| Age | Commit message (Collapse) | Author |
|---|
|
group->notifier is dead code. VFIO initializes it and checks it for
emptiness on teardown, but nobody ever registers on it or triggers it.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Acked-by: Anthony Krowiak <akrowiak@linux.ibm.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Link: https://lore.kernel.org/r/20260407175934.1602711-1-pbonzini@redhat.com
Signed-off-by: Alex Williamson <alex@shazbot.org>
|
|
cxl/hdm: Add support for 32 switch decoders
|
|
Factory default for this bit is "set" (at least on the chips I have),
but we must make sure it is actually set by Linux explicitly, as the
bit is writable by an earlier stage.
Fixes: 6a804fb72de5 ("mtd: spinand: winbond: add support for serial NAND flash")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
On each WMI message received from the hardware, we alloc a temporary array
of WMI_TAG_MAX entries of type void *. This array is then populated with
pointers of parsed structs depending on the WMI type, and then freed. This
alloc can fail when memory pressure in the system is high enough.
Given the fact that it is scheduled in softirq with the system_bh_wq, we
should not be able to parse more than one WMI message per CPU at any time.
So instead lets move to a per cpu allocated array, that is reused across
calls. This memory is allocated as needed and refcounted to exist only
as long as one struct ath12k_base lives.
ath12k_wmi_tlv_parse_alloc() and ath12k_wmi_tlv_parse() are merged
together as it no longer allocs mem but returns the existing per-cpu one.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00218-QCAHKSWPL_SILICONZ-1
Signed-off-by: Nicolas Escande <nico.escande@gmail.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Reviewed-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Link: https://patch.msgid.link/20260407095426.3285574-1-nico.escande@gmail.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
The krealloc() call for cap_info->phys in __efi_capsule_setup_info() uses
sizeof(phys_addr_t *) instead of sizeof(phys_addr_t), which might be
causing an undersized allocation.
The allocation is also inconsistent with the initial array allocation in
efi_capsule_open() that allocates one entry with sizeof(phys_addr_t),
and the efi_capsule_write() function that stores phys_addr_t values (not
pointers) via page_to_phys().
On 64-bit systems where sizeof(phys_addr_t) == sizeof(phys_addr_t *), this
goes unnoticed. On 32-bit systems with PAE where phys_addr_t is 64-bit but
pointers are 32-bit, this allocates half the required space, which might
lead to a heap buffer overflow when storing physical addresses.
This is similar to the bug fixed in commit fccfa646ef36 ("efi/capsule-loader:
fix incorrect allocation size") which fixed the same issue at the initial
allocation site.
Fixes: f24c4d478013 ("efi/capsule-loader: Reinstate virtual capsule mapping")
Assisted-by: Claude:claude-sonnet-4-5
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs
Pull vfs fixes from Christian Brauner:
"The kernfs rbtree is keyed by (hash, ns, name) where the hash
is seeded with the raw namespace pointer via init_name_hash(ns).
The resulting hash values are exposed to userspace through
readdir seek positions, and the pointer-based ordering in
kernfs_name_compare() is observable through entry order.
Switch from raw pointers to ns_common::ns_id for both hashing
and comparison.
A preparatory commit first replaces all const void * namespace
parameters with const struct ns_common * throughout kernfs, sysfs,
and kobject so the code can access ns->ns_id. Also compare the
ns_id when hashes match in the rbtree to handle crafted collisions.
Also fix eventpoll RCU grace period issue and a cachefiles refcount
problem"
* tag 'vfs-7.0-rc8.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs:
kernfs: make directory seek namespace-aware
kernfs: use namespace id instead of pointer for hashing and comparison
kernfs: pass struct ns_common instead of const void * for namespace tags
eventpoll: defer struct eventpoll free to RCU grace period
cachefiles: fix incorrect dentry refcount in cachefiles_cull()
|
|
Depending on the architecture the transfer buffer may share a cacheline
with the following mutex. As the buffer may be used for DMA, that is
problematic.
