| Age | Commit message (Collapse) | Author |
|---|
|
UGREEN USB-C Multifunction Adapter Model CM512 (AKA "Revodok 107")
exposes two SVIDs: 0xff01 (DP Alt Mode) and 0x1d5c. The DISCOVER_MODES
step succeeds for 0xff01 and gets a NAK for 0x1d5c. Currently this
results in DP Alt Mode not being registered either, since the modes
are only registered once all of them have been discovered. The NAK
results in the processing being stopped and thus no Alt modes being
registered.
Improve the situation by handling the NAK gracefully and continue
processing the other modes.
Before this change, the TCPM log ends like this:
(more log entries before this)
[ 5.028287] AMS DISCOVER_SVIDS finished
[ 5.028291] cc:=4
[ 5.040040] SVID 1: 0xff01
[ 5.040054] SVID 2: 0x1d5c
[ 5.040082] AMS DISCOVER_MODES start
[ 5.040096] PD TX, header: 0x1b6f
[ 5.050946] PD TX complete, status: 0
[ 5.059609] PD RX, header: 0x264f [1]
[ 5.059626] Rx VDM cmd 0xff018043 type 1 cmd 3 len 2
[ 5.059640] AMS DISCOVER_MODES finished
[ 5.059644] cc:=4
[ 5.069994] Alternate mode 0: SVID 0xff01, VDO 1: 0x000c0045
[ 5.070029] AMS DISCOVER_MODES start
[ 5.070043] PD TX, header: 0x1d6f
[ 5.081139] PD TX complete, status: 0
[ 5.087498] PD RX, header: 0x184f [1]
[ 5.087515] Rx VDM cmd 0x1d5c8083 type 2 cmd 3 len 1
[ 5.087529] AMS DISCOVER_MODES finished
[ 5.087534] cc:=4
(no further log entries after this point)
After this patch the TCPM log looks exactly the same, but then
continues like this:
[ 5.100222] Skip SVID 0x1d5c (failed to discover mode)
[ 5.101699] AMS DFP_TO_UFP_ENTER_MODE start
(log goes on as the system initializes DP AltMode)
Cc: stable <stable@kernel.org>
Fixes: 41d9d75344d9 ("usb: typec: tcpm: add discover svids and discover modes support for sop'")
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: RD Babiera <rdbabiera@google.com>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://patch.msgid.link/20260429-tcpm-discover-modes-nak-fix-v4-1-75945d0ed30f@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
According to the cdns3 datasheet, the EPRST (Endpoint Reset) command
causes the DMA engine to reposition its internal pointer to the next
Transfer Descriptor (TD) if it was already processing one.
This issue is consistently observed during the ADB identification
process on macOS hosts, where the host issues a Clear_Halt. Although
commit 4bf2dd65135a ("usb: cdns3: gadget: toggle cycle bit before reset
endpoint") attempted to avoid DMA advance by toggling the cycle bit,
trace logs show that on certain hosts like macOS, the DMA pointer
(EP_TRADDR) still shifts after EPRST:
cdns3_ctrl_req: Clear Endpoint Feature(Halt ep1out)
cdns3_doorbell_epx: ep1out, ep_trbaddr f9c04030 <-- Should be f9c04000
cdns3_gadget_giveback: ep1out: req: ... length: 16384/16384
As shown above, the DMA pointer jumped to the next TD, causing
the controller to skip the initial TRBs of the request. This leads to
data misalignment and ADB protocol hangs on macOS.
Fix this by manually restoring the EP_TRADDR register to the starting
physical address of the current request after the EPRST operation is
complete.
Fixes: 7733f6c32e36 ("usb: cdns3: Add Cadence USB3 DRD Driver")
Cc: stable <stable@kernel.org>
Cc: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Yongchao Wu <yongchao.wu@autochips.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://patch.msgid.link/20260513160012.2547894-1-yongchao.wu@autochips.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
the runtime PM usage counter across bind/unbind cycles
Call pm_runtime_allow(dev) conditionally at cdns3_plat_remove.
Fixes: f738957277ba ("usb: cdns3: Split core.c into cdns3-plat and core.c file")
Cc: stable <stable@kernel.org>
Reported-by: sashiko-bot <sashiko-bot@kernel.org>
Closes: https://lore.kernel.org/linux-devicetree/agKaEePSFknhDBg2@nchen-desktop/T/#m21e1d9c1574eb127ce03c0c2a1a49002ce435b52
Signed-off-by: Peter Chen <peter.chen@cixtech.com>
Link: https://patch.msgid.link/20260513085310.2217547-3-peter.chen@cixtech.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
failure
Move usb2_phy initialization after usb3_phy acquisition.
