| Age | Commit message (Collapse) | Author |
|---|
|
Testing in two circumstances:
1. back to back optical SFP+ connection between two LS1028A-QDS ports
with the SCH-26908 riser card
2. T1042 with on-board AQR115 PHY using "OCSGMII", as per
https://lore.kernel.org/lkml/aIuEvaSCIQdJWcZx@FUE-ALEWI-WINX/
strongly suggests that enabling in-band auto-negotiation is actually
possible when the lane baud rate is 3.125 Gbps.
It was previously thought that this would not be the case, because it
was only tested on 2500base-x links with on-board Aquantia PHYs, where
it was noticed that MII_LPA is always reported as zero, and it was
thought that this is because of the PCS.
Test case #1 above shows it is not, and the configured MII_ADVERTISE on
system A ends up in the MII_LPA on system B, when in 2500base-x mode
(IF_MODE=0).
Test case #2, which uses "SGMII" auto-negotiation (IF_MODE=3) for the
3.125 Gbps lane, is actually a misconfiguration, but it is what led to
the discovery.
There is actually an old bug in the Lynx PCS driver - it expects all
register values to contain their default out-of-reset values, as if the
PCS were initialized by the Reset Configuration Word (RCW) settings.
There are 2 cases in which this is problematic:
- if the bootloader (or previous kexec-enabled Linux) wrote a different
IF_MODE value
- if dynamically changing the SerDes protocol from 1000base-x to
2500base-x, e.g. by replacing the optical SFP module.
Specifically in test case #2, an accidental alignment between the
bootloader configuring the PCS to expect SGMII in-band code words, and
the AQR115 PHY actually transmitting SGMII in-band code words when
operating in the "OCSGMII" system interface protocol, led to the PCS
transmitting replicated symbols at 3.125 Gbps baud rate. This could only
have happened if the PCS saw and reacted to the SGMII code words in the
first place.
Since test #2 is invalid from a protocol perspective (there seems to be
no standard way of negotiating the data rate of 2500 Mbps with SGMII,
and the lower data rates should remain 10/100/1000), in-band auto-negotiation
for 2500base-x effectively means Clause 37 (i.e. IF_MODE=0).
Make 2500base-x be treated like 1000base-x in this regard, by removing
all prior limitations and calling lynx_pcs_config_giga().
This adds a new feature: LINK_INBAND_ENABLE and at the same time fixes
the Lynx PCS's long standing problem that the registers (specifically
IF_MODE, but others could be misconfigured as well) are not written by
the driver to the known valid values for 2500base-x.
Co-developed-by: Alexander Wilhelm <alexander.wilhelm@westermo.com>
Signed-off-by: Alexander Wilhelm <alexander.wilhelm@westermo.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20251125103507.749654-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The ageing time is in 5s step, ranging from 1 step to 0xffff steps, so
add appropriate attributes.
Signed-off-by: David Yang <mmyangfl@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20251129042137.3034032-1-mmyangfl@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This patch fixes multiple spelling mistakes in dl2k driver comments:
- "deivices" -> "devices"
- "Ttransmit" -> "Transmit"
- "catastronphic" -> "catastrophic"
- "Extened" -> "Extended"
Also fix incorrect unit description: `rx_timeout` uses 640ns increments,
not 64ns.
- "64ns" -> "640ns"
These are comment-only changes and do not affect runtime behavior.
Signed-off-by: Yeounsu Moon <yyyynoom@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20251130220652.5425-2-yyyynoom@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Convert the enetc driver to use the new .get_rx_ring_count
ethtool operation instead of implementing .get_rxnfc for handling
ETHTOOL_GRXRINGS command. This simplifies the code in two ways:
1. For enetc_get_rxnfc(): Remove the ETHTOOL_GRXRINGS case from the
switch statement while keeping other cases for classifier rules.
2. For enetc4_get_rxnfc(): Remove it completely and use
enetc_get_rxnfc() instead.
Now on, enetc_get_rx_ring_count() is the callback that returns the
number of RX rings for enetc driver.
Also, remove the documentation around enetc4_get_rxnfc(), which was not
matching what the function did(?!).
