| Age | Commit message (Collapse) | Author |
|---|
|
Now that stmmac's PCS support is much more simple - just a matter of
configuring the control register - the basic conversion to phylink PCS
support becomes straight forward.
Create the infrastructure to setup a phylink_pcs instance for the
integrated PCS:
- add a struct stmmac_pcs to encapsulate the phylink_pcs structure,
pointer to stmmac_priv, and the core-specific base address of the PCS
registers.
- modify stmmac_priv and stmmac_mac_select_pcs() to return the embedded
phylink_pcs structure when setup and STMMAC_PCS_SGMII is in use, and
move the comment from stmmac_hw_setup() to here.
- create stmmac_pcs.c, which contains the phylink_pcs_ops structure, a
dummy .pcs_get_state() method which always reports link-down, and
.pcs_config() method, moving the call to stmmac_pcs_ctrl_ane() here,
but without indirecting through the dwmac specific core code. The
link-down behaviour mentioned above maintains the current behaviour
when phylink is used with inband but without a PCS.
This will ensure that the PCS control register is configured to the
same settings as before, but will now happen when the netdev is opened
or reusmed rather than only during probe time. However, this will be
before the .fix_mac_speed() method is called, which is critical for the
behaviour in dwmac-qcom-ethqos's ethqos_configure_sgmii() function to
be maintained.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://patch.msgid.link/E1v9P72-0000000AomR-3ro4@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
dwmac cores provide a feature bit to indicate when the PCS block is
present, but features are only read after the core's setup() function
has been called, meaning we can't decide whether to initialise the
integrated PCS in the setup function. Provide a new MAC core hook
for PCS initialisation, which will be called after the feature
registers have been read.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://patch.msgid.link/E1v9P6x-0000000AomL-3OKd@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The internal PCS registers only exist if the core is synthesized with
SGMII, TBI or RTBI support. They have no relevance for RGMII.
However, priv->hw->pcs contains a STMMAC_PCS_RGMII flag, which is set
if a PCS has been synthesized but we are operating in RGMII mode. As
the register has no effect for RGMII, there is no point calling
stmmac_pcs_ctrl_ane() in this case. Add a comment describing this
and make it conditional on STMMAC_PCS_SGMII.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://patch.msgid.link/E1v9P6s-0000000AomE-2pAa@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
SGMII mode does not require port-speed to be specified; this only
switches SGMII to use the MAC configuration register speed settings
and the actual value is irrelevant when the link comes up.
As it seems the intention was to support "reverse SGMII" with this
setting, but the code didn't actually configure that due to a typo,
the warning and bad DT binding documentation has led people to
specify snps,ps-speed in their DT files inappropriately.
If mac_port_sel_speed is zero, then don't complain that the speed
is invalid, as this means we're using "normal" SGMII.
This does _not_ obsolete snps,ps-speed, nor does it change the
behaviour of that property, with the exception of not making people
mistakenly believe that they need to specify this option to use
normal SGMII. There is no need to modify the binding.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://patch.msgid.link/E1v9P6n-0000000Aom9-2LuZ@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
After a lot of digging, it seems that the oddly named hw->ps member
is all about setting the core into reverse SGMII speed. When set to
a non-zero value, it:
1. Configures the MAC at initialisation time to operate at a specific
speed.
2. It _incorrectly_ enables the transmitter (GMAC_CONFIG_TE) which
makes no sense, rather than enabling the "transmit configuration"
bit (GMAC_CONFIG_TC).
3. It configures the SGMII rate adapter layer to retrieve its speed
setting from the MAC configuration register rather than the PHY.
In the previous commit, we removed (1) and (2) as phylink overwrites
the configuration set at that step.
Thus, the only functional aspect is (3), which is a boolean operation.
This means there is no need to store the actual speed, and just have a
boolean flag.
Convert the priv->ps member to a boolean, and rename it to
priv->reverse_sgmii_enable to make it more understandable.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://patch.msgid.link/E1v9P6i-0000000Aom3-1y2y@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Now that we only support one mode, simplify stmmac_check_pcs_mode().
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://patch.msgid.link/E1v9P6d-0000000Aolw-1T7d@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The broken reverse-mode, selected by snps,ps-speed, is configured when
the platform provides a valid port speed and a PCS is being used.
Both these remain constant after the driver has probed, so the software
state doesn't need to be re-initialised each time stmmac_hw_setup() is
called (which is called at open and resume time.)
Move the software setup of reverse-mode to stmmac_check_pcs_mode()
which is called from the driver probe function.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://patch.msgid.link/E1v9P6Y-0000000Aolr-0vLH@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove the RGMII "pcs" code in stmmac_check_pcs_mode() due to:
1) This should never have been conditional on a PCS being present, as
when a core is synthesised using only RGMII, the PCS won't be present
and priv->dma_cap.pcs will be false. Only multi-interface cores which
have a PCS present would have detected RGMII.
