| Age | Commit message (Collapse) | Author |
|---|
|
The Hyper-V kernel-mode fcopy driver was removed in 6.10 and the new
fcopy daemon requires this uio driver to function. However, by
default the driver does not bind to any devices, and must be
configured through the sysfs "new_id" file.
Since the FCopy device is now only usable through this driver, add its
ID to the driver's ID table so that the daemon will work "out of the
box".
Signed-off-by: Ben Hutchings <benh@debian.org>
Fixes: ec314f61e4fc ("Drivers: hv: Remove fcopy driver")
Cc: stable <stable@kernel.org>
Link: https://patch.msgid.link/ahQ6xuhSReidmN-3@decadent.org.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Greg was not receiving patches for the GPIB subsystem from
folks using scripts/get_maintainer.pl -f drivers/gpib.
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Link: https://patch.msgid.link/20260630155517.5685-1-dpenkler@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into char-misc-linus
Dinh writes:
firmware: stratix10-svc: fixes for v7.2
- Fix a memory leak by explicitly using kfree() to match the list-managed lifetime
- Fix FCS SMC call documentation
- Add proper handling of a no response from the SDM
- Fix teardown order of service driver
* tag 'svc_fixes_for_v7.2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
firmware: stratix10-svc: fix teardown order in remove to prevent race
firmware: stratix10-svc: handle NO_RESPONSE in async poll
firmware: stratix10-svc: fix FCS SMC call kernel-doc
firmware: stratix10-svc: fix memory leaks and list corruption bugs
|
|
rtw_get_wps_ie() iterates over IE data from network frames without
validating that the IE header and payload fit within the remaining
buffer before reading them. Specifically:
- in_ie[cnt + 1] is read without checking cnt + 1 < in_len
- memcmp(&in_ie[cnt + 2], ...) accesses cnt + 2 without bounds check
- in_ie[cnt + 1] is used as length without verifying payload fits
Add bounds checks at the top of the loop body to break early if fewer
than 2 bytes remain for the IE header, or if the declared payload
extends past the end of the buffer. Also require at least 4 bytes of
payload before comparing the WPS OUI.
Fixes: 554c0a3abf21 ("staging: Add rtl8723bs sdio wifi driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Moksh Panicker <mokshpanicker.7@gmail.com>
Link: https://patch.msgid.link/20260625202911.26782-1-mokshpanicker.7@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
rtw_get_chan_type() maps the driver's channel offset to nl80211 channel
types the wrong way around.
In this driver HAL_PRIME_CHNL_OFFSET_LOWER means the primary channel is
the lower 20 MHz half of the 40 MHz pair, i.e. the secondary channel is
above the primary one: rtw_get_center_ch() computes the center channel
as "channel + 2" for OFFSET_LOWER, and bwmode_update_check() sets
OFFSET_LOWER when the AP's HT operation IE announces SCA (secondary
channel above). In nl80211 terms that is NL80211_CHAN_HT40PLUS, not
HT40MINUS.
Because of the inversion, cfg80211_rtw_get_channel() reports an HT40+
association as HT40-. For an HT40+ AP on a low channel (e.g. channel 3)
the resulting chandef spans below the 2.4 GHz band edge and is invalid,
so the regulatory core tears the connection down 60 seconds
(REG_ENFORCE_GRACE_MS) after the AP's country IE triggers a regdomain
change: reg_check_chans_work() considers the reported chandef unusable
and calls cfg80211_leave(). The supplicant then reconnects, the country
IE changes the regdomain again, and the cycle repeats, causing a
disconnect/reconnect loop every ~65 seconds for as long as the link is
up.
Observed on a TECLAST X80 Power tablet (RTL8723BS) associated to an
HT40+ AP on channel 3 with a KR country IE; a kprobe trace showed
cfg80211_disconnect() being invoked from reg_check_chans_work(). With
the mapping fixed, "iw dev wlan0 info" reports the correct
"width: 40 MHz, center1: 2432 MHz" and the periodic disconnects stop.
Fixes: 5402cc178c5d ("staging: rtl8723bs: add get_channel cfg80211 implementation")
Cc: stable@vger.kernel.org
Assisted-by: Claude-Code:claude-fable-5 bpftrace
Signed-off-by: MinJea Kim <qndkdrnl@gmail.com>
Link: https://patch.msgid.link/20260714131421.3980-1-qndkdrnl@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
On CONFIG_INET=n builds, mpls_valid_fib_dump_req() walks the parsed
attribute table itself instead of calling ip_valid_fib_dump_req(). The
RTA_OIF arm passes tb[RTA_OIF] to nla_get_u32() without checking it is
present, so an RTM_GETROUTE dump for AF_MPLS with strict checking and no
RTA_OIF hits a NULL dereference.
RTM_GETROUTE is RTNL_KIND_GET, which rtnetlink_rcv_msg() permits without
CAP_NET_ADMIN, so an unprivileged user can trigger it.
Oops: general protection fault, probably for non-canonical address
0xdffffc0000000000: 0000 [#1] SMP KASAN NOPTI
KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
RIP: 0010:mpls_valid_fib_dump_req (net/mpls/af_mpls.c:2189)
Call Trace:
mpls_dump_routes (net/mpls/af_mpls.c:2236)
netlink_dump (net/netlink/af_netlink.c:2331)
__netlink_dump_start (net/netlink/af_netlink.c:2446)
rtnetlink_rcv_msg (net/core/rtnetlink.c:7033)
netlink_rcv_skb (net/netlink/af_netlink.c:2556)
netlink_unicast (net/netlink/af_netlink.c:1345)
netlink_sendmsg (net/netlink/af_netlink.c:1900)
__sock_sendmsg (net/socket.c:790)
____sys_sendmsg (net/socket.c:2684)
___sys_sendmsg (net/socket.c:2738)
__sys_sendmsg (net/socket.c:2770)
do_syscall_64 (arch/x86/entry/syscall_64.c:94)
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:121)
Skip unset attributes, as ip_valid_fib_dump_req() does.
Fixes: 196cfebf8972 ("net/mpls: Handle kernel side filtering of route dumps")
Assisted-by: Claude:claude-opus-4-8
Reported-by: Xiang Mei <xmei5@asu.edu>
Signed-off-by: Weiming Shi <bestswngs@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://patch.msgid.link/20260711114958.1009619-3-bestswngs@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
llc_sap_add_socket() takes a SAP reference for each socket added to a SAP,
and llc_sap_remove_socket() releases it. llc_create_incoming_sock() takes
an additional SAP reference after adding the child socket.
This extra reference was balanced by an explicit llc_sap_put() in
llc_ui_release() until commit 3100aa9d74db ("llc: fix SAP reference
counting w.r.t. socket handling") removed that put. The corresponding hold
in the accept path was left behind.