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251128-gxring_freescale-v1-3-22a978abf29e@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Convert the dpaa2 driver to use the new .get_rx_ring_count
ethtool operation instead of implementing .get_rxnfc for handling
ETHTOOL_GRXRINGS command. This simplifies the code by removing the
ETHTOOL_GRXRINGS case from the switch statement and replacing it with
a direct return of the queue count.
The driver still maintains .get_rxnfc for other commands including
ETHTOOL_GRXCLSRLCNT, ETHTOOL_GRXCLSRULE, and ETHTOOL_GRXCLSRLALL.
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251128-gxring_freescale-v1-2-22a978abf29e@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Convert the gianfar driver to use the new .get_rx_ring_count
ethtool operation instead of implementing .get_rxnfc for handling
ETHTOOL_GRXRINGS command. This simplifies the code by removing the
ETHTOOL_GRXRINGS case from the switch statement and replacing it with
a direct return of the queue count.
The driver still maintains .get_rxnfc for other commands including
ETHTOOL_GRXCLSRLCNT, ETHTOOL_GRXCLSRULE, and ETHTOOL_GRXCLSRLALL.
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251128-gxring_freescale-v1-1-22a978abf29e@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Previously .maxattr was shared for both WG_CMD_GET_DEVICE and
WG_CMD_SET_DEVICE. Now that it is split, then we can lower it
for WG_CMD_GET_DEVICE to follow the documentation which defines
.maxattr as WGDEVICE_A_IFNAME for WG_CMD_GET_DEVICE.
$ grep -hC5 'one but not both of:' include/uapi/linux/wireguard.h
* WG_CMD_GET_DEVICE
* -----------------
*
* May only be called via NLM_F_REQUEST | NLM_F_DUMP. The command
* should contain one but not both of:
*
* WGDEVICE_A_IFINDEX: NLA_U32
* WGDEVICE_A_IFNAME: NLA_NUL_STRING, maxlen IFNAMSIZ - 1
*
* The kernel will then return several messages [...]
While other attributes weren't rejected previously, the consensus
is that nobody sends those attributes, so nothing should break.
Link: https://lore.kernel.org/r/aRyLoy2iqbkUipZW@zx2c4.com/
Suggested-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
This patch converts WireGuard from using the legacy struct genl_ops
to struct genl_split_ops, by applying the same transformation as
genl_cmd_full_to_split() would otherwise do at runtime.
WGDEVICE_A_MAX is swapped for WGDEVICE_A_PEERS, while they are
currently equivalent, then .maxattr should be the maximum attribute
that a given command supports, and not change along with WGDEVICE_A_MAX.
This is an incremental step towards adopting netlink policy code
generated by ynl-gen, ensuring that the code and spec is aligned.
This is a trivial patch with no behavioural changes intended.
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
When converting the netlink policies to YNL, the constants used
in the policy have to be visible to userspace.
As NOISE_*_KEY_LEN isn't visible to userspace, change the policy
to use WG_KEY_LEN, as also documented in the UAPI header:
$ grep WG_KEY_LEN include/uapi/linux/wireguard.h
* WGDEVICE_A_PRIVATE_KEY: NLA_EXACT_LEN, len WG_KEY_LEN
* WGDEVICE_A_PUBLIC_KEY: NLA_EXACT_LEN, len WG_KEY_LEN
* WGPEER_A_PUBLIC_KEY: NLA_EXACT_LEN, len WG_KEY_LEN
* WGPEER_A_PRESHARED_KEY: NLA_EXACT_LEN, len WG_KEY_LEN
[...]
Add a couple of BUILD_BUG_ON() to ensure that they stay in sync.
No behavioural changes intended.
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
Use NLA_POLICY_NESTED_ARRAY() to perform nested array validation
in the policy validation step.
The nested policy was already enforced through nla_parse_nested(),
however extack wasn't passed previously, so no fancy error messages.
With the nested attributes being validated directly in the policy, the
policy argument can be set to NULL in the calls to nla_parse_nested().
