| Age | Commit message (Collapse) | Author |
|---|
|
Nothing uses this, just dead code.
Reviewed-by: Mostafa Saleh <smostafa@google.com>
Reviewed-by: Pranjal Shrivastava <praan@google.com>
Tested-by: Pranjal Shrivastava <praan@google.com>
Tested-by: Mostafa Saleh <smostafa@google.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Nicolin Chen <nicolinc@nvidia.com>
Tested-by: Samiullah Khawaja <skhawaja@google.com>
Tested-by: Nicolin Chen <nicolinc@nvidia.com>
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Convert the batch's type to also get the remaining helper functions to
use the new type and complete replacing naked u64s with the new struct.
The low-level queue_write()/queue_read()/queue_remove_raw() functions
remain u64-based since they are shared by event and PRI queues which
have different entry sizes.
Reviewed-by: Mostafa Saleh <smostafa@google.com>
Reviewed-by: Pranjal Shrivastava <praan@google.com>
Tested-by: Pranjal Shrivastava <praan@google.com>
Tested-by: Mostafa Saleh <smostafa@google.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Nicolin Chen <nicolinc@nvidia.com>
Tested-by: Samiullah Khawaja <skhawaja@google.com>
Tested-by: Nicolin Chen <nicolinc@nvidia.com>
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Continue removing struct arm_smmu_cmdq_ent in favour of the HW based
struct arm_smmu_cmd. Switch the lower level issue commands to work on
the native struct by lifting arm_smmu_cmdq_build_cmd() into all the
callers.
Following patches will revise each of the arm_smmu_cmdq_build_cmd()
call sites to replace it with the HW struct.
Reviewed-by: Mostafa Saleh <smostafa@google.com>
Reviewed-by: Pranjal Shrivastava <praan@google.com>
Tested-by: Pranjal Shrivastava <praan@google.com>
Tested-by: Mostafa Saleh <smostafa@google.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Nicolin Chen <nicolinc@nvidia.com>
Tested-by: Samiullah Khawaja <skhawaja@google.com>
Tested-by: Nicolin Chen <nicolinc@nvidia.com>
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Start removing the use of struct arm_smmu_cmdq_ent, starting at the
lower levels of the call chain. Change the functions that determine what
cmdq to issue the batch to into using struct arm_smmu_cmd directly.
Reviewed-by: Pranjal Shrivastava <praan@google.com>
Reviewed-by: Mostafa Saleh <smostafa@google.com>
Tested-by: Pranjal Shrivastava <praan@google.com>
Tested-by: Mostafa Saleh <smostafa@google.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Nicolin Chen <nicolinc@nvidia.com>
Tested-by: Samiullah Khawaja <skhawaja@google.com>
Tested-by: Nicolin Chen <nicolinc@nvidia.com>
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Like STE/CD, add a wrapper struct around the u64 array to represent the
already FIELD_PREP'd command data. Unlike the STE/CD this is a u64
because the command submission path will have the swap to le64.
This makes the API clearer when a u64 is referring to a formatted
command and makes the following changes easier to follow.
Move the command constants out of the struct and into an enum alongside
the rest of the constants defining the HW format so the entire HW format
is self contained and independent of struct arm_smmu_cmdq_ent.
Reviewed-by: Samiullah Khawaja <skhawaja@google.com>
Reviewed-by: Mostafa Saleh <smostafa@google.com>
Reviewed-by: Nicolin Chen <nicolinc@nvidia.com>
Reviewed-by: Pranjal Shrivastava <praan@google.com>
Tested-by: Pranjal Shrivastava <praan@google.com>
Tested-by: Mostafa Saleh <smostafa@google.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Tested-by: Samiullah Khawaja <skhawaja@google.com>
Tested-by: Nicolin Chen <nicolinc@nvidia.com>
Signed-off-by: Will Deacon <will@kernel.org>
|
|
After a PCIe Uncorrectable Error has been reported by a device with
Intel Vendor Specific Extended Capabilities and has been recovered
through a Secondary Bus Reset, its driver calls intel_vsec_pci_probe()
to rescan and reinitialize VSECs.
intel_vsec_pci_probe() invokes pcim_enable_device() and thereby adds
another devm action which calls pcim_disable_device() on driver unbind.