Fixes: f738957277ba ("usb: cdns3: Split core.c into cdns3-plat and core.c file")
Cc: stable <stable@kernel.org>
Reported-by: sashiko-bot <sashiko-bot@kernel.org>
Closes: https://lore.kernel.org/linux-devicetree/agKaEePSFknhDBg2@nchen-desktop/T/#m21e1d9c1574eb127ce03c0c2a1a49002ce435b52
Signed-off-by: Peter Chen <peter.chen@cixtech.com>
Link: https://patch.msgid.link/20260513085310.2217547-2-peter.chen@cixtech.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
While being less compact, using named initializers allows to more easily
see which members of the structs are assigned which value without having
to lookup the declaration of the struct. And it's also more robust
against changes to the struct definition.
This patch doesn't modify the compiled array, only its representation in
source form benefits. The former was confirmed with x86 and arm64
builds.
Signed-off-by: Uwe Kleine-König (The Capable Hub) <u.kleine-koenig@baylibre.com>
Reviewed-by: Vladimir Zapolskiy <vz@kernel.org>
Link: https://patch.msgid.link/20260519161300.1598095-2-u.kleine-koenig@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
While being less compact, using named initializers allows to more easily
see which members of the structs are assigned which value without having
to lookup the declaration of the struct. And it's also more robust
against changes to the struct definition.
While touching all these arrays, unify usage of whitespace in the list
terminator.
This patch doesn't modify the compiled arrays, only their representation
in source form benefits. The former was confirmed with x86 and arm64
builds.
Signed-off-by: Uwe Kleine-König (The Capable Hub) <u.kleine-koenig@baylibre.com>
Reviewed-by: Richard Leitner <richard.leitner@linux.dev>
Link: https://patch.msgid.link/20260518135536.781168-2-u.kleine-koenig@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
While being less compact, using named initializers allows to more easily
see which members of the structs are assigned which value without having
to lookup the declaration of the struct. And it's also more robust
against changes to the struct definition.
The mentioned robustness is relevant for a planned change to struct
i2c_device_id that replaces .driver_data by an anonymous union.
While touching all these arrays, unify usage of whitespace in the list
terminator.
This patch doesn't modify the compiled arrays, only their representation
in source form benefits. The former was confirmed with x86 and arm64
builds.
Signed-off-by: Uwe Kleine-König (The Capable Hub) <u.kleine-koenig@baylibre.com>
Link: https://patch.msgid.link/20260518110142.637215-2-u.kleine-koenig@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The SIGMACHIP USB mouse with VID/PID 1c4f:0034 can disconnect and
re-enumerate repeatedly after it has been enumerated if its interrupt
endpoint is not continuously polled.
This was observed with the device reporting itself as "SIGMACHIP Usb
Mouse". Keeping the input event device open avoids the disconnects.
Add HID_QUIRK_ALWAYS_POLL for this device so the HID core keeps polling
it even when there is no userspace input consumer.
Cc: stable@vger.kernel.org
Signed-off-by: hlleng <a909204013@gmail.com>
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
|
|
We're leaking the initial DMA mapping during iteration if we fail to
allocate the tracking descriptor for both PRP and SGL. Unmap the
iterator directly; we can't use the existing unmap helper because it
depends on the tracking descriptor being successfully allocated, so a
new one for an in-use iterator is provided.
The mappings were also leaking when the driver detects an invalid
bio_vec when mapping PRPs, so fix that too.
Fixes: b8b7570a7ec87 ("nvme-pci: fix dma unmapping when using PRPs and not using the IOVA mapping")
Fixes: 7ce3c1dd78fca ("nvme-pci: convert the data mapping to blk_rq_dma_map")
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
|
We don't unmap P2P memory, so we don't need to track it. The dma_vec
allocation was getting leaked on the completion.
Fixes: b8b7570a7ec87 ("nvme-pci: fix dma unmapping when using PRPs and not using the IOVA mapping")
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
|
Add an auxiliary-bus hwmon driver for the temperature sensor exposed by
AMD Promontory 21 (PROM21) xHCI PCI functions. The driver binds to the
"hwmon" auxiliary device published by the PROM21 xHCI PCI glue and
exposes the sensor as temp1_input under the prom21_xhci hwmon device.
The sensor is accessed through a PROM21 vendor index/data register pair
in the xHCI PCI MMIO BAR. The driver consumes parent-provided MMIO data
from the PROM21 PCI glue instead of inspecting the parent PCI driver's
drvdata. The read path restores the previous vendor index value after
sampling and does not runtime-resume the parent PCI device; reads from a
suspended parent return -ENODATA.
Document the supported device, register access, runtime PM behavior, and
sysfs lookup method. The documentation also records the observation
method used to identify the register pair and derive the conversion
formula.
Assisted-by: Codex:gpt-5.5
Signed-off-by: Jihong Min <hurryman2212@gmail.com>
Reviewed-by: Mario Limonciello (AMD) <superm1@kernel.org>
Tested-by: Yaroslav Isakov <yaroslav.isakov@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://patch.msgid.link/20260519000732.2334711-3-hurryman2212@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
AMD Promontory 21 (PROM21) xHCI PCI functions use the common xhci-pci
core for USB operation, but also expose controller-specific sensor data.