2) STMMAC_PCS_RGMII has no effect since the broken netif_carrier and
ethtool code was removed.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://patch.msgid.link/E1v9P6T-0000000Aoll-0Ify@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
After a lot of digging, it seems that the oddly named hw->ps member is
all about configuring the core for reverse SGMII. This member is set to
one of 0, SPEED_10, SPEED_100 or SPEED_1000 depending on
priv->plat->mac_port_sel_speed. On DT systems, this comes from the
"snps,ps-speed" DT property.
When set to a non-zero value, it:
1. Configures the MAC at initialisation time to operate at a specific
speed. However, this will be overwritten by mac_link_up() when the
link comes up (e.g. with the fixed-link parameters.)
Note that dwxgmac2 wants to also support SPEED_2500 and SPEED_10000,
but both these values are impossible.
2. It _incorrectly_ enables the transmitter (GMAC_CONFIG_TE) which
makes no sense, rather than enabling the "transmit configuration"
bit (GMAC_CONFIG_TC). Likely a typo.
3. It configures the SGMII rate adapter layer to retrieve its speed
setting from the MAC configuration register rather than the PHY.
There are two ways forward here:
a) fixing (2) so that we set GMAC_CONFIG_TC. However, we have platform
that set the "snps,ps-speed" property and that work today. Fixing
this will cause the RGMII, SGMII or SMII inband configuration to be
transmitted, which will be a functional change which could cause a
regression.
b) ripping out (1) and (2) as they are ineffective. This also has the
possibility of regressions, but the patch author believes this risk
is much lower than (a).
Therefore, this commit takes the approach in (b).
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://patch.msgid.link/E1v9P6N-0000000Aolg-3y0a@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Nothing calls stmmac_pcs_ctrl_ane() with the "loopback" argument set to
anything except zero, so this serves no useful purpose. Remove the
argument to reduce the code complexity.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://patch.msgid.link/E1v9P6I-0000000Aola-3Sih@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove the "we always autoneg pause" forcing when the stmmac driver
decides that a "PCS" is present, which blocks passing the ethtool
pause calls to phylink when using SGMII mode.
This prevents the pause results being reported when a PHY is attached
using SGMII mode, or the pause settings being changed in SGMII mode.
There is no reason to prevent this.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://patch.msgid.link/E1v9P6D-0000000AolU-2zjv@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Now that the only use for the interrupt is to clear it and increment a
statistic counter (which is not that relevant anymore) remove all this
code and ensure that the interrupt remains disabled to avoid a stuck
interrupt.
dwmac-sun8i still uses this statistic counter, so it is inappropriate
for this patch to remove it.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://patch.msgid.link/E1v9P68-0000000AolO-2W5s@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As a result of the previous commit, the pcs_link, pcs_duplex and
pcs_speed members are not used outside of the interrupt handling code,
and are only used to print their status using the misleading "Link is"
messages that bear no relation to the actual status of the link.
Remove the printing of these messages, these members, and the code
that decodes them from the hardware.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://patch.msgid.link/E1v9P63-0000000AolI-23Kf@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Changing the netif_carrier_*() state behind phylink's back has always
been prohibited because it messes up with phylinks state tracking, and
means that phylink no longer guarantees to call the mac_link_down()
and mac_link_up() methods at the appropriate times. This was later
documented in the sfp-phylink network driver conversion guide.
stmmac was converted to phylink in 2019, but nothing was done with the
"PCS" code. Since then, apart from the updates as part of phylink
development, nothing has happened with stmmac to improve its use of
phylink, or even to address this point.
A couple of years ago, a has_integrated_pcs boolean was added by Bart,
which later became the STMMAC_FLAG_HAS_INTEGRATED_PCS flag, to avoid
manipulating the netif_carrier_*() state. This flag is mis-named,
because whenever the stmmac is synthesized for its native SGMII, TBI
or RTBI interfaces, it has an "integrated PCS". This boolean/flag
actually means "ignore the status from the integrated PCS".
Discussing with Bart, the reasons for this are lost to the winds of
time (which is why we should always document the reasons in the commit
message.)
RGMII also has in-band status, and the dwmac cores and stmmac code
supports this but with one bug that saves the day.
When dwmac cores are synthesised for RGMII only, they do not contain
an integrated PCS, and so priv->dma_cap.pcs is clear, which prevents
(incorrectly) the "RGMII PCS" being used, meaning we don't read the
in-band status. However, a core synthesised for RGMII and also SGMII,
TBI or RTBI will have this capability bit set, thus making these
code paths reachable.
