| Age | Commit message (Collapse) | Author |
|---|
|
snd_wss_resume() restores only the codec register image. The SC-6000
driver also programs card-specific DSP routing and enters MSS mode
during probe, and that setup is not replayed after suspend.
Cache the WSS chip pointer in the SC-6000 card state and wire ISA
suspend and resume callbacks to the shared board-programming helper,
so the board is reinitialized before the codec state is restored.
This keeps the old/new DSP split in one place and restores the
board-level MSS setup that the codec resume path does not cover.
Signed-off-by: Cássio Gabriel <cassiogabrielcontato@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20260410-alsa-sc6000-pm-v1-2-4d9e95493d26@gmail.com
|
|
The driver may auto-select IRQ and DMA resources at probe time, but
sc6000_init_board() still derives the SC-6000 soft configuration from
the module parameter arrays. When irq=auto or dma=auto is used, the
codec is created with the selected resources while the board is
programmed with the unresolved values.
Store the mapped ports and generated SC-6000 board configuration in
card-private data, build that configuration from the live probe
results instead of the raw module parameters, and keep the probe-time
board programming in a shared helper.
This fixes the resource-programming mismatch and leaves the driver
with a stable board-state block that can be reused by suspend/resume.
Fixes: c282866101bf ("ALSA: sc6000: add support for SC-6600 and SC-7000")
Signed-off-by: Cássio Gabriel <cassiogabrielcontato@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20260410-alsa-sc6000-pm-v1-1-4d9e95493d26@gmail.com
|
|
In usb6fire_chip_abort(), the chip struct is allocated as the card's
private data (via snd_card_new with sizeof(struct sfire_chip)). When
snd_card_free_when_closed() is called and no file handles are open, the
card and embedded chip are freed synchronously. The subsequent
chip->card = NULL write then hits freed slab memory.
Call trace:
usb6fire_chip_abort sound/usb/6fire/chip.c:59 [inline]
usb6fire_chip_disconnect+0x348/0x358 sound/usb/6fire/chip.c:182
usb_unbind_interface+0x1a8/0x88c drivers/usb/core/driver.c:458
...
hub_event+0x1a04/0x4518 drivers/usb/core/hub.c:5953
Fix by moving the card lifecycle out of usb6fire_chip_abort() and into
usb6fire_chip_disconnect(). The card pointer is saved in a local
before any teardown, snd_card_disconnect() is called first to prevent
new opens, URBs are aborted while chip is still valid, and
snd_card_free_when_closed() is called last so chip is never accessed
after the card may be freed.
Fixes: a0810c3d6dd2 ("ALSA: 6fire: Release resources at card release")
Cc: stable@vger.kernel.org
Cc: Andrey Konovalov <andreyknvl@gmail.com>
Signed-off-by: Berk Cem Goksel <berkcgoksel@gmail.com>
Link: https://patch.msgid.link/20260410051341.1069716-1-berkcgoksel@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The status field in an EFW response is a 32-bit value supplied by the
firewire device. efr_status_names[] has 17 entries so a status value
outside that range goes off into the weeds when looking at the %s value.
Even worse, the status could return EFR_STATUS_INCOMPLETE which is
0x80000000, and is obviously not in that array of potential strings.
Fix this up by properly bounding the index against the array size and
printing "unknown" if it's not recognized.
Cc: Clemens Ladisch <clemens@ladisch.de>
Cc: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Fixes: bde8a8f23bbe ("ALSA: fireworks: Add transaction and some commands")
Cc: stable <stable@kernel.org>
Assisted-by: gregkh_clanker_t1000
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://patch.msgid.link/2026040953-astute-camera-1aa1@gregkh
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
A malicious USB device with the TASCAM US-144MKII device id can have a
configuration containing bInterfaceNumber=1 but no interface 0. USB
configuration descriptors are not required to assign interface numbers
sequentially, so usb_ifnum_to_if(dev, 0) returns will NULL, which will
then be dereferenced directly.
Fix this up by checking the return value properly.
