFlow features and other changes
for the basic L2 features.
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/20240402093753.331120-7-pavan.chebbi@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
- Change the last arg to xdp_prepare_buff to true from false.
- Ensure that when XDP_PASS is returned the xdp->data_meta area
is copied to the skb->data area. Account for the meta data
size on skb allocation and do a pull after to move it to the
"reserved" zone.
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Jesper Dangaard Brouer <hawk@kernel.org>
Cc: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/20240402093753.331120-6-pavan.chebbi@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Change bnxt_rx_xdp() to take a pointer to xdp instead of stack
variable.
This is in prepartion for the XDP metadata patch change where
the BPF program can change the value of the xdp.meta_data.
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Jesper Dangaard Brouer <hawk@kernel.org>
Cc: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/20240402093753.331120-5-pavan.chebbi@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Driver's Page Pool allocation code looks at the node local
to the PCIe device to determine where to allocate memory.
In scenarios where the core count per NUMA node is low (< default rings)
it makes sense to exhaust page pool allocations on
Node 0 first and then moving on to allocating page pools
for the remaining rings from Node 1.
With this patch, and the following configuration on the NIC
$ ethtool -L ens1f0np0 combined 16
(core count/node = 12, first 12 rings on node#0, last 4 rings node#1)
and traffic redirected to a ring on node#1 , we see a performance
improvement of ~20%
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/20240402093753.331120-4-pavan.chebbi@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Enable XPS on default during NIC open. The choice of
Tx queue is based on the CPU executing the thread that
submits the Tx request. The pool of Tx queues will be
spread evenly across both device-attached NUMA nodes(local)
and remote NUMA nodes.
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/20240402093753.331120-3-pavan.chebbi@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In case of DPC, after issuing the hot reset, the
kernel waits for 100ms for the device to complete
the reset. However on some older chips, the firmware
may take up to 1 second to complete the reset, only
after which the driver can restart the card.
Introduce delay of 900ms to handle this scenario on
the older chipsets.
Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/20240402093753.331120-2-pavan.chebbi@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
re-rereading it
In mtk_flow_entry_update_l2, the hwe->ib1 is read using READ_ONCE at the
beginning of the function, checked, and then re-read from hwe->ib1,
may void all guarantees of the checks. Reuse the value that was read by
READ_ONCE to ensure the consistency of the ib1 throughout the function.
Signed-off-by: linke li <lilinke99@qq.com>
Link: https://lore.kernel.org/r/tencent_C699E9540505523424F11A9BD3D21B86840A@qq.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The definition and declaration of sja1110_pcs_mdio_write_c45() don't have
parameters in the same order.
Knowing that sja1110_pcs_mdio_write_c45() is used as a function pointer
in 'sja1105_info' structure with .pcs_mdio_write_c45, and that we have:
int (*pcs_mdio_write_c45)(struct mii_bus *bus, int phy, int mmd,
int reg, u16 val);
it is likely that the definition is the one to change.
Found with cppcheck, funcArgOrderDifferent.
Fixes: ae271547bba6 ("net: dsa: sja1105: C45 only transactions for PCS")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Michael Walle <mwalle@kernel.org>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/ff2a5af67361988b3581831f7bd1eddebfb4c48f.1712082763.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The error statistics should be updated each time the poll function is
called, even if the full RX work budget has been consumed. This prevents
the counts from becoming stuck when RX bandwidth usage is high.
This also ensures that error counters are not updated after we've
re-enabled interrupts as that could result in a race condition.
Also drop an unnecessary space.
Fixes: c156633f1353 ("Renesas Ethernet AVB driver proper")
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/20240402145305.82148-2-paul.barker.ct@bp.renesas.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The TX queue should be serviced each time the poll function is called,
even if the full RX work budget has been consumed. This prevents
starvation of the TX queue when RX bandwidth usage is high.
Fixes: c156633f1353 ("Renesas Ethernet AVB driver proper")
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/20240402145305.82148-1-paul.barker.ct@bp.renesas.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
This driver's initialization functions do not perform any custom code,
except printing messages. Printing messages on modules
loading/unloading is discouraged because it pollutes the dmesg
regardless whether user actually has this device. Core kernel code
already gives tools to investigate whether module was loaded or not.
Drop the printing messages which allows to replace open-coded
module_sdio_driver().