So once the driver unbinds, pcim_disable_device() will be called as many
times as an Uncorrectable Error occurred, plus one. This will lead to
an enable_cnt imbalance on driver unbind.
Additionally, since commit dc957ab6aa05 ("platform/x86/intel/vsec: Add
private data for per-device data"), a devm_kzalloc() allocation is
leaked on every Uncorrectable Error.
Avoid by splitting the VSEC rescan out of intel_vsec_pci_probe() into a
separate helper and calling that on PCIe error recovery.
Fixes: 936874b77dd0 ("platform/x86/intel/vsec: Add PCI error recovery support to Intel PMT")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v6.0+
Link: https://patch.msgid.link/bd594d09fa866dc51dddc9a447c3b23f9b1402cc.1778736835.git.lukas@wunner.de
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
It seems that on some older models (~2020) the battery charging limit
can permanently damage the battery. Prevent users from enabling this
feature thru the "force" module parameter to avoid causing permanent
hardware damage on such devices.
Fixes: d050479693bb ("platform/x86: Add Uniwill laptop driver")
Link: https://www.reddit.com/r/XMG_gg/comments/ld9yyf/battery_limit_hidden_function_discovered_on/
Reviewed-by: Werner Sembach <wse@tuxedocomputers.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://patch.msgid.link/20260512232145.329260-5-W_Armin@gmx.de
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Users might want to force-enable all possible features even on
machines with a valid device descriptor. Until now the "force"
module param was ignored on such machines. Fix this to make
it easier to test for support of new features.
Fixes: d050479693bb ("platform/x86: Add Uniwill laptop driver")
Reviewed-by: Werner Sembach <wse@tuxedocomputers.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://patch.msgid.link/20260512232145.329260-4-W_Armin@gmx.de
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
The power supply sysfs ABI states that:
Not all hardware is capable of setting this to an arbitrary
percentage. Drivers will round written values to the nearest
supported value. Reading back the value will show the actual
threshold set by the driver.
The driver currently violates this ABI by rejecting a charging
threshold of 0. Fix this by clamping this value to 1.
Fixes: d050479693bb ("platform/x86: Add Uniwill laptop driver")
Reviewed-by: Werner Sembach <wse@tuxedocomputers.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://patch.msgid.link/20260512232145.329260-3-W_Armin@gmx.de
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
The EC might initialize the charge threshold with 0 to signal that
said threshold is uninitialized. Detect this and replace said value
with 100 to signal the EC that we want to take control of battery
charging. Also set the threshold to 100 if the EC-provided value
is invalid.
Fixes: d050479693bb ("platform/x86: Add Uniwill laptop driver")
Reviewed-by: Werner Sembach <wse@tuxedocomputers.com>
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://patch.msgid.link/20260512232145.329260-2-W_Armin@gmx.de
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Every platform driver can be forced to match a device that doesn't match
its list of device IDs because of device_match_driver_override(), so
platform drivers that rely on the existence of a device's ACPI companion
object need to verify its presence.
Accordingly, add a requisite ACPI_COMPANION() check against NULL to the
surfacepro3_button driver.
Fixes: d913a5a12b40 ("platform/surface: surfacepro3_button: Convert to a platform driver")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Chen Yu <yu.c.chen@intel.com>
Link: https://patch.msgid.link/23119222.EfDdHjke4D@rafael.j.wysocki
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Every platform driver can be forced to match a device that doesn't match
its list of device IDs because of device_match_driver_override(), so
platform drivers that rely on the existence of a device's ACPI companion
object need to verify its presence.
Accordingly, add a requisite ACPI_HANDLE() check against NULL to the
platform/x86 intel-vbtn driver.
Fixes: 26173179fae1 ("platform/x86: intel-vbtn: Eval VBDL after registering our notifier")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/3426431.aeNJFYEL58@rafael.j.wysocki
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Every platform driver can be forced to match a device that doesn't match
its list of device IDs because of device_match_driver_override(), so
platform drivers that rely on the existence of a device's ACPI companion
object need to verify its presence.
Accordingly, add a requisite ACPI_HANDLE() check against NULL to the
platform/x86 intel_sar driver.