When such a child socket is removed, only the reference taken by
llc_sap_add_socket() is released. The extra reference keeps the SAP alive
after its last socket is removed. Remove the obsolete hold.
Fixes: 3100aa9d74db ("llc: fix SAP reference counting w.r.t. socket handling")
Cc: stable@vger.kernel.org
Signed-off-by: Xuanqiang Luo <luoxuanqiang@kylinos.cn>
Link: https://patch.msgid.link/20260712130343.518797-1-xuanqiang.luo@linux.dev
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The "mac" bind mode reactivation downs the interface, restores the saved
MAC and renames it to trigger a target resume. This assumes the recreated
interface comes back with a different MAC, which is true under
MACAddressPolicy=none (as on the Netdev CI) but not when MACs are
persistent. In the persistent case netconsole resumes the target on its
own, and the down/restore/rename flow instead drops it and fails the test.
Guard the block on the MAC having actually changed so the test passes
under both policies.
Fixes: 6ecc08329bab ("selftests: netconsole: validate target resume")
Reported-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Closes: https://lore.kernel.org/netdev/f398373e-2cb4-4649-a491-9763df94d98b@kernel.org/
Signed-off-by: Andre Carvalho <asantostc@gmail.com>
Tested-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Reviewed-by: Breno Leitao <leitao@debian.org>
Link: https://patch.msgid.link/20260710-netcons-mac-reload-v1-1-3fb1bcc70b4a@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
It's strongly recommended for GPIO drivers to always implement the
.get_direction() callback - even when the direction is tracked in
software. The GPIO core emits a warning when the callback is missing
and a user reads the direction of a line, e.g. via
/sys/kernel/debug/gpio.
Fixes: dfeae619d781 ("serial: sc16is7xx")
Cc: stable <stable@kernel.org>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Link: https://patch.msgid.link/20260716210813.2582826-1-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
platforms
Commit b1b4efea05a5 ("serial: 8250_mid: Disable DMA for selected
platforms") replaced the dnv_board setup and exit callbacks with
PTR_IF(false, ...), which evaluates to NULL. However, the three call
sites in mid8250_probe() and mid8250_remove() unconditionally
dereference these function pointers without NULL checks, causing a NULL
pointer dereference (kernel oops) on any Denverton (DNV), Ice Lake Xeon
D (ICX-D/CDF), or Snowridge (SNR) platform.
Fix this by adding the missing NULL checks before calling the setup and
exit callbacks.
Fixes: b1b4efea05a5 ("serial: 8250_mid: Disable DMA for selected platforms")
Cc: stable <stable@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jiangshan Yi <yijiangshan@kylinos.cn>
Link: https://patch.msgid.link/20260715073546.1875083-1-yijiangshan@kylinos.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
bnxt_aux_devices_init() calls auxiliary_device_init() before all fields
used by bnxt_aux_dev_release() are initialized. After
auxiliary_device_init() succeeds, later errors must unwind with
auxiliary_device_uninit(), which invokes the release callback.
The release callback assumes that aux_priv->id, aux_priv->edev,
edev->net and edev->ulp_tbl are all populated. If allocation fails
after auxiliary_device_init(), the release path can otherwise dereference
or clear partially initialized state.
Allocate and attach the bnxt_en_dev and ULP table before calling
auxiliary_device_init(), so the release callback only sees a fully
initialized auxiliary private object. If auxiliary_device_init() itself
fails, free those allocations directly because device_initialize() has not
run and the release callback will not be invoked.
This issue was found by a static analysis checker and confirmed by manual
source review.
Fixes: 194fad5b2781 ("bnxt_en: Refactor bnxt_rdma_aux_device_init/uninit functions")
Signed-off-by: Ruoyu Wang <ruoyuw560@gmail.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Link: https://patch.msgid.link/20260711163716.3996929-1-ruoyuw560@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
uea_probe() distinguishes a pre-firmware device from a post-firmware one
using the USB id (UEA_IS_PREFIRM()), and stores a different object as the
interface data in each case: a 'struct completion' for a pre-firmware
device (to be waited on in .disconnect()), or a 'struct usbatm_data' for a
post-firmware one.
uea_disconnect() instead tells the two apart by the number of interfaces
of the active configuration (a pre-firmware device exposes a single
interface, ADI930 has 2 and eagle has 3), and casts the interface data
accordingly.
Because the two handlers use different criteria, a crafted device that
advertises a pre-firmware id together with a multi-interface descriptor
(or a post-firmware id with a single interface) makes them disagree: the
small 'struct completion' stored by uea_probe() is then passed to
usbatm_usb_disconnect(), which casts it to 'struct usbatm_data' and takes
instance->serialize, reading past the end of the allocation:
BUG: KASAN: slab-out-of-bounds in __mutex_lock+0x152a/0x1b80
Read of size 8 at addr ffff8880470e2c60 by task kworker/1:2/982
...
__mutex_lock+0x152a/0x1b80
usbatm_usb_disconnect+0x70/0x820
uea_disconnect+0x133/0x2c0
usb_unbind_interface+0x1dd/0x9e0
...
which belongs to the cache kmalloc-96 of size 96
The buggy address is located 0 bytes to the right of
allocated 96-byte region [ffff8880470e2c00, ffff8880470e2c60)
Reject such inconsistent descriptors in uea_probe() so that both handlers
always make the same pre/post-firmware decision.
Reported-by: syzbot+e62a973f8322b3bbe3ac@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=e62a973f8322b3bbe3ac
Fixes: e2674dfbed8a ("usb: atm: ueagle-atm: wait for pre-firmware load in .disconnect()")
Signed-off-by: Diego Fernando Mancera Gomez <diegomancera.dev@gmail.com>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Link: https://patch.msgid.link/20260717080704.1264-1-diegomancera.dev@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The auth_hmacs array in struct sctp_cookie is supposed to store a complete
SCTP_AUTH_HMAC_ALGO parameter, which consists of a struct sctp_paramhdr
followed by N HMAC identifiers.
However, the array size was calculated using an extra 2 bytes instead of
sizeof(struct sctp_paramhdr), which is 4 bytes. When four HMAC identifiers
are configured, the HMAC-ALGO parameter stored in the endpoint is larger
than the auth_hmacs buffer in the cookie.
As a result, sctp_association_init() copies beyond the end of auth_hmacs
when initializing the association, corrupting the adjacent auth_chunks
field. This can lead to an invalid HMAC identifier being accepted and later
cause an out-of-bounds read in sctp_auth_get_hmac().
Fix the array size calculation by including the full SCTP parameter header
size.