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240329171019.63836-2-krzysztof.kozlowski@linaro.org
|
|
and avoid -Wfamnae warning
Prepare for the coming implementation by GCC and Clang of the
__counted_by attribute. Flexible array members annotated with
__counted_by can have their accesses bounds-checked at run-time
via CONFIG_UBSAN_BOUNDS (for array indexing) and CONFIG_FORTIFY_SOURCE
(for strcpy/memcpy-family functions).
Also, -Wflex-array-member-not-at-end is coming in GCC-14, and we are
getting ready to enable it globally.
So, use the `DEFINE_FLEX()` helper for an on-stack definition of
a flexible structure where the size of the flexible-array member
is known at compile-time, and refactor the rest of the code,
accordingly.
So, with these changes, fix the following warning:
drivers/net/wireless/ath/wil6210/wmi.c:4018:49: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
Link: https://github.com/KSPP/linux/issues/202
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/ZgSTCmdP+omePvWg@neat
|
|
avoid some -Wfamnae warnings
Prepare for the coming implementation by GCC and Clang of the
__counted_by attribute. Flexible array members annotated with
__counted_by can have their accesses bounds-checked at run-time
via CONFIG_UBSAN_BOUNDS (for array indexing) and CONFIG_FORTIFY_SOURCE
(for strcpy/memcpy-family functions).
Also, -Wflex-array-member-not-at-end is coming in GCC-14, and we are
getting ready to enable it globally.
So, use the `DEFINE_FLEX()` helper for an on-stack definition of
a flexible structure where the size of the flexible-array member
is known at compile-time, and refactor the rest of the code,
accordingly.
So, with these changes, fix the following warning:
drivers/net/wireless/ath/wil6210/cfg80211.c:896:43: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
Link: https://github.com/KSPP/linux/issues/202
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/ZgSP/CMSVfr68R2u@neat
|
|
kernel-doc flagged the following issue, so fix it:
drivers/net/wireless/ath/ath12k/hal.h:771: warning: missing initial short description on line:
* enum hal_rx_buf_return_buf_manager
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240329-hal_rx_buf_return_buf_manager-v1-2-e62ec9dc2af9@quicinc.com
|
|
kernel-doc flagged the following issue, so fix it:
drivers/net/wireless/ath/ath11k/hal.h:668: warning: missing initial short description on line:
* enum hal_rx_buf_return_buf_manager
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240329-hal_rx_buf_return_buf_manager-v1-1-e62ec9dc2af9@quicinc.com
|
|
gcc-9 and some other older versions produce a false-positive warning
for zeroing two fields
In file included from include/linux/string.h:369,
from drivers/net/wireless/ath/ath9k/main.c:18:
In function 'fortify_memset_chk',
inlined from 'ath9k_ps_wakeup' at drivers/net/wireless/ath/ath9k/main.c:140:3:
include/linux/fortify-string.h:462:25: error: call to '__write_overflow_field' declared with attribute warning: detected write beyond size of field (1st parameter); maybe use struct_group()? [-Werror=attribute-warning]
462 | __write_overflow_field(p_size_field, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Using a struct_group seems to reliably avoid the warning and
not make the code much uglier. The combined memset() should even
save a couple of cpu cycles.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240328135509.3755090-3-arnd@kernel.org
|
|
The carl9170_tx_release() function sometimes triggers a fortified-memset
warning in my randconfig builds:
In file included from include/linux/string.h:254,
from drivers/net/wireless/ath/carl9170/tx.c:40:
In function 'fortify_memset_chk',
inlined from 'carl9170_tx_release' at drivers/net/wireless/ath/carl9170/tx.c:283:2,
inlined from 'kref_put' at include/linux/kref.h:65:3,
inlined from 'carl9170_tx_put_skb' at drivers/net/wireless/ath/carl9170/tx.c:342:9:
include/linux/fortify-string.h:493:25: error: call to '__write_overflow_field' declared with attribute warning: detected write beyond size of field (1st parameter); maybe use struct_group()? [-Werror=attribute-warning]
493 | __write_overflow_field(p_size_field, size);
Kees previously tried to avoid this by using memset_after(), but it seems
this does not fully address the problem. I noticed that the memset_after()
here is done on a different part of the union (status) than the original
cast was from (rate_driver_data), which may confuse the compiler.