Add a small PROM21 PCI glue driver for AMD 1022:43fc and 1022:43fd
controllers.
The glue delegates USB host operation to the common xhci-pci core and
publishes a "hwmon" auxiliary device with parent-provided MMIO data.
Auxiliary device creation failure is logged but does not fail the xHCI
probe.
Make the PROM21 glue a hidden Kconfig tristate driven by the user-visible
SENSORS_PROM21_XHCI option. If sensor support is disabled, generic
xhci-pci binds PROM21 controllers normally. If sensor support is enabled,
the glue follows USB_XHCI_PCI.
This keeps the auxiliary device available for a modular sensor driver while
avoiding a built-in xhci-pci core handing PROM21 controllers to a glue
driver that is only available as a module during initramfs.
Assisted-by: Codex:gpt-5.5
Signed-off-by: Jihong Min <hurryman2212@gmail.com>
Reviewed-by: Mario Limonciello (AMD) <superm1@kernel.org>
Tested-by: Yaroslav Isakov <yaroslav.isakov@gmail.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Link: https://patch.msgid.link/20260519000732.2334711-2-hurryman2212@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove the driver-internal function entry/exit debug messages
in favor of existing kernel-level function tracing mechanisms.
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/all/2026051657-scruffy-embark-45ea@gregkh/
Signed-off-by: Mauricio Faria de Oliveira <mfo@igalia.com>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Link: https://patch.msgid.link/20260520-ueagle-atm-cleanup-v1-2-010c8bc7b214@igalia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Convert dev_info() to dev_dbg().
Per 'Documentation/process/coding-style.rst':
13) Printing kernel messages
... When drivers are working properly they are quiet,
so prefer to use dev_dbg/pr_debug unless something is wrong.
While in there, correct the verb form and add 'with' for clarity.
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/all/2026051628-squatter-stature-c0e0@gregkh/
Signed-off-by: Mauricio Faria de Oliveira <mfo@igalia.com>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Link: https://patch.msgid.link/20260520-ueagle-atm-cleanup-v1-1-010c8bc7b214@igalia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use FIELD_MODIFY() to remove open-coded bit manipulation.
No functional change intended.
Signed-off-by: Hans Zhang <18255117159@163.com>
Link: https://patch.msgid.link/20260430163919.47372-7-18255117159@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use FIELD_MODIFY() to remove open-coded bit manipulation.
No functional change intended.
Signed-off-by: Hans Zhang <18255117159@163.com>
Link: https://patch.msgid.link/20260430163919.47372-6-18255117159@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use FIELD_MODIFY() to remove open-coded bit manipulation.
No functional change intended.
Signed-off-by: Hans Zhang <18255117159@163.com>
Link: https://patch.msgid.link/20260430163919.47372-5-18255117159@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use FIELD_MODIFY() to remove open-coded bit manipulation.
No functional change intended.
Signed-off-by: Hans Zhang <18255117159@163.com>
Link: https://patch.msgid.link/20260430163919.47372-4-18255117159@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use FIELD_MODIFY() to remove open-coded bit manipulation.
No functional change intended.
Signed-off-by: Hans Zhang <18255117159@163.com>
Link: https://patch.msgid.link/20260430163919.47372-3-18255117159@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use FIELD_MODIFY() to remove open-coded bit manipulation.
No functional change intended.
Signed-off-by: Hans Zhang <18255117159@163.com>
Link: https://patch.msgid.link/20260430163919.47372-2-18255117159@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The kernel-doc comment for dwc3_alloc_event_buffers states that the
function "Allocates @num event buffers", but the function does not have
a @num parameter and only allocates a single event buffer.
Remove the misleading "@num" reference from the brief description to
accurately reflect the function's behavior.
Signed-off-by: Shuping Bu <bushuping007@163.com>
Link: https://patch.msgid.link/20260520055023.2415635-1-bushuping007@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
pcc_cpufreq_do_osc() calls acpi_evaluate_object() twice for the
two-phase _OSC negotiation. Between the two calls it freed
output.pointer but left output.length unchanged. Since
acpi_evaluate_object() treats a non-zero length with a non-NULL
pointer as an existing buffer to write into, the second call wrote
into freed memory (use-after-free). The subsequent kfree(output.pointer)
at out_free then freed the same pointer a second time (double free).
Reset output.pointer to NULL and output.length to ACPI_ALLOCATE_BUFFER
after freeing the first result, so ACPICA allocates a fresh buffer for
each phase independently.
Fixes: 0f1d683fb35d ("[CPUFREQ] Processor Clocking Control interface driver")
Signed-off-by: Yuho Choi <dbgh9129@gmail.com>
Reviewed-by: Zhongqiu Han <zhongqiu.han@oss.qualcomm.com>
Cc: All applicable <stable@vger.kernel.org>
Link: https://patch.msgid.link/20260416144621.93964-1-dbgh9129@gmail.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
If devm_drm_dp_hpd_bridge_add() fails during fusb302_probe(), the original
code returned directly without cleaning up the resources.
