| Age | Commit message (Collapse) | Author |
|---|
|
Compare the sampled clock values instead of their addresses. Comparing
addresses leaves the samples unsorted, preventing the code from discarding
the minimum and maximum samples.
Fixes: 1a5392479207 ("drm/i915/selftests: Measure CS_TIMESTAMP")
Signed-off-by: Emre Cecanpunar <emreleno@gmail.com>
Signed-off-by: Tvrtko Ursulin <tursulin@ursulin.net>
Link: https://lore.kernel.org/r/20260714220430.238433-1-emreleno@gmail.com
(cherry picked from commit 682ea2d28d18bb06f9fc663cb5ab7e80dc0e606a)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
The UV/Y plane DDB entriess are never cleared on
sk_wm_plane_disable_noatomic() and can leave stale DDB state
for NV12 planes on pre-Gen11 devices
Fixes: d34b59d5ba41 ("drm/i915: Add skl_wm_plane_disable_noatomic()")
Assisted-by: Copilot:claude-sonnet-4.6
Signed-off-by: Vinod Govindapillai <vinod.govindapillai@intel.com>
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
Link: https://patch.msgid.link/20260615203355.218578-2-vinod.govindapillai@intel.com
(cherry picked from commit 60f68a6ba298fd1e971a2d91576304bee89a16fc)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
The LTC3676_IRQSTAT_* bit definitions do not match the IRQSTAT
(Interrupt Request Status) register layout documented in Table 15
of the LTC3676/LTC3676-1 datasheet:
bit 0 - Pushbutton Status Active
bit 1 - Hard Reset Occurred
bit 2 - PGOOD Timeout Occurred
bit 3 - Undervoltage Warning
bit 4 - Undervoltage Standby (Fault) Occurred
bit 5 - Overtemperature Warning
bit 6 - Overtemperature Standby (Fault) Occurred
bit 7 - Reserved
The driver instead defines these starting at bit 3, one bit higher
than the datasheet specifies, which causes ltc3676_regulator_isr()
to check the wrong status bits and misreport (or miss) PGOOD
timeout, undervoltage and thermal warning/fault conditions.
Fix the bit offsets to match the datasheet.
Fixes: 37b918a034fe ("regulator: Add LTC3676 support")
Cc: stable@vger.kernel.org
Signed-off-by: Abhishek Ojha <Abhishek.ojha@savoirfairelinux.com>
Link: https://patch.msgid.link/20260715170408.295552-1-Abhishek.ojha@savoirfairelinux.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When ksmbd validates a compound (chained) SMB2 request,
ksmbd_smb2_check_message() reads pdu->StructureSize2 without first
checking that the compound element is large enough to contain it.
StructureSize2 is a 2-byte field at offset 64
(__SMB2_HEADER_STRUCTURE_SIZE) from the start of each element.
The compound-walking logic only guarantees that a full 64-byte SMB2
header is present for the trailing element: when NextCommand is 0, len is
reduced to the number of bytes remaining after next_smb2_rcv_hdr_off. A
remote client can craft a compound request whose last element has exactly
64 bytes, so the 2-byte StructureSize2 read at offset 64 extends one byte
past the receive buffer, producing a slab-out-of-bounds read.
BUG: KASAN: slab-out-of-bounds in ksmbd_smb2_check_message (fs/smb/server/smb2misc.c:402)
Read of size 2 at addr ffff888012ae31ac by task kworker/0:1/14
The buggy address is located 172 bytes inside of allocated 173-byte region
Workqueue: ksmbd-io handle_ksmbd_work
Call Trace:
...
kasan_report (mm/kasan/report.c:595)
ksmbd_smb2_check_message (fs/smb/server/smb2misc.c:402)
handle_ksmbd_work (fs/smb/server/server.c:119)
process_one_work (kernel/workqueue.c:3314)
worker_thread (kernel/workqueue.c:3397)
kthread (kernel/kthread.c:436)
ret_from_fork (arch/x86/kernel/process.c:158)
ret_from_fork_asm (arch/x86/entry/entry_64.S:245)
Reject any compound element that is too small to hold StructureSize2
before dereferencing it.