Fixes: dcfbd31ef4bc ("platform/x86: BIOS SAR driver for Intel M.2 Modem")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/14023870.uLZWGnKmhe@rafael.j.wysocki
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Every platform driver can be forced to match a device that doesn't match
its list of device IDs because of device_match_driver_override(), so
platform drivers that rely on the existence of a device's ACPI companion
object need to verify its presence.
Accordingly, add a requisite ACPI_HANDLE() check against NULL to the
platform/x86 intel-hid driver.
Fixes: ecc83e52b28c ("intel-hid: new hid event driver for hotkeys")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/1971512.tdWV9SEqCh@rafael.j.wysocki
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Every platform driver can be forced to match a device that doesn't match
its list of device IDs because of device_match_driver_override(), so
platform drivers that rely on the existence of a device's ACPI companion
object need to verify its presence.
Accordingly, add a requisite ACPI_COMPANION() check against NULL to the
platform/x86 hp_accel driver.
Fixes: 8ebcb6c94c71 ("platform/x86: hp_accel: Convert to be a platform driver")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/2425918.ElGaqSPkdT@rafael.j.wysocki
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Every platform driver can be forced to match a device that doesn't match
its list of device IDs because of device_match_driver_override(), so
platform drivers that rely on the existence of a device's ACPI companion
object need to verify its presence.
Accordingly, add a requisite ACPI_HANDLE() check against NULL to the
platform/x86 adv_swbutton driver.
Fixes: 3d904005f686 ("platform/x86: add support for Advantech software defined button")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/5115425.31r3eYUQgx@rafael.j.wysocki
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
The HP Omen 16-c0xxx (board ID: 8902) has the same WMI interface as
other Victus S boards, but requires additional quirks for correctly
switching thermal profile.
Add the DMI board name to victus_s_thermal_profile_boards[] table and
map it to the omen_v1_legacy_thermal_params quirk.
Testing on board 8902 confirmed that platform profile is registered
successfully and fan RPMs are readable and controllable.
Signed-off-by: Konenko Andrey Viktorovich <admin@aquinas.su>
Link: https://patch.msgid.link/T3DTKbKwQzOgk_0eUG-kMg@aquinas.su
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
The fwctl core allocates the device-specific RPC input buffer with
fwctl_rpc.in_len and passes that buffer to the driver callback.
pdsfc_fw_rpc() casts the buffer to struct fwctl_rpc_pds and then calls
pdsfc_validate_rpc(), which reads fields from that structure before
checking that the input buffer is large enough to contain it. A short
in_len can make pds_fwctl read beyond the allocation.
Reject pds RPC buffers that are smaller than struct fwctl_rpc_pds before
parsing any pds-specific fields.
Fixes: 92c66ee829b9 ("pds_fwctl: add rpc and query support")
Link: https://patch.msgid.link/r/20260517062232.1858747-1-gganji11@naver.com
Cc: stable@vger.kernel.org # v6.15+
Signed-off-by: Heechan Kang <gganji11@naver.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
|
|
Replace the custom open function and file_operations with the standard
DEFINE_SHOW_ATTRIBUTE macro to reduce boilerplate code.
This also adds the previously missing .release() callback and fixes the
seq_file leak during close.
Signed-off-by: Hans Zhang <18255117159@163.com>
[mani: added a note about implicit release callback change spotted by Sashiko]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://patch.msgid.link/20260508133432.1964491-1-18255117159@163.com
|
|
Laptop 7
Surface Laptop 7 exposes battery and AC status via Qualcomm PMIC GLINK
qcom_battmgr. Registering the standard SSAM battery and AC client
devices on this platform causes duplicate power-supply devices to
appear.
Drop the SSAM battery and AC nodes from the Surface Laptop 7 registry
group so that only the qcom_battmgr power supplies are instantiated.
Fixes: b27622f13172 ("platform/surface: Add OF support")
Signed-off-by: Oliver White <oliverjwhite07@gmail.com>
Link: https://patch.msgid.link/20260409034347.17381-1-oliverjwhite07@gmail.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
coresight_add_out_conn() increments nr_outconns before calling
devm_krealloc_array() and again before devm_kmalloc(). If either
allocation fails, the counter is already bumped while the corresponding
array entry is NULL or uninitialized garbage.
coresight_add_in_conn() has the same problem with nr_inconns and
devm_krealloc_array().
