| Age | Commit message (Collapse) | Author |
|---|
|
The register-save-restore debugfs prints whitelist entries as offset
ranges. E.g.,
REG[0x39319c-0x39319f]: allow read access
for a single dword-sized register. However the GENMASK value used to
set the lower bits to '1' for the upper bound of the whitelist range
incorrectly included one more bit than it should have, causing the
whitelist ranges to sometimes appear twice as large as they really were.
For example,
REG[0x6210-0x6217]: allow rw access
was also intended to be a single dword-sized register whitelist (with a
range 0x6210-0x6213) but was printed incorrectly as a qword-sized range
because one too many bits was flipped on. Similar 'off by one' logic
was applied when printing 4-dword register ranges and 64-dword register
ranges as well.
Correct the GENMASK logic to print these ranges in debugfs correctly.
No impact outside of correcting the misleading debugfs output.
Fixes: d855d2246ea6 ("drm/xe: Print whitelist while applying")
Reviewed-by: Stuart Summers <stuart.summers@intel.com>
Link: https://patch.msgid.link/20260408-regsr_wl_range-v1-1-e9a28c8b4264@intel.com
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
|
|
ROW_CHICKEN5 is a masked register (i.e., to adjust the value of any of
the lower 16 bits, the corresponding bit in the upper 16 bits must also
be set). Add the XE_REG_OPTION_MASKED to its definition; failure to do
so will cause workaround updates of this register to not apply properly.
Bspec: 56853
Fixes: 835cd6cbb0d0 ("drm/xe/xe3p_lpg: Add initial workarounds for graphics version 35.10")
Reviewed-by: Gustavo Sousa <gustavo.sousa@intel.com>
Link: https://patch.msgid.link/20260410-xe3p_tuning-v1-3-e206a62ee38f@intel.com
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
|
|
From Xe2 onward (i.e., all platforms officially supported by the Xe
driver), the GAMSTLB_CTRL register is located at offset 0x477C and
represented by the macro "GAMSTLB_CTRL" in code. However the register
formerly resided at offset 0xCF4C on Xe1-era platforms, and we also have
macro XEHP_GAMSTLB_CTRL that represents this old offset in the
unofficial/developer-only Xe1 code. When tuning for the register was
added for Xe3p_LPG, the old Xe1-era macro was accidentally used instead
of the proper macro for Xe2 and beyond, causing the tuning to not be
applied properly. Use the proper definition so that the correct offset
is written to.
Bspec: 59298
Fixes: 377c89bfaa5d ("drm/xe/xe3p_lpg: Set STLB bank hash mode to 4KB")
Reviewed-by: Gustavo Sousa <gustavo.sousa@intel.com>
Link: https://patch.msgid.link/20260410-xe3p_tuning-v1-2-e206a62ee38f@intel.com
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
|
|
Whereas the tuning guide gave guidance on adjusting various CCCHKNREG1
on past platforms, starting from Xe3p the guidance is "Leave register at
HW default settings." Set a version range upper bound of "34.99" so
that the current programming will stop being applied on any Xe3p
platforms that have graphics version 35.
Bspec: 72161
Reviewed-by: Gustavo Sousa <gustavo.sousa@intel.com>
Link: https://patch.msgid.link/20260410-xe3p_tuning-v1-1-e206a62ee38f@intel.com
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs
Pull vfs i_ino updates from Christian Brauner:
"For historical reasons, the inode->i_ino field is an unsigned long,
which means that it's 32 bits on 32 bit architectures. This has caused
a number of filesystems to implement hacks to hash a 64-bit identifier
into a 32-bit field, and deprives us of a universal identifier field
for an inode.
This changes the inode->i_ino field from an unsigned long to a u64.
This shouldn't make any material difference on 64-bit hosts, but
32-bit hosts will see struct inode grow by at least 4 bytes. This
could have effects on slabcache sizes and field alignment.
The bulk of the changes are to format strings and tracepoints, since
the kernel itself doesn't care that much about the i_ino field. The
first patch changes some vfs function arguments, so check that one out
carefully.
With this change, we may be able to shrink some inode structures. For
instance, struct nfs_inode has a fileid field that holds the 64-bit
inode number. With this set of changes, that field could be
eliminated. I'd rather leave that sort of cleanups for later just to
keep this simple"
* tag 'vfs-7.1-rc1.kino' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs:
nilfs2: fix 64-bit division operations in nilfs_bmap_find_target_in_group()
EVM: add comment describing why ino field is still unsigned long
vfs: remove externs from fs.h on functions modified by i_ino widening
treewide: fix missed i_ino format specifier conversions
ext4: fix signed format specifier in ext4_load_inode trace event
treewide: change inode->i_ino from unsigned long to u64
nilfs2: widen trace event i_ino fields to u64
f2fs: widen trace event i_ino fields to u64
ext4: widen trace event i_ino fields to u64
zonefs: widen trace event i_ino fields to u64
hugetlbfs: widen trace event i_ino fields to u64
ext2: widen trace event i_ino fields to u64
cachefiles: widen trace event i_ino fields to u64
vfs: widen trace event i_ino fields to u64
net: change sock.sk_ino and sock_i_ino() to u64
audit: widen ino fields to u64
vfs: widen inode hash/lookup functions to u64
|
|
__fsdev_dax_direct_access() returns -EFAULT without setting *kaddr when
dax_pgoff_to_phys() returns -1 (pgoff out of range). The return value
was ignored, leaving kaddr uninitialized before being passed to
fsdev_write_dax().