Use the high-level DMA helpers to make sure that cacheline sharing can
not happen.
Also drop the comment, as the helpers are documentation enough.
https://sashiko.dev/#/message/20260408175814.934BFC19421%40smtp.kernel.org
Fixes: 4381a36abdf1c ("hwmon: add POWER-Z driver")
Cc: stable@vger.kernel.org # ca085faabb42: dma-mapping: add __dma_from_device_group_begin()/end()
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20260408-powerz-cacheline-alias-v1-1-1254891be0dd@weissschuh.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio fixes from Bartosz Golaszewski:
- gracefully handle missing regmap in gpio-bd72720
- fix IRQ resource release in gpio-tegra
- return -ENOMEM on devm_kzalloc() failure instead of -ENODEV in
gpio-tegra
* tag 'gpio-fixes-for-v7.0' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
gpio: tegra: return -ENOMEM on allocation failure in probe
gpio: tegra: fix irq_release_resources calling enable instead of disable
gpio: bd72720: handle missing regmap
|
|
Per CXL r4.0 section 8.2.4.20.1. CXL host bridge and switch ports can
support 32 HDM decoders. Current implementation misses some decoders on
CXL host bridge and switch in the case that the value of Decoder Count
field in CXL HDM decoder Capability Register is greater than or equal to
9.
Update calculation implementation to ensure the decoder count calculation
is correct for CXL host bridge/switch ports.
Signed-off-by: Li Ming <ming.li@zohomail.com>
Reviewed-by: Gregory Price <gourry@gourry.net>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Alison Schofield <alison.schofield@intel.com>
Link: https://patch.msgid.link/20260321061459.1910205-1-ming.li@zohomail.com
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
|
|
isl28022_read_power() computes:
*val = ((51200000L * ((long)data->gain)) /
(long)data->shunt) * (long)regval;
On 32-bit platforms, 'long' is 32 bits. With gain=8 and shunt=10000
(the default configuration):
(51200000 * 8) / 10000 = 40960
40960 * 65535 = 2,684,313,600
This exceeds LONG_MAX (2,147,483,647), resulting in signed integer
overflow.
Additionally, dividing before multiplying by regval loses precision
unnecessarily.
Use u64 arithmetic with div_u64() and multiply before dividing to
retain precision. The intermediate product cannot overflow u64
(worst case: 51200000 * 8 * 65535 = 26843136000000). Power is
inherently non-negative, so unsigned types are the natural fit.
Cap the result to LONG_MAX before returning it through the hwmon
callback.
Fixes: 39671a14df4f2 ("hwmon: (isl28022) new driver for ISL28022 power monitor")
Cc: stable@vger.kernel.org
Signed-off-by: Sanman Pradhan <psanman@juniper.net>
Link: https://lore.kernel.org/r/20260410002613.424557-1-sanman.pradhan@hpe.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Fix two bugs in pt5161l_read_block_data():
1. Buffer overrun: The local buffer rbuf is declared as u8 rbuf[24],
but i2c_smbus_read_block_data() can return up to
I2C_SMBUS_BLOCK_MAX (32) bytes. The i2c-core copies the data into
the caller's buffer before the return value can be checked, so
the post-read length validation does not prevent a stack overrun
if a device returns more than 24 bytes. Resize the buffer to
I2C_SMBUS_BLOCK_MAX.
2. Unexpected positive return on length mismatch: When all three
retries are exhausted because the device returns data with an
unexpected length, i2c_smbus_read_block_data() returns a positive
byte count. The function returns this directly, and callers treat
any non-negative return as success, processing stale or incomplete
buffer contents. Return -EIO when retries are exhausted with a
positive return value, preserving the negative error code on I2C
failure.