Fixes: 1f485649f529 ("[SCTP]: Implement SCTP-AUTH internals")
Reported-by: Yuan Tan <yuantan098@gmail.com>
Reported-by: Xin Liu <dstsmallbird@foxmail.com>
Reported-by: Zihan Xi <xizh2024@lzu.edu.cn>
Reported-by: Ren Wei <enjou1224z@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Link: https://patch.msgid.link/634a0de0d5de29532915e6d47c92a0cbc206e03f.1783707155.git.lucien.xin@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Fix a race-condition use-after-free in tunnel_key_release_params().
The function releases the metadata_dst of the old params synchronously
via dst_release() while deferring the params struct free with
kfree_rcu(). A concurrent tunnel_key_act() reader on the datapath may
still hold the old params pointer (under rcu_read_lock_bh) and proceed
to call dst_clone(¶ms->tcft_enc_metadata->dst) after the writer's
dst_release has already pushed the dst's rcuref to RCUREF_DEAD.
zdi-disclosures@trendmicro.com produced a poc which i (and Victor) verified
that KASAN reports:
==================================================================
BUG: KASAN: slab-use-after-free in instrument_atomic_read_write include/linux/instrumented.h:112
BUG: KASAN: slab-use-after-free in atomic_sub_return_release include/linux/atomic/atomic-instrumented.h:326
BUG: KASAN: slab-use-after-free in __rcuref_put include/linux/rcuref.h:109
BUG: KASAN: slab-use-after-free in rcuref_put include/linux/rcuref.h:173
BUG: KASAN: slab-use-after-free in dst_release+0x5b/0x370 net/core/dst.c:168
Write of size 4 at addr ffff88806158de40 by task poc/9388
CPU: 0 UID: 0 PID: 9388 Comm: poc Tainted: G W 7.1.0-rc7 #7 PREEMPT(lazy)
Tainted: [W]=WARN
Hardware name: QEMU Ubuntu 25.10 PC v2 (i440FX + PIIX, + 10.1 machine, 1996), BIOS 1.16.3-debian-1.16.3-2 04/01/2014
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:94
dump_stack_lvl+0x100/0x190 lib/dump_stack.c:120
print_address_description mm/kasan/report.c:378
print_report+0x139/0x4ad mm/kasan/report.c:482
kasan_report+0xe4/0x1d0 mm/kasan/report.c:595
check_region_inline mm/kasan/generic.c:186
kasan_check_range+0x125/0x200 mm/kasan/generic.c:200
instrument_atomic_read_write include/linux/instrumented.h:112
atomic_sub_return_release include/linux/atomic/atomic-instrumented.h:326
__rcuref_put include/linux/rcuref.h:109
rcuref_put include/linux/rcuref.h:173
dst_release+0x5b/0x370 net/core/dst.c:168
refdst_drop include/net/dst.h:272
skb_dst_drop include/net/dst.h:284
skb_release_head_state+0x293/0x400 net/core/skbuff.c:1163
skb_release_all net/core/skbuff.c:1187
[..]
Allocated by task 9391:
kasan_save_stack+0x30/0x50 mm/kasan/common.c:57
kasan_save_track+0x14/0x30 mm/kasan/common.c:78
poison_kmalloc_redzone mm/kasan/common.c:398
__kasan_kmalloc+0x9a/0xb0 mm/kasan/common.c:415
kasan_kmalloc include/linux/kasan.h:263
__do_kmalloc_node mm/slub.c:5296
__kmalloc_noprof+0x2f1/0x830 mm/slub.c:5308
kmalloc_noprof include/linux/slab.h:954
kzalloc_noprof include/linux/slab.h:1188
offload_action_alloc+0x2f/0x130 net/core/flow_offload.c:35
tcf_action_offload_add_ex+0x1ba/0x880 net/sched/act_api.c:258
tcf_action_offload_add net/sched/act_api.c:293
tcf_action_init+0x66e/0xa20 net/sched/act_api.c:1547
tcf_action_add+0xf6/0x5d0 net/sched/act_api.c:2101
[..]
Freed by task 9391:
kasan_save_stack+0x30/0x50 mm/kasan/common.c:57
kasan_save_track+0x14/0x30 mm/kasan/common.c:78
kasan_save_free_info+0x3b/0x70 mm/kasan/generic.c:584
poison_slab_object mm/kasan/common.c:253
__kasan_slab_free+0x6b/0x90 mm/kasan/common.c:285
kasan_slab_free include/linux/kasan.h:235
slab_free_hook mm/slub.c:2689
slab_free mm/slub.c:6251
kfree+0x21f/0x6b0 mm/slub.c:6566
tcf_action_offload_add_ex+0x4ad/0x880 net/sched/act_api.c:284
tcf_action_offload_add net/sched/act_api.c:293
tcf_action_init+0x66e/0xa20 net/sched/act_api.c:1547
tcf_action_add+0xf6/0x5d0 net/sched/act_api.c:2101
The buggy address belongs to the object at ffff88806158de00
which belongs to the cache kmalloc-256 of size 256
The buggy address is located 64 bytes inside of
freed 256-byte region [ffff88806158de00, ffff88806158df00)
The buggy address belongs to the physical page:
page: refcount:0 mapcount:0 mapping:0000000000000000 index:0xffff88806158d600 pfn:0x6158c
head: order:1 mapcount:0 entire_mapcount:0 nr_pages_mapped:0 pincount:0
flags: 0x4fff00000000240(workingset|head|node=1|zone=1|lastcpupid=0x7ff)
page_type: f5(slab)
raw: 04fff00000000240 ffff88801c841b40 ffffea0001856290 ffffea0001856190
raw: ffff88806158d600 0000000800100009 00000000f5000000 0000000000000000
head: 04fff00000000240 ffff88801c841b40 ffffea0001856290 ffffea0001856190
head: ffff88806158d600 0000000800100009 00000000f5000000 0000000000000000
head: 04fff00000000001 ffffffffffffff81 00000000ffffffff 00000000ffffffff
head: ffffffffffffffff 0000000000000000 00000000ffffffff 0000000000000002
page dumped because: kasan: bad access detected
page_owner tracks the page as allocated
page last allocated via order 1, migratetype Unmovable, gfp_mask 0xd2820(GFP_ATOMIC|__GFP_NOWARN|__GFP_NORETRY|__GFP_COMP|__GFP_NOMEMALLOC), pid 9391, tgid 9378 (poc), ts 123227323196, free_ts 0
set_page_owner include/linux/page_owner.h:32
post_alloc_hook+0xfe/0x140 mm/page_alloc.c:1853
prep_new_page mm/page_alloc.c:1861
get_page_from_freelist+0x110c/0x2fc0 mm/page_alloc.c:3941
__alloc_frozen_pages_noprof+0x263/0x2bc0 mm/page_alloc.c:5221
alloc_slab_page mm/slub.c:3278
allocate_slab mm/slub.c:3467
new_slab+0xa6/0x690 mm/slub.c:3525
refill_objects+0x271/0x420 mm/slub.c:7272
refill_sheaf mm/slub.c:2816
__pcs_replace_empty_main+0x373/0x630 mm/slub.c:4652
alloc_from_pcs mm/slub.c:4750
slab_alloc_node mm/slub.c:4884
__do_kmalloc_node mm/slub.c:5295
__kmalloc_noprof+0x66d/0x830 mm/slub.c:5308
kmalloc_noprof include/linux/slab.h:954
metadata_dst_alloc+0x26/0x90 net/core/dst.c:298
tun_rx_dst include/net/dst_metadata.h:144
__ip_tun_set_dst include/net/dst_metadata.h:208
tunnel_key_init+0xb01/0x1b90 net/sched/act_tunnel_key.c:451
tcf_action_init_1+0x46b/0x6c0 net/sched/act_api.c:1428
tcf_action_init+0x448/0xa20 net/sched/act_api.c:1503
tcf_action_add+0xf6/0x5d0 net/sched/act_api.c:2101
[..]