The Jetson Xavier NX uses RGMII mode to talk to its PHY, and removing
the incorrect check for priv->dma_cap.pcs reveals the theortical issue
with netif_carrier_*() manipulation is real:
dwc-eth-dwmac 2490000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-0
dwc-eth-dwmac 2490000.ethernet eth0: PHY [stmmac-0:00] driver [RTL8211F Gigabit Ethernet] (irq=141)
dwc-eth-dwmac 2490000.ethernet eth0: No Safety Features support found
dwc-eth-dwmac 2490000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
dwc-eth-dwmac 2490000.ethernet eth0: registered PTP clock
dwc-eth-dwmac 2490000.ethernet eth0: configuring for phy/rgmii-id link mode
8021q: adding VLAN 0 to HW filter on device eth0
dwc-eth-dwmac 2490000.ethernet eth0: Adding VLAN ID 0 is not supported
Link is Up - 1000/Full
Link is Down
Link is Up - 1000/Full
This looks good until one realises that the phylink "Link" status
messages are missing, even when the RJ45 cable is reconnected. Nothing
one can do results in the interface working. The interrupt handler
(which prints those "Link is" messages) always wins over phylink's
resolve worker, meaning phylink never calls the mac_link_up() nor
mac_link_down() methods.
eth0 also sees no traffic received, and is unable to obtain a DHCP
address:
3: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group defa
ult qlen 1000
link/ether e6:d3:6a:e6:92:de brd ff:ff:ff:ff:ff:ff
RX: bytes packets errors dropped overrun mcast
0 0 0 0 0 0
TX: bytes packets errors dropped carrier collsns
27686 149 0 0 0 0
With the STMMAC_FLAG_HAS_INTEGRATED_PCS flag set, which disables the
netif_carrier_*() manipulation then stmmac works normally:
dwc-eth-dwmac 2490000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-0
dwc-eth-dwmac 2490000.ethernet eth0: PHY [stmmac-0:00] driver [RTL8211F Gigabit Ethernet] (irq=141)
dwc-eth-dwmac 2490000.ethernet eth0: No Safety Features support found
dwc-eth-dwmac 2490000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
dwc-eth-dwmac 2490000.ethernet eth0: registered PTP clock
dwc-eth-dwmac 2490000.ethernet eth0: configuring for phy/rgmii-id link mode
8021q: adding VLAN 0 to HW filter on device eth0
dwc-eth-dwmac 2490000.ethernet eth0: Adding VLAN ID 0 is not supported
Link is Up - 1000/Full
dwc-eth-dwmac 2490000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
and packets can be transferred.
This clearly shows that when priv->hw->pcs is set, but
STMMAC_FLAG_HAS_INTEGRATED_PCS is clear, the driver reliably fails.
Discovering whether a platform falls into this is impossible as
parsing all the dtsi and dts files to find out which use the stmmac
driver, whether any of them use RGMII or SGMII and also depends
whether an external interface is being used. The kernel likely
doesn't contain all dts files either.
The only driver that sets this flag uses the qcom,sa8775p-ethqos
compatible, and uses SGMII or 2500BASE-X.
but these are saved from this problem by the incorrect check for
priv->dma_cap.pcs.
So, we have to assume that for every other platform that uses SGMII
with stmmac is using an external PCS.
Moreover, ethtool output can be incorrect. With the full-duplex link
negotiated, ethtool reports:
Speed: 1000Mb/s
Duplex: Half
because with dwmac4, the full-duplex bit is in bit 16 of the status,
priv->xstats.pcs_duplex becomes BIT(16) for full duplex, but the
ethtool ksettings duplex member is u8 - so becomes zero. Moreover,
the supported, advertised and link partner modes are all "not
reported".
Finally, ksettings_set() won't be able to set the advertisement on
a PHY if this PCS code is activated, which is incorrect when SGMII
is used with a PHY.
Thus, remove:
1. the incorrect netif_carrier_*() manipulation.
2. the broken ethtool ksettings code.
Given that all uses of STMMAC_FLAG_HAS_INTEGRATED_PCS are now gone,
remove the flag from stmmac.h and dwmac-qcom-ethqos.c.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://patch.msgid.link/E1v9P5y-0000000AolC-1QWH@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix several spelling and grammatical errors in comments across
micrel PHY drivers. Corrections include:
- "dealy" -> "delay"
- "autonegotation" -> "autonegotiation"
- "recheas" -> "reaches"
- "one" -> "on"
- "improvenent" -> "improvement"
- "intput" -> "input"
Signed-off-by: Alok Tiwari <alok.a.tiwari@oracle.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20251017193525.1457064-2-alok.a.tiwari@oracle.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
ksz9477_phy_errata function currently assigns the return value of
genphy_restart_aneg() to a variable and then immediately returns it
err = genphy_restart_aneg(phydev);
if (err)
return err;
return err;
This can be simplified by directly returning the function call
result, as the intermediate variable and conditional are redundant.