Fixes: 1b2ca93cd0592 ("hwmon: Add driver for Astera Labs PT5161L retimer")
Cc: stable@vger.kernel.org
Signed-off-by: Sanman Pradhan <psanman@juniper.net>
Link: https://lore.kernel.org/r/20260410002549.424162-1-sanman.pradhan@hpe.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
wait_for_completion_interruptible_timeout() returns -ERESTARTSYS when
interrupted. This needs to abort the URB and return an error. No data
has been received from the device so any reads from the transfer
buffer are invalid.
The original code tests !ret, which only catches the timeout case (0).
On signal delivery (-ERESTARTSYS), !ret is false so the function skips
usb_kill_urb() and falls through to read from the unfilled transfer
buffer.
Fix by capturing the return value into a long (matching the function
return type) and handling signal (negative) and timeout (zero) cases
with separate checks that both call usb_kill_urb() before returning.
Fixes: 4381a36abdf1c ("hwmon: add POWER-Z driver")
Cc: stable@vger.kernel.org
Signed-off-by: Sanman Pradhan <psanman@juniper.net>
Link: https://lore.kernel.org/r/20260410002521.422645-3-sanman.pradhan@hpe.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
After powerz_disconnect() frees the URB and releases the mutex, a
subsequent powerz_read() call can acquire the mutex and call
powerz_read_data(), which dereferences the freed URB pointer.
Fix by:
- Setting priv->urb to NULL in powerz_disconnect() so that
powerz_read_data() can detect the disconnected state.
- Adding a !priv->urb check at the start of powerz_read_data()
to return -ENODEV on a disconnected device.
- Moving usb_set_intfdata() before hwmon registration so the
disconnect handler can always find the priv pointer.
Fixes: 4381a36abdf1c ("hwmon: add POWER-Z driver")
Cc: stable@vger.kernel.org
Signed-off-by: Sanman Pradhan <psanman@juniper.net>
Link: https://lore.kernel.org/r/20260410002521.422645-2-sanman.pradhan@hpe.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"Some late pin control fixes. I'm not happy to have bugs so late in the
kernel cycle, but they are all driver specifics so I guess it's how it
is.
- Three fixes for the Intel pin control driver fixing the feature set
for the new silicon
- One fix for an IRQ storm in the MCP23S08 pin controller/GPIO
expander"
* tag 'pinctrl-v7.0-4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: mcp23s08: Disable all pin interrupts during probe
pinctrl: intel: Enable 3-bit PAD_OWN feature
pinctrl: intel: Fix the revision for new features (1kOhm PD, HW debouncer)
pinctrl: intel: Improve capability support
|
|
Add pmbus support for Sony APS-379 power supplies. There are a few PMBUS
commands that return data that is undocumented/invalid so these need to
be rejected with -ENXIO. The READ_VOUT command returns data in linear11
format instead of linear16 so we need to workaround this.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20260410012414.2818829-3-chris.packham@alliedtelesis.co.nz
[groeck: Dropped empty line from documentation; added module name to Kconfig]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
commit b6a57912854e ("HID: logitech-dj: Prevent REPORT_ID_DJ_SHORT
related user initiated OOB write") assumed that all HID devices attached
to the logitech-dj driver was having an output report of DJ_SHORT.
However, on the receiver itself, we have 2 other HID device we attach
here: the mouse emulation and the keyboard emulation. For those devices
the value of rep is NULL and we are triggered a segfault here.
This is doubly required because logitech-dj also handles non DJ devices
that might not have the DJ collection.
Fixes: b6a57912854e ("HID: logitech-dj: Prevent REPORT_ID_DJ_SHORT related user initiated OOB write")
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
|
|
Much like commit 19f953e74356 ("fbdev: fb_pm2fb: Avoid potential divide
by zero error"), we also need to prevent that same crash from happening
in the udlfb driver as it uses pixclock directly when dividing, which
will crash.