In both cases the probe returns -ENOMEM, which causes
coresight_get_platform_data() to call coresight_release_platform_data()
for cleanup. That function iterates up to nr_outconns (or nr_inconns)
entries and dereferences each pointer unconditionally, hitting the NULL
or garbage entry and panicking instead of failing gracefully.
Fix by moving the counter increments to after all allocations succeed,
so the struct is always consistent on any error path.
Fixes: 3d4ff657e454 ("coresight: Dynamically add connections")
Fixes: e3f4e68797a9 ("coresight: Store in-connections as well as out-connections")
Signed-off-by: Jie Gan <jie.gan@oss.qualcomm.com>
Reviewed-by: James Clark <james.clark@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20260511-fix-ref-count-issue-v1-1-99d647810d3c@oss.qualcomm.com
|
|
Praveen Talari <praveen.talari@oss.qualcomm.com> says:
Add tracepoints to the Qualcomm GENI (Generic Interface) SPI driver.
These trace events enable runtime debugging and performance analysis
of SPI operations.
The trace events capture SPI clock configuration, setup parameters,
transfer details, interrupt status.
Usage examples:
Enable all SPI traces:
echo 1 > /sys/kernel/tracing/events/spi/enable
echo 1 > /sys/kernel/debug/tracing/events/qcom_geni_spi/enable
cat /sys/kernel/debug/tracing/trace_pipe
Example trace output:
1003.956560: spi_message_submit: spi16.0 000000001b20b93c
1003.956642: spi_controller_busy: spi16
1003.956643: spi_message_start: spi16.0 000000001b20b93c
1003.956646: geni_spi_setup_params: 888000.spi: cs=0 mode=0x00000020
mode_changed=0x00000007 cs_changed=0
1003.956647: spi_set_cs: spi16.0 activate
1003.956648: spi_transfer_start: spi16.0 00000000ea1cf8b6 len=16
tx=[4c-80-e4-ca-68-4d-95-aa-ee-99-ae-d7-69-e9-5f-39]
rx=[00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00]
1003.956653: geni_spi_clk_cfg: 888000.spi: req_hz=20000000
sclk_hz=100000000 clk_idx=5 clk_div=5 bpw=8
1003.956691: geni_spi_transfer: 888000.spi: len=16 m_cmd=0x00000003
1003.956708: geni_spi_irq: 888000.spi: m_irq=0x08000081
dma_tx=0x00000000 dma_rx=0x00000000
1003.956717: spi_transfer_stop: spi16.0 00000000ea1cf8b6 len=16
tx=[4c-80-e4-ca-68-4d-95-aa-ee-99-ae-d7-69-e9-5f-39]
rx=[4c-80-e4-ca-68-4d-95-aa-ee-99-ae-d7-69-e9-5f-39]
1003.956717: spi_set_cs: spi16.0 deactivate
1003.956718: spi_message_done: spi16.0 000000001b20b93c len=16/16
Link: https://patch.msgid.link/20260518-add-tracepoints-for-qcom-geni-spi-v3-0-7928f6810a79@oss.qualcomm.com
|
|
Add tracepoints to the Qualcomm GENI (Generic Interface) SPI driver.
These trace events enable runtime debugging and performance analysis
of SPI operations.
The trace events capture SPI clock configuration, setup parameters,
transfer details, interrupt status.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Praveen Talari <praveen.talari@oss.qualcomm.com>
Link: https://patch.msgid.link/20260518-add-tracepoints-for-qcom-geni-spi-v3-2-7928f6810a79@oss.qualcomm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
PTL with physically disconnected display was observed to have 40s longer
execution time when testing xe_fault_injection@xe_guc_mmio_send_recv.
The issue has not been seen when reverting commit 40a9f77a28fa ("Revert
"drm/i915/dp: change aux_ctl reg read to polling read"").
Apparently the configuration suffers from not having AUX enabled when
using interrupts. One probable cause can be xe enabling interrupts too
late: interrupts need memory allocations which currently can't be done
before the display FB takeover is done.
As for now, use polling for AUX in case interrupts are unavailable.
Fixes: 40a9f77a28fa ("Revert "drm/i915/dp: change aux_ctl reg read to polling read"")
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Michał Grzelak <michal.grzelak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20260416163744.288107-1-michal.grzelak@intel.com
|
|
Introduce USB4STREAM protocol and Linux implementation. This allows two
(or more) hosts to transfer data directly over Thunderbolt/USB4 cable
through a character device without need to go through the network stack.