Fixes: e2f34481b24d ("cifsd: add server-side procedures for SMB3")
Reported-by: AutonomousCodeSecurity@microsoft.com
Signed-off-by: Xiang Mei (Microsoft) <xmei5@asu.edu>
Acked-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
smb3_preauth_hash_rsp() computes the SMB3.1.1 preauth integrity hash on
the response path. For a binding SESSION_SETUP it looks up the
per-connection preauth_session and reads its Preauth_HashValue.
smb2_sess_setup() frees that preauth_session under ksmbd_conn_lock().
Two SMB2 requests on one connection can run concurrently, so an unlocked
lookup and hash can use a preauth_session after another worker frees it.
Take ksmbd_conn_lock() before selecting conn->binding and hold it across
the selected preauth hash lookup and update. This preserves the existing
hash selection while preventing the lookup-to-use lifetime race.
Fixes: 1c5daa2ea924 ("ksmbd: handle channel binding with a different user")
Signed-off-by: Gil Portnoy <dddhkts1@gmail.com>
Acked-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
ksmbd_sessions_deregister() removes a connection's channels from other
sessions' channel lists only while conn->binding is still set:
if (conn->binding) {
hash_for_each_safe(sessions_table, ...)
ksmbd_chann_del(conn, sess);
}
conn->binding is a transient flag: it is cleared once a binding
SESSION_SETUP completes, and also by a subsequent non-binding
SESSION_SETUP on the same connection (a reauthentication on a bound
channel, or a new SessionId==0 setup). A connection that has bound a
channel into another session's ksmbd_chann_list and then clears
conn->binding leaves that channel behind when it disconnects: the
channel, whose chann->conn points at the now freed struct ksmbd_conn,
stays on the owner session's list.
When the owning connection later tears down, the second loop
dereferences the stale channel:
xa_for_each(&sess->ksmbd_chann_list, chann_id, chann)
if (chann->conn != conn)
ksmbd_conn_set_exiting(chann->conn); /* freed */
which is a use-after-free write into the freed ksmbd_conn (the same
stale channel is also walked by show_proc_session() through /proc). The
session is leaked as well, because its channel list never empties.
Remove the conn->binding gate so a connection always removes its
channels from every session on teardown.
Fixes: faf8578c77f3 ("ksmbd: find bound sessions during reauthentication")
Signed-off-by: Gil Portnoy <dddhkts1@gmail.com>
Acked-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
Commit 4b706360ffb7 ("ksmbd: fix multichannel binding and enforce channel
limit") moved the binding-path session key out of the session-wide
sess->sess_key (CIFS_KEY_SIZE = 40) into a new per-channel buffer, and
sized both that buffer and the on-stack copy used during binding with
SMB2_NTLMV2_SESSKEY_SIZE (16):
struct channel {
char sess_key[SMB2_NTLMV2_SESSKEY_SIZE]; /* 16 */
...
};
ntlm_authenticate() / krb5_authenticate():
char channel_key[SMB2_NTLMV2_SESSKEY_SIZE] = {}; /* 16 */
char *auth_key = conn->binding ? channel_key : sess->sess_key;
The two writers that fill this destination still bound the copy length
against CIFS_KEY_SIZE (40), not against the 16-byte buffer:
ksmbd_decode_ntlmssp_auth_blob() (NTLM key exchange):
if (sess_key_len > CIFS_KEY_SIZE) /* 40 */
return -EINVAL;
arc4_crypt(ctx_arc4, sess_key,
(char *)authblob + sess_key_off, sess_key_len);
ksmbd_krb5_authenticate():
if (resp->session_key_len > sizeof(sess->sess_key)) /* 40 */
...
memcpy(sess_key, resp->payload, resp->session_key_len);
On a binding SESSION_SETUP, auth_key points at the 16-byte channel_key,
so a client that supplies an NTLM EncryptedRandomSessionKey of up to 40
bytes (with NTLMSSP_NEGOTIATE_KEY_EXCH), or a Kerberos ticket whose
session key is longer than 16 bytes (a normal AES256 key is 32), writes
past the 16-byte stack buffer -- up to a 24-byte kernel stack overflow.