Move bridge registration before the IRQ is requested and route bridge
registration failures through the existing TCPM unregister and fwnode
cleanup path.
Fixes: 5d79c525405d ("usb: typec: fusb302: add DRM DP HPD bridge support")
Signed-off-by: Felix Gu <ustc.gu@gmail.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://patch.msgid.link/20260428-fusb-v2-1-aa3b5942cabb@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix error handling and resource cleanup i.e remove invalid
phy_exit() after failed phy_init(), route failures through
proper cleanup paths and return 0 explicitly on success.
Fixes: 84770f028fab ("usb: dwc3: Add driver for Xilinx platforms")
Cc: stable@vger.kernel.org
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Link: https://patch.msgid.link/20260519115529.2980421-1-radhey.shyam.pandey@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
ipmi_alloc_recv_msg(user) takes the temporary user reference owned by the
receive message, and ipmi_free_recv_msg() drops it again. If event delivery
fails after allocating receive messages for earlier users,
handle_read_event_rsp() rolls those messages back with
ipmi_free_recv_msg().
That rollback path still drops user->refcount explicitly after freeing each
message. The extra put can free a user that remains linked on intf->users,
so later event delivery may dereference a freed user or trip refcount_t's
addition-on-zero warning when ipmi_alloc_recv_msg() tries to acquire
another reference.
Remove the stale explicit put and the now-dead user assignment. Keep the
list_del() and ipmi_free_recv_msg() calls; they are the required rollback
operations.
Fixes: b52da4054ee0 ("ipmi: Rework user message limit handling")
Cc: stable@vger.kernel.org # v6.18+
Signed-off-by: Matt Fleming <mfleming@cloudflare.com>
Message-ID: <20260521130628.3641050-1-matt@readmodwrite.com>
Signed-off-by: Corey Minyard <corey@minyard.net>
|
|
Richard Fitzgerald <rf@opensource.cirrus.com> says:
This series fixes bugs and a typo in cs-amp-lib.
Link: https://patch.msgid.link/20260521122511.987322-1-rf@opensource.cirrus.com
|
|
The only caller of exynos_drm_framebuffer_init() is the helper
exynos_user_fb_create() from the same source file. Declare the
former as static. Tidy up the header's include statements.
v2:
- clean up the includes in the header file (Chen-Yu)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
Replace the internal DRM framebuffer with a DRM client buffer. The
client buffer allocates the DRM framebuffer on a file and also uses
GEM object handles via the regular ADDFB2 interfaces.
Using client-buffer interfaces unifies framebuffer allocation for
DRM clients in user space and exynos' internal fbdev emulation. It
also simplifies the clean-up side of the fbdev emulation.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
Replace the geometry and size calculation in exynos' fbdev emulation
with DRM format helpers. This consists of a 4CC lookup from the fbdev
parameters, format lookup, pitch calculation and size calculation.
Then allocate the GEM buffer object for the framebuffer memory from
the calculated size. Mmap provides the allocated buffer to user space,
so align the buffer size to PAGE_SIZE.
Initialize the fields screen_size and fix.smem_len in struct fb_info
from the size of the allocated buffer object. This is the real size
and can differ from the requested size.
v3:
- add more error checks to geometry calculations
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
Inline exynos_drm_fbdev_update() into its only caller. Prepares the
code for using DRM client buffers.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
The screen_buffer field in struct fb_info contains the kernel address
of the first byte of framebuffer memory. Do not add the display offset.
This offset only describes scrolling during scanout.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Fixes: 19c8b8343d9c ("drm/exynos: fixed overlay data updating.")
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: <stable@vger.kernel.org> # v3.2+
|
|
adm1266_state_read() backs the sequencer_state debugfs entry and
issues an i2c_smbus_read_word_data(client, ADM1266_READ_STATE)
against the device without taking pmbus_lock. pmbus_core holds
pmbus_lock around its own multi-transaction sequences (notably the
"set PAGE, then read paged register" pattern used by hwmon
attributes), so an unlocked debugfs reader can land between a PAGE
write and the subsequent paged read in another thread. READ_STATE
itself is not paged, so it cannot corrupt PAGE in flight, but the
same defensive serialisation that applies to the GPIO accessors
applies here: any direct device access from outside pmbus_core
should be ordered with respect to pmbus_core's own.
Take pmbus_lock at the top of adm1266_state_read() via the
scope-based guard().