Any application that supports read(2) and write(2) in some form should
be able to use the device without changes. The data is sent out to the
other side over a tunnel inside Thunderbolt/USB4 fabric. The character
device is called /dev/tbstreamX where X is the minor number starting
from 0.
All stream devices need to be configured first. This is done through
ConfigFS interface. There can be multiple streams at the same time (this
depends on number of DMA rings and available HopIDs) and a single stream
supports traffic in both directions. For example there could be an
application that uses one stream as control channel and another one as
bi-directional data channel.
A real use-case for this is to take a backup as a part of recovery
initramfs tooling (no need to setup networking or have ssh or similar
tooling as part of the initramfs). Say we want to backup the disk of
host1 to host2. First Thunderbolt/USB4 cable is connected between the
hosts (there can be devices in the middle too) then the receiving side
configures the stream:
host2 # mkdir /sys/kernel/config/thunderbolt/stream/0-1.0
host2 # mkdir /sys/kernel/config/thunderbolt/stream/0-1.0/backup
host2 # echo -1 > /sys/kernel/config/thunderbolt/stream/0-1.0/backup/in_hopid
host2 # echo -1 > /sys/kernel/config/thunderbolt/stream/0-1.0/backup/out_hopid
We use automatic HopID allocation (writing -1 to HopIDs) for simplicity.
From this point forward the /dev/tbstream0 can be used pretty much as
regular file:
host2 # dd if=/dev/tbstream0 of=/tmp/host1.nvme0n1.backup-$(date +%F) bs=256k
The host that is being backed up then configures the stream accordingly:
host1 # mkdir /sys/kernel/config/thunderbolt/stream/0-503.0
host1 # mkdir /sys/kernel/config/thunderbolt/stream/0-503.0/backup
Here we take advantage of the fact that host2 also announces the active
streams through XDomain properties so the name "backup" gives us the
HopIDs. It is also possible to configure them manually in the same way
we did for host2.
Then it is just a matter of copying the data over:
host1 # dd if=/dev/nvme0n1 of=/dev/tbstream0 bs=256k
Similarly it is possible to transfer parts of the filesystem. For
example copy contents of mydir over to the host2:
host2 # gunzip < /dev/tbstream0 | tar xf -
host1 # tar cf - mydir | gzip > /dev/tbstream0
Other end of the spectrum use-case is "borrowing" laptop (host1) camera
to desktop (host2):
host2 # gst-launch-1.0 filesrc location=/dev/tbstream0 ! jpegdec ! videoconvert ! \
autovideosink
host1 # gst-launch-1.0 v4l2src device=/dev/video0 ! video/x-raw,width=1920,height=1080 ! \
jpegenc quality=90 ! filesink location=/dev/tbstream0
Once the streams are no longer needed they can be removed:
host1 # cd /sys/kernel/config/thunderbolt/stream/
host1 # rmdir -p 0-503.0/backup
host2 # cd /sys/kernel/config/thunderbolt/stream
host2 # rmdir -p 0-1.0/backup
Co-developed-by: Alan Borzeszkowski <alan.borzeszkowski@linux.intel.com>
Signed-off-by: Alan Borzeszkowski <alan.borzeszkowski@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
This adds ConfigFS support to USB4/Thunderbolt bus. By itself this just
creates the subsystem but it exposes functions that can be used to
register groups under it.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
This allows the caller to wait for the ring to be empty. We are going to
need this in the upcoming userspace tunneling support.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Instead of the core driver programming fixed value for throttling let
the service drivers to specify the interval if they need this.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
This function can be used outside of thunderbolt networking driver so
move it to the common header.
No functional changes.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
The XDomain properties can be useful for service drivers, for example to
implement a registry for the services they expose. So far there has been
no need for service drivers to specify these but with the USB4STREAM
driver that we are going to use them.
This adds remote and local side properties that the service drivers have
access to. Remote side is read-only but the local side can be changed by
a service driver. Also provide a mechanism to notify the remote side
that there are changes.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
This makes sure it keeps working if we ever need to change it.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
This allows merging one XDomain property directory into another. We are
going to use this in the subsequent patch.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
In addition to updating the CPU MPAM version check, the MPAM MSC version
check also need to be updated. mpam_msc_check_aidr() is added to check
the MSC AIDR register, ensuring that both the major and minor version
numbers fall within the supported range of the MPAM architecture version.