Cc: Bernie Thompson <bernie@plugable.com>
Cc: Helge Deller <deller@gmx.de>
Fixes: 59277b679f8b ("Staging: udlfb: add dynamic modeset support")
Assisted-by: gregkh_clanker_t1000
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
Much like commit 19f953e74356 ("fbdev: fb_pm2fb: Avoid potential divide
by zero error"), we also need to prevent that same crash from happening
in the udlfb driver as it uses pixclock directly when dividing, which
will crash.
Cc: Helge Deller <deller@gmx.de>
Assisted-by: gregkh_clanker_t1000
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
The WCN39xx family of WiFi/BT chips incorporates a simple PMU, spreading
voltages over internal rails. Implement support for using powersequencer
for this family of QCA devices in addition to using regulators.
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Use proper alignment for break under a switch.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
sudo lspci -v -k -d 8086:6e74
80:14.7 Bluetooth: Intel Corporation Device 6e74 (rev 10)
Subsystem: Intel Corporation Device 0011
Flags: bus master, fast devsel, latency 0, IRQ 16
Memory at 200002a8000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [c8] Power Management version 3
Capabilities: [d0] MSI: Enable- Count=1/1 Maskable- 64bit+
Capabilities: [40] Express Root Complex Integrated Endpoint, MSI 00
Capabilities: [80] MSI-X: Enable+ Count=32 Masked-
Capabilities: [100] Latency Tolerance Reporting
Kernel driver in use: btintel_pcie
Kernel modules: btintel_pcie
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
sudo lspci -v -k -d 8086:d346
00:14.7 Bluetooth: Intel Corporation Device d346
Subsystem: Intel Corporation Device 0011
Flags: bus master, fast devsel, latency 0, IRQ 16, IOMMU group 14
Memory at b018378000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [c8] Power Management version 3
Capabilities: [d0] MSI: Enable- Count=1/1 Maskable- 64bit+
Capabilities: [40] Express Root Complex Integrated Endpoint, MSI 00
Capabilities: [80] MSI-X: Enable+ Count=32 Masked-
Capabilities: [100] Latency Tolerance Reporting
Kernel driver in use: btintel_pcie
Kernel modules: btintel_pcie
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add device coredump support for Scorpious Peak2F product.
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add support for Intel Bluetooth Scorpious Peak2F core.
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add device coredump support for Scorpious Peak2 product.
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add DSBR support for Scorpious Peak2 cores onwards.
Refer commit eb9e749c0182 ("Bluetooth: btintel: Allow configuring drive
strength of BRI") for details about DSBR.
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add support for Intel Bluetooth Scorpious Peak2 core.
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Use hardware variant instead of CNVi to send dsbr command.
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
If FW image has hybrid signature (ECDSA and LMS) then send CSS header,
ECDSA public key, ECDSA signature, LMS public key, LMS signature and
command buffer to device.
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add MT7902 Bluetooth SDIO support by introducing chip data and
registering the device ID.
Runtime PM is not yet supported by the driver, but normal operation
is unaffected.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add VID 0e8d & PID 1ede for MediaTek MT7902 USB Bluetooth chip.
The information in /sys/kernel/debug/usb/devices about the Bluetooth
device is listed as the below.
T: Bus=01 Lev=01 Prnt=01 Port=05 Cnt=02 Dev#= 4 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0e8d ProdID=1ede Rev= 1.00
S: Manufacturer=MediaTek Inc.
S: Product=Wireless_Device
S: SerialNumber=000000000
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA
A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms
I: If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us
I:* If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us
Co-developed-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add VID 13d3 & PID 3596 for MediaTek MT7902 USB Bluetooth chip.
The information in /sys/kernel/debug/usb/devices about the Bluetooth
device is listed as the below.
T: Bus=07 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=13d3 ProdID=3596 Rev= 1.00
S: Manufacturer=MediaTek Inc.
S: Product=Wireless_Device
S: SerialNumber=000000000
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA
A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us
I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us
Co-developed-by: Kush Kulshrestha <kush.kulshrestha.5@gmail.com>
Signed-off-by: Kush Kulshrestha <kush.kulshrestha.5@gmail.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add VID 13d3 & PID 3594 for MediaTek MT7902 USB Bluetooth chip.
