| Age | Commit message (Collapse) | Author |
|---|
|
In the current implementation, the enetc_xdp_xmit() always transmits
redirected XDP frames even if the link is down, but the frames cannot
be transmitted from TX BD rings when the link is down, so the frames
are still kept in the TX BD rings. If the XDP program is uninstalled,
users will see the following warning logs.
fsl_enetc 0000:00:00.0 eno0: timeout for tx ring #6 clear
More worse, the TX BD ring cannot work properly anymore, because the
HW PIR and CIR are not equal after the re-initialization of the TX
BD ring. At this point, the BDs between CIR and PIR are invalid,
which will cause a hardware malfunction.
Another reason is that there is internal context in the ring prefetch
logic that will retain the state from the first incarnation of the ring
and continue prefetching from the stale location when we re-initialize
the ring. The internal context is only reset by an FLR. That is to say,
for LS1028A ENETC, software cannot set the HW CIR and PIR when
initializing the TX BD ring.
It does not make sense to transmit redirected XDP frames when the link is
down. Add a link status check to prevent transmission in this condition.
This fixes part of the issue, but more complex cases remain. For example,
the TX BD ring may still contain unsent frames when the link goes down.
Those situations require additional patches, which will build on this
one.
Fixes: 9d2b68cc108d ("net: enetc: add support for XDP_REDIRECT")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Hariprasad Kelam <hkelam@marvell.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20251211020919.121113-1-wei.fang@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Commit [1] added the 40 bytes required by the PSP header+trailer and the
UDP header to MLX5E_ETH_HARD_MTU, which limits the device-wide max
software MTU that could be set. This is not okay, because most packets
are not PSP packets and it doesn't make sense to always reserve space
for headers which won't get added in most cases.
As it turns out, for TCP connections, PSP overhead is already taken into
account in the TCP MSS calculations via inet_csk(sk)->icsk_ext_hdr_len.
This was added in commit [2]. This means that the extra space reserved
in the hard MTU for mlx5 ends up unused and wasted.
Remove the unnecessary 40 byte reservation from hard MTU.
[1] commit e5a1861a298e ("net/mlx5e: Implement PSP Tx data path")
[2] commit e97269257fe4 ("net: psp: update the TCP MSS to reflect PSP
packet overhead")
Fixes: e5a1861a298e ("net/mlx5e: Implement PSP Tx data path")
Signed-off-by: Cosmin Ratiu <cratiu@nvidia.com>
Reviewed-by: Shahar Shitrit <shshitrit@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/1765284977-1363052-10-git-send-email-tariqt@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
During channel reconfiguration (e.g., ethtool private flags changes),
the driver can trigger a kernel BUG_ON in dql_completed() with the error
"kernel BUG at lib/dynamic_queue_limits.c:99".
The issue occurs in the following sequence:
During mlx5e_safe_switch_params(), old channels are deactivated via
mlx5e_deactivate_txqsq(). New channels are created and activated, taking
ownership of the netdev_queues and their BQL state.
When old channels are closed via mlx5e_close_txqsq(), there may be
pending TX descriptors (sq->cc != sq->pc) that were in-flight during the
deactivation.
mlx5e_free_txqsq_descs() frees these pending descriptors and attempts to
complete them via netdev_tx_completed_queue().
However, the BQL state (dql->num_queued and dql->num_completed) have
been reset in mlx5e_activate_txqsq and belong to the new queue owner,
leading to dql->num_queued - dql->num_completed < nbytes.
This triggers BUG_ON(count > num_queued - num_completed) in
dql_completed().
Fixes: 3b88a535a8e1 ("net/mlx5e: Defer channels closure to reduce interface down time")
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: William Tu <witu@nvidia.com>
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Link: https://patch.msgid.link/1765284977-1363052-9-git-send-email-tariqt@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When initializing the MAC addresses for an outbound IPsec packet offload
rule in mlx5e_ipsec_init_macs, the call to dst_neigh_lookup is used to
find the next-hop neighbor (typically the gateway in tunnel mode).
This call might create a new neighbor entry if one doesn't already
exist. This newly created entry starts in the INCOMPLETE state, as the
kernel hasn't yet sent an ARP or NDISC probe to resolve the MAC
address. In this case, neigh_ha_snapshot will correctly return an
all-zero MAC address.
IPsec packet offload requires the actual next-hop MAC address to
program the rule correctly. If the neighbor state is INCOMPLETE when
the rule is created, the hardware rule is programmed with an all-zero
destination MAC address. Packets sent using this rule will be
subsequently dropped by the receiving network infrastructure or host.
This patch adds a check specifically for the outbound offload path. If
neigh_ha_snapshot returns an all-zero MAC address, it proactively
calls neigh_event_send(n, NULL). This ensures the kernel immediately
sends the initial ARP or NDISC probe if one isn't already pending,
accelerating the resolution process. This helps prevent the hardware
rule from being programmed with an invalid MAC address and avoids
packet drops due to unresolved neighbors.
Fixes: 71670f766b8f ("net/mlx5e: Support routed networks during IPsec MACs initialization")
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/1765284977-1363052-8-git-send-email-tariqt@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Replace ipv6_stub->ipv6_dst_lookup_flow() with ip6_dst_lookup() in
mlx5e_ipsec_init_macs() since IPsec transformations are not needed
during Security Association setup - only basic routing information is
required for nexthop MAC address resolution.
This resolves an issue where XfrmOutNoStates error counter would be
incremented when xfrm policy is configured before xfrm state, as the
IPsec-aware routing function would attempt policy checks during SA
initialization.
Fixes: 71670f766b8f ("net/mlx5e: Support routed networks during IPsec MACs initialization")
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/1765284977-1363052-7-git-send-email-tariqt@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The firmware reset mechanism can be triggered by asynchronous events,
which may race with other devlink operations like devlink reload or
devlink dev eswitch set, potentially leading to inconsistent states.
This patch addresses the race by using the devl_lock to serialize the
firmware reset against other devlink operations. When a reset is
requested, the driver attempts to acquire the lock. If successful, it
sets a flag to block devlink reload or eswitch changes, ACKs the reset
to firmware and then releases the lock. If the lock is already held by
another operation, the driver NACKs the firmware reset request,
indicating that the reset cannot proceed.
Firmware reset does not keep the devl_lock and instead uses an internal
firmware reset bit. This is because firmware resets can be triggered by
asynchronous events, and processed in different threads. It is illegal
and unsafe to acquire a lock in one thread and attempt to release it in
another, as lock ownership is intrinsically thread-specific.
This change ensures that firmware resets and other devlink operations
are mutually exclusive during the critical reset request phase,
preventing race conditions.
Fixes: 38b9f903f22b ("net/mlx5: Handle sync reset request event")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Mateusz Berezecki <mberezecki@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/1765284977-1363052-6-git-send-email-tariqt@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The firmware tracer's format string validation and parameter counting
did not properly handle escaped percent signs (%%). This caused
fw_tracer to count more parameters when trace format strings contained
literal percent characters.
To fix it, allow %% to pass string validation and skip %% sequences when
counting parameters since they represent literal percent signs rather
than format specifiers.
Fixes: 70dd6fdb8987 ("net/mlx5: FW tracer, parse traces and kernel tracing support")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reported-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Closes: https://lore.kernel.org/netdev/hanz6rzrb2bqbplryjrakvkbmv4y5jlmtthnvi3thg5slqvelp@t3s3erottr6s/
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/1765284977-1363052-5-git-send-email-tariqt@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add validation for format string parameters in the firmware tracer to
prevent potential security vulnerabilities and crashes from malformed
format strings received from firmware.
The firmware tracer receives format strings from the device firmware and
uses them to format trace messages. Without proper validation, bad
firmware could provide format strings with invalid format specifiers
(e.g., %s, %p, %n) that could lead to crashes, or other undefined
behavior.
Add mlx5_tracer_validate_params() to validate that all format specifiers
in trace strings are limited to safe integer/hex formats (%x, %d, %i,
%u, %llx, %lx, etc.). Reject strings containing other format types that
could be used to access arbitrary memory or cause crashes.
Invalid format strings are added to the trace output for visibility with
"BAD_FORMAT: " prefix.
Fixes: 70dd6fdb8987 ("net/mlx5: FW tracer, parse traces and kernel tracing support")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Reported-by: Breno Leitao <leitao@debian.org>
Closes: https://lore.kernel.org/netdev/hanz6rzrb2bqbplryjrakvkbmv4y5jlmtthnvi3thg5slqvelp@t3s3erottr6s/
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/1765284977-1363052-4-git-send-email-tariqt@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Invoke drain_fw_reset() in the shutdown callback to ensure all
firmware reset handling is completed before shutdown proceeds.
Fixes: 16d42d313350 ("net/mlx5: Drain fw_reset when removing device")
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Shay Drori <shayd@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/1765284977-1363052-3-git-send-email-tariqt@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
drain_fw_reset() waits for ongoing firmware reset events and blocks new
event handling, but does not clear the reset requested flag, and may
keep sync reset polling.