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
WireGuard is a modern enough genetlink family, that it doesn't need
resv_start_op. It already had policies in place when it was first
merged, it has also never used the reserved field, or other things
toggled by resv_start_op.
wireguard-tools have always used zero initialized memory, and have never
touched the reserved field, neither have any other clients I have
checked. Closed-source clients are much more likely to use the
embeddedable library from wireguard-tools, than a DIY implementation
using uninitialized memory.
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
Commit 84eaf4359c36 ("net: ethtool: add get_rx_ring_count callback to
optimize RX ring queries") added specific support for GRXRINGS callback,
simplifying .get_rxnfc.
Remove the handling of GRXRINGS in .get_rxnfc() by moving it to the new
.get_rx_ring_count().
This simplifies the RX ring count retrieval and aligns bcmgenet with the
new ethtool API for querying RX ring parameters.
Signed-off-by: Breno Leitao <leitao@debian.org>
Link: https://patch.msgid.link/20251127-grxrings_broadcom-v1-2-b0b182864950@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit 84eaf4359c36 ("net: ethtool: add get_rx_ring_count callback to
optimize RX ring queries") added specific support for GRXRINGS callback,
simplifying .get_rxnfc.
Remove the handling of GRXRINGS in .get_rxnfc() by moving it to the new
.get_rx_ring_count().
This simplifies the RX ring count retrieval and aligns bnxt with the new
ethtool API for querying RX ring parameters.
Signed-off-by: Breno Leitao <leitao@debian.org>
Link: https://patch.msgid.link/20251127-grxrings_broadcom-v1-1-b0b182864950@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, if NVMEM provider is probed later than Aquantia, loading the
firmware will fail with -EINVAL.
To fix this, simply check for -EPROBE_DEFER when NVMEM is attempted and
return it.
Fixes: e93984ebc1c8 ("net: phy: aquantia: add firmware load support")
Signed-off-by: Robert Marko <robimarko@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/20251127114514.460924-1-robimarko@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Johannes Berg says:
====================
Apart from the usual small things just driver updates:
- mt76:
- WED support for >32-bit DMA
- airoha NPU support
- regdomain improvements
- continued WiFi7/MLO work
- rtw89
- support USB devices RTL8852AU and RTL8852CU
- initial work for RTL8922DE
- improved injection support
- rtl8xxxu: 40 MHz connection fixes/support
- brcmfmac: Acer A1 840 tablet quirk
* tag 'wireless-next-2025-11-27' of https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (152 commits)
wifi: mac80211: allow sharing identical chanctx for S1G interfaces
wifi: nl80211: vendor-cmd: intel: fix a blank kernel-doc line warning
wifi: cfg80211: include s1g_primary_2mhz when comparing chandefs
wifi: cfg80211: include s1g_primary_2mhz when sending chandef
wifi: ieee80211: correct FILS status codes
mt76: mt7615: Fix memory leak in mt7615_mcu_wtbl_sta_add()
wifi: mt76: mt792x: fix wifi init fail by setting MCU_RUNNING after CLC load
wifi: mt76: Strip whitespace from build ddate
wifi: mt76: mt7996: Add missing locking in mt7996_mac_sta_rc_work()
wifi: mt76: mt7996: skip ieee80211_iter_keys() on scanning link remove
wifi: mt76: mt7996: skip deflink accounting for offchannel links
wifi: mt76: Move mt76_abort_scan out of mt76_reset_device()
wifi: mt76: mt7996: move mt7996_update_beacons under mt76 mutex
wifi: mt76: mt7996: grab mt76 mutex in mt7996_mac_sta_event()
wifi: mt76: mt7925: ensure the 6GHz A-MPDU density cap from the hardware.
wifi: mt76: mt7996: fix EMI rings for RRO
wifi: mt76: mt7996: fix using wrong phy to start in mt7996_mac_restart()
wifi: mt76: mt7996: fix MLO set key and group key issues
wifi: mt76: mt7996: fix MLD group index assignment
wifi: mt76: mt7996: use correct link_id when filling TXD and TXP
...
====================
Link: https://patch.msgid.link/20251127103806.17776-3-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The firmware can now cache the virtual link admin state (auto/on/off) of
all VFs and as such, the PF driver no longer has to intercept the VF
driver's port_phy_qcfg() call and then provide the link admin state.