Signed-off-by: Alok Tiwari <alok.a.tiwari@oracle.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20251017193525.1457064-1-alok.a.tiwari@oracle.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Since the commit c1f3f9797c1f ("can: netlink: can_changelink(): fix NULL
pointer deref of struct can_priv::do_set_mode"), the automatic restart
delay can only be set for devices that implement the restart handler struct
can_priv::do_set_mode. As it makes no sense to configure a automatic
restart for devices that doesn't support it.
However, since systemd commit 13ce5d4632e3 ("network/can: properly handle
CAN.RestartSec=0") [1], systemd-networkd correctly handles a restart delay
of "0" (i.e. the restart is disabled). Which means that a disabled restart
is always configured in the kernel.
On systems with both changes active this causes that CAN interfaces that
don't implement a restart handler cannot be brought up by systemd-networkd.
Solve this problem by allowing a delay of "0" to be configured, even if the
device does not implement a restart handler.
[1] https://github.com/systemd/systemd/commit/13ce5d4632e395521e6205c954493c7fc1c4c6e0
Cc: stable@vger.kernel.org
Cc: Andrei Lalaev <andrey.lalaev@gmail.com>
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Closes: https://lore.kernel.org/all/20251020-certain-arrogant-vole-of-sunshine-141841-mkl@pengutronix.de
Fixes: c1f3f9797c1f ("can: netlink: can_changelink(): fix NULL pointer deref of struct can_priv::do_set_mode")
Link: https://patch.msgid.link/20251020-netlink-fix-restart-v1-1-3f53c7f8520b@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
of can_dropped_invalid_skb()
In addition to can_dropped_invalid_skb(), the helper function
can_dev_dropped_skb() checks whether the device is in listen-only mode and
discards the skb accordingly.
Replace can_dropped_invalid_skb() by can_dev_dropped_skb() to also drop
skbs in for listen-only mode.
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Closes: https://lore.kernel.org/all/20251017-bizarre-enchanted-quokka-f3c704-mkl@pengutronix.de/
Fixes: ff60bfbaf67f ("can: rockchip_canfd: add driver for Rockchip CAN-FD controller")
Link: https://patch.msgid.link/20251017-fix-skb-drop-check-v1-3-556665793fa4@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
can_dropped_invalid_skb()
In addition to can_dropped_invalid_skb(), the helper function
can_dev_dropped_skb() checks whether the device is in listen-only mode and
discards the skb accordingly.
Replace can_dropped_invalid_skb() by can_dev_dropped_skb() to also drop
skbs in for listen-only mode.
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Closes: https://lore.kernel.org/all/20251017-bizarre-enchanted-quokka-f3c704-mkl@pengutronix.de/
Fixes: 9721866f07e1 ("can: esd: add support for esd GmbH PCIe/402 CAN interface family")
Link: https://patch.msgid.link/20251017-fix-skb-drop-check-v1-2-556665793fa4@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
can_dropped_invalid_skb()
In addition to can_dropped_invalid_skb(), the helper function
can_dev_dropped_skb() checks whether the device is in listen-only mode and
discards the skb accordingly.
Replace can_dropped_invalid_skb() by can_dev_dropped_skb() to also drop
skbs in for listen-only mode.
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Closes: https://lore.kernel.org/all/20251017-bizarre-enchanted-quokka-f3c704-mkl@pengutronix.de/
Fixes: f00647d8127b ("can: bxcan: add support for ST bxCAN controller")
Link: https://patch.msgid.link/20251017-fix-skb-drop-check-v1-1-556665793fa4@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
Miri Korenblit says:
====================
iwlwifi fix
avoid use after free
====================
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Currently, whenever there is a need to transmit an Action frame,
the brcmfmac driver always uses the P2P vif to send the "actframe" IOVAR to
firmware. The P2P interfaces were available when wpa_supplicant is managing
the wlan interface.
However, the P2P interfaces are not created/initialized when only hostapd
is managing the wlan interface. And if hostapd receives an ANQP Query REQ
Action frame even from an un-associated STA, the brcmfmac driver tries
to use an uninitialized P2P vif pointer for sending the IOVAR to firmware.
This NULL pointer dereferencing triggers a driver crash.
[ 1417.074538] Unable to handle kernel NULL pointer dereference at virtual
address 0000000000000000
[...]
[ 1417.075188] Hardware name: Raspberry Pi 4 Model B Rev 1.5 (DT)
[...]