To fix it, call mlx5_sync_reset_clear_reset_requested() to clear the
flag, stop sync reset polling, and resume health polling, ensuring
health issues are still detected after the firmware reset drain.
Fixes: 16d42d313350 ("net/mlx5: Drain fw_reset when removing device")
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Shay Drori <shayd@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/1765284977-1363052-2-git-send-email-tariqt@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Despite being documented as self-clearing, the RANEG bit sometimes
remains set, preventing auto-negotiation from happening.
Manually clear the RANEG bit after 10ms as advised by MaxLinear.
In order to not hold RTNL during the 10ms of waiting schedule
delayed work to take care of clearing the bit asynchronously, which
is similar to the self-clearing behavior.
Fixes: 22335939ec90 ("net: dsa: add driver for MaxLinear GSW1xx switch family")
Reported-by: Rasmus Villemoes <ravi@prevas.dk>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://patch.msgid.link/76745fceb5a3f53088110fb7a96acf88434088ca.1765241054.git.daniel@makrotopia.org
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The .shutdown operation should call dsa_switch_shutdown() just like
it is done also by the sibling lantiq_gswip driver. Not doing that
results in shutdown or reboot hanging and waiting for the CPU port
becoming free, which introduces a longer delay and a WARNING before
shutdown or reboot in case the driver is built-into the kernel.
Fix this by calling dsa_switch_shutdown() in the driver's shutdown
operation, harmonizing it with what is done in the lantiq_gswip
driver. As a side-effect this now allows to remove the previously
exported gswip_disable_switch() function which no longer got any
users.
Fixes: 22335939ec907 ("net: dsa: add driver for MaxLinear GSW1xx switch family")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://patch.msgid.link/77ed91a5206e5dbf5d3e83d7e364ebfda90d31fd.1765241054.git.daniel@makrotopia.org
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The driver's .remove operation was calling gswip_disable_switch() which
clears the GSWIP_MDIO_GLOB_ENABLE bit before calling
dsa_unregister_switch() and thereby violating a Golden Rule of driver
development to always unpublish userspace interfaces before disabling
hardware, as pointed out by Russell King.
Fix this by relying in GSWIP_MDIO_GLOB_ENABLE being cleared by the
.teardown operation introduced by the previous commit
("net: dsa: lantiq_gswip: fix teardown order").
Fixes: 22335939ec907 ("net: dsa: add driver for MaxLinear GSW1xx switch family")
Suggested-by: "Russell King (Oracle)" <linux@armlinux.org.uk>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://patch.msgid.link/63f882eeb910cf24503c35a443b541cc54a930f2.1765241054.git.daniel@makrotopia.org
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Russell King pointed out that disabling the switch by clearing
GSWIP_MDIO_GLOB_ENABLE before calling dsa_unregister_switch() is
problematic, as it violates a Golden Rule of driver development to
always first unpublish userspace interfaces and then disable the
hardware.
Fix this, and also simplify the probe() function, by introducing a
dsa_switch_ops teardown() operation which takes care of clearing the
GSWIP_MDIO_GLOB_ENABLE bit.
Fixes: 14fceff4771e5 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Suggested-by: "Russell King (Oracle)" <linux@armlinux.org.uk>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://patch.msgid.link/4ebd72a29edc1e4059b9666a26a0bb5d906a829a.1765241054.git.daniel@makrotopia.org
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Arnd Bergmann's patch [1] fixed the build dependency problem introduced by
bugfix commit cb2dc6d2869a ("can: Kconfig: select CAN driver infrastructure
by default"). This ended up as commit 6abd4577bccc ("can: fix build
dependency"), but I broke Arnd's fix by removing a dependency that we
thought was superfluous.
[1] https://lore.kernel.org/all/20251204100015.1033688-1-arnd@kernel.org/
Meanwhile the problem was also found by intel's kernel test robot,
complaining about undefined symbols:
| ERROR: modpost: "m_can_class_unregister" [drivers/net/can/m_can/m_can_platform.ko] undefined!
| ERROR: modpost: "m_can_class_free_dev" [drivers/net/can/m_can/m_can_platform.ko] undefined!
| ERROR: modpost: "m_can_class_allocate_dev" [drivers/net/can/m_can/m_can_platform.ko] undefined!
| ERROR: modpost: "m_can_class_get_clocks" [drivers/net/can/m_can/m_can_platform.ko] undefined!
| ERROR: modpost: "m_can_class_register" [drivers/net/can/m_can/m_can_platform.ko] undefined!
To fix this problem, add the missing dependency again.
Cc: Vincent Mailhol <mailhol@kernel.org>
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202512132253.vO9WFDJK-lkp@intel.com/
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202512180808.fTAUQ2XN-lkp@intel.com/
Reported-by: Arnd Bergmann <arnd@arndb.de>
Closes: https://lore.kernel.org/all/7427949a-ea7d-4854-9fe4-e01db7d878c7@app.fastmail.com/
Fixes: 6abd4577bccc ("can: fix build dependency")
Fixes: cb2dc6d2869a ("can: Kconfig: select CAN driver infrastructure by default")
Acked-by: Vincent Mailhol <mailhol@kernel.org>
Link: https://patch.msgid.link/20251217-can-fix-dependency-v1-1-fd2d4f2a2bf5@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
In e1000_tbi_should_accept() we read the last byte of the frame via
'data[length - 1]' to evaluate the TBI workaround. If the descriptor-
reported length is zero or larger than the actual RX buffer size, this
read goes out of bounds and can hit unrelated slab objects. The issue
is observed from the NAPI receive path (e1000_clean_rx_irq):
==================================================================
BUG: KASAN: slab-out-of-bounds in e1000_tbi_should_accept+0x610/0x790
Read of size 1 at addr ffff888014114e54 by task sshd/363
CPU: 0 PID: 363 Comm: sshd Not tainted 5.18.0-rc1 #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.0-59-gc9ba5276e321-prebuilt.qemu.org 04/01/2014
Call Trace:
<IRQ>
dump_stack_lvl+0x5a/0x74
print_address_description+0x7b/0x440
print_report+0x101/0x200
kasan_report+0xc1/0xf0
e1000_tbi_should_accept+0x610/0x790
e1000_clean_rx_irq+0xa8c/0x1110
e1000_clean+0xde2/0x3c10
__napi_poll+0x98/0x380
net_rx_action+0x491/0xa20
__do_softirq+0x2c9/0x61d
do_softirq+0xd1/0x120
</IRQ>
<TASK>
__local_bh_enable_ip+0xfe/0x130
ip_finish_output2+0x7d5/0xb00
__ip_queue_xmit+0xe24/0x1ab0
__tcp_transmit_skb+0x1bcb/0x3340
tcp_write_xmit+0x175d/0x6bd0
__tcp_push_pending_frames+0x7b/0x280
tcp_sendmsg_locked+0x2e4f/0x32d0
tcp_sendmsg+0x24/0x40
sock_write_iter+0x322/0x430
vfs_write+0x56c/0xa60
ksys_write+0xd1/0x190
do_syscall_64+0x43/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7f511b476b10
Code: 73 01 c3 48 8b 0d 88 d3 2b 00 f7 d8 64 89 01 48 83 c8 ff c3 66 0f 1f 44 00 00 83 3d f9 2b 2c 00 00 75 10 b8 01 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 31 c3 48 83 ec 08 e8 8e 9b 01 00 48 89 04 24
RSP: 002b:00007ffc9211d4e8 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
RAX: ffffffffffffffda RBX: 0000000000004024 RCX: 00007f511b476b10
RDX: 0000000000004024 RSI: 0000559a9385962c RDI: 0000000000000003
RBP: 0000559a9383a400 R08: fffffffffffffff0 R09: 0000000000004f00
R10: 0000000000000070 R11: 0000000000000246 R12: 0000000000000000
R13: 00007ffc9211d57f R14: 0000559a9347bde7 R15: 0000000000000003
</TASK>
Allocated by task 1:
__kasan_krealloc+0x131/0x1c0
krealloc+0x90/0xc0
add_sysfs_param+0xcb/0x8a0
kernel_add_sysfs_param+0x81/0xd4
param_sysfs_builtin+0x138/0x1a6
param_sysfs_init+0x57/0x5b
do_one_initcall+0x104/0x250
do_initcall_level+0x102/0x132
do_initcalls+0x46/0x74
kernel_init_freeable+0x28f/0x393
kernel_init+0x14/0x1a0
ret_from_fork+0x22/0x30
The buggy address belongs to the object at ffff888014114000
which belongs to the cache kmalloc-2k of size 2048
The buggy address is located 1620 bytes to the right of
2048-byte region [ffff888014114000, ffff888014114800]
The buggy address belongs to the physical page:
page:ffffea0000504400 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x14110
head:ffffea0000504400 order:3 compound_mapcount:0 compound_pincount:0
flags: 0x100000000010200(slab|head|node=0|zone=1)
raw: 0100000000010200 0000000000000000 dead000000000001 ffff888013442000
raw: 0000000000000000 0000000000080008 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
==================================================================
This happens because the TBI check unconditionally dereferences the last
byte without validating the reported length first:
u8 last_byte = *(data + length - 1);
Fix by rejecting the frame early if the length is zero, or if it exceeds
adapter->rx_buffer_len. This preserves the TBI workaround semantics for
valid frames and prevents touching memory beyond the RX buffer.