Signed-off-by: Zeng Heng <zengheng4@huawei.com>
[ morse: changed mpam_msc_check_aidr() to accept versions like v1.2 ]
Signed-off-by: James Morse <james.morse@arm.com>
Reviewed-by: Ben Horgan <ben.horgan@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Stop retrying queue allocation when qsz reaches PAGE_SIZE.
Signed-off-by: Leo Jiang <leo.jiang1224@foxmail.com>
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Antonio Quartulli says:
====================
Included fixes:
* fix TCP selftest failures by reducing number of attempted pings
* fix RCU ptr deref outside of RCU read section
* fix UAF in case of TCP peer failed to be added to hashtable
* fix race condition between iface teardown and new peer being added
* ensure dstats are updated with BH disabled to avoid concurrency
* tag 'ovpn-net-20260514' of https://github.com/OpenVPN/ovpn-net-next:
ovpn: disable BHs when updating device stats
ovpn: fix race between deleting interface and adding new peer
ovpn: respect peer refcount in CMD_NEW_PEER error path
ovpn: tcp - use cached peer pointer in ovpn_tcp_close()
selftests: ovpn: reduce remaining ping flood counts
====================
Link: https://patch.msgid.link/20260514231544.795993-1-antonio@openvpn.net
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
With DRM_AMDGPU=m and DRM_AMD_ISP=y, it is possible to configura
VIDEO_AMD_ISP4_CAPTURE as built-in, but that fails to link:
aarch64-linux-ld: drivers/media/platform/amd/isp4/isp4_interface.o: in function `isp4if_gpu_mem_alloc.isra.0':
isp4_interface.c:(.text+0x1d0): undefined reference to `isp_kernel_buffer_alloc'
aarch64-linux-ld: drivers/media/platform/amd/isp4/isp4_interface.o: in function `isp4if_dealloc_fw_gpumem':
isp4_interface.c:(.text+0x26c): undefined reference to `isp_kernel_buffer_free'
Add a dependency on the tristate DRM_AMDGPU symbol in addition to
the boolean DRM_AMD_ISP=y, so this can only be built-in if
the ISP driver is also linked into the kernel itself.
Fixes: 9a54c285630c ("media: platform: amd: Introduce amd isp4 capture driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Bin Du <Bin.Du@amd.com>
Tested-by: Bin Du <Bin.Du@amd.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
|
|
Newer Smatch snapshots no longer report the false positive around
isp4if_send_fw_cmd(), so the extra list reinitialization before kfree()
is no longer needed.
Drop the stale list reinit and keep the cleanup path simpler.
Signed-off-by: Bin Du <Bin.Du@amd.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
|
|
The OV13B10 sensor driver currently handles a single regulator called
avdd, however the sensor can be supplied by up to three regulators.
Update the driver to handle all of them together using the regulator
bulk API.
Signed-off-by: Arun T <arun.t@intel.com>
Reviewed-by: Hans de Goede <johannes.goede@oss.qualcomm.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
|
|
The Intel NVL platform uses IPU8 powered by a TPS68470 PMIC,
requiring board data to configure the GPIOs and regulators for
proper camera sensor operation.
Signed-off-by: Arun T <arun.t@intel.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Reviewed-by: Hans de Goede <johannes.goede@oss.qualcomm.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
|
|
Rename the MSI-specific daisy-chain GPIO properties and software node
to generic names so they can be reused by other platforms that also
require daisy-chain GPIO configuration for TPS68470.
Signed-off-by: Arun T <arun.t@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
|
|
Add support for the new CEC LIP opcodes.
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Link: https://patch.msgid.link/9fb27f4a2133cf46b8e0fc126c2d1ef8b1bc30e1.1779115235.git.hverkuil+cisco@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Message-ID: <9fb27f4a2133cf46b8e0fc126c2d1ef8b1bc30e1.1779115235.git.hverkuil+cisco@kernel.org>
|
|
Add support for workload submission trace points.