[ 1417.075653] Call trace:
[ 1417.075662] brcmf_p2p_send_action_frame+0x23c/0xc58 [brcmfmac]
[ 1417.075738] brcmf_cfg80211_mgmt_tx+0x304/0x5c0 [brcmfmac]
[ 1417.075810] cfg80211_mlme_mgmt_tx+0x1b0/0x428 [cfg80211]
[ 1417.076067] nl80211_tx_mgmt+0x238/0x388 [cfg80211]
[ 1417.076281] genl_family_rcv_msg_doit+0xe0/0x158
[ 1417.076302] genl_rcv_msg+0x220/0x2a0
[ 1417.076317] netlink_rcv_skb+0x68/0x140
[ 1417.076330] genl_rcv+0x40/0x60
[ 1417.076343] netlink_unicast+0x330/0x3b8
[ 1417.076357] netlink_sendmsg+0x19c/0x3f8
[ 1417.076370] __sock_sendmsg+0x64/0xc0
[ 1417.076391] ____sys_sendmsg+0x268/0x2a0
[ 1417.076408] ___sys_sendmsg+0xb8/0x118
[ 1417.076427] __sys_sendmsg+0x90/0xf8
[ 1417.076445] __arm64_sys_sendmsg+0x2c/0x40
[ 1417.076465] invoke_syscall+0x50/0x120
[ 1417.076486] el0_svc_common.constprop.0+0x48/0xf0
[ 1417.076506] do_el0_svc+0x24/0x38
[ 1417.076525] el0_svc+0x30/0x100
[ 1417.076548] el0t_64_sync_handler+0x100/0x130
[ 1417.076569] el0t_64_sync+0x190/0x198
[ 1417.076589] Code: f9401e80 aa1603e2 f9403be1 5280e483 (f9400000)
Fix this, by always using the vif corresponding to the wdev on which the
Action frame Transmission request was initiated by the userspace. This way,
even if P2P vif is not available, the IOVAR is sent to firmware on AP vif
and the ANQP Query RESP Action frame is transmitted without crashing the
driver.
Move init_completion() for "send_af_done" from brcmf_p2p_create_p2pdev()
to brcmf_p2p_attach(). Because the former function would not get executed
when only hostapd is managing wlan interface, and it is not safe to do
reinit_completion() later in brcmf_p2p_tx_action_frame(), without any prior
init_completion().
And in the brcmf_p2p_tx_action_frame() function, the condition check for
P2P Presence response frame is not needed, since the wpa_supplicant is
properly sending the P2P Presense Response frame on the P2P-GO vif instead
of the P2P-Device vif.
Cc: stable@vger.kernel.org
Fixes: 18e2f61db3b7 ("brcmfmac: P2P action frame tx")
Signed-off-by: Gokul Sivakumar <gokulkumar.sivakumar@infineon.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Link: https://patch.msgid.link/20251013102819.9727-1-gokulkumar.sivakumar@infineon.com
[Cc stable]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ath/ath
Jeff Johnson says:
==================
ath.git update for v6.18-rc1
Fix memory leaks in both ath10k and ath12k.
Fix a sparse issue in ath11k.
Allow ath11k suspend/resume to work on more Lenovo laptops.
==================
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This code frees "link" by calling kfree_rcu(link, rcu_head) and then it
dereferences "link" to get the "link->fw_id". Save the "link->fw_id"
first to avoid a potential use after free.
Fixes: d1e879ec600f ("wifi: iwlwifi: add iwlmld sub-driver")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://patch.msgid.link/aNKCcKlbSkkS4_gO@stanley.mountain
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
|
|
Some systems such as live-image or installer require the firmware
information for each module declared by MODULE_FIRMWARE(), which is
currently missing in ath12k driver.
For addressing it, this patch adds the MODULE_FIRMWARE() entries.
Like ath11k driver, we can just put the currently used firmware
entries for QCN9274 and WCN7850 with wildcards.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20251003082955.11436-1-tiwai@suse.de
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Documentation/networking/switchdev.rst says that VLAN-aware bridges must
treat packets tagged with VID 0 the same as untagged. It appears from
the documentation that setting the GSWIP_PCE_VCTRL_VID0 flag (which this
driver already had defined) might achieve this.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://patch.msgid.link/b220ac149922839a261b754202c05df5bb253c98.1760566491.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Implement the required functionality, as written in
Documentation/networking/switchdev.rst section "Bridge VLAN filtering",
by using the "VLAN Ingress Tag Rule" feature of the switch.
The bit field definitions for this were found while browsing the Intel
dual BSD/GPLv2 licensed drivers for this switch IP.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://patch.msgid.link/787aa807d00b726d75db2a40add215c8b8ba7466.1760566491.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
gswip_vlan_remove()
Improve the error message printed in case of a port VLAN entry not being
found upon removal.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://patch.msgid.link/abd4ec58e0f0f53eb3d7027097a20af0bd7b1d6d.1760566491.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
gswip_vlan_remove()
"bool pvid" is unused since commit "net: dsa: lantiq_gswip: remove
legacy configure_vlan_while_not_filtering option".
"bool vlan_aware" shouldn't have a role in finding the bridge VLAN.
It should be identified by VID regardless of VLAN-aware or VLAN-unaware.
The driver sets up VID 0 for the VLAN-unaware PVID.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://patch.msgid.link/c63f89ca19269ef6c8bf00a62cacc739164b4441.1760566491.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
User space can force the altering of VID 0 as it was privately set up by
this driver.