If the FW does not have this capability, fall back to the existing
interception method.
The initial default link admin state (auto) is also set initially when
the VFs are created.
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Mohammad Shuab Siddique <mohammad-shuab.siddique@broadcom.com>
Signed-off-by: Rob Miller <rmiller@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20251126215648.1885936-7-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
With End-of-Packet padding (EOP) set, the chip will disable Relaxed
Ordering (RO) of TPA data packets. A TPA segment with EOP set will be
padded to the next cache boundary and can potentially overwrite the
beginning bytes of the next TPA segment when RO is enabled on 5760X.
To prevent that, the chip disables RO for TPA when EOP is set.
To take advantge of RO and higher performance, do not set EOP on
5760X chips when TPA is enabled. Define a proper RX_BD_FLAGS_AGG_EOP
constant to make it clear that we are setting EOP.
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20251126215648.1885936-6-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
On newer chips that use NQs and CQs, add the CQ ring dump to
bnxt_dump_cp_sw_state() to make it more complete.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20251126215648.1885936-5-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
MSIX is always requested when the RoCE driver calls bnxt_register_dev().
We already check bnxt_ulp_registered(), so checking the flag is
redundant. It was a left-over flag after converting to auxbus, so
remove it.
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20251126215648.1885936-4-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Rturn early with -EOPNOTSUPP and an extack message if the PHY type is
BaseT since module status is not available for BaseT.
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Gautam R A <gautam-r.a@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20251126215648.1885936-3-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The priority packet and byte counters in ethtool -S are returned by
the driver based on the pri2cos mapping. The assumption is that each
priority is mapped to one and only one hardware CoS queue. In a
special RoCE configuration, the FW uses combined CoS queue 0 and CoS
queue 1 for the priority mapped to CoS queue 0. In this special
case, we need to add the CoS queue 0 and CoS queue 1 counters for
the priority packet and byte counters.
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20251126215648.1885936-2-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The current dev_warn messages for too many VLAN changes are confusing
and one place incorrectly references "add" instead of "delete" VLANs
due to copy-paste errors.
- Use dev_info instead of dev_warn to lower the log level.
- Rephrase the message to: "virtchnl: Too many VLAN [add|delete]
([v1|v2]) requests; splitting into multiple messages to PF\n".
Suggested-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Alok Tiwari <alok.a.tiwari@oracle.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20251125223632.1857532-12-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
- Fix a typo in the ice_fdir_has_frag() kernel-doc comment ("is" -> "if")
- Correct the NVM erase error message format string from "0x02%x" to
"0x%02x" so the module value is printed correctly.
Signed-off-by: Alok Tiwari <alok.a.tiwari@oracle.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20251125223632.1857532-11-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The error messages in idpf_rx_desc_alloc_all() used the group index i
when reporting memory allocation failures for individual Rx and Rx buffer
queues. This is incorrect.
Update the messages to use the correct queue index j and include the
queue group index i for clearer identification of the affected Rx and Rx
buffer queues.
Signed-off-by: Alok Tiwari <alok.a.tiwari@oracle.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20251125223632.1857532-10-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
idpf_compl_queue uses a union for comp, comp_4b, and desc_ring. The
release path should check complq->desc_ring to determine whether the DMA
descriptor ring is allocated. The current check against comp works but is
leftover from a previous commit and is misleading in this context.
Switching the check to desc_ring improves readability and more directly
reflects the intended meaning, since desc_ring is the field representing
the allocated DMA-backed descriptor ring.
No functional change.
Signed-off-by: Alok Tiwari <alok.a.tiwari@oracle.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20251125223632.1857532-9-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
ixgbe_non_sfp_link_config() is called twice in ixgbe_open()
once to assign its return value to err and again in the
conditional check. This patch uses the stored err value
instead of calling the function a second time. This avoids
redundant work and ensures consistent error reporting.
Also fix a small typo in the ixgbe_remove() comment:
"The could be caused" -> "This could be caused".