Fixes: ed1ff457e187 ("hwmon: (pmbus/adm1266) add debugfs for states")
Cc: stable@vger.kernel.org
Signed-off-by: Abdurrahman Hussain <abdurrahman@nexthop.ai>
Link: https://lore.kernel.org/r/20260518-adm1266-gpio-fixes-v3-8-e425e4f88139@nexthop.ai
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
adm1266_nvmem_read() is the reg_read callback the NVMEM core invokes
when userspace reads /sys/bus/nvmem/devices/.../nvmem on this chip.
On the first byte of every read it does a memset of data->dev_mem,
walks the device blackbox through adm1266_nvmem_read_blackbox()
(which issues a chain of PMBus block transactions), and then memcpys
the refreshed buffer out to userspace. None of that runs under
pmbus_lock today.
Two consequences:
- The PMBus traffic the refresh issues is not serialised against
pmbus_core's own multi-step PAGE+register sequences. A paged
hwmon attribute read from another thread can land between a
PAGE write and the paged read in either direction and corrupt
one side's view of the device state machine.
- The NVMEM core does not serialise concurrent reg_read calls, so
two userspace readers racing at offset 0 can interleave the
memset of data->dev_mem with another reader's
adm1266_nvmem_read_blackbox() refill or memcpy out, returning
torn data to userspace.
Take pmbus_lock at the top of adm1266_nvmem_read() via the
scope-based guard(). Patch 5 of this series moves
adm1266_config_nvmem() past pmbus_do_probe() so the lock is
guaranteed to be live before the callback is reachable from
userspace.
Fixes: 15609d189302 ("hwmon: (pmbus/adm1266) read blackbox")
Cc: stable@vger.kernel.org
Signed-off-by: Abdurrahman Hussain <abdurrahman@nexthop.ai>
Link: https://lore.kernel.org/r/20260518-adm1266-gpio-fixes-v3-7-e425e4f88139@nexthop.ai
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
adm1266_gpio_get(), adm1266_gpio_get_multiple(), and
adm1266_gpio_dbg_show() all issue PMBus reads against the device but
none of them take pmbus_lock. The pmbus_core framework holds
pmbus_lock around its own multi-transaction sequences (notably the
"set PAGE, then read paged register" pattern used by hwmon
attributes), so an unlocked GPIO accessor can land between a PAGE
write and the subsequent paged read in another thread and corrupt
either side's view of the device state machine.
Take pmbus_lock at the top of each of the three accessors via the
scope-based guard(). The lock is uncontended in the common case and
adds only a single mutex round-trip per call.
Fixes: d98dfad35c38 ("hwmon: (pmbus/adm1266) Add support for GPIOs")
Cc: stable@vger.kernel.org
Signed-off-by: Abdurrahman Hussain <abdurrahman@nexthop.ai>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260518-adm1266-gpio-fixes-v3-6-e425e4f88139@nexthop.ai
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
adm1266_probe() calls adm1266_config_nvmem() -- which goes on to
devm_nvmem_register() and exposes adm1266_nvmem_read() to userspace --
before pmbus_do_probe() has initialised the per-client PMBus state.
Same latent hazard as the gpio_chip one fixed in the previous patch:
once the nvmem device is registered, gpiolib's nvmem char-dev / sysfs
interface is reachable, and any concurrent read triggers
adm1266_nvmem_read() -> adm1266_nvmem_read_blackbox(), which issues
PMBus traffic that races pmbus_do_probe()'s own device accesses with
no serialisation.
Move adm1266_config_nvmem() down past pmbus_do_probe() so the nvmem
device isn't reachable from userspace until the PMBus state the
nvmem accessors depend on is fully initialised.
Fixes: 15609d189302 ("hwmon: (pmbus/adm1266) read blackbox")
Cc: stable@vger.kernel.org
Signed-off-by: Abdurrahman Hussain <abdurrahman@nexthop.ai>
Link: https://lore.kernel.org/r/20260518-adm1266-gpio-fixes-v3-5-e425e4f88139@nexthop.ai
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
adm1266_probe() calls adm1266_config_gpio() -- which goes on to
devm_gpiochip_add_data() and exposes the gpio_chip callbacks to
gpiolib -- before pmbus_do_probe() has initialised the per-client
PMBus state (notably the pmbus_lock mutex the core hands out via
pmbus_get_data()).
That ordering is already a latent hazard: any GPIO access that lands
between adm1266_config_gpio() and the end of pmbus_do_probe() (for
example a sysfs read from a user space agent that opens the gpiochip
the instant gpiolib advertises it) races pmbus_do_probe()'s own
device accesses with no serialisation.
Move adm1266_config_gpio() down past pmbus_do_probe() so the chip
isn't reachable from userspace until the PMBus state it depends on
is fully initialised.