==================================================================
Fix by moving dst_release() into a custom RCU callback that runs
after the grace period, matching the lifetime of the containing
params struct. Readers in the datapath therefore always find a live
rcuref when calling dst_clone().
Fixes: 9174c3df1cd18 ("net/sched: act_tunnel_key: fix memory leak in case of action replace")
Reported-by: zdi-disclosures@trendmicro.com
Tested-by: Victor Nogueira <victor@mojatatu.com>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Davide Caratti <dcaratti@redhat.com>
Link: https://patch.msgid.link/20260711150537.7946-1-jhs@mojatatu.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When a dpll_pin is shared across multiple dpll_device instances and
those devices are being unregistered (e.g. during driver module removal),
a NULL pointer dereference can occur in dpll_msg_add_pin_ref_sync().
This happens under the following conditions:
- A pin is registered with two or more dpll devices (dpll_A, dpll_B)
- The pin has ref_sync pairs with other pins
- During unregistration of dpll_A's pins, a ref_sync partner pin is
unregistered first, removing it from dpll_A->pin_refs
- But since the partner pin is still registered with dpll_B, its
dpll_refs is not empty, so dpll_pin_ref_sync_pair_del() does NOT
run and the partner stays in the pin's ref_sync_pins xarray
- When the pin itself is then unregistered from dpll_A, the delete
notification calls dpll_msg_add_pin_ref_sync() which finds the
partner in ref_sync_pins, passes dpll_pin_available() (partner is
still registered with dpll_B), but dpll_pin_on_dpll_priv(dpll_A,
partner) returns NULL because partner was already removed from
dpll_A->pin_refs
- The NULL priv pointer is passed to the driver's ref_sync_get
callback, which dereferences it
BUG: kernel NULL pointer dereference, address: 0000000000000034
Oops: Oops: 0000 [#1] SMP NOPTI
RIP: 0010:zl3073x_dpll_input_pin_ref_sync_get+0x73/0x80 [zl3073x]
Call Trace:
dpll_msg_add_pin_ref_sync+0xb8/0x200
dpll_cmd_pin_get_one+0x3b6/0x4b0
dpll_pin_event_send+0x72/0x140
__dpll_pin_unregister+0x5a/0x2b0
dpll_pin_unregister+0x49/0x70
Fix this by skipping ref_sync pins whose priv pointer cannot be resolved
for the current dpll device.
Fixes: 58256a26bfb3 ("dpll: add reference sync get/set")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://patch.msgid.link/20260710193625.1378822-1-ivecera@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Release the TIME_WAIT socket reference and jump to discard_it
upon PSP policy failure in both IPv4 and IPv6 receive paths.
This prevents a memory leak of tcp_tw_bucket structures.
Fixes: 659a2899a57d ("tcp: add datapath logic for PSP with inline key exchange")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@google.com>
Reviewed-by: Daniel Zahka <daniel.zahka@gmail.com>
Link: https://patch.msgid.link/20260710181317.4060230-1-edumazet@google.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Workloads that repeatedly allocate and release mkeys carrying TPH
steering-tag hints (e.g. churning RDMA MRs) leak one
struct mlx5_st_idx_data per cycle; kmemleak flags it as unreferenced
and the kmalloc slab grows over time.
When the last reference to an ST table entry is dropped,
mlx5_st_dealloc_index() removed the entry from idx_xa but the backing
mlx5_st_idx_data allocation was never freed.
Free idx_data after the xa_erase() so the lifetime of the bookkeeping
struct matches the lifetime of the ST entry it tracks.
Cc: stable@vger.kernel.org
Fixes: 888a7776f4fb ("net/mlx5: Add support for device steering tag")
Reviewed-by: Michael Gur <michaelgur@nvidia.com>
Signed-off-by: Zhiping Zhang <zhipingz@meta.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20260702222507.1234467-1-zhipingz@meta.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2026-07-16
this is a pull request of 19 patches for net/main.
The first patch is by Alexander Hölzl and fixes the Kconfig
description of the vxcan driver.
Next patch by Fan Wu fixes the tear down order in the esd_usb driver.
Followed by a patch by Oliver Hartkopp that adds missing locking for
the raw flags in the CAN_RAW protocol.
Shuhao Fu's patch for the j1939 protocol fix lockless
local-destination check.
Stéphane Grosjean updates their email address.
The next 11 patches all target the CAM Broadcast Manager protocol. One
contributed by Lee Jones the remaining ones by Oliver Hartkopp. They
fix several concurrency and locking issues found by various bots.