For example, when the port joins a VLAN-aware bridge,
dsa_user_manage_vlan_filtering() will set NETIF_F_HW_VLAN_CTAG_FILTER.
If the port is subsequently brought up and CONFIG_VLAN_8021Q is enabled,
the vlan_vid0_add() function will want to make sure we are capable of
accepting packets tagged with VID 0.
Generally, DSA/switchdev drivers want to suppress that bit of help from
the 8021q layer, and handle VID 0 filters themselves. The 8021q layer
might actually be even detrimential, because VLANs added through
vlan_vid_add() pass through dsa_user_vlan_rx_add_vid(), which is
documented as this:
/* This API only allows programming tagged, non-PVID VIDs */
.flags = 0,
so it will force VID 0 to be reconfigured as egress-tagged, non-PVID.
Whereas the driver configures it as PVID and egress-untagged, the exact
opposite.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://patch.msgid.link/9f68340c34b5312c3b8c6c7ecf3cfce574a3f65d.1760566491.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The driver should now tolerate these changes, now that the PVID is
automatically recalculated on a VLAN awareness state change.
The VLAN-unaware PVID must be installed to hardware even if the
joined bridge is currently VLAN-aware. Otherwise, when the bridge VLAN
filtering state dynamically changes to VLAN-unaware later, this PVID
will be missing.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://patch.msgid.link/c58759074fb699581336dc2c2c6bf106257b134e.1760566491.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This driver doesn't support dynamic VLAN filtering changes, for simplicity.
It expects that on a port, either gswip_vlan_add_unaware() or
gswip_vlan_add_aware() is called, but not both.
When !br_vlan_enabled(), the configure_vlan_while_not_filtering = false
option is exactly what will prevent calls to gswip_port_vlan_add() from
being issued by DSA.
In fact, at the time these features were submitted:
https://patchwork.ozlabs.org/project/netdev/patch/20190501204506.21579-3-hauke@hauke-m.de/
"configure_vlan_while_not_filtering = false" did not even have a name,
it was implicit behaviour. It only became legacy in commit 54a0ed0df496
("net: dsa: provide an option for drivers to always receive bridge
VLANs").
Section "Bridge VLAN filtering" of Documentation/networking/switchdev.rst
describes the exact set of rules. Notably, the PVID of the port must
follow the VLAN awareness state of the bridge port. A VLAN-unaware
bridge port should not respond to the addition of a bridge VLAN with the
PVID flag. In fact, the pvid_change() test in
tools/testing/selftests/net/forwarding/bridge_vlan_unaware.sh tests
exactly this.
The lantiq_gswip driver indeed does not respond to the addition of PVID
VLANs while VLAN-unaware in the way described above, but only because of
configure_vlan_while_not_filtering. Our purpose here is to get rid of
configure_vlan_while_not_filtering, so we must add more complex logic
which follows the VLAN awareness state and walks through the Active VLAN
table entries, to find the index of the PVID register that should be
committed to hardware on each port.
As a side-effect of now having a proper implementation to assign the
PVID all the "VLAN upper: ..." tests of the local_termination.sh self-
tests which would previously all FAIL now all PASS (or XFAIL, but
that's ok).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Link: https://patch.msgid.link/47dab8a8b69ebb92624b9795b723114475d3fe4e.1760566491.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
gswip_vlan_add_aware()
The two functions largely duplicate functionality. The differences
consist in:
- the "fid" passed to gswip_vlan_active_create(). The unaware variant
always passes -1, the aware variant passes fid = priv->vlans[i].fid,
where i is an index into priv->vlans[] for which priv->vlans[i].bridge
is equal to the given bridge.
- the "vid" is not passed to gswip_vlan_add_unaware(). It is implicitly
GSWIP_VLAN_UNAWARE_PVID (zero).
- The "untagged" is not passed to gswip_vlan_add_unaware(). It is
implicitly true. Also, the CPU port must not be a tag member of the
PVID used for VLAN-unaware bridging.
- The "pvid" is not passed to gswip_vlan_add_unaware(). It is implicitly
true.
- The GSWIP_PCE_DEFPVID(port) register is written by the aware variant
with an "idx", but with a hardcoded 0 by the unaware variant.
Merge the two functions into a single unified function without any
functional changes.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://patch.msgid.link/2be190701d4c17038ce4b8047f9fb0bdf8abdf6e.1760566491.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When idx == -1 in gswip_vlan_add(), we set vlan_mapping.val[0] = vid,
even though we do the exact same thing again outside the if/else block.
Remove the duplicate assignment.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://patch.msgid.link/039ecb48e038cea856a9a6230ad1543db2bc382d.1760566491.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This patch adds an explicit definition for VID 0 to the Lantiq GSWIP DSA
driver, clarifying its special meaning.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://patch.msgid.link/e8862239d0bb727723cf60947d2262473b46c96d.1760566491.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, the driver takes the bridge from dsa_port_bridge_dev_get(),
which only works for user ports. This is why it has to ignore FDB
entries installed on the CPU port.