Fixes: d98dfad35c38 ("hwmon: (pmbus/adm1266) Add support for GPIOs")
Cc: stable@vger.kernel.org
Signed-off-by: Abdurrahman Hussain <abdurrahman@nexthop.ai>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260518-adm1266-gpio-fixes-v3-4-e425e4f88139@nexthop.ai
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
adm1266_gpio_get() and adm1266_gpio_get_multiple() both compose the
pin-status word as
pins_status = read_buf[0] + (read_buf[1] << 8);
right after i2c_smbus_read_block_data(), guarding only against an
error return. A well-behaved device returns 2 bytes for
GPIO_STATUS/PDIO_STATUS, but the helper happily reports a 0- or
1-byte response too. If the device returns 0 bytes, both read_buf
slots are uninitialized stack memory; if it returns 1 byte, read_buf[1]
is.
The composed value then flows through set_bit() into the caller's
*bits in adm1266_gpio_get_multiple(), or into the return value of
adm1266_gpio_get(), and ends up in userspace via gpiolib (sysfs and
the char-dev ioctls). That leaks a few bits of kernel stack per
request on any device whose firmware glitch, bus error, or hostile
slave produces a short block-read response.
Add the missing length check to both call sites and surface a short
response as -EIO.
Fixes: d98dfad35c38 ("hwmon: (pmbus/adm1266) Add support for GPIOs")
Cc: stable@vger.kernel.org
Signed-off-by: Abdurrahman Hussain <abdurrahman@nexthop.ai>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260518-adm1266-gpio-fixes-v3-3-e425e4f88139@nexthop.ai
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
adm1266_gpio_get_multiple() zeroes *bits before the GPIO_STATUS loop
and then a second time before the PDIO_STATUS loop:
*bits = 0;
for_each_set_bit(gpio_nr, mask, ADM1266_GPIO_NR) {
...
set_bit(gpio_nr, bits);
}
ret = i2c_smbus_read_block_data(data->client, ADM1266_PDIO_STATUS, ...);
...
*bits = 0;
for_each_set_bit_from(gpio_nr, mask, ADM1266_GPIO_NR + ADM1266_PDIO_NR) {
...
set_bit(gpio_nr, bits);
}
The second *bits = 0 throws away every GPIO bit the first loop just
populated, so callers asking for any combination of GPIO and PDIO
pins always see the GPIO portion of the returned bits as zero.
Drop the redundant second assignment so both halves of the result
survive.
Fixes: d98dfad35c38 ("hwmon: (pmbus/adm1266) Add support for GPIOs")
Cc: stable@vger.kernel.org
Signed-off-by: Abdurrahman Hussain <abdurrahman@nexthop.ai>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Reviewed-by: Linus Walleij <linusw@kernel.org>
Link: https://lore.kernel.org/r/20260518-adm1266-gpio-fixes-v3-2-e425e4f88139@nexthop.ai
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
adm1266_gpio_get_multiple() iterates the PDIO portion of the
caller-supplied mask using
for_each_set_bit_from(gpio_nr, mask,
ADM1266_GPIO_NR + ADM1266_PDIO_STATUS) {
...
}
where ADM1266_PDIO_STATUS is the PMBus command code (0xE9, i.e. 233),
not the number of PDIO pins. The intended upper bound is
ADM1266_GPIO_NR + ADM1266_PDIO_NR = 25.
gpiolib hands in a mask sized for gc.ngpio (= 25 bits on this chip),
so the iteration walks find_next_bit() up to 242, reading up to 217
extra bits (a handful of unsigned-long words: four on 64-bit, seven
on 32-bit) of whatever lives past the end of the mask in the
caller's stack. Any incidental set bit in that range then drives a
set_bit(gpio_nr, bits) call that writes past the end of the
caller-supplied bits array too -- both out-of-bounds.
Substitute ADM1266_PDIO_NR for the constant so the scan stops at the
last real PDIO bit.
Fixes: d98dfad35c38 ("hwmon: (pmbus/adm1266) Add support for GPIOs")
Cc: stable@vger.kernel.org
Signed-off-by: Abdurrahman Hussain <abdurrahman@nexthop.ai>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Reviewed-by: Linus Walleij <linusw@kernel.org>
Link: https://lore.kernel.org/r/20260518-adm1266-gpio-fixes-v3-1-e425e4f88139@nexthop.ai
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
adm1266_pmbus_block_xfer() copies the device-supplied block payload
into the caller-provided buffer using the device-supplied length:
memcpy(data_r, &msgs[1].buf[1], msgs[1].buf[0]);
The helper does not know how large data_r is and trusts the device to
return at most one record's worth of bytes. adm1266_nvmem_read_blackbox()
violates that contract: it advances read_buff inside data->dev_mem in
ADM1266_BLACKBOX_SIZE (64-byte) strides while the helper is willing to
write up to ADM1266_PMBUS_BLOCK_MAX (255) bytes. A device that returns
more than 64 bytes on the trailing record (read_buff offset 1984 in
the 2048-byte dev_mem allocation) overflows dev_mem by up to 191 bytes
before the post-call
if (ret != ADM1266_BLACKBOX_SIZE)
return -EIO;
can reject the response.