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Fixes: dee1bcf28a3d ("ALSA: usb-audio: Add initial driver for TASCAM US-144MKII")
Cc: stable <stable@kernel.org>
Assisted-by: gregkh_clanker_t1000
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://patch.msgid.link/2026040955-fall-gaining-e338@gregkh
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
When reporting the pointer for a compressed stream we report the current
I/O frame position by dividing the position by the number of channels
multiplied by the number of container bytes. These values default to 0 and
are only configured as part of setting the stream parameters so this allows
a divide by zero to be configured. Validate that they are non zero,
returning an error if not
Fixes: c1a731c71359 ("ASoC: SOF: compress: Add support for computing timestamps")
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20260326-asoc-compress-tstamp-params-v1-1-3dc735b3d599@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add an approach to get new hardware advance gain,
and if there is no advance gain with this approach,
we can still get advance gain with original method.
Signed-off-by: Jack Yu <jack.yu@realtek.com>
Link: https://patch.msgid.link/20260410064225.662656-1-jack.yu@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
A couple of attempts to correct this FIXME have been sent upstream but
the situation is not quite a simple as the FIXME implies. Update the
FIXME to include a better description of the situation.
Link: https://lore.kernel.org/linux-sound/20260408085607.3813488-1-shumingf@realtek.com/
Link: https://lore.kernel.org/linux-sound/20260324-sdca-function-status-init-irq-v1-1-bba49417a4e0@gmail.com/
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20260410104500.163337-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add the MSI Vector A16 HX A8WHG (board MS-15MM) to the DMI quirk table
to enable DMIC support. This laptop uses an AMD Ryzen 9 7945HX (Dragon
Range) with the ACP6x audio coprocessor (rev 0x62) and a Realtek ALC274
codec. The built-in digital microphone is connected via the ACP PDM
interface and requires this DMI entry to be activated.
Tested on MSI Vector A16 HX A8WHG with kernel 6.8.0-107 (Ubuntu 24.04).
DMIC capture device appears as 'acp6x' and records audio correctly.
Signed-off-by: Ihor Uzlov <igor.uzlov@gmail.com>
Link: https://patch.msgid.link/20260410094553.24654-1-igor.uzlov@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This codec driver depended on the legacy GPIO API, and nothing
in the kernel is defining the platform data, so get rid of this.
Two in-kernel device trees are defining this codec using
undocumented device tree properties, so support these for now.
The same properties can be defined using software nodes if board
files are desired. The device tree use the "-gpio" rather than
"-gpios" suffix but the GPIO DT parser will deal with that.
Since there may be out of tree users, migrate to GPIO descriptors,
drop the platform data that is unused, and assign the dac_clk the
value that was used in all platforms found in a historical dig,
and support setting the clock to the PLL using the undocumented
device tree property.
Add some menuconfig so the codec can be selected and tested.
Signed-off-by: Linus Walleij <linusw@kernel.org>
Link: https://patch.msgid.link/20260409-asoc-uda1380-v3-1-b3d5a53f31be@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Create a kcontrol to enable or disable brown-out dynamically.
Signed-off-by: Jack Yu <jack.yu@realtek.com>
Link: https://patch.msgid.link/20260409060102.4177554-1-jack.yu@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Fix typo in comment where 'recieved' should be 'received'.
Signed-off-by: Qinghua Zhao <zqh1630@126.com>
Link: https://patch.msgid.link/20260409135213.16558-1-zqh1630@126.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Charles Keepax <ckeepax@opensource.cirrus.com> says:
Another round of SDCA fixes a couple of fix to the IRQ cleanup
from Richard, and a minor tweak to the IRQ handling from me.
|
|
In irq_enable_flags() and sdca_irq_disable() there is a NULL
check on the interrupt data pointer, however this is just pulled
from an array so can never be NULL. This was likely left over
from an earlier version that looked up the data in a different
way. Replace the check with checking for the IRQ itself being
non-zero.
Whilst here also drop the sdca_interrupt structure down into
the loop within the function to better match the style of the
rest of the code in this file.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20260409164328.3999434-4-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Fix inverted cleanup of the SoundWire IRQ and the function drivers
that use it.
The devm cleanup function to call sdca_dev_unregister_functions() was
being registered at the end of class_sdw_probe(). The bus core
creates the parent SoundWire IRQ handler after class_sdw_probe() has
returned, and it registers a devm cleanup handler at the same time.