KASAN reports it as a stack-out-of-bounds write in arc4_crypt() called
from ksmbd_decode_ntlmssp_auth_blob().
The destinations must be able to hold the full session key the length
checks already permit. Size the per-channel key buffer and the two
on-stack channel_key buffers with CIFS_KEY_SIZE, matching sess->sess_key.
Fixes: 4b706360ffb7 ("ksmbd: fix multichannel binding and enforce channel limit")
Signed-off-by: Gil Portnoy <dddhkts1@gmail.com>
Acked-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
On an SMB2 SET_INFO(FileRenameInformation) whose target names an alternate
data stream, smb2_rename() obtains a formatted stream-name string from
ksmbd_vfs_xattr_stream_name(), which allocates it with kasprintf() and
returns it through an out-param:
rc = ksmbd_vfs_xattr_stream_name(stream_name, &xattr_stream_name, ...);
if (rc)
goto out;
rc = ksmbd_vfs_setxattr(..., xattr_stream_name, ...);
if (rc < 0) {
...
goto out;
}
goto out;
xattr_stream_name is declared inside the alternate-data-stream block, but
the out: label is outside that block and frees only new_name, so it cannot
release xattr_stream_name. ksmbd_vfs_setxattr() takes a const char * and
only reads the name, so it does not take ownership either. Both the
setxattr-failure and the success path therefore leak the kasprintf()'d
string. An authenticated client with a writable share can leak kernel
memory on every stream rename, exhausting kernel memory over time.
Free xattr_stream_name after its use, before the block's goto out. The
two earlier goto out paths never assign the variable, so there is no
double-free.
Signed-off-by: Gil Portnoy <dddhkts1@gmail.com>
Acked-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
Commit 6b9a2e09d4cc ("ksmbd: avoid zeroing the read buffer in smb2_read()")
switched the SMB2 READ payload buffer from kvzalloc() to kvmalloc(), on the
premise that only the nbytes actually read are ever transmitted, so the
ALIGN(length, 8) tail need not be initialized.
That premise does not hold for a compound response. ksmbd_vfs_read() fills
only nbytes, leaving [nbytes, ALIGN(length, 8)) uninitialized. The aux
payload is pinned as the last response iov with iov_len == nbytes, but when
the READ is a member of a compound, init_chained_smb2_rsp() 8-byte-aligns
the previous member by extending that same iov:
new_len = ALIGN(len, 8);
work->iov[work->iov_idx].iov_len += (new_len - len);
inc_rfc1001_len(work->response_buf, new_len - len);
so up to 7 uninitialized bytes of the kvmalloc()'d slab tail are sent
to the client. When the read length is small the buffer is served from
a general kmalloc slab, so those bytes can be stale kernel-heap
contents, including pointer values -- an information leak usable to
defeat KASLR.
An authenticated client triggers it with a compound request containing a
READ whose returned nbytes is not 8-aligned (for example [READ, CLOSE] with
a 1-byte read).
Zero only the alignment tail after the read, preserving the bulk
no-zeroing optimization of 6b9a2e09d4cc.
Fixes: 6b9a2e09d4cc ("ksmbd: avoid zeroing the read buffer in smb2_read()")
Cc: stable@vger.kernel.org
Signed-off-by: Gil Portnoy <dddhkts1@gmail.com>
Acked-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
smb2_oplock_break_noti() and smb2_lease_break_noti() store a ksmbd_conn
pointer in an async ksmbd_work and then queue that work on ksmbd-io. The
work only increments conn->r_count, which prevents teardown from passing
the pending-request wait after the increment, but it does not pin the
struct ksmbd_conn object.