Contain the fix in the caller without changing the helper signature:
read each record into a 255-byte local bounce buffer that matches the
helper's maximum output, validate the returned length, and only then
copy exactly ADM1266_BLACKBOX_SIZE bytes into the dev_mem slot.
Fixes: 407dc802a9c0 ("hwmon: (pmbus/adm1266) Add Block process call")
Cc: stable@vger.kernel.org
Signed-off-by: Abdurrahman Hussain <abdurrahman@nexthop.ai>
Link: https://lore.kernel.org/r/20260515-adm1266-fixes-v1-5-1c1ea1349cfe@nexthop.ai
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Platforms that fit more than one ADM1266 on different I2C buses at
the same 7-bit slave address (a common shelf-management pattern,
e.g. one device per power domain) end up with duplicate GPIO line
labels because the existing format only includes the slave address.
Including the adapter number disambiguates them.
The adapter number is formatted as decimal to match the i2c-N
convention used elsewhere in Linux (sysfs paths, dev nodes); the
slave address keeps its conventional hexadecimal form.
The label is purely informational (visible via gpioinfo and the
gpiochip /sys/class/gpio name); no DT or ABI consumer parses it.
Fixes: d98dfad35c38c ("hwmon: (pmbus/adm1266) Add support for GPIOs")
Signed-off-by: Abdurrahman Hussain <abdurrahman@nexthop.ai>
Link: https://lore.kernel.org/r/20260512-adm1266-v3-5-a81a479b0bb0@nexthop.ai
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
In xe_oa_stream_open_ioctl(), when param.exec_q->width > 1 the
function returns -EOPNOTSUPP directly, skipping the existing
err_exec_q cleanup path. The exec_queue reference obtained by
xe_exec_queue_lookup() is leaked.
The exec queue holds a reference on the xe_file, which is only
dropped during queue teardown. The leaked lookup ref is not on
the file's exec_queue xarray, so file close cannot release it.
This keeps both the exec queue and the file private state pinned
indefinitely.
Jump to err_exec_q instead of returning directly so the reference
is released.
Fixes: f0ed39830e60 ("xe/oa: Fix query mode of operation for OAR/OAC")
Assisted-by: Claude:claude-opus-4.6
Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Link: https://patch.msgid.link/20260514203210.593488-1-shuicheng.lin@intel.com
Signed-off-by: Shuicheng Lin <shuicheng.lin@intel.com>
(cherry picked from commit 339fa0be9e4a5d69fa47e91f4a36574224fb478f)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
adm1266_pmbus_block_xfer() sets up the read transaction with
.buf = data->read_buf,
.len = ADM1266_PMBUS_BLOCK_MAX + 2,
but read_buf in struct adm1266_data is declared as
u8 read_buf[ADM1266_PMBUS_BLOCK_MAX + 1];
For a max-length block response (length byte = 255 + up to 1 PEC
byte), the i2c controller is told to write 257 bytes into a 256-byte
buffer, putting one byte past the end of read_buf. The same response
also makes the subsequent PEC compare
if (crc != msgs[1].buf[msgs[1].buf[0] + 1])
read a byte beyond the array.
Bump the read_buf declaration to ADM1266_PMBUS_BLOCK_MAX + 2 so the
buffer can hold the length byte, up to 255 payload bytes, and the PEC
byte the i2c_msg length already accounts for.
Fixes: 407dc802a9c0 ("hwmon: (pmbus/adm1266) Add Block process call")
Cc: stable@vger.kernel.org
Signed-off-by: Abdurrahman Hussain <abdurrahman@nexthop.ai>
Link: https://lore.kernel.org/r/20260515-adm1266-fixes-v1-4-1c1ea1349cfe@nexthop.ai
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
adm1266_nvmem_read_blackbox() loops over a record_count that comes
straight from byte 3 of the BLACKBOX_INFO response. The destination
buffer is data->dev_mem, sized for the nvmem cell's declared 2048
bytes (ADM1266_BLACKBOX_MAX_RECORDS * ADM1266_BLACKBOX_SIZE = 32 * 64).
A device that reports a record_count greater than 32 -- whether due
to firmware bugs, bus corruption, or a non-responsive slave returning
0xff -- would walk read_buff past the end of the dev_mem allocation
on the trailing iterations.
Cap record_count at ADM1266_BLACKBOX_MAX_RECORDS (introduced here)
before entering the loop and return -EIO on any larger value, so a
malformed BLACKBOX_INFO response cannot drive the loop out of bounds.