This led to a cleanup inversion where the devm cleanup for the parent
Soundwire IRQ runs before the handler that removes the function drivers.
So the parent IRQ is destroyed before the function drivers had a chance
to do any cleanup and remove their IRQ handlers.
Move the registrations of the function driver cleanup into
class_boot_work() after the function drivers are registered, so that it
runs before the cleanup of the parent SoundWire IRQ handler.
Fixes: 2d877d0659cb ("ASoC: SDCA: Add basic SDCA class driver")
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20260409164328.3999434-3-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Fix typo of function argument name in the kernel doc.
Fixes: 0b8757b220f9 ("ASoC: SDCA: Unregister IRQ handlers on module remove")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202604090800.koxM6j6O-lkp@intel.com/
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20260409164328.3999434-2-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
alc269_resume() has an extra code to write GPIO data, but this is
basically already done in the standard alc_init(), hence it's
superfluous. Let's drop the code.
Since all external callers of alc_write_gpio_data() are gone after
this, fold the only usage of alc_write_gpio_data() into the caller and
drop the export as well.
Link: https://patch.msgid.link/20260409143735.1412134-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Feaulle Rainbow is a wired USB-C dynamic in-ear monitor (IEM) featuring
active noise cancellation (ANC).
The supported sample rates are 48000Hz and 96000Hz at 16bit or 24bit,
but it does not support reading the current sample rate and results in
an error message printed to kmsg. Set QUIRK_FLAG_GET_SAMPLE_RATE to skip
the sample rate check.
Its playback mixer reports val = -15360/0/128. Setting -15360 (-60dB)
mutes the playback, so QUIRK_FLAG_MIXER_PLAYBACK_MIN_MUTE is needed.
Add a quirk table entry matching VID/PID=0x0e0b/0xfa01 and applying
the mentioned quirk flags, so that it can work properly.
Quirky device sample:
usb 7-1: New USB device found, idVendor=0e0b, idProduct=fa01, bcdDevice= 1.00
usb 7-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 7-1: Product: Feaulle Rainbow
usb 7-1: Manufacturer: Generic
usb 7-1: SerialNumber: 20210726905926
Signed-off-by: Rong Zhang <i@rong.moe>
Link: https://patch.msgid.link/20260409-feaulle-rainbow-v1-1-09179e09000d@rong.moe
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Use the new GPIO helper function to clean up the open code.
Merely a code refactoring, and no behavior change.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20260409093826.1317626-11-tiwai@suse.de
|
|
Use the new GPIO helper function to clean up the open code.
Merely a code refactoring, and no behavior change.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20260409093826.1317626-10-tiwai@suse.de
|
|
Use the new GPIO helper function to clean up the open code.
Merely a code refactoring, and no behavior change.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20260409093826.1317626-9-tiwai@suse.de
|
|
Use the new GPIO helper function to clean up the open code.
Merely a code refactoring, and no behavior change.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20260409093826.1317626-8-tiwai@suse.de
|
|
Use the new GPIO helper function to clean up the open code.
Merely a code refactoring, and no behavior change.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20260409093826.1317626-7-tiwai@suse.de
|
|
So far we used the verb cache to restore the GPIO mask, direction and
data bits at PM resume. But, due to the nature of the cache resume
mechanism, the calling order isn't guaranteed, and this might lead to
some inconsistency at the restored state.
For assuring the GPIO verb orders, use the new GPIO helper function to
explicitly set up the GPIO bits, instead of using the codec verb
caches, while keeping the current data bits in ad198x_spec.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20260409093826.1317626-6-tiwai@suse.de
|
|
The previous implementation of the quirk for CSL Unity BF24B in commit
de65275fc94e ("ALSA: hda/realtek: Add quirk for CSL Unity BF24B")
introduced the unnecessary GPIO caching which leads to a superfluous
write at each init/resume.
Use the new helper to write GPIO bits directly for optimization.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20260409093826.1317626-5-tiwai@suse.de
|
|
Use a new helper function to clean up the code.