Commit c26933639b54 ("net: dsa: request drivers to perform FDB
isolation") introduced the possibility of getting the originating bridge
from the passed dsa_db argument, so let's do that instead. This way, we
can act on the local FDB entries coming from the bridge.
Note that we do not expect FDB events for the DSA_DB_PORT database,
because this driver doesn't fulfill the dsa_switch_supports_uc_filtering()
requirements. So we can just return -EOPNOTSUPP and expect it will never
be triggered.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://patch.msgid.link/ed9d847c0356f0fec81422bdad9ebdcc6a59da79.1760566491.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There's a good chance that more chip versions suffer from the same
hw issue. So let's reconfigure rx unconditionally before the chip reset
when resuming. This shouldn't have any side effect on unaffected chip
versions.
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/a5c2e2d2-226f-4896-b8f6-45e2d91f0e24@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When splitting the RTL8221B-VM-CG into C22 and C45 variants, the name was
accidentally changed to RTL8221B-VN-CG. This patch brings back the previous
part number.
Fixes: ad5ce743a6b0 ("net: phy: realtek: Add driver instances for rtl8221b via Clause 45")
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251016192325.2306757-1-olek2@wp.pl
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The blamed commit increased the needed headroom to account for
alignment. This means that the size required to always align a Tx buffer
was added inside the dpaa2_eth_needed_headroom() function. By doing
that, a manual adjustment of the pointer passed to PTR_ALIGN() was no
longer correct since the 'buffer_start' variable was already pointing
to the start of the skb's memory.
The behavior of the dpaa2-eth driver without this patch was to drop
frames on Tx even when the headroom was matching the 128 bytes
necessary. Fix this by removing the manual adjust of 'buffer_start' from
the PTR_MODE call.
Closes: https://lore.kernel.org/netdev/70f0dcd9-1906-4d13-82df-7bbbbe7194c6@app.fastmail.com/T/#u
Fixes: f422abe3f23d ("dpaa2-eth: increase the needed headroom to account for alignment")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251016135807.360978-1-ioana.ciornei@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This patch fixes ce7a381697cb ("net: bonding: add broadcast_neighbor option for 802.3ad").
Before this commit, on the broadcast mode, all devices were traversed using the
bond_for_each_slave_rcu. This patch supports traversing devices by using all_slaves.
Therefore, we need to update the slave array when enslave or release slave.
Fixes: ce7a381697cb ("net: bonding: add broadcast_neighbor option for 802.3ad")
Cc: Simon Horman <horms@kernel.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Andrew Lunn <andrew+netdev@lunn.ch>
Cc: <stable@vger.kernel.org>
Reported-by: Jiri Slaby <jirislaby@kernel.org>
Tested-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/all/a97e6e1e-81bc-4a79-8352-9e4794b0d2ca@kernel.org/
Signed-off-by: Tonghao Zhang <tonghao@bamaicloud.com>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Acked-by: Jay Vosburgh <jv@jvosburgh.net>
Link: https://patch.msgid.link/20251016125136.16568-1-tonghao@bamaicloud.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The ENETC RX ring uses the page halves flipping mechanism, each page is
split into two halves for the RX ring to use. And ENETC_RXB_TRUESIZE is
defined to 2048 to indicate the size of half a page. However, the page
size is configurable, for ARM64 platform, PAGE_SIZE is default to 4K,
but it could be configured to 16K or 64K.
When PAGE_SIZE is set to 16K or 64K, ENETC_RXB_TRUESIZE is not correct,
and the RX ring will always use the first half of the page. This is not
consistent with the description in the relevant kernel doc and commit
messages.
This issue is invisible in most cases, but if users want to increase
PAGE_SIZE to receive a Jumbo frame with a single buffer for some use
cases, it will not work as expected, because the buffer size of each
RX BD is fixed to 2048 bytes.
Based on the above two points, we expect to correct ENETC_RXB_TRUESIZE
to (PAGE_SIZE >> 1), as described in the comment.
Fixes: d4fd0404c1c9 ("enetc: Introduce basic PF and VF ENETC ethernet drivers")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Link: https://patch.msgid.link/20251016080131.3127122-1-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
After applying the workaround for err050089, the LS1028A platform
experiences RCU stalls on RT kernel. This issue is caused by the
recursive acquisition of the read lock enetc_mdio_lock. Here list some
of the call stacks identified under the enetc_poll path that may lead to
a deadlock:
enetc_poll
-> enetc_lock_mdio
-> enetc_clean_rx_ring OR napi_complete_done
-> napi_gro_receive
-> enetc_start_xmit
-> enetc_lock_mdio
-> enetc_map_tx_buffs
-> enetc_unlock_mdio
-> enetc_unlock_mdio
After enetc_poll acquires the read lock, a higher-priority writer attempts
to acquire the lock, causing preemption. The writer detects that a
read lock is already held and is scheduled out. However, readers under
enetc_poll cannot acquire the read lock again because a writer is already
waiting, leading to a thread hang.