Fixes: 15609d189302 ("hwmon: (pmbus/adm1266) read blackbox")
Cc: stable@vger.kernel.org
Signed-off-by: Abdurrahman Hussain <abdurrahman@nexthop.ai>
Link: https://lore.kernel.org/r/20260515-adm1266-fixes-v1-3-1c1ea1349cfe@nexthop.ai
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
adm1266_nvmem_read_blackbox() declares a 5-byte stack buffer and
passes it to i2c_smbus_read_block_data() to retrieve the 4-byte
BLACKBOX_INFO response. i2c_smbus_read_block_data() does not honour
caller buffer sizes -- it memcpy()s data.block[0] bytes from the
SMBus transaction (where data.block[0] is the length byte returned by
the slave device, up to I2C_SMBUS_BLOCK_MAX = 32):
memcpy(values, &data.block[1], data.block[0]);
If the device returns any block length above 5, the call overflows
the caller's 5-byte stack buffer before the post-call
if (ret != 4)
return -EIO;
check has a chance to reject the response.
Widen the local buffer to I2C_SMBUS_BLOCK_MAX so the helper has room
for any well-formed SMBus block response, matching the convention used
by the other i2c_smbus_read_block_data() callers in this driver.
Fixes: 15609d189302 ("hwmon: (pmbus/adm1266) read blackbox")
Cc: stable@vger.kernel.org
Signed-off-by: Abdurrahman Hussain <abdurrahman@nexthop.ai>
Link: https://lore.kernel.org/r/20260515-adm1266-fixes-v1-2-1c1ea1349cfe@nexthop.ai
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
adm1266_set_rtc() seeds the chip's SET_RTC register from
ktime_get_seconds(), which returns CLOCK_MONOTONIC -- i.e. seconds
since the host last booted, not seconds since the Unix epoch.
The chip stamps that value into every blackbox record it captures.
Userspace reading those timestamps back expects wall-clock seconds:
that's what the SET_RTC frame layout documents (datasheet Rev. D,
Table 84) and what every other consumer of "seconds since epoch"
assumes. Seeding from CLOCK_MONOTONIC gives blackbox records a
timestamp that is only meaningful within a single boot of the host
and silently resets to small values on every reboot.
Switch to ktime_get_real_seconds() so the seed matches what the
register is documented to hold.
Fixes: 15609d189302 ("hwmon: (pmbus/adm1266) read blackbox")
Cc: stable@vger.kernel.org
Signed-off-by: Abdurrahman Hussain <abdurrahman@nexthop.ai>
Link: https://lore.kernel.org/r/20260515-adm1266-fixes-v1-1-1c1ea1349cfe@nexthop.ai
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The EC signature check uses && instead of || between the four
byte comparisons. With &&, the condition is true only when ALL
four bytes fail to match simultaneously, meaning the driver
accepts a device as a valid Microchip EC if ANY single byte of
the 4-byte "MCHP" signature happens to match.
Due to short-circuit evaluation, if the first byte reads back as
'M' (0x4D, a very common register value), the remaining three
comparisons are skipped entirely and the device is accepted.
Change && to || so the check rejects devices that do not fully
match the expected EC signature, as originally intended.
Fixes: 70118f85e6538 ("hwmon: Add EC Chip driver for Lenovo ThinkStation motherboards")
Reviewed-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Signed-off-by: Kean Ren <rh_king@163.com>
Link: https://lore.kernel.org/r/20260521035228.533317-3-rh_king@163.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Replace manual request_region()/release_region() with
devm_request_region(). This lets the device-managed framework
handle I/O region lifetime automatically and fixes:
- A double release_region() when probe fails after acquiring the
I/O region: the probe error path releases it, and then
lenovo_ec_init() releases it again on the same error path.
- A release-after-use window in lenovo_ec_exit() where
release_region() was called before platform_device_unregister(),
leaving the hwmon device active with a released I/O region.
- Missing release_region() in lenovo_ec_probe() if
devm_hwmon_device_register_with_info() fails.
Remove all four manual release_region() calls that are now handled
automatically and replace request_region with
devm_request_region, use dev_err replace pr_err.
Also remove the now-unnecessary braces around the single-statement
if body.
Fixes: 70118f85e6538 ("hwmon: Add EC Chip driver for Lenovo ThinkStation motherboards")
Reviewed-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Signed-off-by: Kean Ren <rh_king@163.com>
Link: https://lore.kernel.org/r/20260521035228.533317-2-rh_king@163.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Commit 1feda5eb77fc ("drm/exynos: Use selected dma_dev default iommu
domain instead of a fake one") removed the code around creating a
custom IOMMU domain, but forgot to remove the stub.
Remove the iommu_dma_init_domain() stub as the function is no longer
referenced, and was also made private to the IOMMU DMA code.
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
u2fzero_fill_in_urb() allocates dev->urb with usb_alloc_urb(), but
u2fzero_probe() ignored its return value and only freed the URB from
u2fzero_remove().
If LED or hwrng registration fails after the URB allocation, probe returns
an error and the driver core does not call .remove(), leaking the URB. A
failed URB setup was also allowed to continue probing with an unusable
device.
Check the URB setup result and add the missing probe-error unwind so the
URB is freed before returning from later errors.
Signed-off-by: Myeonghun Pak <mhun512@gmail.com>
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
|