Check the return value and propagate the error.
Thanks to Dan Carpenter and the smatch project for reporting this.
Signed-off-by: John Groves <john@groves.net>
Reviewed-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Link: https://patch.msgid.link/0100019d8262cda2-9714d31c-8fc1-4ca5-b32d-4df678240d14-000000@email.amazonses.com
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
|
|
Currently we take the Hail Mary RGB fallback for "4:2:0 only" modes
already during the first pass when respect_downstream_limits==true.
It seems better to try everything else first (like ignoring TMDS
clock limits) while still preferring 4:2:0, and only if everything
else has failed fall back to RGB.
Cc: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20260409101539.22032-10-ville.syrjala@linux.intel.com
Tested-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
|
|
Currently we take the Hail Mary RGB fallback for "4:2:0 only" modes
already during the first pass when respect_downstream_limits==true.
It seems better to try everything else first (like ignoring TMDS
clock limits) while still preferring 4:2:0, and only if everything
else has failed fall back to RGB.
Cc: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20260409101539.22032-9-ville.syrjala@linux.intel.com
Tested-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
|
|
Make sure the sink supports our chosen sink format. I suppose it
might be at least possible that some PCONs might not snoop the EDID
hard enough and filter out all the modes that they should.
Also if we ever want to add a similar "force DVI" knob to DP
outputs that we have for native HDMI, we'd need to manually
get rid of anything DVI sinks can't handle.
Cc: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20260409101539.22032-8-ville.syrjala@linux.intel.com
Tested-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
|
|
DVI sinks can't deal with YCbCr. Make sure we have a HDMI sink connected
after the PCON before doing YCbCr 4:2:0 output.
Cc: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20260409101539.22032-7-ville.syrjala@linux.intel.com
Tested-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
|
|
Currently we only validate "4:2:0 also" modes as RGB. But
if that fails we could perhaps still use the mode in with
4:2:0 output. All we have to do is retry the validation with
the different sink format.
So far we did the double validation only so far as it affects
PCON TMDS clock limits. But validating everything twice seems
a bit more sane.
Note that intel_dp_output_format() might still end up picking
RGB for the actual output format (and letting PCON deal with
the YCbCr conversion). So I suppose we could still fail the
validation due to that, and forcing even the output format
to 4:2:0 might solve it on a third try. But we'd need the
same fallback logic in intel_dp_compute_config(). For now
this seems sufficient.
v2: Pass output_format to intel_dp_mode_min_link_bpp_x16()
Add TODO about remaining issues
Nuke intel_dp_sink_format()
Cc: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20260409101539.22032-6-ville.syrjala@linux.intel.com
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Tested-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
|
|
Restructure intel_dp_compute_output_format() to resemble the new
intel_hdmi_compute_output_formats().
Again, we basically have two main code paths:
- YCbCr 4:2:0 only modes
- everything else including YCbCr 4:2:0 also modes
Take the exact same approach with the DP code, making the
format selection much less convoluted.
Cc: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Cc: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20260409101539.22032-5-ville.syrjala@linux.intel.com
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Tested-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
|
|
Restructure the HDMI mode validation to resemble the new
intel_hdmi_compute_formats(). Keeping the two in sync helps
to avoid different bugs in each.
The main difference between mode_valid() and
intel_hdmi_compute_formats() is that we don't want the
Hail Mary RGB fallback for "4:2:0 only" modes.
Cc: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20260409101539.22032-4-ville.syrjala@linux.intel.com
Tested-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
|
|
intel_hdmi_compute_output_format() is a bit of a mess. Try to
restructure it into a more readable form.
Right now we basically have two main code paths:
- YCbCr 4:2:0 only modes
- everything else including YCbCr 4:2:0 also modes
Those two basically do the same two steps (try 4:2:0 and try 4:4:4)
but in opposite orders. Let's write that out in a more explicit
if-else form. And since I'm running out of function names I'll
rename the function with that high level logic into
intel_hdmi_compute_formats() and it will call (the new)
intel_hdmi_compute_output_format() with an explicit sink_format
as needed.
Cc: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20260409101539.22032-3-ville.syrjala@linux.intel.com
Tested-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
|
|
intel_hdmi_mode_valid() is calling intel_pfit_mode_valid() only
on the first attempt (4:2:0 for "4:2:0 only" modes, 4:4:4 for
everything else). Add the call also for the "4:2:0 also" modes case
so that we actually know the pipe scaler can actually produce the
4:2:0 output.