If connection teardown races with an oplock break notification, the last
conn reference can be dropped before the queued worker finishes. The
worker then uses the freed conn in ksmbd_conn_write() and
ksmbd_conn_r_count_dec().
Take a real conn reference when publishing the conn pointer to the async
work item, and drop it after the notification work has decremented
r_count. Apply the same lifetime rule to lease break notification, which
uses the same work->conn pattern.
Fixes: 3aa660c05924 ("ksmbd: prevent connection release during oplock break notification")
Signed-off-by: Qihang <q.h.hack.winter@gmail.com>
Acked-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
set_file_allocation_info() converts the client-supplied
FILE_ALLOCATION_INFORMATION::AllocationSize into a 512-byte block
count with:
alloc_blks = (le64_to_cpu(file_alloc_info->AllocationSize) + 511) >> 9;
AllocationSize is a fully client-controlled __le64 field; the only
validation performed by the caller (smb2_set_info_file(), case
FILE_ALLOCATION_INFORMATION) is that the fixed buffer is at least
sizeof(struct smb2_file_alloc_info) == 8 bytes. The value itself is
never range-checked before this arithmetic.
When AllocationSize is close to U64_MAX (e.g. 0xffffffffffffffff),
"AllocationSize + 511" wraps around mod 2^64 to a small number
(0xffffffffffffffff + 511 = 510), so alloc_blks becomes 0. Since any
existing regular file has stat.blocks > 0, the function then takes
the "shrink" branch and calls:
ksmbd_vfs_truncate(work, fp, alloc_blks * 512); /* == 0 */
silently truncating the file to size 0, even though the client asked
to grow the allocation to (what looks like) the maximum possible
size. The trailing "if (size < alloc_blks * 512) i_size_write(inode,
size);" restore is guarded by a comparison that is never true once
alloc_blks == 0, so the truncation is not undone. This lets an
authenticated SMB client that already holds an open handle with
FILE_WRITE_DATA on a file silently truncate that same file to size 0
via a single crafted SET_INFO(FILE_ALLOCATION_INFORMATION) request
advertising a near-U64_MAX AllocationSize, even though the request
asks to grow the file's allocation rather than shrink it. This is a
functional/data-loss bug, not a privilege-boundary
violation: the same client could already truncate the file via
FILE_END_OF_FILE_INFORMATION or a plain write.
Fix it by validating AllocationSize against MAX_LFS_FILESIZE, the
same upper bound the VFS itself uses to reject unrepresentable file
sizes, before doing the "+511" rounding, and rejecting oversized
values with -EINVAL. Bounding AllocationSize to
MAX_LFS_FILESIZE - 511 guarantees the "+511" addition cannot wrap,
and that the subsequent "alloc_blks * 512" values passed to
vfs_fallocate() and ksmbd_vfs_truncate() stay within a representable
loff_t as well.
No legitimate SMB client asks for an allocation size anywhere near
2^64 bytes, so this only rejects a value that was previously
silently misinterpreted as zero.
Runtime-verified on a v6.19 KASAN test stand: sending SET_INFO
(FILE_ALLOCATION_INFORMATION) with AllocationSize = 0xffffffffffffffff
against ksmbd now returns -EINVAL and leaves the target file's size
unchanged, where the unpatched kernel truncated it from 4096 to 0
bytes.
Fixes: e2f34481b24d ("cifsd: add server-side procedures for SMB3")
Cc: stable@vger.kernel.org
Signed-off-by: Ibrahim Hashimov <security@auditcode.ai>
Assisted-by: AuditCode-AI:2026.07
Acked-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
This reverts commit e0c48e42d818 ("usb: typec: ucsi: yoga-c630: remove
duplicate AltModes").
The yoga_c630 driver previously implemented its own duplicate altmode
detection in yoga_c630_ucsi_update_altmodes() to work around buggy EC
firmware that returns duplicate AltModes instead of empty ones.