Currently, the deadlock is avoided by adjusting enetc_lock_mdio to prevent
recursive lock acquisition.
Fixes: 6d36ecdbc441 ("net: enetc: take the MDIO lock only once per NAPI poll cycle")
Signed-off-by: Jianpeng Chang <jianpeng.chang.cn@windriver.com>
Acked-by: Wei Fang <wei.fang@nxp.com>
Link: https://patch.msgid.link/20251015021427.180757-1-jianpeng.chang.cn@windriver.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In {tcp6,udp6,raw6}_sock, struct ipv6_pinfo is always placed at
the beginning of a new cache line because
1. __alignof__(struct tcp_sock) is 64 due to ____cacheline_aligned
of __cacheline_group_begin(tcp_sock_write_tx)
2. __alignof__(struct udp_sock) is 64 due to ____cacheline_aligned
of struct numa_drop_counters
3. in raw6_sock, struct numa_drop_counters is placed before
struct ipv6_pinfo
. struct ipv6_pinfo is 136 bytes, but the last cache line is
only used by ipv6_fl_list:
$ pahole -C ipv6_pinfo vmlinux
struct ipv6_pinfo {
...
/* --- cacheline 2 boundary (128 bytes) --- */
struct ipv6_fl_socklist * ipv6_fl_list; /* 128 8 */
/* size: 136, cachelines: 3, members: 23 */
Let's move ipv6_fl_list from struct ipv6_pinfo to struct inet_sock
to save a full cache line for {tcp6,udp6,raw6}_sock.
Now, struct ipv6_pinfo is 128 bytes, and {tcp6,udp6,raw6}_sock have
64 bytes less, while {tcp,udp,raw}_sock retain the same size.
Before:
# grep -E "^(RAW|UDP[^L\-]|TCP)" /proc/slabinfo | awk '{print $1, "\t", $4}'
RAWv6 1408
UDPv6 1472
TCPv6 2560
RAW 1152
UDP 1280
TCP 2368
After:
# grep -E "^(RAW|UDP[^L\-]|TCP)" /proc/slabinfo | awk '{print $1, "\t", $4}'
RAWv6 1344
UDPv6 1408
TCPv6 2496
RAW 1152
UDP 1280
TCP 2368
Also, ipv6_fl_list and inet_flags (SNDFLOW bit) are placed in the
same cache line.
$ pahole -C inet_sock vmlinux
...
/* --- cacheline 11 boundary (704 bytes) was 56 bytes ago --- */
struct ipv6_pinfo * pinet6; /* 760 8 */
/* --- cacheline 12 boundary (768 bytes) --- */
struct ipv6_fl_socklist * ipv6_fl_list; /* 768 8 */
unsigned long inet_flags; /* 776 8 */
Doc churn is due to the insufficient Type column (only 1 space short).
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Link: https://patch.msgid.link/20251014224210.2964778-1-kuniyu@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
support pci_driver.shutdown() for hibmcge driver.
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Link: https://patch.msgid.link/20251014134018.1178385-1-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
is down
If the interface is down, the CAN controller might be powered down, the
clock disabled, and/or it's external reset asserted.
Don't wake up the controller to read the CAN bus error counters, if the
interface is down.
Reviewed-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://patch.msgid.link/20251008-m_can-cleanups-v1-7-1784a18eaa84@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
m_can_tx_submit() is only called for peripheral devices. So remove the
sanity check.
Link: https://patch.msgid.link/20251008-m_can-cleanups-v1-6-1784a18eaa84@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
devm_kzalloc() fails
If devm_kzalloc() fails, it already outputs an error message. Remove the
error message from m_can_class_register() accordingly.
Link: https://patch.msgid.link/20251008-m_can-cleanups-v1-5-1784a18eaa84@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
coding it
As everywhere else in the driver, use m_can_write() instead of open coding
it.
Link: https://patch.msgid.link/20251008-m_can-cleanups-v1-4-1784a18eaa84@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
To ease debugging use the netdev_{dbg,info,err}() functions instead of
dev_{dbg,info,err}.
Link: https://patch.msgid.link/20251008-m_can-cleanups-v1-3-1784a18eaa84@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The original use of struct m_can_classdev::hrtimer was to support polling
for devices without IRQ, with the timer function called hrtimer_callback().
Commit 07f25091ca02 ("can: m_can: Implement receive coalescing") uses the
hrtimer for software-supported IRQ coalescence, with the timer function
called m_can_coalescing_timer().
To improve the readability of the driver, rename hrtimer_callback() to
m_can_polling_timer(), which better describes the functionality.
Link: https://patch.msgid.link/20251008-m_can-cleanups-v1-2-1784a18eaa84@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