Unfortunately, the memset_after() trick does not work on driver_rates[]
because that is part of an anonymous struct, and I could not get
struct_group() to do this either. Using two separate memset() calls
on the two members does address the warning though.
Fixes: fb5f6a0e8063b ("mac80211: Use memset_after() to clear tx status")
Link: https://lore.kernel.org/lkml/20230623152443.2296825-1-arnd@kernel.org/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240328135509.3755090-2-arnd@kernel.org
|
|
The WMI commands are in little endian byte order, fix missing endianness
conversion in wmi_vdev_create_cmd.
Tested-on: WCN7850 hw2.0 WLAN.IOE_HMT.1.0.2-00240-QCAHMTSWPL_V1.0_V2.0_SILICON-1
Signed-off-by: Miaoqing Pan <quic_miaoqing@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240322003726.2016208-1-quic_miaoqing@quicinc.com
|
|
Create dfs_simulate_radar debugfs in ath12k debugfs directory.
Usage:
echo 1 > /sys/kernel/debug/ath12k/pci-0000:06:00.0/mac0/dfs_simulate_radar
This debugfs helps user to simulate RADAR interference in run time.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240320171305.655288-3-quic_rgnanase@quicinc.com
|
|
The initial debugfs infra bringup in ath12k driver and create the ath12k debugfs
and soc-specific directories in /sys/kernel/debug/
For each ath12k device, directory will be created in <bus>-<devname>
schema under ath12k root directory.
Example with one ath12k device:
/sys/kernel/debug/ath12k/pci-0000:06:00.0
ath12k
`-- pci-0000:06:00.0
|-- mac0
To enable ath12k debugfs support (CONFIG_ATH12K_DEBUGFS=y)
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Ramasamy Kaliappan <quic_rkaliapp@quicinc.com>
Signed-off-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240320171305.655288-2-quic_rgnanase@quicinc.com
|
|
Core in sdio_register_driver() already sets the .owner, so driver does
not need to.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20240403-module-owner-sdio-v2-7-ae46d6b955eb@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Core in sdio_register_driver() already sets the .owner, so driver does
not need to.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Kalle Valo <kvalo@kernel.org>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://lore.kernel.org/r/20240403-module-owner-sdio-v2-6-ae46d6b955eb@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Core in sdio_register_driver() already sets the .owner, so driver does
not need to.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Link: https://lore.kernel.org/r/20240403-module-owner-sdio-v2-5-ae46d6b955eb@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Core in sdio_register_driver() already sets the .owner, so driver does
not need to.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://lore.kernel.org/r/20240403-module-owner-sdio-v2-4-ae46d6b955eb@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
This driver's initialization functions do not perform any custom code,
except printing messages. Printing messages on modules
loading/unloading is discouraged because it pollutes the dmesg
regardless whether user actually has this device. Core kernel code
already gives tools to investigate whether module was loaded or not.
Drop the printing messages which allows to replace open-coded
module_sdio_driver().
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240403-module-owner-sdio-v2-3-ae46d6b955eb@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
This reverts commit 9ab4ad295622a3481818856762471c1f8c830e18.
I went out of coffee and applied it to the wrong tree. Blame on me.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
As of now, tg3_power_down_prepare always ends with success, but
the error handling code from former tg3_set_power_state call is still here.
This code became unreachable in commit c866b7eac073 ("tg3: Do not use
legacy PCI power management").
Remove (now unreachable) error handling code for simplification and change
tg3_power_down_prepare to a void function as its result is no more checked.
Signed-off-by: Nikita Kiryushin <kiryushin@ancud.ru>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240401191418.361747-1-kiryushin@ancud.ru
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
As of now, tg3_power_down_prepare always ends with success, but
the error handling code from former tg3_set_power_state call is still here.
This code became unreachable in commit c866b7eac073 ("tg3: Do not use
legacy PCI power management").
Remove (now unreachable) error handling code for simplification and change
tg3_power_down_prepare to a void function as its result is no more checked.
Signed-off-by: Nikita Kiryushin <kiryushin@ancud.ru>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240401191418.361747-1-kiryushin@ancud.ru
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
8922A needs to set UL MU/OFDMA power and fine tune power
error tolerance for proper response to AP's trigger frame.