Signed-off-by: Alok Tiwari <alok.a.tiwari@oracle.com>
Reviewed-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20251125223632.1857532-8-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The caller, ethtool_set_eeprom(), already performs the same checks so
these are unnecessary in the driver. This reverts commit
90fb7db49c6d ("e1000e: fix heap overflow in e1000_set_eeprom"), however,
corrections for RCT have been kept.
Link: https://lore.kernel.org/all/db92fcc8-114d-4e85-9d15-7860545bc65e@suse.de/
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20251125223632.1857532-7-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Convert vport state to a bitmap and remove the DOWN state which is
redundant in the existing logic. There are no functional changes aside
from the use of bitwise operations when setting and checking the states.
Removed the double underscore to be consistent with the naming of other
bitmaps in the header and renamed current_state to vport_is_up to match
the meaning of the new variable.
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Chittim Madhu <madhu.chittim@intel.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Samuel Salin <Samuel.salin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20251125223632.1857532-6-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Flex array should be at the end of the structure and use [] syntax
Remove unused fields of ixgbevf_q_vector.
They aren't used since busy poll was moved to core code in commit
508aac6dee02 ("ixgbevf: get rid of custom busy polling code").
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Natalia Wochtman <natalia.wochtman@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20251125223632.1857532-5-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Convert the Cavium Thunder NIC VF driver to use the new .get_rx_ring_count
ethtool operation instead of implementing .get_rxnfc solely for handling
ETHTOOL_GRXRINGS command. This simplifies the code by removing the
switch statement and replacing it with a direct return of the queue
count.
The new callback provides the same functionality in a more direct way,
following the ongoing ethtool API modernization.
Signed-off-by: Breno Leitao <leitao@debian.org>
Link: https://patch.msgid.link/20251126-gxring_cavium-v1-1-a066c0c9e0c6@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The extra "count >= limit" check in stmmac_rx_zc() is redundant and
has no effect because the value of "count" doesn't change after the
while condition at this point.
However, it can change after "read_again:" label:
while (count < limit) {
...
if (count >= limit)
break;
read_again:
...
/* XSK pool expects RX frame 1:1 mapped to XSK buffer */
if (likely(status & rx_not_ls)) {
xsk_buff_free(buf->xdp);
buf->xdp = NULL;
dirty++;
count++;
goto read_again;
}
...
This patch addresses the same issue previously resolved in stmmac_rx()
by commit fa02de9e7588 ("net: stmmac: fix rx budget limit check").
The fix is the same: move the check after the label to ensure that it
bounds the goto loop.
Fixes: bba2556efad6 ("net: stmmac: Enable RX via AF_XDP zero-copy")
Signed-off-by: Alexey Kodanev <aleksei.kodanev@bell-sw.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/20251126104327.175590-1-aleksei.kodanev@bell-sw.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Extract MIB constants into the header file to improve code style. This
patch will not change the behavior of the function.
Signed-off-by: David Yang <mmyangfl@gmail.com>
Link: https://patch.msgid.link/20251126084024.2843851-3-mmyangfl@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There are hard-to-find unused fields in the MIB table I didn't notice in
the example driver code, causing wrong interpretation of the MIB data.
For some 64-bit attributes, the current (wrong) implementation took the
correct lower 32 bits, but messed up the upper 32 bits, so it would work
accidentally until 32-bit overflows happen. Fix that too.
Fixes: 186623f4aa72 ("net: dsa: yt921x: Add support for Motorcomm YT921x")
Signed-off-by: David Yang <mmyangfl@gmail.com>
Link: https://patch.msgid.link/20251126084024.2843851-2-mmyangfl@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This adds DASH support for chip RTL8127AP. Its mac version is
RTL_GIGA_MAC_VER_80. DASH is a standard for remote management of network
device, allowing out-of-band control.