The last 3 patches are also by Oliver Hartkopp fixing concurrency and
locking issues found by various bots in the CAN ISO Transport
Protocol.
linux-can-fixes-for-7.2-20260716
* tag 'linux-can-fixes-for-7.2-20260716' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
can: isotp: serialize TX state transitions under so->rx_lock
can: isotp: fix use-after-free race with concurrent NETDEV_UNREGISTER
can: isotp: use unconditional synchronize_rcu() in isotp_release()
can: bcm: track a single source interface for ANYDEV timeout/throttle ops
can: bcm: fix data race on rx_stamp/rx_ifindex in bcm_rx_handler()
can: bcm: fix stale rx/tx ops after device removal
can: bcm: add missing device refcount for CAN filter removal
can: bcm: validate frame length in bcm_rx_setup() for RTR replies
can: bcm: extend bcm_tx_lock usage for data and timer updates
can: bcm: add missing rcu list annotations and operations
can: bcm: fix CAN frame rx/tx statistics
can: bcm: add locking when updating filter and timer values
can: bcm: fix lockless bound/ifindex race and silent RX_SETUP failure
can: bcm: defer rx_op deallocation to workqueue to fix thrtimer UAF
can: peak: Modification of references to email accounts being deleted
can: j1939: fix lockless local-destination check
can: raw: add locking for raw flags bitfield
can: esd_usb: kill anchored URBs before freeing netdevs
can: vxcan: Kconfig: fix description stating no local echo provided
====================
Link: https://patch.msgid.link/20260716155528.809908-1-mkl@pengutronix.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth
Luiz Augusto von Dentz says:
====================
bluetooth pull request for net:
- hci_sync: hold hdev->lock for hci_conn_params lookups
- hci_sync: extend conn_hash lookup critical sections
- hci_qca: Clear memdump state on invalid dump size
- MGMT: revalidate LOAD_CONN_PARAM queued update
- MGMT: Translate HCI reason in Device Disconnected event
- MGMT: fix locking in unpair_device/disconnect_sync
- MGMT: hold reference for hci_conn in mgmt_pending_cmds
- btrtl: validate firmware patch bounds
- qca: fix NVM tag length underflow in TLV parser
* tag 'for-net-2026-07-13' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth:
Bluetooth: mgmt: Translate HCI reason in Device Disconnected event
Bluetooth: hci_qca: Clear memdump state on invalid dump size
Bluetooth: hci_sync: hold hdev->lock for hci_conn_params lookups
Bluetooth: mgmt: hold reference for hci_conn in mgmt_pending_cmds
Bluetooth: mgmt: fix locking in unpair_device/disconnect_sync
Bluetooth: hci_sync: extend conn_hash lookup critical sections
Bluetooth: btrtl: validate firmware patch bounds
Bluetooth: MGMT: revalidate LOAD_CONN_PARAM queued update
Bluetooth: qca: fix NVM tag length underflow in TLV parser
====================
Link: https://patch.msgid.link/20260713141940.954317-1-luiz.dentz@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf
Florian Westphal says:
====================
netfilter: updates for net
The following patchset contains Netfilter fixes for *net*.
These are fixes for bugs except patches 6 and 9 which fix issues added in
last PR and 7.1-rc1.
1) Reject unsupported target families in xt_nat_checkentry().
From Wyatt Feng.
2) Fix inverted time_after() check in ecache_work_evict_list().
Causes pointless work rescheds and thus way longer time to
clear the pending event backlog. From Yizhou Zhao.
3) Fix a use-after-free in br_ip6_fragment() caused by a dangling prevhdr
pointer. From Xiang Mei.
4) Fix incorrect conntrack zone comparison in nf_conncount tuple
deduplication. Pass IP_CT_DIR_ORIGINAL, not zone direction.
From Yizhou Zhao.
5) Add bridge tunnel flowtable regression test for a bug that
got fixed in the previous PR. From Zhengyang Chen.
6) Use the correct direction when setting up tunnel routes in the flowtable
xmit path. From Pablo Neira Ayuso. This fixes a bug added in the
previous PR.
7) Reload IP header after potential skb head reallocation in IPVS.
8) Fix incorrect IPv6 transport offsets in TCP application code. Correct the
ICMPv6 header offset to ensure proper checksumming with extension headers,
from Julian Anastasov. this is a followup to the previous PR.
9) Remove null-termination requirement for xt_physdev masks, this broke
device names with 15 characters.
netfilter pull request nf-26-07-10
* tag 'nf-26-07-10' of https://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
netfilter: xt_physdev: masks are not c-strings
ipvs: fix more places with wrong ipv6 transport offsets
ipvs: reload ip header after head reallocation
netfilter: flowtable: use correct direction to set up tunnel route
selftests: netfilter: add bridge tunnel flowtable regression
netfilter: nf_conncount: fix zone comparison in tuple dedup
netfilter: bridge: fix stale prevhdr pointer in br_ip6_fragment()
netfilter: ecache: fix inverted time_after() check
netfilter: xt_nat: reject unsupported target families
====================
Link: https://patch.msgid.link/20260710143733.29741-1-fw@strlen.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v7.2
A fairly standard collection of device specific fixes and quirks,
nothing particularly remarkable.
|
|
amdxdna_cmd_submit() stores current->mm in job->mm without holding any
reference. aie2_sched_job_run() later access job->mm from the DRM
scheduler worker thread. With only a raw pointer and no structural
reference, the mm_struct can be freed before the scheduler runs the job.
Fix this by calling mmgrab() to hold a structural mm_count reference for
the lifetime of the job, paired with mmdrop() in every cleanup path.
Fixes: aac243092b70 ("accel/amdxdna: Add command execution")
Reviewed-by: Max Zhen <max.zhen@amd.com>
Signed-off-by: Lizhi Hou <lizhi.hou@amd.com>
Link: https://patch.msgid.link/20260716151305.1595780-1-lizhi.hou@amd.com
|
|
Pull smb client fixes from Steve French:
- fallocate fixes
- unit test fixes
- fix allocation size after duplicate extents
- fix check for overlapping data areas
* tag 'v7.2-rc3-smb3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6:
smb/client: flush dirty data before punching a hole
smb/client: Use EXPORT_SYMBOL_IF_KUNIT() to export symbols in SMB2
smb/client: Use EXPORT_SYMBOL_IF_KUNIT() to export symbols
smb: client: reject overlapping data areas in SMB2 responses
smb/client: refresh allocation after EOF-extending fallocate
smb/client: emulate small EOF-extending mode 0 fallocate ranges
smb/client: reduce fallocate zero buffer allocation
smb/client: handle overlapping allocated ranges in fallocate
smb/client: refresh allocation size after duplicate extents
smb: client: use kvzalloc() for megabyte buffer in simple fallocate
|
|
Ihor Solodrai says:
====================
bpf: Fix tracing of kfuncs with implicit args
Tejun reported an issue where a BPF program tracing a kfunc with
KF_IMPLICIT_ARGS can crash the kernel [1]. This is caused by a bug in
bpf_check_attach_target(): the btf_func_model for such a kfunc is
computed from a wrong BTF prototype. For more details see the commit
message of patch #1.
The second patch adds a selftest that can catch this situation.
The fix is a candidate for 7.1 backport.
[1] https://github.com/sched-ext/scx/issues/3687#issuecomment-4906694106
---
v2->v3:
* Replace btf_kfunc_accumulated_flags() with btf_kfunc_check_flag()
following a discussion with Eduard. Inlining the hook walk is a
worse option than a helper, because BTF_KFUNC_HOOK_MAX and co are
internal to btf.c and exposing them is uglier.