Along with it, make alc_write_gpio() static as well, which is used
only locally in realtek.c.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20260409093826.1317626-4-tiwai@suse.de
|
|
Introduce a common GPIO setup helper function, so that we can clean up
the open code found in many codec drivers later.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20260409093826.1317626-3-tiwai@suse.de
|
|
We used snd_hda_codec_read() for the verb write when a synchronization
is needed after the write, e.g. for the power state toggle or such
cases. It works in principle, but it looks rather confusing and too
hackish.
For improving the code readability, introduce a new helper function,
snd_hda_codec_write_sync(), which is another variant of
snd_hda_codec_write(), and replace the existing snd_hda_codec_read()
calls with this one.
No behavior change but just the code refactoring.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20260409093826.1317626-2-tiwai@suse.de
|
|
Setting up the interface when suspended/resumeing fail on this card.
Adding a reset and delay quirk will eliminate this problem.
usb 1-1: new full-speed USB device number 2 using xhci-hcd
usb 1-1: New USB device found, idVendor=12d1, idProduct=3a07
usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-1: Product: HUAWEI USB-C HEADSET
usb 1-1: Manufacturer: bestechnic
usb 1-1: SerialNumber: 0296C100000000000000000000000
Signed-off-by: Lianqin Hu <hulianqin@vivo.com>
Link: https://patch.msgid.link/TYUPR06MB62176A18EA7A9DD0AC2826BCD2582@TYUPR06MB6217.apcprd06.prod.outlook.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The msnd drivers do not implement system sleep callbacks today, so
they have no defined way to recover DSP state after suspend.
Add common card suspend/resume helpers, rerun the DSP
initialization path on resume, restore the cached capture-source
state, and rearm the shared IRQ for already-open users.
Signed-off-by: Cássio Gabriel <cassiogabrielcontato@gmail.com>
Link: https://patch.msgid.link/20260409-msnd-pm-support-v1-2-2abef720d0e7@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
System suspend cannot work for msnd today because the PCM trigger
paths reject SNDRV_PCM_TRIGGER_SUSPEND, and the driver has only
refcounted IRQ helpers.
Add the small helpers needed by the PM callbacks and restore master
volume from the cached ALSA mixer state when the DSP is
reinitialized.
Signed-off-by: Cássio Gabriel <cassiogabrielcontato@gmail.com>
Link: https://patch.msgid.link/20260409-msnd-pm-support-v1-1-2abef720d0e7@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
snd_akm4xxx_init() clears the register and volume caches before
dispatching by codec type. The AK5365 case then returns immediately,
leaving the software cache at zero instead of the documented AK5365
reset defaults.
The AK5365 capture volume controls read from volumes[] and the proc
register dump reads from images[], so the initial capture volume state
and proc output are wrong until a control write happens.
Seed the AK5365 cache with its documented reset defaults instead of
adding a guessed init sequence. The datasheet documents the reset
values and states that MCLK/LRCK changes do not require a PDN/PWN
reset because the chip has a built-in reset-free circuit.
Signed-off-by: Cássio Gabriel <cassiogabrielcontato@gmail.com>
Link: https://patch.msgid.link/20260408-ak5365-cache-defaults-v1-1-fff639aca3e3@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The CSL Unity BF24B all-in-one PC uses a Realtek ALC662 rev3 audio
codec and requires the correct GPIO configuration to enable sound
output from both the speakers and the headphone.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=221258
Signed-off-by: Zhang Heng <zhangheng@kylinos.cn>
Link: https://patch.msgid.link/20260409024028.1297587-1-zhangheng@kylinos.cn
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Pull 7.0-devel branch for further development of HD-audio codec quirks.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v7.0
A somewhat larger set of fixes than I'd like unfortunatey, not from any
one place but rather spread out over different drivers. We've got a
bunch more fixes for the SDCA interrupt support, several relatively
minor SOF fixes, a few more driver specific fixes and a couple more AMD
quirks.
|
|
By correlating devices with their names and IDs, the driver becomes more
discoverable.
Signed-off-by: Shenghao Ding <shenghao-ding@ti.com>
Link: https://patch.msgid.link/20260406103131.1883-1-shenghao-ding@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Replace DMI_EXACT_MATCH with DMI_MATCH for Lenovo SKU entries (21YW,
21YX) so the quirk applies to all variants of these models, not just
exact SKU matches.