Fixes: 2037110c96d5 ("e1000: move tbi workaround code into helper function")
Cc: stable@vger.kernel.org
Signed-off-by: Guangshuo Li <lgs201920130244@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
During the IDPF init phase, the mailbox runs in poll mode until it is
configured to properly handle interrupts. The previous delay of 300ms is
excessively long for the mailbox polling mechanism, which causes a slow
initialization of ~2s:
echo 0000:06:12.4 > /sys/bus/pci/drivers/idpf/bind
[ 52.444239] idpf 0000:06:12.4: enabling device (0000 -> 0002)
[ 52.485005] idpf 0000:06:12.4: Device HW Reset initiated
[ 54.177181] idpf 0000:06:12.4: PTP init failed, err=-EOPNOTSUPP
[ 54.206177] idpf 0000:06:12.4: Minimum RX descriptor support not provided, using the default
[ 54.206182] idpf 0000:06:12.4: Minimum TX descriptor support not provided, using the default
Changing the delay to 300us avoids the delays during the initial mailbox
transactions, making the init phase much faster:
[ 83.342590] idpf 0000:06:12.4: enabling device (0000 -> 0002)
[ 83.384402] idpf 0000:06:12.4: Device HW Reset initiated
[ 83.518323] idpf 0000:06:12.4: PTP init failed, err=-EOPNOTSUPP
[ 83.547430] idpf 0000:06:12.4: Minimum RX descriptor support not provided, using the default
[ 83.547435] idpf 0000:06:12.4: Minimum TX descriptor support not provided, using the default
Fixes: 4930fbf419a7 ("idpf: add core init and interrupt request")
Signed-off-by: Brian Vazquez <brianvv@google.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Samuel Salin <Samuel.salin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
IPU SDK versions 1.9 through 2.0.5 require send buffer to contain a single
empty memory region. Set number of regions to 1 and use appropriate send
buffer size to satisfy this requirement.
Fixes: 6aa53e861c1a ("idpf: implement get LAN MMIO memory regions")
Suggested-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
There are off-by-one bugs when configuring RSS hash key and lookup
table, causing out-of-bounds reads to memory [1] and out-of-bounds
writes to device registers.
Before commit 43a3d9ba34c9 ("i40evf: Allow PF driver to configure RSS"),
the loop upper bounds were:
i <= I40E_VFQF_{HKEY,HLUT}_MAX_INDEX
which is safe since the value is the last valid index.
That commit changed the bounds to:
i <= adapter->rss_{key,lut}_size / 4
where `rss_{key,lut}_size / 4` is the number of dwords, so the last
valid index is `(rss_{key,lut}_size / 4) - 1`. Therefore, using `<=`
accesses one element past the end.
Fix the issues by using `<` instead of `<=`, ensuring we do not exceed
the bounds.
[1] KASAN splat about rss_key_size off-by-one
BUG: KASAN: slab-out-of-bounds in iavf_config_rss+0x619/0x800
Read of size 4 at addr ffff888102c50134 by task kworker/u8:6/63
CPU: 0 UID: 0 PID: 63 Comm: kworker/u8:6 Not tainted 6.18.0-rc2-enjuk-tnguy-00378-g3005f5b77652-dirty #156 PREEMPT(voluntary)
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2 04/01/2014
Workqueue: iavf iavf_watchdog_task
Call Trace:
<TASK>
dump_stack_lvl+0x6f/0xb0
print_report+0x170/0x4f3
kasan_report+0xe1/0x1a0
iavf_config_rss+0x619/0x800
iavf_watchdog_task+0x2be7/0x3230
process_one_work+0x7fd/0x1420
worker_thread+0x4d1/0xd40
kthread+0x344/0x660
ret_from_fork+0x249/0x320
ret_from_fork_asm+0x1a/0x30
</TASK>
Allocated by task 63:
kasan_save_stack+0x30/0x50
kasan_save_track+0x14/0x30
__kasan_kmalloc+0x7f/0x90
__kmalloc_noprof+0x246/0x6f0
iavf_watchdog_task+0x28fc/0x3230
process_one_work+0x7fd/0x1420
worker_thread+0x4d1/0xd40
kthread+0x344/0x660
ret_from_fork+0x249/0x320
ret_from_fork_asm+0x1a/0x30
The buggy address belongs to the object at ffff888102c50100
which belongs to the cache kmalloc-64 of size 64
The buggy address is located 0 bytes to the right of
allocated 52-byte region [ffff888102c50100, ffff888102c50134)
The buggy address belongs to the physical page:
page: refcount:0 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x102c50
flags: 0x200000000000000(node=0|zone=2)
page_type: f5(slab)
raw: 0200000000000000 ffff8881000418c0 dead000000000122 0000000000000000
raw: 0000000000000000 0000000080200020 00000000f5000000 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff888102c50000: 00 00 00 00 00 00 00 fc fc fc fc fc fc fc fc fc
ffff888102c50080: 00 00 00 00 00 00 00 fc fc fc fc fc fc fc fc fc
>ffff888102c50100: 00 00 00 00 00 00 04 fc fc fc fc fc fc fc fc fc
^
ffff888102c50180: 00 00 00 00 00 00 00 00 fc fc fc fc fc fc fc fc
ffff888102c50200: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
Fixes: 43a3d9ba34c9 ("i40evf: Allow PF driver to configure RSS")
Signed-off-by: Kohei Enju <enjuk@amazon.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The maximum number of descriptors supported by the hardware is
hardware-dependent and can be retrieved using
i40e_get_max_num_descriptors(). Move this function to a shared header
and use it when checking for valid ring_len parameter rather than using
hardcoded value.
By fixing an over-acceptance issue, behavior change could be seen where
ring_len could now be rejected while configuring rx and tx queues if its
size is larger than the hardware-dependent maximum number of
descriptors.
Fixes: 55d225670def ("i40e: add validation for ring_len param")
Signed-off-by: Gregory Herrero <gregory.herrero@oracle.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Add service task schedule to set_rx_mode.
In some cases there are error messages printed out in PTP application
(ptp4l):
ptp4l[13848.762]: port 1 (ens2f3np3): received SYNC without timestamp
ptp4l[13848.825]: port 1 (ens2f3np3): received SYNC without timestamp
ptp4l[13848.887]: port 1 (ens2f3np3): received SYNC without timestamp
This happens when service task would not run immediately after
set_rx_mode, and we need it for setup tasks. This service task checks, if
PTP RX packets are hung in firmware, and propagate correct settings such
as multicast address for IEEE 1588 Precision Time Protocol.
RX timestamping depends on some of these filters set. Bug happens only
with high PTP packets frequency incoming, and not every run since
sometimes service task is being ran from a different place immediately
after starting ptp4l.
Fixes: 0e4425ed641f ("i40e: fix: do not sleep in netdev_ops")
Reviewed-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Przemyslaw Korba <przemyslaw.korba@intel.com>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Since commit dfb073d32cac ("ptp: Return -EINVAL on ptp_clock_register if
required ops are NULL"), PTP clock registered through ptp_clock_register
is required to have ptp_clock_info.settime64 set, however, neither MVM
nor MLD's PTP clock implementation sets it, resulting in warnings when
the interface starts up, like
WARNING: drivers/ptp/ptp_clock.c:325 at ptp_clock_register+0x2c8/0x6b8, CPU#1: wpa_supplicant/469
CPU: 1 UID: 0 PID: 469 Comm: wpa_supplicant Not tainted 6.18.0+ #101 PREEMPT(full)
ra: ffff800002732cd4 iwl_mvm_ptp_init+0x114/0x188 [iwlmvm]
ERA: 9000000002fdc468 ptp_clock_register+0x2c8/0x6b8
iwlwifi 0000:01:00.0: Failed to register PHC clock (-22)
I don't find an appropriate firmware interface to implement settime64()
for iwlwifi MLD/MVM, thus instead create a stub that returns
-EOPTNOTSUPP only, suppressing the warning and allowing the PTP clock to
be registered.
Reported-by: Nathan Chancellor <nathan@kernel.org>
Closes: https://lore.kernel.org/all/20251108044822.GA3262936@ax162/
Signed-off-by: Yao Zi <ziyao@disroot.org>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
tested-by: damian Tometzki damian@riscv-rocks.de
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20251204123204.9316-1-ziyao@disroot.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
On my system the arithmetic done on the firmware numbers
results in a negative number, but since the types are
unsigned it gets interpreted as a large positive number.