Signed-off-by: Kuan-Chung Chen <damon.chen@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/20240401063818.12880-1-pkshih@realtek.com
|
|
When wpa_supplicant is initiated by users and not by NetworkManager,
the CQM configuration might not be set. Without this setting, ICs
with connection quality monitor handled by firmware won't detect
connection loss. To fix this we prepare a default setting upon
associated at first, then update again if any is given later.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/20240401033019.9664-1-pkshih@realtek.com
|
|
Currently, for each completion, we check the number of descriptor queue
and take it via mlxsw_pci_{sdq,rdq}_get(). This is inefficient, the
DQ should be the same for all the completions in CQ, as each CQ handles
only one DQ - SDQ or RDQ. This mapping is handled as part of DQ
initialization via mlxsw_cmd_mbox_sw2hw_dq_cq_set().
Instead, as part of DQ initialization, set DQ pointer in the appropriate
CQ structure. When we handle completions, warn in case that the DQ number
that we expect is different from the number we get in the CQE. Call
WARN_ON_ONCE() only after checking the value, to avoid calling this method
for each completion.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/a5b2559cd6d532c120f3194f89a1e257110318f1.1712062203.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, for each interrupt we call mlxsw_pci_cq_count() to determine the
number of CQs. This call makes additional two function's calls. This can
be removed by storing this value as part of structure 'mlxsw_pci', as we
already do for number of SDQs. Remove the function and
__mlxsw_pci_queue_count() which is now not used and store the value
instead.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/f08ad113e8160678f3c8d401382a696c6c7f44c7.1712062203.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The number of SDQs is stored as part of 'mlxsw_pci' structure. In some
cases, the driver uses this value and in some cases it calls
mlxsw_pci_sdq_count() to get the value. Align the code to use the
stored value. This simplifies the code and makes it clearer that the
value is always the same. Rename 'mlxsw_pci->num_sdq_cqs' to
'mlxsw_pci->num_sdqs' as now it is used not only in CQ context.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/0c8788506d9af35d589dbf64be35a508fd63d681.1712062203.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Completion queues are used for completions of RDQ or SDQ. Each
completion queue is used for one DQ. The first CQs are used for SDQs and
the rest are used for RDQs.
Currently, for each CQE (completion queue element), we check 'sr' value
(send/receive) to know if it is completion of RDQ or SDQ. Actually, we
do not really have to check it, as according to the queue number we know
if it handles completions of Rx or Tx.
Break the tasklet into two - one for Rx (RDQ) and one for Tx (SDQ). Then,
setup the appropriate tasklet for each queue as part of queue
initialization. Use 'sr' value for unlikely case that we get completion
with type that we do not expect. Call WARN_ON_ONCE() only after checking
the value, to avoid calling this method for each completion.
A next patch set will use NAPI to handle events, then we will have a
separate poll method for Rx and Tx. This change is a preparation for
NAPI usage.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/50fbc366f8de54cb5dc72a7c4f394333ef71f1d0.1712062203.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This function will be broken into several functions later. As preparation,
reorder variables to reverse xmas tree.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/7170a8f4429ecb5a539b0374c621697778ff8363.1712062203.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The previous patch changed the code to do not handle command interface
from event queue. With this change the wait queue is not used anymore.
Remove it and 'wait_done' variable.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/f3af6a5a9dabd97d2920cefe475c6aa57767f504.1712062203.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The device supports two event queues. EQ0 is used for command interface
completion events. EQ1 is used for completion events of RDQ or SDQ.
Currently, for each EQE (event queue element), we check the queue number
and handle accordingly. More than that, for each interrupt we schedule
tasklets for both EQs. This is really ineffective, especially because of
the fact that EQ0 is used only as part of driver init/fini, when EMADs are
not available. There is no point to schedule the tasklet for it and check
each EQE.
A previous patch changed the code to poll command interface for each use of
it. It means that now there is no real reason to use EQ0, as we poll the
command interface.
Initialize only one event queue and use it as EQ1 (this is determined by
queue number). Then, for each interrupt we can schedule the tasklet only
for one queue and we do not have to check the queue number. This
simplifies the code and should improve performance. Note that polling
command interface is ok as we use it only as part of driver init/fini.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/23d764f5c032e4c363b98590b746a4b32d2bf900.1712062203.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently we use MLXSW_PCI_EQS_COUNT event queues. A next patch will
change the driver to initialize only EQ1, as EQ0 is not required anymore
when we poll command interface.