With the introduction of the common ucsi_altmode_is_duplicate() helper
in both the standard and nvidia registration paths, duplicate detection
is now handled automatically in the core UCSI code. This makes the
yoga_c630-specific implementation added in commit e0c48e42d818 ("usb:
typec: ucsi: yoga-c630: remove duplicate AltModes") redundant.
Remove yoga_c630_ucsi_update_altmodes() and its callback to eliminate
code duplication and simplify the driver. Note that this causes the
driver to switch back from the nvidia registration path to the standard
path, which is the original behavior before commit e0c48e42d818 ("usb:
typec: ucsi: yoga-c630: remove duplicate AltModes"). Both paths now
include duplicate detection, ensuring the firmware bug is still properly
handled.
Signed-off-by: Chia-Lin Kao (AceLan) <acelan.kao@canonical.com>
Link: https://patch.msgid.link/20260713084323.287516-3-acelan.kao@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Extend the duplicate altmode detection to ucsi_register_altmodes_nvidia()
which is used when a driver provides the update_altmodes() callback.
This ensures all drivers benefit from duplicate detection, whether they
use the standard registration path or the nvidia path with update_altmodes
callback.
Without this fix, drivers using the nvidia path (like yoga_c630) would
still encounter duplicate altmode registration errors from buggy firmware.
Fixes: a79f16efcd00 ("usb: typec: ucsi: Add support for the partner USB Modes")
Cc: stable <stable@kernel.org>
Signed-off-by: Chia-Lin Kao (AceLan) <acelan.kao@canonical.com>
Link: https://patch.msgid.link/20260713084323.287516-2-acelan.kao@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some firmware implementations incorrectly return the same altmode
multiple times at different offsets when queried via
UCSI_GET_ALTERNATE_MODES. This causes sysfs duplicate filename errors
and kernel call traces when the driver attempts to register the same
altmode twice:
sysfs: cannot create duplicate filename '/devices/.../typec/port0/port0.0/partner'
typec-thunderbolt port0-partner.1: failed to create symlinks
typec-thunderbolt port0-partner.1: probe with driver typec-thunderbolt failed with error -17
The matching rules differ by recipient:
- UCSI_RECIPIENT_CON (port) and UCSI_RECIPIENT_SOP_P (plug):
Two altmodes with identical SVID and VDO are byte-for-byte
duplicates and the second has no observable function, so drop it.
- UCSI_RECIPIENT_SOP (partner):
The typec class binds each partner altmode to a port altmode of
the same SVID via altmode_match()/device_find_child(), which
returns the first port altmode with a matching SVID. If the
partner advertises more altmodes for SVID X than the port
advertises, the surplus partner altmode(s) collapse onto an
already-paired port altmode and trigger the
"duplicate filename .../partner" sysfs error during
typec_altmode_create_links(). Use the port-side altmode count for
SVID X as the authoritative cap and reject any partner altmode
that would exceed it. This preserves legitimate multi-Mode
partner altmodes (vendor SVIDs that the port really does
advertise more than once) while filtering the firmware-generated
duplicates that have no port counterpart, and is therefore
stricter than a plain SVID+VDO comparison (which still admits the
Thunderbolt case where firmware reports the same SVID twice with
different VDOs) without being over-broad like a plain SVID match
(which would falsely drop legitimate vendor multi-Mode entries).
If a duplicate is detected, skip it and emit a clean warning instead
of generating a kernel call trace:
ucsi_acpi USBC000:00: con2: Firmware bug: duplicate partner altmode SVID 0x8087 at offset 1, ignoring.
ucsi_acpi USBC000:00: con2: VDO mismatch: 0x8087a043 vs 0x00000001
The duplicate detection logic lives in a reusable helper
ucsi_altmode_is_duplicate() and is invoked from
ucsi_register_altmodes(). It applies to all three recipient types:
partner (SOP), port (CON), and plug (SOP_P) altmodes.