The end result is that the firmware gets rejected and wifi
is defunct.
Switch to signed types to handle this case correctly.
iwlwifi 0000:0c:00.0: Driver unable to support your firmware API. Driver supports FW core 4294967294..2, firmware is 2.
iwlwifi 0000:0c:00.0: Direct firmware load for iwlwifi-5000-4.ucode failed with error -2
iwlwifi 0000:0c:00.0: Direct firmware load for iwlwifi-5000-3.ucode failed with error -2
iwlwifi 0000:0c:00.0: Direct firmware load for iwlwifi-5000-2.ucode failed with error -2
iwlwifi 0000:0c:00.0: Direct firmware load for iwlwifi-5000-1.ucode failed with error -2
iwlwifi 0000:0c:00.0: no suitable firmware found!
iwlwifi 0000:0c:00.0: minimum version required: iwlwifi-5000-1
iwlwifi 0000:0c:00.0: maximum version supported: iwlwifi-5000-5
iwlwifi 0000:0c:00.0: check git://git.kernel.org/pub/scm/linux/kernel/git/firmware/linux-firmware.git
Cc: stable@vger.kernel.org
Fixes: 5f708cccde9d ("wifi: iwlwifi: add a new FW file numbering scheme")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=220805
Link: https://patch.msgid.link/20251113222852.15896-1-ville.syrjala@linux.intel.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This avoids occasional skb_under_panic Oops from wl1271_tx_work. In this case, headroom is
less than needed (typically 110 - 94 = 16 bytes).
Signed-off-by: Peter Astrand <astrand@lysator.liu.se>
Link: https://patch.msgid.link/097bd417-e1d7-acd4-be05-47b199075013@lysator.liu.se
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
As originally proposed in [1], the ath12k driver was re-architected in
the ath12k-ng branch to separate the logic specific to 802.11be (Wi-Fi
7) from the core logic. This separation will allow ath12k to also
support 802.11bn (Wi-Fi 8) in the future. Now merge this into ath-next.
Many thanks to everyone who worked on this re-architecture. Special
thanks to Vasanthakumar Thiagarajan and Baochen Qiang who reviewed
every patch, and to Ripan Deuri for the ath12k-ng => ath-next merge
conflict resolution.
Link: https://lore.kernel.org/all/4a17d730-ede8-463e-98d8-9b0291d0ca45@oss.qualcomm.com/ # [1]
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
This reverts commit 9c194fe4625db18f93d5abcfb7f7997557a0b29d.
This commit breaks all USB wifi adapters supported by rtw88:
usb 1-2: new high-speed USB device number 6 using xhci_hcd
usb 1-2: New USB device found, idVendor=2357, idProduct=0138, bcdDevice= 2.10
usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-2: Product: 802.11ac NIC
usb 1-2: Manufacturer: Realtek
usb 1-2: SerialNumber: 123456
------------[ cut here ]------------
WARNING: CPU: 3 PID: 152 at kernel/workqueue.c:5667 alloc_workqueue_noprof+0x676/0x770
[...]
Call Trace:
<TASK>
? rtw_usb_probe+0x30e/0xa5c [rtw88_usb 4af3cb64eedafeecbfb08f80c1e9e2893e2ee7a6]
rtw_usb_probe+0x3eb/0xa5c [rtw88_usb 4af3cb64eedafeecbfb08f80c1e9e2893e2ee7a6]
usb_probe_interface+0xdd/0x2c0
really_probe+0xdb/0x340
? pm_runtime_barrier+0x55/0x90
? __pfx___device_attach_driver+0x10/0x10
__driver_probe_device+0x78/0x140
driver_probe_device+0x1f/0xa0
__device_attach_driver+0x89/0x110
bus_for_each_drv+0x8f/0xe0
__device_attach+0xb0/0x1c0
bus_probe_device+0x90/0xa0
device_add+0x663/0x880
usb_set_configuration+0x5a5/0x870
usb_generic_driver_probe+0x4a/0x70
usb_probe_device+0x3d/0x140
? driver_sysfs_add+0x59/0xd0
really_probe+0xdb/0x340
? pm_runtime_barrier+0x55/0x90
? __pfx___device_attach_driver+0x10/0x10
__driver_probe_device+0x78/0x140
driver_probe_device+0x1f/0xa0
__device_attach_driver+0x89/0x110
bus_for_each_drv+0x8f/0xe0
__device_attach+0xb0/0x1c0
bus_probe_device+0x90/0xa0
device_add+0x663/0x880
usb_new_device.cold+0x141/0x3b5
hub_event+0x1132/0x1900
? page_counter_uncharge+0x4a/0x90
process_one_work+0x190/0x350
worker_thread+0x2d7/0x410
? __pfx_worker_thread+0x10/0x10
kthread+0xf9/0x240
? __pfx_kthread+0x10/0x10
? __pfx_kthread+0x10/0x10
ret_from_fork+0x1c1/0x1f0
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1a/0x30
</TASK>
---[ end trace 0000000000000000 ]---
rtw88_8822bu 1-2:1.0: failed to create RX work queue
rtw88_8822bu 1-2:1.0: failed to init USB RX
rtw88_8822bu 1-2:1.0: Firmware version 27.2.0, H2C version 13
rtw88_8822bu 1-2:1.0: probe with driver rtw88_8822bu failed with error -12
WQ_UNBOUND is not compatible with WQ_BH. Comment in enum wq_flags in
workqueue.h says:
/* BH wq only allows the following flags */
__WQ_BH_ALLOWS = WQ_BH | WQ_HIGHPRI | WQ_PERCPU,
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/d57efe48-b8ff-4bf1-942c-7e808535eda6@gmail.com
|
|
TID getting from ieee80211_get_tid() might be out of range of array size
of sta_entry->tids[], so check TID is less than MAX_TID_COUNT. Othwerwise,
UBSAN warn:
UBSAN: array-index-out-of-bounds in drivers/net/wireless/realtek/rtlwifi/rtl8192cu/trx.c:514:30
index 10 is out of range for type 'rtl_tid_data [9]'
Fixes: 8ca4cdef9329 ("wifi: rtlwifi: rtl8192cu: Fix TX aggregation")
Signed-off-by: Morning Star <alexbestoso@gmail.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/1764232628-13625-1-git-send-email-pkshih@realtek.com
|
|
The indirect IO is necessary for RTL8822CS, but not necessary for other
chips. Otherwiese, it throws errors and becomes unusable.
rtw88_8723cs mmc1:0001:1: WOW Firmware version 11.0.0, H2C version 0
rtw88_8723cs mmc1:0001:1: Firmware version 11.0.0, H2C version 0
rtw88_8723cs mmc1:0001:1: sdio read32 failed (0xf0): -110
rtw88_8723cs mmc1:0001:1: sdio write8 failed (0x1c): -110
rtw88_8723cs mmc1:0001:1: sdio read32 failed (0xf0): -110
By vendor driver, only RTL8822CS and RTL8822ES need indirect IO, but
RTL8822ES isn't supported yet. Therefore, limit it to RTL8822CS only.
Reported-by: Andrey Skvortsov <andrej.skvortzov@gmail.com>
Closes: https://lore.kernel.org/linux-wireless/07a32e2d6c764eb1bd9415b5a921a652@realtek.com/T/#m997b4522f7209ba629561c776bfd1d13ab24c1d4
Fixes: 58de1f91e033 ("wifi: rtw88: sdio: use indirect IO for device registers before power-on")
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Tested-by: Andrey Skvortsov <andrej.skvortzov@gmail.com>
Link: https://patch.msgid.link/1764034729-1251-1-git-send-email-pkshih@realtek.com
|
|
Some Potron SFP+ XGSPON ONU sticks are shipped with different EEPROM
vendor ID and vendor name strings, but are otherwise functionally
identical to the existing "Potron SFP+ XGSPON ONU Stick" handled by
sfp_quirk_potron().
These modules, including units distributed under the "Better Internet"
branding, use the same UART pin assignment and require the same
TX_FAULT/LOS behaviour and boot delay. Re-use the existing Potron
quirk for this EEPROM variant.
Signed-off-by: Marcus Hughes <marcus.hughes@betterinternet.ltd>
Link: https://patch.msgid.link/20251207210355.333451-1-marcus.hughes@betterinternet.ltd
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2025-12-10
Arnd Bergmann's patch fixes a build dependency with the CAN protocols
and drivers introduced in the current development cycle.
The last patch is by me and fixes the error handling cleanup in the
gs_usb driver.
* tag 'linux-can-fixes-for-6.19-20251210' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
can: gs_usb: gs_can_open(): fix error handling
can: fix build dependency
====================
Link: https://patch.msgid.link/20251210083448.2116869-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
On execution path with raised B44_FLAG_EXTERNAL_PHY, b44_readphy()
leaves bmcr value uninitialized and it is used later in the code.