* remove reduntant btf_is_func check (Jiri)
* formatting nit (Eduard)
v2: https://lore.kernel.org/bpf/20260710192940.3020280-1-ihor.solodrai@linux.dev/
v1->v2:
* Take a module reference in btf_attach_func_proto() around the
btf_kfunc_accumulated_flags() call (sashiko)
v1: https://lore.kernel.org/bpf/20260710005902.2234832-1-ihor.solodrai@linux.dev/
---
====================
Link: https://patch.msgid.link/20260713235223.1639022-1-ihor.solodrai@linux.dev
Signed-off-by: Eduard Zingerman <eddyz87@gmail.com>
|
|
KF_IMPLICIT_ARGS kfuncs have a BPF-call prototype and a real kernel
target prototype. Add a tracing selftest that attaches fentry and fexit
programs to bpf_kfunc_implicit_arg(), runs a syscall BPF program that
calls it, and checks that the tracing context exposes both the explicit
argument and the implicit prog aux pointer.
Co-developed-by: Ihor Solodrai <ihor.solodrai@linux.dev>
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Signed-off-by: Ihor Solodrai <ihor.solodrai@linux.dev>
Link: https://patch.msgid.link/20260713235223.1639022-3-ihor.solodrai@linux.dev
Signed-off-by: Eduard Zingerman <eddyz87@gmail.com>
|
|
A kfunc marked with KF_IMPLICIT_ARGS flag takes implicit arguments
(such as bpf_prog_aux) that the verifier injects at load time.
resolve_btfids strips those from the kfunc's BTF-visible prototype and
keeps the real kernel ABI in a counterpart _impl prototype [1].
fentry/fexit/fmod_ret/fsession programs may attach to the BPF kernel
functions, including those with implicit args. However
bpf_check_attach_target() and bpf_check_attach_btf_id_multi() extract
the struct btf_func_model from the wrong BTF prototype of the
kfunc. The btf_func_model is later read to construct the trampoline,
which then causes the injected implicit argument to be clobbered and
the kfunc dereferencing garbage.
Add btf_attach_func_proto() to resolve the real ABI prototype of the
kfunc the way the call site does: by looking up the _impl prototype
for a KF_IMPLICIT_ARGS kfunc. Use it at both attach-target model
construction sites.
To enable this, make two supporting changes:
* pass bpf_verifier_log instead of bpf_verifier_env to
find_kfunc_impl_proto(), so it can be reused from the attach path
* add btf_kfunc_check_flag() to test a flag across all of a kfunc's
hook sets, because a program attaching to a kfunc is not in the
kfunc's call-set
KF_IMPLICIT_ARGS must be consistent across the sets, so
btf_kfunc_check_flag() returns -EINVAL on inconsistency.
btf_kfunc_check_flag() reads the kfunc's flags from the target's
kfunc_set_tab. For a module BTF that table is stable only after the
module is live, so take a module reference around the read, mirroring
how the kfunc call path gates the same lookup with btf_try_get_module().
The remaining call sites of btf_distill_func_proto() are safe as
is. The BPF_TRACE_ITER case distills a registered iterator's
prototype, and bpf_struct_ops_desc_init() distills the
function-pointer members of a struct_ops type. Neither is a kfunc, and
so can't have implicit arguments.
[1] https://lore.kernel.org/all/20260120222638.3976562-1-ihor.solodrai@linux.dev/
Fixes: 64e1360524b9 ("bpf: Verifier support for KF_IMPLICIT_ARGS")
Reported-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Ihor Solodrai <ihor.solodrai@linux.dev>
Link: https://github.com/sched-ext/scx/issues/3687#issuecomment-4906694106
Link: https://patch.msgid.link/20260713235223.1639022-2-ihor.solodrai@linux.dev
Signed-off-by: Eduard Zingerman <eddyz87@gmail.com>
|
|
rhashtable_walk_start_check() has two restart paths when resuming a walk.
When iter->walker.tbl is valid, it re-validates iter->p against the table
and sets iter->p = NULL if the object is gone. When iter->walker.tbl is
NULL (table was freed during resize), it resets slot and skip but forgets
to clear iter->p.
rhashtable_walk_next() then dereferences the stale iter->p, reading
freed memory. This is a use-after-free.
Any caller that does multi-fragment rhashtable walks across
walk_stop/walk_start boundaries is affected. Concrete cases include
netlink_diag (__netlink_diag_dump in net/netlink/diag.c) and TIPC
(tipc_nl_sk_walk in net/tipc/socket.c).
Crash stack (netlink_diag):
BUG: KASAN: slab-use-after-free in rhashtable_walk_next+0x365/0x3c0
Read of size 8 at addr ffff88801a9d2438 (freed kmalloc-2k, offset 1080)
Call Trace:
rhashtable_walk_next+0x365/0x3c0 (lib/rhashtable.c:1016)
__netlink_diag_dump+0x160/0x760 (net/netlink/diag.c:122)
netlink_diag_dump+0xc2/0x240
netlink_dump+0x5bc/0x1270
netlink_recvmsg+0x7a3/0x980
sock_recvmsg+0x1bc/0x200
__sys_recvfrom+0x1d4/0x2c0
Fixes: 5d240a8936f6 ("rhashtable: improve rhashtable_walk stability when stop/start used.")
Cc: <stable@vger.kernel.org>
Reported-by: AutonomousCodeSecurity@microsoft.com
Reported-by: Yuan Tan <yuantan098@gmail.com>
Closes: https://lore.kernel.org/linux-crypto/CAB8m9Wh559e+=n8z51gB8DrbEyCc2mc0MgGjrRR6_VXBmU=2AQ@mail.gmail.com
Signed-off-by: Cen Zhang (Microsoft) <blbllhy@gmail.com>
Reviewed-by: NeilBrown <neil@brown.name>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
These macros are used like expressions, so they should not emit a
semicolon. This is being turned into a hard error in a future release of
Rust.
error: trailing semicolon in macro used in expression position
--> drivers/gpu/nova-core/firmware/fsp.rs:79:34
|
79 | .inspect_err(|_| dev_err!(dev, "FMC firmware missing '{}' section\n", name))
| ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
|
= warning: this was previously accepted by the compiler but is being phased out; it will become a hard error in a future release!
= note: for more information, see issue #79813 <https://github.com/rust-lang/rust/issues/79813>
= note: this error originates in the macro `dev_err` (in Nightly builds, run with -Z macro-backtrace for more info)
[ I was doubly surprised since upstream made it a deny-by-default lint
a year ago for Rust 1.91.0, and yet we didn't see it; plus I hadn't
seen this in my CI even yesterday.