Cc: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20260409101539.22032-2-ville.syrjala@linux.intel.com
Tested-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
|
|
- Warn only once about invalid ACS kernel parameter format (Richard Cheng)
- Suppress FW_BUG warning when writing sysfs 'numa_node' with the current
value (Li RongQing)
- Drop redundant 'depends on PCI' from Kconfig (Julian Braha)
* pci/misc:
PCI: Clean up dead code in Kconfig
PCI/sysfs: Suppress FW_BUG warning when NUMA node already matches
PCI: Use pr_warn_once() for ACS parameter parse failure
PCI: of: Reduce severity of missing of_root error message
|
|
- Assert (not deassert) resets in probe error path (John Madieu)
- Assert resets in suspend path in reverse order they were deasserted
during probe (John Madieu)
- Rework inbound window algorithm to prevent mapping more than intended
region and enforce alignment on size, to prepare for RZ/G3E support (John
Madieu)
- Fix renesas,r9a08g045s33-pcie 'serr_cor' typo and convert properties from
'description' to 'const' for better validation (John Madieu)
- Add RZ/G3E to DT binding and to driver (John Madieu)
* pci/controller/rzg3s-host:
PCI: rzg3s-host: Add support for RZ/G3E PCIe controller
PCI: rzg3s-host: Add PCIe Gen3 (8.0 GT/s) link speed support
PCI: rzg3s-host: Explicitly set class code for RZ/G3E compatibility
PCI: rzg3s-host: Add SoC-specific configuration and initialization callbacks
PCI: rzg3s-host: Make configuration reset lines optional
PCI: rzg3s-host: Make SYSC register offsets SoC-specific
dt-bindings: PCI: renesas,r9a08g045s33-pcie: Document RZ/G3E SoC
dt-bindings: PCI: renesas,r9a08g045s33-pcie: Fix naming properties
PCI: rzg3s-host: Rework inbound window algorithm for supporting RZ/G3E SoC
PCI: rzg3s-host: Reorder reset assertion during suspend
PCI: rzg3s-host: Fix reset handling in probe error path
# Conflicts:
# drivers/pci/controller/pcie-rzg3s-host.c
|
|
- Use dev_err_probe() to simplify error paths and make deferred probe
messages visible in /sys/kernel/debug/devices_deferred (Chen-Yu Tsai)
- Initialize IRQ domains earlier to remove need for cleanup if it fails
(Chen-Yu Tsai)
- Set up controller windows and MSI before bringing the link up to separate
controller init and things related to downstream devices (Chen-Yu Tsai)
- Split out device power up and down helpers (Chen-Yu Tsai)
- Power off device if setup fails (Chen-Yu Tsai)
- Integrate new pwrctrl API to enable power control for WiFi/BT adapters on
mainboard or in PCIe or M.2 slots (Chen-Yu Tsai)
- Prevent leaking IRQ domains when IRQ not found (Chen-Yu Tsai)
* pci/controller/mediatek-gen3:
PCI: mediatek-gen3: Prevent leaking IRQ domains when IRQ not found
PCI: mediatek-gen3: Integrate new pwrctrl API
PCI: mediatek-gen3: Disable device if further setup fails
PCI: mediatek-gen3: Split out device power helpers
PCI: mediatek-gen3: Add error path for resume driver callbacks
PCI: mediatek-gen3: Move controller setup steps before PERST# control
PCI: mediatek-gen3: Move mtk_pcie_setup_irq() out of mtk_pcie_setup()
PCI: mediatek-gen3: Clean up mtk_pcie_parse_port() with dev_err_probe()
|
|
- Increase snprintf() buffer size to avoid truncation warnings (Ryder Lee)
* pci/controller/mediatek:
PCI: mediatek: Fix possible truncation in mtk_pcie_parse_port()
|
|
- Poll less aggressively and non-atomically for PME_TO_Ack during
transition to L2 (Vidya Sagar)
- Increase LTSSM poll time on surprise link down (Manikanta Maddireddy)
- Disable LTSSM after transition to Detect on surprise link down to stop
toggling between Polling and Detect (Manikanta Maddireddy)
- Don't force the device into the D0 state before L2 when suspending or
shutting down the controller (Vidya Sagar)
- Disable PERST# IRQ only in Endpoint mode because it's not registered in
Root Port mode (Manikanta Maddireddy)
- Handle 'nvidia,refclk-select' as optional (Vidya Sagar)
- Disable direct speed change in Endpoint mode so link speed change is
controlled by the host (Vidya Sagar)
- Set LTR values before link up to avoid bogus LTR messages with 0 latency
(Vidya Sagar)
- Allow system suspend when the Endpoint link is down (Vidya Sagar)
- During remove, free resources allocated during Endpoint .probe() (Vidya
Sagar)
- Use DWC IP core version, not Tegra custom values, to avoid DWC core
version check warnings (Manikanta Maddireddy)
- Apply ECRC workaround to devices based on DesignWare 5.00a as well
as 4.90a (Manikanta Maddireddy)
- Disable PM Substate L1.2 in Endpoint mode to work around Tegra234 erratum