Add check of this flag at the beginning of the b44_nway_reset() and
exit early of the function with restarting autonegotiation if an
external PHY is used.
Fixes: 753f492093da ("[B44]: port to native ssb support")
Reviewed-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexey Simakov <bigalex934@gmail.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20251205155815.4348-1-bigalex934@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The new icssg-prueth driver needs the same dependency as the other parts
that use the ptp-1588:
WARNING: unmet direct dependencies detected for TI_ICSS_IEP
Depends on [m]: NETDEVICES [=y] && ETHERNET [=y] && NET_VENDOR_TI [=y] && PTP_1588_CLOCK_OPTIONAL [=m] && TI_PRUSS [=y]
Selected by [y]:
- TI_PRUETH [=y] && NETDEVICES [=y] && ETHERNET [=y] && NET_VENDOR_TI [=y] && PRU_REMOTEPROC [=y] && NET_SWITCHDEV [=y]
Add the correct dependency on the two drivers missing it, and remove
the pointless 'imply' in the process.
Fixes: e654b85a693e ("net: ti: icssg-prueth: Add ICSSG Ethernet driver for AM65x SR1.0 platforms")
Fixes: 511f6c1ae093 ("net: ti: icssm-prueth: Adds ICSSM Ethernet driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20251204100138.1034175-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit 2603be9e8167 ("can: gs_usb: gs_can_open(): improve error handling")
added missing error handling to the gs_can_open() function.
The driver uses 2 USB anchors to track the allocated URBs: the TX URBs in
struct gs_can::tx_submitted for each netdev and the RX URBs in struct
gs_usb::rx_submitted for the USB device. gs_can_open() allocates the RX
URBs, while TX URBs are allocated during gs_can_start_xmit().
The cleanup in gs_can_open() kills all anchored dev->tx_submitted
URBs (which is not necessary since the netdev is not yet registered), but
misses the parent->rx_submitted URBs.
Fix the problem by killing the rx_submitted instead of the tx_submitted.
Fixes: 2603be9e8167 ("can: gs_usb: gs_can_open(): improve error handling")
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20251210-gs_usb-fix-error-handling-v1-1-d6a5a03f10bb@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
A recent bugfix introduced a new problem with Kconfig dependencies:
WARNING: unmet direct dependencies detected for CAN_DEV
Depends on [n]: NETDEVICES [=n] && CAN [=m]
Selected by [m]:
- CAN [=m] && NET [=y]
Since the CAN core code now links into the CAN device code, that
particular function needs to be available, though the rest of it
does not.
Revert the incomplete fix and instead use Makefile logic to avoid
the link failure.
Fixes: cb2dc6d2869a ("can: Kconfig: select CAN driver infrastructure by default")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202512091523.zty3CLmc-lkp@intel.com/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://patch.msgid.link/20251204100015.1033688-1-arnd@kernel.org
[mkl: removed module option from CAN_DEV help text (thanks Vincent)]
[mkl: removed '&& CAN' from Kconfig dependency (thanks Vincent)]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Consider a multi-link AP configuration:
MLD vif (MAC addr: aa:bb)
|-- 2.4 GHz link (BSSID: aa:bb)
|-- 5 GHz link (BSSID: cc:dd)
For AP vdevs, ath12k creates a DP peer using the arvif's BSSID and stores
it in dp_hw->dp_peers_list. During scan operations, the driver assigns an
arvif to the scan vdev and uses the vif's MAC address as its BSSID. In
the above scenario, the scan vdev MAC address (aa:bb) matches the BSSID
of the 2.4 GHz AP link, causing a duplicate entry in dp_hw->dp_peers_list
and leading to scan vdev creation failure.
Failure in vif bringup sequence:
1. Create AP vdev for 2.4 GHz link:
- Assign arvif with BSSID = aa:bb and link_id = 0.
- Create DP peer with address aa:bb and add to dp_hw->dp_peers_list.
2. Create scan vdev for 5 GHz link:
- Assign arvif with BSSID = aa:bb (same as vif MAC address) and
link_id = 15.
- Attempt to create another DP peer with address aa:bb.
- Operation fails because aa:bb already exists in dp_hw->dp_peers_list,
resulting in duplicate entry conflict.
3. Delete scan vdev for 5 GHz link.
4. Create AP vdev for 5 GHz link.
Since DP peer is not needed for scan operations, identify scan vdev using
arvif->link_id >= IEEE80211_MLD_MAX_NUM_LINKS and skip DP peer creation
and deletion.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.5-01651-QCAHKSWPL_SILICONZ-1
Signed-off-by: Ripan Deuri <quic_rdeuri@quicinc.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20251207072717.95542-1-quic_rdeuri@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux
Pull i3c updates from Alexandre Belloni:
"HDR support has finally been added. mipi-i3c-hci has been reworked and
Intel Nova Lake-S support has been added.
Subsystem:
- Add HDR transfer support
Drivers:
- dw: fix bus hang on Agilex5
- mipi-i3c-hci: Intel Nova Lake-S support, IOMMU support
- svc: HDR support"
* tag 'i3c/for-6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux: (28 commits)
regmap: i3c: switch to use i3c_xfer from i3c_priv_xfer
net: mctp i3c: switch to use i3c_xfer from i3c_priv_xfer
hwmon: (lm75): switch to use i3c_xfer from i3c_priv_xfer
i3c: document i3c_xfers
i3c: fix I3C_SDR bit number
i3c: master: svc: Add basic HDR mode support
i3c: master: svc: Replace bool rnw with union for HDR support
i3c: Switch to use new i3c_xfer from i3c_priv_xfer
i3c: Add HDR API support
i3c: master: add WQ_PERCPU to alloc_workqueue users
i3c: master: Remove i3c_device_free_ibi from i3c_device_remove
i3c: mipi-i3c-hci-pci: Set d3cold_delay to 0 for Intel controllers
i3c: mipi-i3c-hci-pci: Add LTR support for Intel controllers
i3c: mipi-i3c-hci-pci: Add exit callback
i3c: mipi-i3c-hci-pci: Change callback parameter
i3c: mipi-i3c-hci-pci: Allocate a structure for mipi_i3c_hci_pci device information
i3c: mipi-i3c-hci-pci: Factor out intel_reset()
i3c: mipi-i3c-hci-pci: Factor out private registers ioremapping
i3c: mipi-i3c-hci-pci: Constify driver data
i3c: mipi-i3c-hci-pci: Use readl_poll_timeout()
...
|
|
Pull rdma updates from Jason Gunthorpe:
"This has another new RDMA driver 'bng_en' for latest generation
Broadcom NICs. There might be one more new driver still to come.
Otherwise it is a fairly quite cycle. Summary:
- Minor driver bug fixes and updates to cxgb4, rxe, rdmavt, bnxt_re,
mlx5
- Many bug fix patches for irdma
- WQ_PERCPU annotations and system_dfl_wq changes
- Improved mlx5 support for "other eswitches" and multiple PFs
- 1600Gbps link speed reporting support. Four Digits Now!
- New driver bng_en for latest generation Broadcom NICs
- Bonding support for hns
- Adjust mlx5's hmm based ODP to work with the very large address
space created by the new 5 level paging default on x86
- Lockdep fixups in rxe and siw"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (65 commits)
RDMA/rxe: reclassify sockets in order to avoid false positives from lockdep
RDMA/siw: reclassify sockets in order to avoid false positives from lockdep
RDMA/bng_re: Remove prefetch instruction
RDMA/core: Reduce cond_resched() frequency in __ib_umem_release
RDMA/irdma: Fix SRQ shadow area address initialization
RDMA/irdma: Remove doorbell elision logic
RDMA/irdma: Do not set IBK_LOCAL_DMA_LKEY for GEN3+
RDMA/irdma: Do not directly rely on IB_PD_UNSAFE_GLOBAL_RKEY
RDMA/irdma: Add missing mutex destroy
RDMA/irdma: Fix SIGBUS in AEQ destroy
RDMA/irdma: Add a missing kfree of struct irdma_pci_f for GEN2
RDMA/irdma: Fix data race in irdma_free_pble
RDMA/irdma: Fix data race in irdma_sc_ccq_arm
RDMA/mlx5: Add support for 1600_8x lane speed
RDMA/core: Add new IB rate for XDR (8x) support
IB/mlx5: Reduce IMR KSM size when 5-level paging is enabled
RDMA/bnxt_re: Pass correct flag for dma mr creation
RDMA/bnxt_re: Fix the inline size for GenP7 devices
RDMA/hns: Support reset recovery for bond
RDMA/hns: Support link state reporting for bond
...
|
|
For XDP_TX action in bnxt_rx_xdp(), clearing of the event flags is not
correct. __bnxt_poll_work() -> bnxt_rx_pkt() -> bnxt_rx_xdp() may be
looping within NAPI and some event flags may be set in earlier
iterations. In particular, if BNXT_TX_EVENT is set earlier indicating
some XDP_TX packets are ready and pending, it will be cleared if it is
XDP_TX action again. Normally, we will set BNXT_TX_EVENT again when we
successfully call __bnxt_xmit_xdp(). But if the TX ring has no more
room, the flag will not be set. This will cause the TX producer to be
ahead but the driver will not hit the TX doorbell.