Signed-off-by: Javen Xu <javen_xu@realsil.com.cn>
Link: https://patch.msgid.link/20251126055950.2050-1-javen_xu@realsil.com.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Neither sock4 nor sock6 pointers are guaranteed to be non-NULL in
vxlan_xmit_one, e.g. if the iface is brought down. This can lead to the
following NULL dereference:
BUG: kernel NULL pointer dereference, address: 0000000000000010
Oops: Oops: 0000 [#1] SMP NOPTI
RIP: 0010:vxlan_xmit_one+0xbb3/0x1580
Call Trace:
vxlan_xmit+0x429/0x610
dev_hard_start_xmit+0x55/0xa0
__dev_queue_xmit+0x6d0/0x7f0
ip_finish_output2+0x24b/0x590
ip_output+0x63/0x110
Mentioned commits changed the code path in vxlan_xmit_one and as a side
effect the sock4/6 pointer validity checks in vxlan(6)_get_route were
lost. Fix this by adding back checks.
Since both commits being fixed were released in the same version (v6.7)
and are strongly related, bundle the fixes in a single commit.
Reported-by: Liang Li <liali@redhat.com>
Fixes: 6f19b2c136d9 ("vxlan: use generic function for tunnel IPv4 route lookup")
Fixes: 2aceb896ee18 ("vxlan: use generic function for tunnel IPv6 route lookup")
Cc: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/20251126102627.74223-1-atenart@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
ptp_clock_settime() assumes every ptp_clock has implemented settime64().
Stub it with -EOPNOTSUPP to prevent a NULL dereference.
The fix is similar to commit 329d050bbe63 ("gve: Implement settime64
with -EOPNOTSUPP").
Fixes: d734223b2f0d ("iavf: add initial framework for registering PTP clock")
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Tim Hostetler <thostet@google.com>
Link: https://patch.msgid.link/20251126094850.2842557-1-mschmidt@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use DEFINE_RAW_FLEX() to avoid a -Wflex-array-member-not-at-end warning.
Remove fixed-size array struct usb_cdc_ncm_dpe16 dpe16[2]; from struct
mbim_tx_hdr, so that flex-array member struct mbim_tx_hdr::ndp16.dpe16[]
ends last in this structure.
Compensate for this by using the DEFINE_RAW_FLEX() helper to declare the
on-stack struct instance that contains struct usb_cdc_ncm_ndp16 as a
member. Adjust the rest of the code, accordingly.
So, with these changes fix the following warning:
drivers/net/wwan/mhi_wwan_mbim.c:81:34: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
Reviewed-by: Loic Poulain <loic.poulain@oss.qualcomm.com>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The tx->dropped_pkt counter is a 64-bit integer that is incremented
directly. On 32-bit architectures, this operation is not atomic and
can lead to read/write tearing if a reader accesses the counter during
the update. This can result in incorrect values being reported for
dropped packets.
To prevent this potential data corruption, wrap the increment
operation with u64_stats_update_begin() and u64_stats_update_end().
This ensures that updates to the 64-bit counter are atomic, even on
32-bit systems, by using a sequence lock.
The u64_stats_sync API requires the writer to have exclusive access,
which is already provided in this context by the network stack's
serialization of the transmit path (net_device_ops::ndo_start_xmit
[1]) for a given queue.
[1]: https://www.kernel.org/doc/Documentation/networking/netdevices.txt
Signed-off-by: Max Yuan <maxyuan@google.com>
Reviewed-by: Jordan Rhee <jordanrhee@google.com>
Signed-off-by: Harshitha Ramamurthy <hramamurthy@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As those following recent changes from Eric know very well
using NAPI skb cache is crucial to achieve good perf, at
least on recent AMD platforms. Make sure bnxt feeds the skb
cache with Tx skbs.
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Conflicts:
net/xdp/xsk.c
0ebc27a4c67d ("xsk: avoid data corruption on cq descriptor number")
8da7bea7db69 ("xsk: add indirect call for xsk_destruct_skb")
30ed05adca4a ("xsk: use a smaller new lock for shared pool case")
https://lore.kernel.org/20251127105450.4a1665ec@canb.auug.org.au
https://lore.kernel.org/eb4eee14-7e24-4d1b-b312-e9ea738fefee@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2025-11-26
this is a pull request of 27 patches for net-next/main.
The first 17 patches are by Vincent Mailhol and Oliver Hartkopp and
add CAN XL support to the CAN netlink interface.
Geert Uytterhoeven and Biju Das provide 7 patches for the rcar_canfd
driver to add suspend/resume support.