(Vidya Sagar)
- Delay post-PERST# cleanup until core is powered on to avoid CBB timeout
(Manikanta Maddireddy)
- Assert CLKREQ# so switches that forward it to their downstream side can
bring up those links successfully (Vidya Sagar)
- Calibrate pipe to UPHY for Endpoint mode to reset stale PLL state from
any previous bad link state (Vidya Sagar)
- Remove IRQF_ONESHOT flag from Endpoint interrupt registration so DMA
driver and Endpoint controller driver can share the interrupt line (Vidya
Sagar)
- Enable DMA interrupt to support DMA in both Root Port and Endpoint modes
(Vidya Sagar)
- Enable hardware link retraining after link goes down in Endpoint mode
(Vidya Sagar)
- Add DT binding and driver support for core clock monitoring (Vidya Sagar)
* pci/controller/dwc-tegra194:
PCI: tegra194: Add core monitor clock support
dt-bindings: PCI: tegra194: Add monitor clock support
PCI: tegra194: Enable hardware hot reset mode in Endpoint mode
PCI: tegra194: Enable DMA interrupt
PCI: tegra194: Remove IRQF_ONESHOT flag during Endpoint interrupt registration
PCI: tegra194: Calibrate pipe to UPHY for Endpoint mode
PCI: tegra194: Assert CLKREQ# explicitly by default
PCI: tegra194: Fix CBB timeout caused by DBI access before core power-on
PCI: tegra194: Disable L1.2 capability of Tegra234 EP
PCI: dwc: Apply ECRC workaround to DesignWare 5.00a as well
PCI: tegra194: Use DWC IP core version
PCI: tegra194: Free up Endpoint resources during remove()
PCI: tegra194: Allow system suspend when the Endpoint link is not up
PCI: tegra194: Set LTR message request before PCIe link up in Endpoint mode
PCI: tegra194: Disable direct speed change for Endpoint mode
PCI: tegra194: Use devm_gpiod_get_optional() to parse "nvidia,refclk-select"
PCI: tegra194: Disable PERST# IRQ only in Endpoint mode
PCI: tegra194: Don't force the device into the D0 state before L2
PCI: tegra194: Disable LTSSM after transition to Detect on surprise link down
PCI: tegra194: Increase LTSSM poll time on surprise link down
PCI: tegra194: Fix polling delay for L2 state
|
|
- Add tracepoints for PCIe controller LTSSM transitions and link rate
changes (Shawn Lin)
- Trace LTSSM events collected by the dw-rockchip debug FIFO (Shawn Lin)
* pci/controller/dwc-rockchip:
PCI: dw-rockchip: Add pcie_ltssm_state_transition tracepoint support
Documentation: tracing: Add PCI controller event documentation
PCI: trace: Add PCI controller tracepoint feature
|
|
- Mark BAR0 and BAR2 as Resizable (Koichiro Den)
- Reduce EPC BAR alignment requirement to 4K (Koichiro Den)
* pci/controller/dwc-rcar-gen4-ep:
PCI: dwc: rcar-gen4: Change EPC BAR alignment to 4K as per the documentation
PCI: dwc: rcar-gen4: Mark BAR0 and BAR2 as Resizable BARs in endpoint mode
# Conflicts:
# drivers/pci/controller/dwc/pcie-rcar-gen4.c
|
|
- Advertise 'Hot-Plug Capable' and set 'No Command Completed Support' since
Qcom Root Ports support hotplug events like DL_Up/Down and can accept
writes to Slot Control without delays between writes (Krishna Chaitanya
Chundru)
* pci/controller/dwc-qcom:
PCI: qcom: Advertise Hotplug Slot Capability with no Command Completion support
|
|
- Allow Layerscape host controller driver to be build as a removable module
(Sascha Hauer)
* pci/controller/dwc-layerscape:
PCI: layerscape: Allow to compile as module
|
|
- Fix device node reference leak in imx_pcie_probe() (Felix Gu)
- Delay instead of polling for L2/L3 Ready after PME_Turn_off when
suspending i.MX6SX because LTSSM registers are inaccessible (Richard Zhu)
- Separate PERST# assertion (for resetting endpoints) from core reset (for
resetting the RC itself) to prepare for new DTs with PERST# GPIO in
per-Root Port nodes (Sherry Sun)
- Retain the Root Port MSI capability on i.MX7D, i.MX8MM, and i.MX8MQ so
MSI from downstream devices will work (Richard Zhu)
- Fix the i.MX95 reference clock source selection when internal refclk is
used (Franz Schnyder)
* pci/controller/dwc-imx6:
PCI: imx6: Fix reference clock source selection for i.MX95
PCI: imx6: Keep Root Port MSI capability with iMSI-RX to work around hardware bug
PCI: imx6: Separate PERST# assertion from core reset functions
PCI: imx6: Change imx_pcie_deassert_core_reset() return type to void
PCI: imx6: Skip waiting for L2/L3 Ready on i.MX6SX
PCI: imx6: Fix device node reference leak in imx_pcie_probe()
|
|
- Add DT binding and driver for ESWIN PCIe Root Complex (Senchuan Zhang)
* pci/controller/dwc-eswin:
PCI: eswin: Add ESWIN PCIe Root Complex driver