For multi-buf XDP_TX, there is no need to clear the event flags and set
BNXT_AGG_EVENT. The BNXT_AGG_EVENT flag should have been set earlier in
bnxt_rx_pkt().
The visible symptom of this is that the RX ring associated with the
TX XDP ring will eventually become empty and all packets will be dropped.
Because this condition will cause the driver to not refill the RX ring
seeing that the TX ring has forever pending XDP_TX packets.
The fix is to only clear BNXT_RX_EVENT when we have successfully
called __bnxt_xmit_xdp().
Fixes: 7f0a168b0441 ("bnxt_en: Add completion ring pointer in TX and RX ring structures")
Reported-by: Pavel Dubovitsky <pdubovitsky@meta.com>
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20251203003024.2246699-1-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
commit 46e7860ef941 ("gve: Move ptp_schedule_worker to gve_init_clock")
moved the first invocation of the AQ command REPORT_NIC_TIMESTAMP to
gve_probe(). However, gve_init_clock() invoking REPORT_NIC_TIMESTAMP is
not valid until after gve_probe() invokes the AQ command
CONFIGURE_DEVICE_RESOURCES.
Failure to do so results in the following error:
gve 0000:00:07.0: failed to read NIC clock -11
This was missed earlier because the driver under test was loaded at
runtime instead of boot-time. The boot-time driver had already
initialized the device, causing the runtime driver to successfully call
gve_init_clock() incorrectly.
Fixes: 46e7860ef941 ("gve: Move ptp_schedule_worker to gve_init_clock")
Reviewed-by: Ankit Garg <nktgrg@google.com>
Signed-off-by: Tim Hostetler <thostet@google.com>
Signed-off-by: Harshitha Ramamurthy <hramamurthy@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251202200207.1434749-1-hramamurthy@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Wake-on-Lan does currently not work for r8169 in DASH mode, e.g. the
ASUS Pro WS X570-ACE with RTL8168fp/RTL8117.
Fix by not returning early in rtl_prepare_power_down when dash_enabled.
While this fixes WoL, it still kills the OOB RTL8117 remote management
BMC connection. Fix by not calling rtl8168_driver_stop if WoL is enabled.
Fixes: 065c27c184d6 ("r8169: phy power ops")
Signed-off-by: René Rebe <rene@exactco.de>
Cc: stable@vger.kernel.org
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/20251202.194137.1647877804487085954.rene@exactco.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cited commit added a dedicated mutex (instead of RTNL) to protect the
multicast route list, so that it will not change while the driver
periodically traverses it in order to update the kernel about multicast
route stats that were queried from the device.
One instance of list entry deletion (during route replace) was missed
and it can result in a use-after-free [1].
Fix by acquiring the mutex before deleting the entry from the list and
releasing it afterwards.
[1]
BUG: KASAN: slab-use-after-free in mlxsw_sp_mr_stats_update+0x4a5/0x540 drivers/net/ethernet/mellanox/mlxsw/spectrum_mr.c:1006 [mlxsw_spectrum]
Read of size 8 at addr ffff8881523c2fa8 by task kworker/2:5/22043
CPU: 2 UID: 0 PID: 22043 Comm: kworker/2:5 Not tainted 6.18.0-rc1-custom-g1a3d6d7cd014 #1 PREEMPT(full)
Hardware name: Mellanox Technologies Ltd. MSN2010/SA002610, BIOS 5.6.5 08/24/2017
Workqueue: mlxsw_core mlxsw_sp_mr_stats_update [mlxsw_spectrum]
Call Trace:
<TASK>
dump_stack_lvl+0xba/0x110
print_report+0x174/0x4f5
kasan_report+0xdf/0x110
mlxsw_sp_mr_stats_update+0x4a5/0x540 drivers/net/ethernet/mellanox/mlxsw/spectrum_mr.c:1006 [mlxsw_spectrum]
process_one_work+0x9cc/0x18e0
worker_thread+0x5df/0xe40
kthread+0x3b8/0x730
ret_from_fork+0x3e9/0x560
ret_from_fork_asm+0x1a/0x30
</TASK>
Allocated by task 29933:
kasan_save_stack+0x30/0x50
kasan_save_track+0x14/0x30
__kasan_kmalloc+0x8f/0xa0
mlxsw_sp_mr_route_add+0xd8/0x4770 [mlxsw_spectrum]
mlxsw_sp_router_fibmr_event_work+0x371/0xad0 drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c:7965 [mlxsw_spectrum]
process_one_work+0x9cc/0x18e0
worker_thread+0x5df/0xe40
kthread+0x3b8/0x730
ret_from_fork+0x3e9/0x560
ret_from_fork_asm+0x1a/0x30
Freed by task 29933:
kasan_save_stack+0x30/0x50
kasan_save_track+0x14/0x30
__kasan_save_free_info+0x3b/0x70
__kasan_slab_free+0x43/0x70
kfree+0x14e/0x700
mlxsw_sp_mr_route_add+0x2dea/0x4770 drivers/net/ethernet/mellanox/mlxsw/spectrum_mr.c:444 [mlxsw_spectrum]
mlxsw_sp_router_fibmr_event_work+0x371/0xad0 drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c:7965 [mlxsw_spectrum]
process_one_work+0x9cc/0x18e0
worker_thread+0x5df/0xe40
kthread+0x3b8/0x730
ret_from_fork+0x3e9/0x560
ret_from_fork_asm+0x1a/0x30
Fixes: f38656d06725 ("mlxsw: spectrum_mr: Protect multicast route list with a lock")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/f996feecfd59fde297964bfc85040b6d83ec6089.1764695650.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We sometimes observe use-after-free when dereferencing a neighbour [1].
The problem seems to be that the driver stores a pointer to the
neighbour, but without holding a reference on it. A reference is only
taken when the neighbour is used by a nexthop.
Fix by simplifying the reference counting scheme. Always take a
reference when storing a neighbour pointer in a neighbour entry. Avoid
taking a referencing when the neighbour is used by a nexthop as the
neighbour entry associated with the nexthop already holds a reference.
Tested by running the test that uncovered the problem over 300 times.
Without this patch the problem was reproduced after a handful of
iterations.
[1]
BUG: KASAN: slab-use-after-free in mlxsw_sp_neigh_entry_update+0x2d4/0x310
Read of size 8 at addr ffff88817f8e3420 by task ip/3929
CPU: 3 UID: 0 PID: 3929 Comm: ip Not tainted 6.18.0-rc4-virtme-g36b21a067510 #3 PREEMPT(full)
Hardware name: Nvidia SN5600/VMOD0013, BIOS 5.13 05/31/2023
Call Trace:
<TASK>
dump_stack_lvl+0x6f/0xa0
print_address_description.constprop.0+0x6e/0x300
print_report+0xfc/0x1fb
kasan_report+0xe4/0x110
mlxsw_sp_neigh_entry_update+0x2d4/0x310
mlxsw_sp_router_rif_gone_sync+0x35f/0x510
mlxsw_sp_rif_destroy+0x1ea/0x730
mlxsw_sp_inetaddr_port_vlan_event+0xa1/0x1b0
__mlxsw_sp_inetaddr_lag_event+0xcc/0x130
__mlxsw_sp_inetaddr_event+0xf5/0x3c0
mlxsw_sp_router_netdevice_event+0x1015/0x1580
notifier_call_chain+0xcc/0x150
call_netdevice_notifiers_info+0x7e/0x100
__netdev_upper_dev_unlink+0x10b/0x210
netdev_upper_dev_unlink+0x79/0xa0
vrf_del_slave+0x18/0x50
do_set_master+0x146/0x7d0
do_setlink.isra.0+0x9a0/0x2880
rtnl_newlink+0x637/0xb20
rtnetlink_rcv_msg+0x6fe/0xb90
netlink_rcv_skb+0x123/0x380
netlink_unicast+0x4a3/0x770
netlink_sendmsg+0x75b/0xc90
__sock_sendmsg+0xbe/0x160
____sys_sendmsg+0x5b2/0x7d0
___sys_sendmsg+0xfd/0x180
__sys_sendmsg+0x124/0x1c0
do_syscall_64+0xbb/0xfd0
entry_SYSCALL_64_after_hwframe+0x4b/0x53
[...]