The next 2 patches are by Markus Schneider-Pargmann and add them as
the m_can maintainer.
Conor Dooley's patch updates the mpfs-can DT bindungs.
linux-can-next-for-6.19-20251126
* tag 'linux-can-next-for-6.19-20251126' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next: (27 commits)
dt-bindings: can: mpfs: document resets
MAINTAINERS: Simplify m_can section
MAINTAINERS: Add myself as m_can maintainer
can: rcar_canfd: Add suspend/resume support
can: rcar_canfd: Convert to DEFINE_SIMPLE_DEV_PM_OPS()
can: rcar_canfd: Invert CAN clock and close_candev() order
can: rcar_canfd: Extract rcar_canfd_global_{,de}init()
can: rcar_canfd: Use devm_clk_get_optional() for RAM clk
can: rcar_canfd: Invert global vs. channel teardown
can: rcar_canfd: Invert reset assert order
can: dev: print bitrate error with two decimal digits
can: raw: instantly reject unsupported CAN frames
can: add dummy_can driver
can: calc_bittiming: add can_calc_sample_point_pwm()
can: calc_bittiming: add can_calc_sample_point_nrz()
can: calc_bittiming: replace misleading "nominal" by "reference"
can: netlink: add PWM netlink interface
can: calc_bittiming: add PWM calculation
can: bittiming: add PWM validation
can: bittiming: add PWM parameters
...
====================
Link: https://patch.msgid.link/20251126120106.154635-1-mkl@pengutronix.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
In Store and Forward mode, flushing frames when the receive buffer is
unavailable, can cause the MTL Rx FIFO to go out of sync. This results
in buffering of a few frames in the FIFO without triggering Rx DMA
from transferring the data to the system memory until another packet
is received. Once the issue happens, for a ping request, the packet is
forwarded to the system memory only after we receive another packet
and hece we observe a latency equivalent to the ping interval.
64 bytes from 192.168.2.100: seq=1 ttl=64 time=1000.344 ms
Also, we can observe constant gmacgrp_debug register value of
0x00000120, which indicates "Reading frame data".
The issue is not reproducible after disabling frame flushing when Rx
buffer is unavailable. But in that case, the Rx DMA enters a suspend
state due to buffer unavailability. To resume operation, software
must write to the receive_poll_demand register after adding new
descriptors, which reactivates the Rx DMA.
This issue is observed in the socfpga platforms which has dwmac1000 IP
like Arria 10, Cyclone V and Agilex 7. Issue is reproducible after
running iperf3 server at the DUT for UDP lower packet sizes.
Signed-off-by: Rohan G Thomas <rohan.g.thomas@altera.com>
Reviewed-by: Matthew Gerlach <matthew.gerlach@altera.com>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/20251126-a10_ext_fix-v1-1-d163507f646f@altera.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
There are currently two situations that can trigger the PTP interrupt,
one is the PPS event, the other is the PEROUT event. However, the irq
handler fec_pps_interrupt() does not check the irq event type and
directly registers a PPS event into the system, but the event may be
a PEROUT event. This is incorrect because PEROUT is an output signal,
while PPS is the input of the kernel PPS system. Therefore, add a check
for the event type, if pps_enable is true, it means that the current
event is a PPS event, and then the PPS event is registered.
Fixes: 350749b909bf ("net: fec: Add support for periodic output signal of PPS")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Link: https://patch.msgid.link/20251125085210.1094306-5-wei.fang@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
In the current driver, PPS and PEROUT use the same channel to generate
the events, so they cannot be enabled at the same time. Otherwise, the
later configuration will overwrite the earlier configuration. Therefore,
when configuring PPS, the driver will check whether PEROUT is enabled.
Similarly, when configuring PEROUT, the driver will check whether PPS
is enabled.
Fixes: 350749b909bf ("net: fec: Add support for periodic output signal of PPS")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Link: https://patch.msgid.link/20251125085210.1094306-4-wei.fang@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
If the previously set PEROUT is already active, updating it will cause
the new PEROUT to start immediately instead of at the specified time.