Fixes: a79f16efcd00 ("usb: typec: ucsi: Add support for the partner USB Modes")
Cc: stable <stable@kernel.org>
Signed-off-by: Chia-Lin Kao (AceLan) <acelan.kao@canonical.com>
unchanged: still SVID+VDO exact-dup match.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://patch.msgid.link/20260713084323.287516-1-acelan.kao@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
dummy_hcd embeds a single shared usb_request (dum->fifo_req) that the
"emulated single-request FIFO" fast-path in dummy_queue() reuses for
small IN transfers: it copies the caller's request into it
(req->req = *_req) and queues it, treating list_empty(&fifo_req.queue)
as "the slot is free".
The completion side (dummy_timer/transfer/nuke/dummy_dequeue) follows
the standard pattern: list_del_init(&req->queue) unlinks the request,
then the lock is dropped and usb_gadget_giveback_request() invokes
req->complete(). But list_del_init() makes fifo_req.queue look empty
*before* the completion callback returns, so a concurrent dummy_queue()
on another CPU sees the slot as free, reuses fifo_req and runs
req->req = *_req -- overwriting req->complete while dummy_timer is
mid-calling it. The indirect call then jumps to a clobbered pointer,
causing a general protection fault / page fault in dummy_timer
(syzkaller extid faf3a6cf579fc65591ca). The clobbering write is an
in-bounds memcpy on a live shared object, so KASAN cannot flag it.
Add a fifo_req_busy bit covering the shared request's whole lifetime:
set it in dummy_queue() when the FIFO fast-path takes fifo_req (making
it the fast-path guard, replacing the list_empty(&fifo_req.queue)
test), and clear it after the completion callback has returned, via a
dummy_giveback() helper used at all four gadget-request giveback
sites. The shared slot can no longer be reused until its completion
callback has finished.
Reported-by: syzbot+faf3a6cf579fc65591ca@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=faf3a6cf579fc65591ca
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable <stable@kernel.org>
Signed-off-by: Jinchao Wang <wangjinchao600@gmail.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://patch.msgid.link/5db8bba5b3499a86cd2e776f9918126b68b2508b.1784198306.git.wangjinchao600@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The probe() calls pm_runtime_use_autosuspend(), but remove() does not call
pm_runtime_dont_use_autosuspend(). This can lead to a usage_count leak if
autosuspend_delay is set to a negative value.
The pm_runtime_use_autosuspend() also notes that it's important to undo
this with pm_runtime_dont_use_autosuspend() at driver exit time.
Fixes: 1f874edcb731 ("usb: chipidea: add runtime power management support")
Cc: stable <stable@kernel.org>
Assisted-by: Claude:claude-sonnet-4.6
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260716104126.2763454-1-xu.yang_2@oss.nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add a lock to the function bos_descriptors_read().
This function accesses udev->bos, which could be simultaneously freed in
usb_reset_and_verify_device(), a function that is commonly called in
drivers all over the kernel.
Assisted-by: gkh_clanker_t1000
Signed-off-by: Griffin Kroah-Hartman <griffin@kroah.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Link: https://patch.msgid.link/20260715-usb_core_patches_3-v1-1-53021f5576fd@kroah.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
omap2430_probe() stores pdev->dev.of_node in a local np variable. This is
a borrowed pointer and the probe function does not take a reference to
it.
The success and error paths nevertheless call of_node_put(np). This drops
a reference that is owned by the platform device, and can leave
pdev->dev.of_node with an unbalanced reference count.
Do not put the borrowed platform device node from omap2430_probe().
References taken for the child MUSB device are handled by the device core,
and the ctrl-module phandle reference is still released separately.
Fixes: ffbe2feac59b ("usb: musb: omap2430: Fix probe regression for missing resources")
Cc: stable <stable@kernel.org>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Guangshuo Li <lgs201920130244@gmail.com>
Link: https://patch.msgid.link/20260713114711.955253-1-lgs201920130244@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
connector_unbind() is the mirror of connector_bind(), but it is missing
the symmetric call to typec_deattach() that connector_bind() makes via:
if (port_dev->child)
typec_attach(port_dev->connector, &port_dev->child->dev);
When a Thunderbolt dock is unplugged, two teardown paths race:
1. The component framework calls connector_unbind() first, which sets
port_dev->connector = NULL without calling typec_deattach(). This
leaves port->usb2_dev/port->usb3_dev in struct typec_port pointing at
the USB device that is about to be freed.