The information in /sys/kernel/debug/usb/devices about the Bluetooth
device is listed as the below.
T: Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 3 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=13d3 ProdID=3594 Rev= 1.00
S: Manufacturer=MediaTek Inc.
S: Product=Wireless_Device
S: SerialNumber=000000000
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA
A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us
I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us
Co-developed-by: Kush Kulshrestha <kush.kulshrestha.5@gmail.com>
Signed-off-by: Kush Kulshrestha <kush.kulshrestha.5@gmail.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add VID 13d3 & PID 3580 for MediaTek MT7902 USB Bluetooth chip.
The information in /sys/kernel/debug/usb/devices about the Bluetooth
device is listed as the below.
T: Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=13d3 ProdID=3580 Rev= 1.00
S: Manufacturer=MediaTek Inc.
S: Product=Wireless_Device
S: SerialNumber=000000000
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA
A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms
I: If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us
I:* If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us
Co-developed-by: Kush Kulshrestha <kush.kulshrestha.5@gmail.com>
Signed-off-by: Kush Kulshrestha <kush.kulshrestha.5@gmail.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add VID 13d3 & PID 3579 for MediaTek MT7902 USB Bluetooth chip.
The information in /sys/kernel/debug/usb/devices about the Bluetooth
device is listed as the below.
T: Bus=01 Lev=01 Prnt=01 Port=09 Cnt=04 Dev#= 7 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=13d3 ProdID=3579 Rev= 1.00
S: Manufacturer=MediaTek Inc.
S: Product=Wireless_Device
S: SerialNumber=000000000
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA
A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms
I: If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us
I:* If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add MT7902 device ID and firmware filename to enable MCU firmware
loading.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Use struct_size(), which provides additional compile-time checks for
structures with flexible array members (e.g., __must_be_array()), to
determine the allocation size for a new 'struct hci_drv_rp_read_info'.
Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add USB device ID (04ca:3807) for a Lite-On Wireless_Device containing
a MediaTek MT7921 (MT7920) Bluetooth chipset found in Acer laptops.
Without this entry, btusb binds via the generic USB class-based wildcard
match but never sets the BTUSB_MEDIATEK flag. This means btmtk never
triggers firmware loading, and the driver sends a raw HCI Reset that
the uninitialized chip cannot respond to, resulting in:
Bluetooth: hci0: Opcode 0x0c03 failed: -110
The information in /sys/kernel/debug/usb/devices about the Bluetooth
device is listed as the below:
T: Bus=03 Lev=01 Prnt=01 Port=09 Cnt=01 Dev#=5 Spd=480 MxCh=0
P: Vendor=04ca ProdID=3807 Rev=1.00
S: Manufacturer=MediaTek Inc.
S: Product=Wireless_Device
S: SerialNumber=000000000
C: #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I: If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Dylan Eray <dylan.eray6@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Replace snprintf("%s", ...) with the faster and more direct strscpy().
Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
The BT core skips calling the hci_dev's shutdown method when the HCI
is unregistered. This means that qca_power_off() was not getting called
leaving BT powered on.
This causes regulators / pwrseq providers to not get disabled which also
causes problem when re-loading the module because regulators and pwrseq
providers have an enablecount which now has never dropped to 0, causing
the BT to not get properly reset between rmmod and re-load which causes
initialization failure on the re-load.
Fix this by calling qca_power_off() from qca_close() when BT has not
already been powered off through a qca_hci_shutdown() call.
hci_ldisc.c will call qca_close() after freeing the hdev, so this
means that qca_power_off() can now no longer deref hu->hdev, change
the logging in qca_power_off() to no longer use hu->hdev.
Signed-off-by: Hans de Goede <johannes.goede@oss.qualcomm.com>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
The function called qca_power_off() is actually the hci_dev shutdown
handler, rename it to qca_hci_shutdown() to make this clear.