Allocated by task 109:
kasan_save_stack+0x30/0x50
kasan_save_track+0x14/0x30
__kasan_kmalloc+0x7b/0x90
__kmalloc_noprof+0x2c1/0x790
neigh_alloc+0x6af/0x8f0
___neigh_create+0x63/0xe90
mlxsw_sp_nexthop_neigh_init+0x430/0x7e0
mlxsw_sp_nexthop_type_init+0x212/0x960
mlxsw_sp_nexthop6_group_info_init.constprop.0+0x81f/0x1280
mlxsw_sp_nexthop6_group_get+0x392/0x6a0
mlxsw_sp_fib6_entry_create+0x46a/0xfd0
mlxsw_sp_router_fib6_replace+0x1ed/0x5f0
mlxsw_sp_router_fib6_event_work+0x10a/0x2a0
process_one_work+0xd57/0x1390
worker_thread+0x4d6/0xd40
kthread+0x355/0x5b0
ret_from_fork+0x1d4/0x270
ret_from_fork_asm+0x11/0x20
Freed by task 154:
kasan_save_stack+0x30/0x50
kasan_save_track+0x14/0x30
__kasan_save_free_info+0x3b/0x60
__kasan_slab_free+0x43/0x70
kmem_cache_free_bulk.part.0+0x1eb/0x5e0
kvfree_rcu_bulk+0x1f2/0x260
kfree_rcu_work+0x130/0x1b0
process_one_work+0xd57/0x1390
worker_thread+0x4d6/0xd40
kthread+0x355/0x5b0
ret_from_fork+0x1d4/0x270
ret_from_fork_asm+0x11/0x20
Last potentially related work creation:
kasan_save_stack+0x30/0x50
kasan_record_aux_stack+0x8c/0xa0
kvfree_call_rcu+0x93/0x5b0
mlxsw_sp_router_neigh_event_work+0x67d/0x860
process_one_work+0xd57/0x1390
worker_thread+0x4d6/0xd40
kthread+0x355/0x5b0
ret_from_fork+0x1d4/0x270
ret_from_fork_asm+0x11/0x20
Fixes: 6cf3c971dc84 ("mlxsw: spectrum_router: Add private neigh table")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/92d75e21d95d163a41b5cea67a15cd33f547cba6.1764695650.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
mlxsw_sp_router_schedule_work() takes a reference on a neighbour,
expecting a work item to release it later on. However, we might fail to
schedule the work item, in which case the neighbour reference count will
be leaked.
Fix by taking the reference just before scheduling the work item. Note
that mlxsw_sp_router_schedule_work() can receive a NULL neighbour
pointer, but neigh_clone() handles that correctly.
Spotted during code review, did not actually observe the reference count
leak.
Fixes: 151b89f6025a ("mlxsw: spectrum_router: Reuse work neighbor initialization in work scheduler")
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/ec2934ae4aca187a8d8c9329a08ce93cca411378.1764695650.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The local variable 'val' was never clamped to -75000 or 180000 because
the return value of clamp_val() was not used. Fix this by assigning the
clamped value back to 'val', and use clamp() instead of clamp_val().
Cc: stable@vger.kernel.org
Fixes: a557a92e6881 ("net: phy: marvell-88q2xxx: add support for temperature sensor")
Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev>
Reviewed-by: Dimitri Fedrau <dima.fedrau@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20251202172743.453055-3-thorsten.blum@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Enable host bridge emulation for PCI_DOMAINS_GENERIC platforms (Dan
Williams)
- Switch vmd from custom domain number allocator to the common
allocator to prevent a potential race with new non-VMD buses (Dan
Williams)
- Enable Precision Time Measurement (PTM) only if device advertises
support for a relevant role, to prevent invalid PTM Requests that
cause ACS violations that are reported as AER Uncorrectable
Non-Fatal errors (Mika Westerberg)
Resource management:
- Prevent resource tree corruption when BAR resize fails (Ilpo
Järvinen)
- Restore BARs to the original size if a BAR resize fails (Ilpo
Järvinen)
- Remove BAR release from BAR resize attempts by the xe, i915, and
amdgpu drivers so the PCI core can restore BARs if the resize fails
(Ilpo Järvinen)
- Move Resizable BAR code to rebar.c (Ilpo Järvinen)
- Add pci_rebar_size_supported() and use it in i915 and xe (Ilpo
Järvinen)
- Add pci_rebar_get_max_size() and use it in xe and amdgpu (Ilpo
Järvinen)
Power management and error handling:
- For drivers using PCI legacy suspend, save config state at suspend
so that state (not any earlier state from enumeration, probe, or
error recovery) will be restored when resuming (Lukas Wunner)
- For devices with no driver or a driver that lacks power management,
save config state at hibernate so that state (not any earlier state
from enumeration, probe, or error recovery) will be restored when
resuming (Lukas Wunner)
- Save device config space on device addition, before driver binding,
so error recovery works more reliably (Lukas Wunner)
- Drop pci_save_state() from several drivers that no longer need it
since the PCI core always does it and pci_restore_state() no longer
invalidates the saved state (Lukas Wunner)
- Document use of pci_save_state() by drivers to capture the state
they want restored during error recovery (Lukas Wunner)
Power control:
- Add a struct pci_ops.assert_perst() function pointer to
assert/deassert PCIe PERST# and implement it for the qcom driver
(Krishna Chaitanya Chundru)
- Add DT binding and pwrctrl driver for the Toshiba TC9563 PCIe
switch, which must be held in reset after poweron so the pwrctrl
driver can configure the switch via I2C before bringing up the
links (Krishna Chaitanya Chundru)
Endpoint framework:
- Convert the endpoint doorbell test to use a threaded IRQ to fix a
'sleeping while atomic' issue (Bhanu Seshu Kumar Valluri)
- Add endpoint VNTB MSI doorbell support to reduce latency between
host and endpoint (Frank Li)
New native PCIe controller drivers:
- Add CIX Sky1 host controller DT binding and driver (Hans Zhang)
- Add NXP S32G host controller DT binding and driver (Vincent
Guittot)
- Add Renesas RZ/G3S host controller DT binding and driver (Claudiu
Beznea)
- Add SpacemiT K1 host controller DT binding and driver (Alex Elder)
Amlogic Meson PCIe controller driver:
- Update DT binding to name DBI region 'dbi', not 'elbi', and update
driver to support both (Manivannan Sadhasivam)
Apple PCIe controller driver:
- Move struct pci_host_bridge allocation from pci_host_common_init()
to callers, which significantly simplifies pcie-apple (Marc
Zyngier)
Broadcom STB PCIe controller driver:
- Disable advertising ASPM L0s support correctly (Jim Quinlan)
- Add a panic/die handler to print diagnostic info in case PCIe
caused an unrecoverable abort (Jim Quinlan)
Cadence PCIe controller driver:
- Add module support for Cadence platform host and endpoint
controller driver (Manikandan K Pillai)
- Split headers into 'legacy' (LGA) and 'high perf' (HPA) to prepare
for new CIX Sky1 driver (Manikandan K Pillai)
MediaTek PCIe controller driver:
- Convert DT binding to YAML schema (Christian Marangi)
- Add Airoha AN7583 DT compatible and driver support (Christian
Marangi)
Qualcomm PCIe controller driver:
- Add Qualcomm Kaanapali to SM8550 DT binding (Qiang Yu)
- Add required 'power-domains' and 'resets' to qcom sa8775p, sc7280,
sc8280xp, sm8150, sm8250, sm8350, sm8450, sm8550, x1e80100 DT
schemas (Krzysztof Kozlowski)
- Look up OPP using both frequency and data rate (not just frequency)
so RPMh votes can account for both (Krishna Chaitanya Chundru)
Rockchip DesignWare PCIe controller driver:
- Add Rockchip RK3528 compatible strings in DT binding (Yao Zi)
STMicroelectronics STM32MP25 PCIe controller driver:
- Fix a race between link training and endpoint register
initialization (Christian Bruel)
- Align endpoint allocations to match the ATU requirements (Christian
Bruel)
Synopsys DesignWare PCIe controller driver:
- Clear L1 PM Substate Capability 'Supported' bits unless glue driver
says it's supported, which prevents users from enabling non-working
L1SS. Currently only qcom and tegra194 support L1SS (Bjorn Helgaas)
- Remove now-superfluous L1SS disable code from tegra194 (Bjorn
Helgaas)
- Configure L1SS support in dw-rockchip when DT says
'supports-clkreq' (Shawn Lin)
TI Keystone PCIe controller driver:
- Fail the probe instead of silently succeeding if ks_pcie_of_data
didn't specify Root Complex or Endpoint mode (Siddharth Vadapalli)
- Make keystone buildable as a loadable module, except on ARM32 where
hook_fault_code() is __init (Siddharth Vadapalli)"
* tag 'pci-v6.19-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (100 commits)
MAINTAINERS: Add Manivannan Sadhasivam as PCI/pwrctrl maintainer
MAINTAINERS: Add CIX Sky1 PCIe controller driver maintainer
PCI: sky1: Add PCIe host support for CIX Sky1
dt-bindings: PCI: Add CIX Sky1 PCIe Root Complex bindings
PCI: cadence: Add support for High Perf Architecture (HPA) controller
MAINTAINERS: Add NXP S32G PCIe controller driver maintainer
PCI: s32g: Add NXP S32G PCIe controller driver (RC)
PCI: dwc: Add register and bitfield definitions
dt-bindings: PCI: s32g: Add NXP S32G PCIe controller
PCI: Add Renesas RZ/G3S host controller driver
PCI: host-generic: Move bridge allocation outside of pci_host_common_init()
dt-bindings: PCI: Add Renesas RZ/G3S PCIe controller binding
PCI: Validate pci_rebar_size_supported() input
Documentation: PCI: Amend error recovery doc with pci_save_state() rules
treewide: Drop pci_save_state() after pci_restore_state()
PCI/ERR: Ensure error recoverability at all times
PCI/PM: Stop needlessly clearing state_saved on enumeration and thaw
PCI/PM: Reinstate clearing state_saved in legacy and !PM codepaths
PCI: dw-rockchip: Configure L1SS support
PCI: tegra194: Remove unnecessary L1SS disable code
...
|
|
Clear hca_devcom_comp in device's private data after unregistering it in
LAG teardown. Otherwise a slightly lagging second pass through
mlx5_unload_one() might try to unregister it again and trip over
use-after-free.