dt-bindings: PCI: eswin: Add ESWIN PCIe Root Complex
# Conflicts:
# drivers/pci/controller/dwc/Kconfig
# drivers/pci/controller/dwc/Makefile
|
|
- Add Andes QiLai SoC PCIe host driver support (Randolph Lin)
* pci/controller/dwc-andes-qilai:
PCI: qilai: Add Andes QiLai SoC PCIe host driver support
dt-bindings: PCI: Add Andes QiLai PCIe support
# Conflicts:
# drivers/pci/controller/dwc/Makefile
|
|
- Correct the IRQ number logged in INTx error message (Rakuram Eswaran)
* pci/controller/dwc-amd-mdb:
PCI: amd-mdb: Correct IRQ number in INTx error message
|
|
- Continue with system suspend even if an Endpoint doesn't respond with
PME_TO_Ack message (Manivannan Sadhasivam)
- Remove the Baikal-T1 controller driver since it never quite became usable
(Andy Shevchenko)
- Set Endpoint MSI-X Table Size in the correct function of a multi-function
device when configuring MSI-X, not in Function 0 (Aksh Garg)
- Set Max Link Width and Max Link Speed for all functions of a
multi-function device, not just Function 0 (Aksh Garg)
- Clean up in the dw_pcie_resume_noirq() error path (Manivannan Sadhasivam)
- Expose PCIe event counters in groups 5-7 in debugfs (Hans Zhang)
- Fix type mismatch for kstrtou32_from_user() in debugfs write functions
(Hans Zhang)
* pci/controller/dwc:
PCI: dwc: Fix type mismatch for kstrtou32_from_user() return value
PCI: dwc: Expose PCIe event counters for groups 5 to 7 over debugfs
PCI: dwc: Perform cleanup in the error path of dw_pcie_resume_noirq()
PCI: dwc: ep: Mirror the max link width and speed fields to all functions
PCI: dwc: ep: Fix MSI-X Table Size configuration in dw_pcie_ep_set_msix()
PCI: dwc: Remove not-going-to-be-supported code for Baikal SoC
PCI: dwc: Proceed with system suspend even if the endpoint doesn't respond with PME_TO_Ack message
|
|
- Release ECAM config on probe failure (Felix Gu)
* pci/controller/cadence-sky1:
PCI: sky1: Use boolean true for is_rc field
PCI: sky1: Fix missing cleanup of ECAM config on probe failure
|
|
- Add cadence core flags to disable advertising broken ASPM support (Yao
Zi)
- Disable ASPM L0s and L1 on Sophgo 2042 PCIe Root Ports that advertise
support for them (Yao Zi)
* pci/controller/cadence-sg2042:
PCI: sg2042: Avoid L0s and L1 on Sophgo 2042 PCIe Root Ports
PCI: cadence: Add flags for disabling ASPM capability for broken Root Ports
|
|
- Implement byte/word config reads with dword (32-bit) reads because some
Cadence controllers don't support sub-dword accesses (Aksh Garg)
* pci/controller/cadence:
PCI: cadence: Use cdns_pcie_read_sz() for byte or word read access
|
|
- Fix IRQ domain leak on platform_get_irq() failure (Felix Gu)
* pci/controller/aspeed:
PCI: aspeed: Fix IRQ domain leak on platform_get_irq() failure
|
|
- Add pcie_get_link_speed() to encapsulate and bounds-check
pcie_link_speed[] accesses (Hans Zhang)
- Validate max-link-speed from DT in j721e, brcmstb, mediatek-gen3, rzg3s
(where the actual controller constraints are known), and remove it from
the generic OF DT accessor (Hans Zhang)
* pci/controller/max-link-speed:
PCI: of: Remove max-link-speed generation validation
PCI: controller: Validate max-link-speed
PCI: j721e: Validate max-link-speed from DT
PCI: dwc: Use pcie_get_link_speed() helper for safe array access
PCI: Add pcie_get_link_speed() helper for safe array access
|
|
- Free all previously requested IRQs in epf_ntb_db_bar_init_msi_doorbell()
error path (Koichiro Den)
- Free doorbell IRQ in pci-epf-test only if it has actually been requested
(Koichiro Den)
- Discard pointer to doorbell message array after freeing it in
pci_epf_alloc_doorbell() error path (Koichiro Den)
- Advertise dynamic inbound mapping support in pci-epf-test and update host
pci_endpoint_test to skip doorbell testing if not advertised by endpoint
(Koichiro Den)
- Constify configfs item and group operations (Christophe JAILLET)
- Use array_index_nospec() on configfs MW show/store attributes (Koichiro
Den)
- Return -ERANGE (not -EINVAL) for configfs out-of-range MW index (Koichiro
Den)
- Return 0, not remaining timeout, when MHI eDMA ops complete so
mhi_ep_ring_add_element() doesn't interpret non-zero as failure (Daniel
Hodges)
- Remove vntb and ntb duplicate resource teardown that leads to oops when
.allow_link() fails or .drop_link() is called (Koichiro Den)
- Disable vntb delayed work before clearing BAR mappings and doorbells to
avoid oops caused by doing the work after resources have been torn down
(Koichiro Den)
- Fix pci_epf_add_vepf() kernel-doc typo (Alok Tiwari)