While the qca_power_shutdown() function is actually the counter-part
of qca_power_on() rename it to qca_power_off() to make this clear.
Signed-off-by: Hans de Goede <johannes.goede@oss.qualcomm.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This patch adds the device ID for the BCM4343A2 module, found e.g.
in the muRata 1YN WiFi+BT combined device. The required firmware
file is named 'BCM4343A2.hcd'.
Signed-off-by: Marek Vasut <marex@nabladev.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Whenever new chipset support is added to the driver code,
we ended up adding chipset name to the last of the switch case
arising code readability issue because of improper sorting of
the chipset names in various places of the code.
Refactor code such a way that new chipset can be added easily
in the code without compromising code readability.
Signed-off-by: Vivek Sahu <vivek.sahu@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add a new flag 'BTMTK_FIRMWARE_DL_RETRY'.
If an error occurs during mt79xx firmware download process, this flag
will be set and cleared after a reset. If the flag is already set and
firmware still cannot be loaded successfully after a reset, no further
reset attempts will be made. In other words, if there is a problem during
firmware download, only one reset will be attempted.
Signed-off-by: Chris Lu <chris.lu@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
To prevent abnormal controller states, it is necessary to check
status in another part of the mt79xx firmware setup. During this
process, receiving the 'BTMTK_WMT_PATCH_PROGRESS' status is unexpected.
If this occurs, it should be treated as an error, and driver must be
prevented from continuing execution.
Signed-off-by: Chris Lu <chris.lu@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
removal
CXL is linked before fwctl in drivers/Makefile. Both use `module_init, so
`cxl_pci_driver_init()` runs first. When `cxl_pci_probe()` calls
`fwctl_register()` and then `device_add()`, fwctl_class is not yet
registered because fwctl_init() hasn't run, causing `class_to_subsys()` to
return NULL and skip knode_class initialization.
On device removal, `class_to_subsys()` returns non-NULL, and
`device_del()` calls `klist_del()` on the uninitialized knode, triggering
a NULL pointer dereference.
Fixes: 858ce2f56b52 ("cxl: Add FWCTL support to CXL")
Link: https://patch.msgid.link/r/20260409051902.40218-1-icheng@nvidia.com
Signed-off-by: Richard Cheng <icheng@nvidia.com>
Reviewed-by: Kai-Heng Feng <kaihengf@nvidia.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
|
|
If retries are exhausted, driver should not do futher operation.
During mt79xx firmware download process, if the retry count reaches0,
driver will return an -EIO error and release the firmware resources.
Signed-off-by: Chris Lu <chris.lu@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
There is no point in having the label since all it does is return the
value in the 'err' variable. Instead make every goto return directly
and remove the label.
Signed-off-by: Dongyang Jin <jindongyang@kylinos.cn>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add VID 0489 & PID e174 for MediaTek MT7922 USB Bluetooth chip.
The information in /sys/kernel/debug/usb/devices about the Bluetooth
device is listed as the below.
T: Bus=06 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0489 ProdID=e174 Rev= 1.00
S: Manufacturer=MediaTek Inc.
S: Product=Wireless_Device
S: SerialNumber=000000000
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA
A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms
I: If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us
I:* If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us
Signed-off-by: Chris Lu <chris.lu@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add a con_id parameter to skl_int3472_register_led() to allow callers
to specify both the LED name suffix and lookup con_id instead of
hardcoding "privacy". This prepares for registering additional LED
types with different names.
While at it, rename the privacy LED's GPIO con_id from "privacy-led"
to "privacy" in int3472_get_con_id_and_polarity() and pass it
directly to skl_int3472_register_led(), reducing churn when adding
new LED types.
No functional change.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Hans de Goede <johannes.goede@oss.qualcomm.com>
Signed-off-by: Marco Nenciarini <mnencia@kcore.it>
Link: https://patch.msgid.link/20260401203638.1601661-4-mnencia@kcore.it
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