Rename the macro to MLXSW_PCI_EQS_MAX as later we will not initialize
the maximum supported EQs, this value represents the maximum and a new
macro will be added to represent the actual used queues.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/b08df430b62f23ca1aa3aaa257896d2d95aa7691.1712062203.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Command interface is used for configuring and querying FW when EMADs are
not available. During the time that the driver sets up the asynchronous
queues, it polls the command interface for getting completions. Then,
there is a short period when asynchronous queues work, but EMADs are not
available (marked in the code as nopoll = true). During this time, we
send commands via command interface, but we do not poll it, as we can get
an interrupt for the completion. Completions of command interface are
received from HW in EQ0 (event queue 0).
The usage of EQ0 instead of polling is done only 4 times during
initialization and one time during tear down, but it makes an overhead
during lifetime of the driver. For each interrupt, we have to check if
we get events in EQ0 or EQ1 and handle them. This is really ineffective,
especially because of the fact that EQ0 is used only as part of driver
init/fini.
Instead, we can poll command interface for each call of cmd_exec(). It
means that when we send a command via command interface (as EMADs are
not available), we will poll it, regardless of availability of the
asynchronous queues. This will allow us to configure later only EQ1 and
simplify the flow.
Remove 'nopoll' indication and change mlxsw_pci_cmd_exec() to poll till
answer/timeout regardless of queues' state. For now, completions are
handled also by EQ0, but it will be removed in next patch. Additional
cleanups will be added in next patches.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/e674c70380ceda953e0e45a77334c5d22e69938f.1712062203.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This function will be used later only for EQ1. As preparation, reorder
variables to reverse xmas tree and return earlier when it is possible, to
simplify the code.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/2412d6c135b2a6aedb4484f5d8baab3aecd7b9ae.1712062203.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The structure 'mlxsw_pci_queue' stores several counters which were consumed
via debugfs. Since commit 9a32562becd9 ("mlxsw: Remove debugfs interface"),
these counters are not used. Remove them. This makes the 'union u' and
'struct eq' redundant. Maintain 'struct cq' as it will be extended later.
Replace increasing 'q->u.eq.ev_other_count' with WARN_ON_ONCE(), as it is
used in an unreasonable case of receiving event in EQ which is not EQ0 or
EQ1. When the queues are initialized, we check number of event queues and
fail with the print "Unsupported number of queues" in case that the driver
tries to initialize more than two queues.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/ee9e658800aa0390e08342100bc27daff4c176c0.1712062203.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, as part of mlxsw_pci_cq_tasklet(), we check if any item
was handled, and only in such case we arm doorbell. This is unlikely case,
as we schedule tasklet only for CQs that we get an event for them, which
means that they contain completions to handle. Remove this check, which
is supposed to be true always, and even if it is false, it is not a mistake
to ring the doorbell. We can warn on such case, but it is not really worth
to add a check which will be run for each CQ handling when we do not expect
to reach it and it does not point to logic error that should be handled.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/f8efa481bfe7bebb9f93bb803f44ab7da77f53e6.1712062203.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, the structure 'mlxsw_pci_queue_ops' holds a pointer to the
callback function of tasklet. This is used only for EQ and CQ. mlxsw
driver will use NAPI in a following patch set, so CQ will not use tasklet
anymore. As preparation, remove this pointer from the shared operation
structure and setup the tasklet as part of queue initialization.
For now, setup tasklet for EQ and CQ. Later, CQ code will be changed.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/a326cae5fc1ad085a1a063c004983de6fe389414.1712062203.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Move mlxsw_pci_cq_{init, fini}() after mlxsw_pci_cq_tasklet() as a next
patch will setup the tasklet as part of initialization.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/25196cb5baf5acf6ec1e956203790e018ba8e306.1712062203.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Move mlxsw_pci_eq_{init, fini}() after mlxsw_pci_eq_tasklet() as a next
patch will setup the tasklet as part of initialization.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/7ae120a02e1c490084daae7e684a0d40b7cce4e7.1712062203.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Firmware will return 0 on query BOOT/INIT PAGES for non-page supplier
functions (external host PF/VF/SF), so no page is needed to be
allocated for them.
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20240402133043.56322-12-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Page events are not issued by device on the function if
page_request_disable is set, so no need to create pages EQ.
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20240402133043.56322-11-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