- Propagate pci_epf_create() errors to pci_epf_make() callers (Alok Tiwari)
- Remove redundant BAR_RESERVED annotation for the high order part of a
64-bit BAR (Niklas Cassel)
- Add a way to describe reserved subregions within BARs, e.g.,
platform-owned fixed register windows, and use it for the RK3588 BAR4 DMA
ctrl window (Koichiro Den)
- Add BAR_DISABLED for BARs that will never be available to an EPF driver,
and change some BAR_RESERVED annotations to BAR_DISABLED (Niklas Cassel)
- Disable BARs in common code instead of in each glue driver (Niklas
Cassel)
- Advertise reserved BARs in Capabilities so host-side drivers can skip
them (Niklas Cassel)
- Skip reserved BARs in selftests (Niklas Cassel)
- Improve error messages and include device name when available (Manivannan
Sadhasivam)
- Add NTB .get_dma_dev() callback for cases where DMA API requires a
different device, e.g., vNTB devices (Koichiro Den)
- Return -EINVAL, not -ENOSPC, if endpoint test determines the subrange
size is too small (Koichiro Den)
- Add reserved region types for MSI-X Table and PBA so Endpoint controllers
can them as describe hardware-owned regions in a BAR_RESERVED BAR
(Manikanta Maddireddy)
- Make Tegra194/234 BAR0 programmable and remove 1MB size limit (Manikanta
Maddireddy)
- Expose Tegra BAR2 (MSI-X) and BAR4 (DMA) as 64-bit BAR_RESERVED
(Manikanta Maddireddy)
- Add Tegra194 and Tegra234 device table entries to pci_endpoint_test
(Manikanta Maddireddy)
- Skip the BAR subrange selftest if there are not enough inbound window
resources to run the test (Christian Bruel)
* pci/endpoint:
selftests: pci_endpoint: Skip BAR subrange test on -ENOSPC
misc: pci_endpoint_test: Add Tegra194 and Tegra234 device table entries
PCI: tegra194: Expose BAR2 (MSI-X) and BAR4 (DMA) as 64-bit BAR_RESERVED
PCI: tegra194: Make BAR0 programmable and remove 1MB size limit
PCI: endpoint: Add reserved region type for MSI-X Table and PBA
misc: pci_endpoint_test: Use -EINVAL for small subrange size
PCI: endpoint: pci-epf-vntb: Implement .get_dma_dev()
NTB: ntb_transport: Use ntb_get_dma_dev() for DMA buffers
NTB: core: Add .get_dma_dev() callback to ntb_dev_ops
PCI: endpoint: Improve error messages
PCI: endpoint: Print the EPF name in the error log of pci_epf_make()
selftests: pci_endpoint: Skip reserved BARs
misc: pci_endpoint_test: Give reserved BARs a distinct error code
PCI: endpoint: pci-epf-test: Advertise reserved BARs
PCI: dwc: Disable BARs in common code instead of in each glue driver
PCI: dwc: Replace certain BAR_RESERVED with BAR_DISABLED in glue drivers
PCI: endpoint: Introduce pci_epc_bar_type BAR_DISABLED
PCI: dw-rockchip: Describe RK3588 BAR4 DMA ctrl window
PCI: endpoint: Describe reserved subregions within BARs
PCI: endpoint: Allow only_64bit on BAR_RESERVED
PCI: endpoint: Do not mark the BAR succeeding a 64-bit BAR as BAR_RESERVED
PCI: endpoint: Propagate error from pci_epf_create()
PCI: endpoint: Fix typo in pci_epf_add_vepf() kernel-doc
PCI: endpoint: pci-epf-vntb: Stop cmd_handler work in epf_ntb_epc_cleanup
PCI: endpoint: pci-epf-ntb: Remove duplicate resource teardown
PCI: endpoint: pci-epf-vntb: Remove duplicate resource teardown
PCI: epf-mhi: Return 0, not remaining timeout, when eDMA ops complete
PCI: endpoint: pci-epf-vntb: Return -ERANGE for out-of-range MW index
PCI: endpoint: pci-epf-vntb: Use array_index_nospec() on mws_size[] access
PCI: endpoint: Constify struct configfs_item_operations and configfs_group_operations
selftests: pci_endpoint: Skip doorbell test when unsupported
misc: pci_endpoint_test: Gate doorbell test on dynamic inbound mapping
PCI: endpoint: pci-epf-test: Advertise dynamic inbound mapping support
PCI: endpoint: pci-ep-msi: Fix error unwind and prevent double alloc
PCI: endpoint: pci-epf-test: Don't free doorbell IRQ unless requested
PCI: endpoint: pci-epf-vntb: Fix MSI doorbell IRQ unwind
|
|
- Avoid FLR for AMD NPU device, where it causes the device to hang (Lizhi
Hou)
* pci/virtualization:
PCI: Avoid FLR for AMD NPU device
|
|
- Return vga_get_uninterruptible() back to userspace in the
/dev/vga_arbiter path so user can tell whether VGA routing was updated
(Simon Richter)
- Make pci_set_vga_state() fail if bridge doesn't support VGA routing,
i.e., PCI_BRIDGE_CTL_VGA is not writable, and return errors up to
vga_get() callers (Simon Richter)
* pci/vga:
PCI/VGA: Fail pci_set_vga_state() if VGA decoding not supported
PCI/VGA: Pass errors from pci_set_vga_state() up
PCI/VGA: Pass vga_get_uninterruptible() errors to userspace
|
|