Add ASOC_SDW_ACP_DMIC flag alongside ASOC_SDW_CODEC_SPKR in driver_data
for these Lenovo platform entries, as these platforms use ACP PDM DMIC
instead of SoundWire DMIC for digital microphone support.
Fixes: 3acf517e1ae0 ("ASoC: amd: amd_sdw: add machine driver quirk for Lenovo models")
Tested-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Reviewed-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Signed-off-by: Syed Saba Kareem <Syed.SabaKareem@amd.com>
Reviewed-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://patch.msgid.link/20260408133029.1368317-1-syed.sabakareem@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Ensure that all interrupt handlers are unregistered before the parent
regmap_irq is unregistered.
sdca_irq_cleanup() was only called from the component_remove(). If the
module was loaded and removed without ever being component probed the
FDL interrupts would not be unregistered and this would hit a WARN
when devm called regmap_del_irq_chip() during the removal of the
parent IRQ.
Fixes: 4e53116437e9 ("ASoC: SDCA: Fix errors in IRQ cleanup")
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20260408093835.2881486-5-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
According to the SDCA specification [1], when writing Function_Status during
handling this control, the value should mask off bit 7.
[1] MIPI Specification for SoundWire Device Class for Audio, version
1.1, section 7.14.1.3 (Host Software Handling of Function_Status)
Signed-off-by: Maciej Strozek <mstrozek@opensource.cirrus.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20260408093835.2881486-3-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
mask variable should not be overwritten within the for loop or it will
skip certain bits. Change to using BIT() macro.
Fixes: b9ab3b618241 ("ASoC: SDCA: Add some initial IRQ handlers")
Signed-off-by: Maciej Strozek <mstrozek@opensource.cirrus.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20260408093835.2881486-2-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
acp-da7219-max98357a() user exists behind it. No need to has pre-define.
Remove it. And it is local function, add static.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://patch.msgid.link/87h5pmvxfm.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The STM32 SAI driver do not set the clock strobing bit (CKSTR) for DSP_A,
DSP_B and LEFT_J formats, causing data to be sampled on the wrong BCLK
edge when SND_SOC_DAIFMT_NB_NF is used.
Per ALSA convention, NB_NF requires sampling on the rising BCLK edge.
The STM32MP25 SAI reference manual states that CKSTR=1 is required for
signals received by the SAI to be sampled on the SCK rising edge.
Without setting CKSTR=1, the SAI samples on the falling edge, violating
the NB_NF convention. For comparison, the NXP FSL SAI driver correctly
sets FSL_SAI_CR2_BCP for DSP_A, DSP_B and LEFT_J, consistent with its
I2S handling.
This patch adds SAI_XCR1_CKSTR for DSP_A, DSP_B and LEFT_J in
stm32_sai_set_dai_fmt which was verified empirically with a cs47l35 codec.
RIGHT_J (LSB) is not investigated and addressed by this patch.
Note: the STM32 I2S driver (stm32_i2s_set_dai_fmt) may have the same issue
for DSP_A mode, as I2S_CGFR_CKPOL is not set. This has not been verified
and is left for a separate investigation.
Signed-off-by: Tomasz Merta <tommerta@gmail.com>
Link: https://patch.msgid.link/20260408084056.20588-1-tommerta@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Intel ACE4 based products set more strict constraints on HDA BDLE start
address and length alignment. Add a constraint to align period size to
128 bytes.
The commit removes the "minimum as per HDA spec" comment. This comment
was misleading as spec actually does allow a 2 byte BDLE length, and
more importantly, period size also directly impacts how the BDLE start
addresses are aligned, so it is not sufficient just to consider allowed
buffer length.
Fixes: d3df422f66e8 ("ASoC: SOF: Intel: add initial support for NVL-S")
Cc: stable@vger.kernel.org
Reported-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Liam Girdwood <liam.r.girdwood@intel.com>
Link: https://patch.msgid.link/20260408084514.24325-3-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Intel ACE4 based products set more strict constraints on HDA BDLE start
address and length alignment. Modify capability flags to drop
AZX_DCAPS_NO_ALIGN_BUFSIZE for Intel Nova Lake platforms.