It turns out this just landed into today's nightly (nightly-2026-07-16,
using upstream commit d0babd8b6):
Link: https://github.com/rust-lang/rust/pull/159222
which says:
"The `semicolon_in_expressions_from_macros` lint previously
suppressed warnings about non-local macros. This masks
a lint that will subsequently become a hard error."
So that explains it. And this is the PR that will make it a hard error
at some point in the future:
Link: https://github.com/rust-lang/rust/pull/159218
Thus starting with Rust 1.99.0 (expected 2026-10-01), we will be
seeing the deny-by-default lint above, so clean it up already.
- Miguel ]
Cc: stable@vger.kernel.org # Needed in 6.18.y and later.
Link: https://github.com/rust-lang/rust/issues/79813
Signed-off-by: Alice Ryhl <aliceryhl@google.com>
Reviewed-by: Gary Guo <gary@garyguo.net>
Acked-by: Danilo Krummrich <dakr@kernel.org>
Link: https://github.com/rust-lang/rust/pull/159218
Link: https://github.com/rust-lang/rust/pull/159222
Link: https://patch.msgid.link/20260716-device-trail-semicolon-v1-1-f48e9dcfae15@google.com
[ Fixed typo. ]
Signed-off-by: Miguel Ojeda <ojeda@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mic/linux
Pull landlock fix from Mickaël Salaün:
"This fixes TCP Fast Open support, specific test environments, and doc
warnings"
* tag 'landlock-7.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/mic/linux:
selftests/landlock: Skip scoped_signal subtest with MSG_OOB if not available
selftests/landlock: Fix screwed up pointers in the scoped_signal_test
landlock: Update formatting
landlock: Fix kernel-doc for the nested quiet layer flag
selftests/landlock: Add test for TCP fast open
landlock: Fix TCP Fast Open connection bypass
|
|
__host1x_bo_unpin() drops the last reference to the mapping and frees
it, so we can't dereference mapping afterwards. The cache itself
outlives the mapping, so use the cache local variable instead.
Reported-by: Dan Carpenter <error27@gmail.com>
Closes: https://lore.kernel.org/linux-tegra/ah6ErK6f4kVudVIA@stanley.mountain/T/#u
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patch.msgid.link/20260603-host1x-bocache-leak-fix-v1-1-494101dbfd30@nvidia.com
|
|
Switch iwl_scan_offload_match_info::matches to a fixed-size array and
adjust D3 netdetect size handling accordingly.
In MVM D3 paths, compute expected payload size as
offsetof(struct iwl_scan_offload_match_info, matches) + matches_len to
preserve previous behavior after the struct layout change.
In MLD D3 netdetect handling, keep the simple full-notification size
assumption and validate against sizeof(*notif) before accessing data.
This keeps scan offload / netdetect functionality unchanged while
making length checks consistent with the new struct definition.
Assisted-by: GitHubCopilot:gpt-5.3-codex
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260715215523.4c4346140bcc.I44313ac41daca352e6aecdba09a1c3570c3eea06@changeid
|
|
We shouldn't trust the firmware about the length of the wowlan packet.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260715215523.fbd989cc85e2.If68de403bfa4943732c025961154c20b01b09e83@changeid
|
|
When setting the TK for ranging with an associated peer, 32 bytes of
TK are copied from the vif key without verifying the actual key length
which may be only 16 bytes if CCMP-128 is used. Fix it by setting the
copy length according to the key cipher.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260715215523.e339570086bd.Iafff5aaf0e25f7d29e06f0ef456107c4062bbc7d@changeid
|
|
ba_notif->tid is a firmware-controlled u8 that is used directly
as an array index into tid_data[] without any validation. Add a
bounds check against IWL_MAX_TID_COUNT before dereferencing the
array.
Assisted-by: GitHubCopilot:gpt-5.3-codex
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260715215523.d7c3e75d47af.If88948108cfc8b5fb3ce5531d927855d1b3b6b30@changeid
|
|
mvmsta->tid_data was indexed by the TFD loop counter 'i' instead of
the actual TID value 'tid'. This writes lq_color into a random tid_data
slot unrelated to the BA entry.
Since multi-TID blockack is not really in use, 'i' was always 0 and no
harm was done.
Add a out-of-bound check before accessing the array.
Assisted-by: GitHubCopilot:gpt-5.3-codex
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260715215523.919edee567eb.Ie85c350e3afe2b39709d0039072740d86660f8ae@changeid
|
|
iwl_pcie_init_fw_sec() iterates over LMAC, UMAC, and paging
firmware sections and writes to ctxt_dram->lmac_img[i],
ctxt_dram->umac_img[i], and ctxt_dram->virtual_img[i] without
first verifying that the counts derived from the firmware image
do not exceed the array size. An oversized firmware image could
cause out-of-bounds writes into the fixed-size context-info DRAM
arrays.
Add explicit WARN_ON checks for all three section counts and
return -EINVAL if any is exceeded.
Assisted-by: GitHubCopilot:gpt-5.3-codex
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260715215523.34db46ca12f3.I1aa225492a62f25293c147aa7293afa80a5d4215@changeid
|
|
Release CMD_WANT_SKB response buffer after successful timestamp parsing
to avoid leaking response allocations.
Assisted-by: GitHubCopilot:GPT-5.3-Codex
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260715215523.31b38bef398b.Ib6a5a8bdd800779c8911da6859fd450d3d19c9e9@changeid
|
|
In iwl_mvm_wowlan_store_wake_pkt(), packet_len was initialized from
notif->wake_packet_length before the explicit check that len >=
sizeof(*notif).
Move the assignment of packet_len to after the size check so that
notif->wake_packet_length is only accessed once the payload length
has been validated.
Fixes: 219ed58feda9 ("wifi: iwlwifi: mvm: Add support for wowlan wake packet notification")
Signed-off-by: Shahar Tzarfati <shahar.tzarfati@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260715215523.99d5cf85a528.Ic4aa736011d4fe88e0cd19723d1d48bb24642198@changeid
|
|
iwl_pnvm_complete_fn() casts pkt->data directly to
struct iwl_pnvm_init_complete_ntfy and reads the status field
without first verifying that the firmware notification payload
is large enough to contain that structure.
Add a WARN_ON_ONCE check against sizeof(*pnvm_ntf) and return
early without reading uninitialised memory if the payload is too
short.