2. usb_disconnect() then calls typec_deattach(port_dev->connector, ...),
but port_dev->connector is already NULL, so the call is a no-op and
port->usb2_dev is never cleared.
3. Concurrently, UCSI detects a PD partner-disconnect event and calls
typec_unregister_partner(), which reads port->usb2_dev (now a dangling
pointer to freed memory) and passes it to typec_partner_unlink_device()
-> sysfs_remove_link() -> dev_name() on the freed device, corrupting
the typec/UCSI partner state.
This corruption leaves the Thunderbolt tunnel in an inconsistent state on
the next dock hot-plug. On affected hardware the dock's I225/igc NIC fails
to enumerate: AER fires a slot reset while the igc driver is still
initialising ("PCIe link lost"), and the subsequent igc_reset attempt hits
igc_rd32 on an already-detached device:
igc 0000:2e:00.0 eth0: PCIe link lost, device now detached
igc: Failed to read reg 0x0!
WARNING: CPU: 9 PID: 129 at drivers/net/ethernet/intel/igc/igc_main.c:7005
igc_rd32+0xa4/0xc0 [igc]
Call Trace:
igc_disable_pcie_master+0x16/0xa0 [igc]
igc_reset_hw_base+0x14/0x170 [igc]
igc_reset+0x63/0x110 [igc]
igc_io_slot_reset+0x9e/0xd0 [igc]
report_slot_reset+0x5d/0xc0
pcie_do_recovery+0x209/0x400
aer_isr_one_error_type+0x235/0x430
aer_isr+0x4e/0x80
irq_thread+0xf4/0x1f0
4. UCSI later handles the PD partner-disconnect and calls
typec_unregister_partner(), which still sees the stale port->usb2_dev
and tries to remove its sysfs link a second time:
kernfs: can not remove 'typec', no directory
WARNING: CPU: 6 PID: 55 at fs/kernfs/dir.c:1706 kernfs_remove_by_name_ns+0xe9/0xf0
Workqueue: events ucsi_handle_connector_change [typec_ucsi]
Call Trace:
sysfs_remove_link+0x19/0x50
typec_unregister_partner+0x6e/0x120 [typec]
ucsi_unregister_partner+0x107/0x150 [typec_ucsi]
ucsi_handle_connector_change+0x3ec/0x490 [typec_ucsi]
process_one_work+0x18e/0x3e0
worker_thread+0x2e3/0x420
kthread+0x10a/0x230
ret_from_fork+0x121/0x140
ret_from_fork_asm+0x1a/0x30
With worse timing the same stale pointer is dereferenced after the
backing memory is freed, turning the warning into a use-after-free.
Fix the asymmetry: call typec_deattach() before clearing
port_dev->connector, matching what connector_bind() does on the bind side.
typec_partner_deattach() is already protected by port->partner_link_lock,
so it serialises safely with the concurrent typec_unregister_partner() path.
Fixes: 11110783f5ea ("usb: Inform the USB Type-C class about enumerated devices")
Cc: stable <stable@kernel.org>
Signed-off-by: Chia-Lin Kao (AceLan) <acelan.kao@canonical.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://patch.msgid.link/20260611071201.1235545-1-acelan.kao@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When logging the decode of a data abort we currently unconditionally decode
and display Xs. Currently the only defined non-RES0 values for this field
are for cases where ISV=1, move the decode of Xs into our existing check
for ISV=1. This avoids potential confusion if some other use is assigned to
these bits for ISV=0 cases in future, or misleading someone into thinking
there is a meaningful value there with currently defined architecture.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Will Deacon <will@kernel.org>
|
|
The Longmai Technologies USB Key (0x04b4:0xb708) advertises itself as a
SCSI/Bulk-only mass storage device but does not correctly handle ATA
pass-through commands. When such a command (ATA_12 or ATA_16) is sent to
the device it fails to respond and the transfer eventually times out,
leaving the device unusable.