Co-developed-by: Donald Robson <donald.robson@imgtec.com>
Signed-off-by: Donald Robson <donald.robson@imgtec.com>
Signed-off-by: Alexandru Dadu <alexandru.dadu@imgtec.com>
Reviewed-by: Matt Coster <matt.coster@imgtec.com>
Link: https://patch.msgid.link/20260513-b4-pvr-trace-points-v1-1-81222d1a4c99@imgtec.com
Signed-off-by: Matt Coster <matt.coster@imgtec.com>
|
|
arm_smmu_write_context_bank() assumes it is being called with RPM
active, but it turns out that is not guaranteed in the path from
qcom_adreno_smmu_set_ttbr0_cfg(), so it's possible for the register
writes to get lost when configuring the context bank while the GPU is
idle, leading to page faults later.
Add the RPM calls here to make sure the SMMU is active before we touch
it.
Signed-off-by: Anna Maniscalco <anna.maniscalco2000@gmail.com>
Reviewed-by: Rob Clark <rob.clark@oss.qualcomm.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Update FW initialised state shared resource access with READ/WRITE_ONCE
to prevent following:
- Non-atomic access to variable in multi-thread/CPU case.
- Merge successive loads from the same variable.
Signed-off-by: Brajesh Gupta <brajesh.gupta@imgtec.com>
Reviewed-by: Matt Coster <matt.coster@imgtec.com>
Link: https://patch.msgid.link/20260519-b4-context_reset-v2-4-931018a7131d@imgtec.com
Signed-off-by: Matt Coster <matt.coster@imgtec.com>
|
|
Rename the variable from 'booted' to 'initialised' to align with the
driver's expectations and state, indicating that FW boot initialisation
is complete and the firmware is fully initialised.
Signed-off-by: Brajesh Gupta <brajesh.gupta@imgtec.com>
Reviewed-by: Matt Coster <matt.coster@imgtec.com>
Link: https://patch.msgid.link/20260519-b4-context_reset-v2-3-931018a7131d@imgtec.com
Signed-off-by: Matt Coster <matt.coster@imgtec.com>
|
|
Verify the job’s fence in the timeout handler; if the firmware has since
signaled completion, then report NO HANG.
Signed-off-by: Brajesh Gupta <brajesh.gupta@imgtec.com>
Reviewed-by: Matt Coster <matt.coster@imgtec.com>
Link: https://patch.msgid.link/20260519-b4-context_reset-v2-2-931018a7131d@imgtec.com
Signed-off-by: Matt Coster <matt.coster@imgtec.com>
|
|
Initialise the context ID for the FW common context correctly by moving
the context allocation earlier.
Signed-off-by: Brajesh Gupta <brajesh.gupta@imgtec.com>
Reviewed-by: Matt Coster <matt.coster@imgtec.com>
Link: https://patch.msgid.link/20260519-b4-context_reset-v2-1-931018a7131d@imgtec.com
Signed-off-by: Matt Coster <matt.coster@imgtec.com>
|
|
Use LIST_HEAD to initialize on stack list head. No intentional
functional impact.
Change generated with below coccinelle script:
@@
identifier name;
@@
- struct list_head name;
+ LIST_HEAD(name);
... when != name
- INIT_LIST_HEAD(&name);
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Message-ID: <20260519055722.13161-1-jszhang@kernel.org>
Signed-off-by: Corey Minyard <corey@minyard.net>
|
|
The retry count was initially set to 10, which with the 5 second
timeouts give 55 seconds to fail a message.
The IPMI spec specifies the 5 second timeout, and it specifies retries
for KCS but does not specify a number. 55 seconds is a long time, so
reduce retries to 2. It matches the default in the BT state machine.
This is 15 seconds, then, which is still a long time, but more
reasonable.
Signed-off-by: Corey Minyard <corey@minyard.net>
|
|
This set of tests require userspace memory to map objects, so
run them only if this that memory is available.
Signed-off-by: Krzysztof Karas <krzysztof.karas@intel.com>
Reviewed-by: Sebastian Brzezinka <sebastian.brzezinka@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Reviewed-by: Janusz Krzysztofik <janusz.krzysztofik@linux.intel.com>
Reviewed-by: Michał Grzelak <michal.grzelak@intel.com>
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Link: https://lore.kernel.org/r/20260508080214.1979686-3-krzysztof.karas@intel.com
|