Fixes: b3e4c0f34c17 ("iwlwifi: move PNVM implementation to common code")
Assisted-by: GitHubCopilot:gpt-5.3-codex
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260715215523.7f2a669e5c75.I00465dcfcbccb250ae9af2d9bb305e24de1ba394@changeid
|
|
The expression list[*size++] increments the pointer 'size'
rather than the u8 value it points to (operator precedence: ++
binds to the pointer before the dereference). As a result the
block-list entry is written at the correct index but *size is
never incremented, so the caller's count stays at zero and
subsequent calls overwrite slot 0 every time.
Change to list[(*size)++] so that the value pointed to by size
is incremented after use as the array index.
Fixes: 5f4656610edb ("wifi: iwlwifi: extend TAS_CONFIG cmd support for v5")
Assisted-by: GitHubCopilot:gpt-5.3-codex
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260715215523.d2cd92242582.Ife4140a4e27be2a1cd9f886c5a9b376ce182a019@changeid
|
|
The SMEM parsers cast firmware response payloads directly to shared
memory configuration structures. A short response can leave fields
outside the received payload while the driver still dereferences them.
Check the response payload length before reading the base fields in
both parser variants. Require the full legacy extended layout before
reading internal TX FIFO data. Valid responses keep the same parsed
values.
Signed-off-by: Shahar Tzarfati <shahar.tzarfati@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260715215523.fbdb0016a91d.I5f6c6e04589a24a233559191170ccb43372dee63@changeid
|
|
The SAR GEO command response is cast to
iwl_geo_tx_power_profiles_resp without verifying the payload length.
A malformed or unexpected firmware response can lead to reading an
invalid structure layout.
Add an explicit size check before accessing the response data and
return -EIO when the payload size is wrong.
Fixes: f604324eefec ("iwlwifi: remove iwl_validate_sar_geo_profile() export")
Signed-off-by: Pagadala Yesu Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260715215523.7e749b7d374a.I4ef54548bff6c6e7c7a57bee771ac12508aad677@changeid
|
|
TX_CMD parsing uses frame_count to walk status entries and then
read the trailing SCD SSN. Make the minimum-length check follow
that exact runtime layout calculation before parsing the payload.
For new TX API, reject TX_CMD responses with frame_count != 1 and
warn/return in the aggregation handler to document that aggregated
accounting is expected via BA notifications.
Assisted-by: GitHubCopilot:gpt-5.3-codex
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260715215523.0474ee89bab9.I84f151aabecb8921b587da092f29f78c47128f0f@changeid
|
|
We need to expect more channels on devices that support UNII-9.
Since iwl_ext_nvm_channels and iwl_uhb_nvm_channels are just a prefix
of iwl_unii9_nvm_channels just use iwl_unii9_nvm_channels and modify the
number of channels if the device does not support UNII-9 channels.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260715215523.473f48e6135d.I0e93cda753558aa4d9e3efcdd52cbc2eb9302c4a@changeid
|
|
Validate txq_id from TX response notification before passing to
iwl_trans_reclaim(). Other reclaim paths in this file perform this
check to prevent out-of-bounds access on malformed notifications.
Assisted-by: GitHubCopilot:claude-haiku-4.5
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260715215523.b938c2dcf08d.I8a88ec359e229f1c41ac9c49fd9ce28a2b62b274@changeid
|
|
Pull xfs fixes from Carlos Maiolino:
"This contains mostly a series of bug fixes found by different LLM
models"
* tag 'xfs-fixes-7.2-rc4' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux: (21 commits)
xfs: don't zap bmbt forks if they are MAXLEVELS tall
xfs: clamp timestamp nanoseconds correctly
xfs: fully check the parent handle when it points to the rootdir
xfs: handle non-inode owners for rtrmap record checking
xfs: fix off-by-one error when calling xchk_xref_has_rt_owner
xfs: set xfarray killable sort correctly
xfs: grab rtrmap btree when checking rgsuper
xfs: write the rg superblock when fixing it
xfs: use the rt version of the cow staging checker
xfs: use rtrefcount btree cursor in xchk_xref_is_rt_cow_staging
xfs: don't wrap around quota ids in dqiterate
xfs: move cow_replace_mapping to xfs_bmap_util.c
xfs: make cow repair somewhat flaky when debugging knob enabled
xfs: don't replace the wrong part of the cow fork
xfs: resample the data fork mapping after cycling ILOCK
xfs: fix null pointer dereference in tracepoint
xfs: use xfs_csn_t for xlog_cil_push_now() push_seq parameter
xfs: tie zoned sysfs lifetime to zone info
xfs: fail recovery on a committed log item with no regions
xfs: splice unsorted log items back to the transaction after the loop
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xiang/erofs
Pull erofs fixes from Gao Xiang:
- Fix sanity checks for ztailpacking tail pclusters to avoid
false corruption reports
- Use more informative s_id for file-backed mounts
- Hide the meaningless "cache_strategy=" mount option on plain
(uncompressed) filesystems
- Remove the unneeded erofs_is_ishare_inode() helper
* tag 'erofs-for-7.2-rc4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/xiang/erofs:
erofs: hide "cache_strategy=" for plain filesystems
erofs: get rid of erofs_is_ishare_inode() helper
erofs: relax sanity check for tail pclusters due to ztailpacking
erofs: use more informative s_id for file-backed mounts
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix two cpufreq issues, one in the intel_pstate driver and one
in the core:
- Make cpufreq_update_pressure() use cpuinfo.max_freq as the default
reference frequency when arch_scale_freq_ref() returns 0 to allow
the scheduler to still take CPU frequency caps into account in
those cases (Rafael Wysocki)
- Use the HWP guaranteed performance level as the full capacity
performance in intel_pstate on hybrid systems when turbo
frequencies are not allowed to be used to make scale-invariance
work as expected in those cases (Rafael Wysocki)"
* tag 'pm-7.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: Make cpufreq_update_pressure() fall back to cpuinfo.max_freq
cpufreq: intel_pstate: Set non-turbo capacity to HWP_GUARANTEED_PERF()
|
|
A couple of new Dell laptops are shipping using the sidecar amp
configuration. Add the required kernel quirk to enable.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20260716144209.2411523-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/linux-pm
Pull pmdomain fixes from Ulf Hansson:
"imx:
- Assign child domains for imx93 to prevent power off when in use
- Fix i.MX8MP power up sequences
mediatek:
- Fix possible nullptr in HWV cleanup/on-check"
* tag 'pmdomain-v7.2-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/linux-pm:
pmdomain: mediatek: Fix possible nullptr KP in HWV cleanup/on-check
pmdomain: imx: Fix i.MX8MP VC8000E power up sequence
pmdomain: imx: Fix i.MX8MP power notifier
pmdomain: imx93-blk-ctrl: Extract PHY as shared domain for DSI/CSI
dt-bindings: power: imx93: Add MIPI PHY power domain
|