- Prevent assigning space to unimplemented bridge windows; previously we
mistakenly assumed prefetchable window existed and assigned space and put
a BAR there (Ahmed Naseef)
- Avoid shrinking bridge windows to fit in the initial Root Port window;
this fixes one problem with devices with large BARs connected via
switches, e.g., Thunderbolt (Ilpo Järvinen)
- Retain information about optional resources to make assignment during
rescan more likely to succeed (Ilpo Järvinen)
- Add __resource_contains_unbound() for use in finding space for resources
with no address assigned (Ilpo Järvinen)
- Pass full extent of empty space, not just the aligned space, to
resource_alignf callback so free space before the requested alignment can
be used (Ilpo Järvinen)
- Remove unnecessary second alignment from ARM, m68k, MIPS (Ilpo Järvinen)
- Place small resources before larger ones for better utilization of
address space (Ilpo Järvinen)
- Fix alignment calculation for resource size larger than align, e.g.,
bridge windows larger than the 1MB required alignment (Ilpo Järvinen)
* pci/resource:
PCI: Fix alignment calculation for resource size larger than align
PCI: Align head space better
PCI: Rename window_alignment() to pci_min_window_alignment()
parisc/PCI: Clean up align handling
MIPS: PCI: Remove unnecessary second application of align
m68k/PCI: Remove unnecessary second application of align
ARM/PCI: Remove unnecessary second application of align
resource: Rename 'tmp' variable to 'full_avail'
resource: Pass full extent of empty space to resource_alignf callback
resource: Add __resource_contains_unbound() for internal contains checks
PCI: Fix premature removal from realloc_head list during resource assignment
PCI: Prevent shrinking bridge window from its required size
PCI: Prevent assignment to unsupported bridge windows
|
|
- Update slot handling so all ARI functions are treated as being in the
same slot. They're all reset by Secondary Bus Reset, but previously
drivers of ARI functions that appeared to be on a non-zero device weren't
notified and fatal hardware errors could result (Keith Busch)
- Make sysfs reset_subordinate hotplug safe to avoid spurious hotplug
events (Keith Busch)
- Consolidate bus iteration across the _lock(), _unlock(), and _trylock()
functions for pci_bus and pci_slot (Ilpo Järvinen)
- Hide Secondary Bus Reset ('bus') from sysfs reset_methods if masked by
CXL because it has no effect (Vidya Sagar)
* pci/reset:
PCI/CXL: Hide SBR from reset_methods if masked by CXL
PCI: Consolidate pci_bus/slot_lock/unlock/trylock()
PCI: Make reset_subordinate hotplug safe
PCI: Allow all bus devices to use the same slot
PCI: Rename __pci_bus_reset() and __pci_slot_reset()
|
|
- Rename 'slot' driver to 'generic' since it can handle any device with
individual power control as well as slots (Neil Armstrong)
- Add UPD720201/UPD720202 USB 3.0 xHCI Host Controller .compatible so
generic pwrctrl driver can control it (Neil Armstrong)
* pci/pwrctrl:
PCI/pwrctrl: generic: Add UPD720201/UPD720202 USB 3.0 xHCI Host Controller support
PCI/pwrctrl: generic: Simplify dev_err_probe() usage
PCI/pwrctrl: generic: Rename pci-pwrctrl-slot as generic
|
|
- Leave Precision Time Measurement disabled until a driver enables it to
avoid PCIe errors (Mika Westerberg)
* pci/ptm:
PCI/PTM: Do not enable PTM automatically for Root and Switch Upstream Ports
PCI/PTM: Drop pci_enable_ptm() granularity parameter
|
|
- Allow wildcards in list of host bridges that support peer-to-peer DMA
between hierarchy domains and add all Google SoCs (Jacob Moroni)
* pci/p2pdma:
PCI/P2PDMA: Add Google SoCs to the P2P DMA host bridge list
PCI/P2PDMA: Allow wildcard Device IDs in host bridge list
|
|
- Update documentation of pci_free_irq_vectors() and pcim_enable_device()
(Shawn Lin)
* pci/msi:
PCI/MSI: Add TODO comment about legacy pcim_enable_device() side-effect
PCI/MSI: Clarify pci_free_irq_vectors() usage for managed devices
|
|
- Use for_each_child_of_node_scoped() to simplify iteration over OF
children (Krzysztof Kozlowski)
- Set LED_HW_PLUGGABLE for NPEM hotplug-capable ports so LED core doesn't
complain when setting brightness fails because the endpoint is gone
(Richard Cheng)
* pci/hotplug:
PCI/NPEM: Set LED_HW_PLUGGABLE for hotplug-capable ports
PCI: rpaphp: Simplify with scoped for each OF child loop
PCI: pnv_php: Simplify with scoped for each OF child loop
|
|
- Allow TPH to be enabled for RCiEPs (George Abraham P)
- Remove the pc110pad since 486 CPU support is being removed (Dmitry
Torokhov)