Fixes: 7f428282fde3 ("ALSA: hda: controllers: intel: add support for Nova Lake")
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Liam Girdwood <liam.r.girdwood@intel.com>
Cc: <stable@vger.kernel.org>
Link: https://patch.msgid.link/20260408084514.24325-2-peter.ujfalusi@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Currently, the driver only performs a hardware reset during the I2C probe
sequence. To ensure all internal states of the codec are properly cleared
without affecting the configuration registers, a software reset is also
required.
According to the hardware specification, writing to the Software Reset
register (R01) twice will reset all internal states safely.
This patch adds the nau8325_software_reset() function, executes it right
after the hardware reset in the probe function, and marks the R01 register
as writeable in the regmap configuration.
Signed-off-by: Neo Chang <YLCHANG2@nuvoton.com>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://patch.msgid.link/20260408052639.187149-1-YLCHANG2@nuvoton.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Fix sparse warning:
sound/usb/qcom/qc_audio_offload.c:943:27: sparse: incorrect type in argument 2
expected unsigned int val but got snd_pcm_format_t.
Explicitly cast pcm_format to unsigned int for snd_mask_leave().
Fixes: 326bbc348298 ("ALSA: usb-audio: qcom: Introduce QC USB SND offloading support")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202604062109.Oxi8JjWW-lkp@intel.com/
Signed-off-by: songxiebing <songxiebing@kylinos.cn>
Link: https://patch.msgid.link/20260408083311.774173-1-songxiebing@kylinos.cn
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Delta 410 uses snd_akm4xxx_reset() both around DFS changes and from
its PM callbacks, but the AK4529 case in this helper is still left
unimplemented and never drives the codec reset path.
The AK4529 datasheet documents register 09h.RSTN as an internal
timing reset. Clearing RSTN powers down the ADC and DAC blocks, but
does not reinitialize the register map. That matches the existing
ak4xxx helper model, which already keeps the desired codec state in
the software register cache.
Implement AK4529 reset handling by clearing 09h.RSTN on state == 1,
then replaying the cached register image and setting RSTN back to 1
on state == 0.
This restores cached Delta 410 mixer state after resume and gives
the AK4529 DFS-change path a real codec reset sequence.
Signed-off-by: Cássio Gabriel <cassiogabrielcontato@gmail.com>
Link: https://patch.msgid.link/20260407-ak4529-reset-handling-v1-1-b971c18b1a32@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
interwave still leaves both its ISA and PnP PM callbacks disabled even
though the shared GUS suspend and resume path now exists.
This board needs InterWave-specific glue around the shared GUS PM path.
The attached WSS codec has its own register image that must be saved and
restored across suspend, the InterWave-specific GF1 compatibility,
decode, MPU401, and emulation settings must be rewritten after the
shared GF1 resume path reinitializes the chip, and the probe-detected
InterWave memory layout must be restored without rerunning the
destructive DRAM/ROM detection path.
Track the optional STB TEA6330T bus at probe time, restore its cached
mixer state after resume, add resume-safe helpers for the InterWave
register and memory-configuration state, and wire both the ISA and PnP
front-ends up to the shared GUS PM helpers.
The resume path intentionally restores only the cached hardware setup.
It does not attempt to preserve sample RAM contents across suspend.
Signed-off-by: Cássio Gabriel <cassiogabrielcontato@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20260407-alsa-interwave-pm-v2-3-8dd96c6129e9@gmail.com
|
|
The InterWave STB variant uses a TEA6330T mixer on its private
I2C bus. The mixer state is cached in software, but there is no
helper to push that register image back to hardware after system
resume.
Add a small restore helper that reapplies the cached TEA6330T
register image to the device so board drivers can restore the
external mixer state as part of their PM resume path.
Take snd_i2c_lock() around the full device lookup and restore
sequence so the bus device list traversal is also protected.
Signed-off-by: Cássio Gabriel <cassiogabrielcontato@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20260407-alsa-interwave-pm-v2-2-8dd96c6129e9@gmail.com
|
|
Move the remaining standalone snd_tea6330t_detect() EXPORT_SYMBOL()
declaration next to its function definition so tea6330t.c follows the
usual layout.
No functional change intended.
Signed-off-by: Cássio Gabriel <cassiogabrielcontato@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20260407-alsa-interwave-pm-v2-1-8dd96c6129e9@gmail.com
|