This is because fep->reload_period is updated whithout check whether
the PEROUT is enabled, and the old PEROUT is not disabled. Therefore,
the pulse period will be updated immediately in the pulse interrupt
handler fec_pps_interrupt().
Currently, the driver does not support directly updating PEROUT and it
will make the logic be more complicated. To fix the current issue, add
a check before enabling the PEROUT, the driver will return an error if
PEROUT is enabled. If users wants to update a new PEROUT, they should
disable the old PEROUT first.
Fixes: 350749b909bf ("net: fec: Add support for periodic output signal of PPS")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Link: https://patch.msgid.link/20251125085210.1094306-3-wei.fang@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The PEROUT allows the user to set a specified future time to output the
periodic signal. If the future time is far from the current time, the FEC
driver will use hrtimer to configure PEROUT one second before the future
time. However, the hrtimer will not be canceled if the PEROUT is disabled
before the hrtimer expires. So the PEROUT will be configured when the
hrtimer expires, which is not as expected. Therefore, cancel the hrtimer
in fec_ptp_pps_disable() to fix this issue.
Fixes: 350749b909bf ("net: fec: Add support for periodic output signal of PPS")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Link: https://patch.msgid.link/20251125085210.1094306-2-wei.fang@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
As we have exposed the PCS registers via the SWMII we can now start looking
at connecting the XPCS driver to those registers and let it mange the PCS
instead of us doing it directly from the fbnic driver.
For now this just gets us the ability to detect link. The hope is in the
future to add some of the vendor specific registers to begin enabling XPCS
configuration of the interface.
Signed-off-by: Alexander Duyck <alexanderduyck@fb.com>
Link: https://patch.msgid.link/176374325295.959489.14521115864034905277.stgit@ahduyck-xeon-server.home.arpa
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
In order for us to support a PCS device we need to add an MDIO bus to allow
the drivers to have access to the registers for the device. This change
adds such an interface.
The interface will consist of 2 PHY addrs, the first one consisting of a
PMD and PCS, and the second just being a PCS. There is a need for 2 PHYs
addrs due to the fact that in order to support the 50GBase-CR2 mode we will
need to access and configure the PCS vendor registers and RSFEC registers
from the second lane identical to the first.
Signed-off-by: Alexander Duyck <alexanderduyck@fb.com>
Link: https://patch.msgid.link/176374324532.959489.15389723111560978054.stgit@ahduyck-xeon-server.home.arpa
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
We were previously not displaying the number of link_down_events tracked by
the device. With this change we should now be able to display the value.
The value itself tracks the calls from the phylink interface to the
mac_link_down call.
Signed-off-by: Alexander Duyck <alexanderduyck@fb.com>
Link: https://patch.msgid.link/176374323824.959489.6915296616773178954.stgit@ahduyck-xeon-server.home.arpa
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
One complication with the design of our part is that the PMD doesn't
provide a direct signal to the host. Instead we have visibility to signals
that the PCS provides to the MAC that allow us to check the link state
through that.
We will need to account for several things in the PMD and firmware when
managing the link. Specifically when the link first starts to come up the
PMD will cause the link to flap. This is due to the firmware starting a
training cycle when the link is first detected. This will cause link
flapping if we were to immediately report link up when the PCS first
detects it.
To address that we are adding a pmd_state variable that is meant to be a
countdown of sorts indicating the state of the PMD. If the link is down or
has been reconfigured the PMD will start out in the initialize state. By
default the link is assumed to be in the SEND_DATA state if it is available
on initial link inspection. If link is detected while in the initialize
state the PMD state will switch to training, and if after 4 seconds the
link is still stable we will transition to link_ready, and finally the
send_data state. With this we can avoid link flapping when a cable is
first connected to the NIC.
One side effect of this is that we need to pull the link state away from
the PCS. For now we use a union of the PCS link state register value and
the pmd_state. The plan is to add a PMD register to report the pmd_state
to the phylink interface. With that we can then look at switching over to
the use of the XPCS driver for fbnic instead of having an internal one.
Signed-off-by: Alexander Duyck <alexanderduyck@fb.com>
Link: https://patch.msgid.link/176374323107.959489.14951134213387615059.stgit@ahduyck-xeon-server.home.arpa
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