On s390 almost all PCI level recovery events trigger two passes through
mxl5_unload_one() - one through the poll_health() method and one through
mlx5_pci_err_detected() as callback from generic PCI error recovery.
While testing PCI error recovery paths with more kernel debug features
enabled, this issue reproducibly led to kernel panics with the following
call chain:
Unable to handle kernel pointer dereference in virtual kernel address space
Failing address: 6b6b6b6b6b6b6000 TEID: 6b6b6b6b6b6b6803 ESOP-2 FSI
Fault in home space mode while using kernel ASCE.
AS:00000000705c4007 R3:0000000000000024
Oops: 0038 ilc:3 [#1]SMP
CPU: 14 UID: 0 PID: 156 Comm: kmcheck Kdump: loaded Not tainted
6.18.0-20251130.rc7.git0.16131a59cab1.300.fc43.s390x+debug #1 PREEMPT
Krnl PSW : 0404e00180000000 0000020fc86aa1dc (__lock_acquire+0x5c/0x15f0)
R:0 T:1 IO:0 EX:0 Key:0 M:1 W:0 P:0 AS:3 CC:2 PM:0 RI:0 EA:3
Krnl GPRS: 0000000000000000 0000020f00000001 6b6b6b6b6b6b6c33 0000000000000000
0000000000000000 0000000000000000 0000000000000001 0000000000000000
0000000000000000 0000020fca28b820 0000000000000000 0000010a1ced8100
0000010a1ced8100 0000020fc9775068 0000018fce14f8b8 0000018fce14f7f8
Krnl Code: 0000020fc86aa1cc: e3b003400004 lg %r11,832
0000020fc86aa1d2: a7840211 brc 8,0000020fc86aa5f4
*0000020fc86aa1d6: c09000df0b25 larl %r9,0000020fca28b820
>0000020fc86aa1dc: d50790002000 clc 0(8,%r9),0(%r2)
0000020fc86aa1e2: a7840209 brc 8,0000020fc86aa5f4
0000020fc86aa1e6: c0e001100401 larl %r14,0000020fca8aa9e8
0000020fc86aa1ec: c01000e25a00 larl %r1,0000020fca2f55ec
0000020fc86aa1f2: a7eb00e8 aghi %r14,232
Call Trace:
__lock_acquire+0x5c/0x15f0
lock_acquire.part.0+0xf8/0x270
lock_acquire+0xb0/0x1b0
down_write+0x5a/0x250
mlx5_detach_device+0x42/0x110 [mlx5_core]
mlx5_unload_one_devl_locked+0x50/0xc0 [mlx5_core]
mlx5_unload_one+0x42/0x60 [mlx5_core]
mlx5_pci_err_detected+0x94/0x150 [mlx5_core]
zpci_event_attempt_error_recovery+0xcc/0x388
Fixes: 5a977b5833b7 ("net/mlx5: Lag, move devcom registration to LAG layer")
Signed-off-by: Gerd Bayer <gbayer@linux.ibm.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Acked-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20251202-fix_lag-v1-1-59e8177ffce0@linux.ibm.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Packets with pkt_type == PACKET_LOOPBACK are captured by
handle_frame() function, but they don't have L2 header.
We should not process them in handle_mode_l2().
This doesn't affect old L2 functionality, since handling
was anyway incorrect.
Handle them the same way as in br_handle_frame():
just pass the skb.
To observe invalid behaviour, just start "ping -b" on bcast address
of port-interface.
Fixes: 2ad7bf363841 ("ipvlan: Initial check-in of the IPVLAN driver.")
Signed-off-by: Dmitry Skorodumov <skorodumov.dmitry@huawei.com>
Link: https://patch.msgid.link/20251202103906.4087675-1-skorodumov.dmitry@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
According to MaxLinear engineer Benny Weng the RX lane of the SerDes
port of the GSW1xx switches is inverted in hardware, and the
SGMII_PHY_RX0_CFG2_INVERT bit is set by default in order to compensate
for that. Hence also set the SGMII_PHY_RX0_CFG2_INVERT bit by default in
gsw1xx_pcs_reset().
Fixes: 22335939ec90 ("net: dsa: add driver for MaxLinear GSW1xx switch family")
Reported-by: Rasmus Villemoes <ravi@prevas.dk>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/ca10e9f780c0152ecf9ae8cbac5bf975802e8f99.1764668951.git.daniel@makrotopia.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When support for RTL8211F(D)(I)-VD-CG was introduced in commit
bb726b753f75 ("net: phy: realtek: add support for RTL8211F(D)(I)-VD-CG")
the implementation assumed that this PHY model doesn't have the
control register PHYCR2 (Page 0xa43 Address 0x19). This
assumption was based on the differences in CLKOUT configurations
between RTL8211FVD and the remaining RTL8211F PHYs. In the latter
commit 2c67301584f2
("net: phy: realtek: Avoid PHYCR2 access if PHYCR2 not present")
this assumption was expanded to the PHY-mode EEE.
I performed tests on RTL8211FI-VD-CG and confirmed that disabling
PHY-mode EEE works correctly and is uniform with other PHYs
supported by the driver. To validate the correctness,
I contacted Realtek support. Realtek confirmed that PHY-mode EEE on
RTL8211F(D)(I)-VD-CG is configured via Page 0xa43 Address 0x19 bit 5.
Moreover, Realtek informed me that the most recent datasheet
for RTL8211F(D)(I)-VD-CG v1.1 is incomplete and the naming of
control registers is partly inconsistent. The errata I
received from Realtek corrects the naming as follows:
| Register | Datasheet v1.1 | Errata |
|-------------------------|----------------|--------|
| Page 0xa44 Address 0x11 | PHYCR2 | PHYCR3 |
| Page 0xa43 Address 0x19 | N/A | PHYCR2 |
This information confirms that the supposedly missing control register,
PHYCR2, exists in the RTL8211F(D)(I)-VD-CG under the same address and
the same name. It controls widely the same configs as other PHYs from
the RTL8211F series (e.g. PHY-mode EEE). Clock out configuration is an
exception.
Given all this information, restore disabling of the PHY-mode EEE.
Fixes: 2c67301584f2 ("net: phy: realtek: Avoid PHYCR2 access if PHYCR2 not present")
Signed-off-by: Ivan Galkin <ivan.galkin@axis.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20251202-phy_eee-v1-1-fe0bf6ab3df0@axis.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
PSP is unregistered twice in:
_mlx5e_remove -> mlx5e_psp_unregister
mlx5e_nic_cleanup -> mlx5e_psp_unregister
This leads to a refcount underflow in some conditions:
------------[ cut here ]------------
refcount_t: underflow; use-after-free.
WARNING: CPU: 2 PID: 1694 at lib/refcount.c:28 refcount_warn_saturate+0xd8/0xe0
[...]
mlx5e_psp_unregister+0x26/0x50 [mlx5_core]
mlx5e_nic_cleanup+0x26/0x90 [mlx5_core]
mlx5e_remove+0xe6/0x1f0 [mlx5_core]
auxiliary_bus_remove+0x18/0x30
device_release_driver_internal+0x194/0x1f0
bus_remove_device+0xc6/0x130
device_del+0x159/0x3c0
mlx5_rescan_drivers_locked+0xbc/0x2a0 [mlx5_core]
[...]
Do not directly remove psp from the _mlx5e_remove path, the PSP cleanup
happens as part of profile cleanup.
Fixes: 89ee2d92f66c ("net/mlx5e: Support PSP offload functionality")
Signed-off-by: Cosmin Ratiu <cratiu@nvidia.com>
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/1764602008-1334866-3-git-send-email-tariqt@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