- Remove no_pci_devices() since pc110pad was the last remaining user
(Heiner Kallweit)
* pci/enumeration:
PCI: Remove no_pci_devices()
Input: pc110pad - remove driver
PCI/TPH: Allow TPH enable for RCiEPs
|
|
- Hold a pci_dev reference during error recovery (Sizhe Liu)
- Initialize ratelimit info so DPC and EDR paths log AER error information
(Kuppuswamy Sathyanarayanan)
* pci/dpc:
PCI/DPC: Log AER error info for DPC/EDR uncorrectable errors
PCI/DPC: Hold pci_dev reference during error recovery
|
|
- Don't enable AtomicOps by RCiEPs since none of them need Atomic Ops and
we can't tell whether the Root Complex would support them (Gerd Bayer)
- Enable AtomicOps only if we know the Root Port supports them (Gerd Bayer)
* pci/atomics:
PCI: Update PCIe spec references for AtomicOps
PCI: Enable AtomicOps only if Root Port supports them
PCI: Do not enable AtomicOps by RCiEPs
|
|
- Fix ASPM usage of pci_clear_and_set_config_dword() to prevent
inadvertently setting Common_Mode_Restore_Time and other fields (Lukas
Wunner)
* pci/aspm:
PCI/ASPM: Fix pci_clear_and_set_config_dword() usage
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs
Pull vfs integrity updates from Christian Brauner:
"This adds support to generate and verify integrity information (aka
T10 PI) in the file system, instead of the automatic below the covers
support that is currently used.
The implementation is based on refactoring the existing block layer PI
code to be reusable for this use case, and then adding relatively
small wrappers for the file system use case. These are then used in
iomap to implement the semantics, and wired up in XFS with a small
amount of glue code.
Compared to the baseline this does not change performance for writes,
but increases read performance up to 15% for 4k I/O, with the benefit
decreasing with larger I/O sizes as even the baseline maxes out the
device quickly on my older enterprise SSD"
* tag 'vfs-7.1-rc1.integrity' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs:
xfs: support T10 protection information
iomap: support T10 protection information
iomap: support ioends for buffered reads
iomap: add a bioset pointer to iomap_read_folio_ops
ntfs3: remove copy and pasted iomap code
iomap: allow file systems to hook into buffered read bio submission
iomap: only call into ->submit_read when there is a read_ctx
iomap: pass the iomap_iter to ->submit_read
iomap: refactor iomap_bio_read_folio_range
block: pass a maxlen argument to bio_iov_iter_bounce
block: add fs_bio_integrity helpers
block: make max_integrity_io_size public
block: prepare generation / verification helpers for fs usage
block: add a bdev_has_integrity_csum helper
block: factor out a bio_integrity_setup_default helper
block: factor out a bio_integrity_action helper
|
|
AMD PIIX4 SMBus adapters, present on AMD SP5/EPYC-based platforms
(including Cisco 8000 series routers), support SMBUS_BYTE_DATA and
SMBUS_WORD_DATA but lack I2C_FUNC_I2C and I2C_FUNC_SMBUS_I2C_BLOCK.
When at24 (or any driver) requests a regmap with reg_bits=16 and
val_bits=8 on such an adapter, regmap_get_i2c_bus() finds no matching
bus and returns -ENOTSUPP. The existing regmap_i2c_smbus_i2c_block_reg16
bus type already implements 16-bit addressed reads using only
write_byte_data() + read_byte() primitives, but its selection is gated
on I2C_FUNC_SMBUS_I2C_BLOCK which these adapters lack.
Add a new regmap_smbus_byte_word_reg16 bus that:
READ: reuses regmap_i2c_smbus_i2c_read_reg16() -- sets the 16-bit
address via write_byte_data(addr_lo, addr_hi), then reads
bytes sequentially via read_byte() (EEPROM auto-increments).
Requires only SMBUS_BYTE_DATA.
WRITE: uses write_word_data(addr_hi, (data << 8) | addr_lo) to
encode one data byte per SMBus WORD transaction.
Requires only SMBUS_WORD_DATA. Single-byte writes only.
The new bus is selected in regmap_get_i2c_bus() when reg_bits=16,
val_bits=8, and the adapter has SMBUS_BYTE_DATA | SMBUS_WORD_DATA but
not I2C_FUNC_I2C or SMBUS_I2C_BLOCK. The branch is placed after the
existing I2C_BLOCK_reg16 check so adapters with full block support
continue to use the faster path.
This fixes at24 EEPROM probe failures on PIIX4:
at24 3-0055: probe with driver at24 failed with error -524
No driver changes are required -- at24 already passes reg_bits=16 to
devm_regmap_init_i2c(), which now succeeds.
Signed-off-by: Nishanth Sampath Kumar <nissampa@cisco.com>
Link: https://patch.msgid.link/20260407233927.498932-1-nissampa@cisco.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