Add an unusual_devs entry for this device that sets the US_FL_NO_ATA_1X
flag, so usb-storage short-circuits ATA pass-through commands and returns
INVALID COMMAND OPERATION CODE (0x20 0x05 0x24 0x00) instead of forwarding
them to the device.
Information about the device in /sys/kernel/debug/usb/devices:
T: Bus=02 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 12 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=06 Prot=50 MxPS=64 #Cfgs= 1
P: Vendor=04b4 ProdID=b708 Rev= 1.00
S: Manufacturer=Longmai Technologies
S: Product=USB Key
C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Reported-by: Ai Chao <aichao@kylinos.cn>
Cc: stable <stable@kernel.org>
Signed-off-by: Huang Wei <huangwei@kylinos.cn>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://patch.msgid.link/20260716033341.2830872-1-huangwei@kylinos.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Admin-only PF mode does not expose media or 3D execution capabilities
to userspace, so display pipelines cannot receive rendered content.
Fixes: d88c4bac8c2a ("drm/xe/pf: Restrict device query responses in admin-only PF mode")
Signed-off-by: Satyanarayana K V P <satyanarayana.k.v.p@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Piotr Piórkowski <piotr.piorkowski@intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Piotr Piórkowski <piotr.piorkowski@intel.com>
Link: https://patch.msgid.link/20260714053259.504308-2-satyanarayana.k.v.p@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
(cherry picked from commit 7ef55ae582eba2b0a7a7441bd3b9aefd38a26bb9)
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
|
|
GuC exec queue destruction can run asynchronously. If the final device
put happens from a destroy worker, drmm cleanup can end up draining
the same workqueue and deadlock.
Hold a drm_device reference for the queue lifetime and drop it after
queue teardown completes. This keeps drmm cleanup from running while
async destroy work is still pending.
Move GuC destroy work to a module-lifetime Xe workqueue and flush it
on PCI remove so hot-unbind/rebind still waits for pending destroy work.
With queue-held device refs, guc_submit_sw_fini() cannot run with live
GuC IDs. Replace the fini wait with an assertion and remove the unused
fini_wq.
v2:
- Rebase
v3:
- Switch to queue-lifetime drm_dev_get()/drm_dev_put() model. (Matt)
- Queue async teardown on system_dfl_wq instead of xe->destroy_wq. (Matt)
- Drop separate deferred drm_dev_put worker.
- Remove stale drain_workqueue(xe->destroy_wq) from guc_submit_sw_fini().
v4:
- Replace the guc_submit_sw_fini() wait with an assertion and remove
the now-unused fini_wq. (sashiko)
v5:
- Move destroy work to a module-lifetime Xe workqueue instead of
system_dfl_wq. (Matt)
- Flush the module-lifetime destroy workqueue during PCI remove to
preserve the old device-remove wait semantics.
v6:
- Keep SVM pagemap destroy work on the per-device destroy_wq to avoid
letting it outlive the xe_device/drm_device. (Sashiko)
- Use WQ_MEM_RECLAIM for xe->destroy_wq because SVM pagemap destroy work
can be queued from the reclaim path.
v7:
- Drop the per-device xe->destroy_wq and use the module-level destroy WQ
for SVM pagemap destroy as well. (Matt)
- Rename xe_exec_queue_destroy_wq_*() helpers to xe_destroy_wq_*()
helpers because the WQ is no longer exec-queue specific. (Matt)
v8:
- Rebase.
v9:
- Keep SVM pagemap destroy work on the per-device WQ_MEM_RECLAIM
destroy_wq because it can be queued from reclaim and embeds
the dev_pagemap used by devres teardown. (Sashiko)
- Keep the module-level destroy WQ GuC-only and drop WQ_MEM_RECLAIM
from it.
- Update the module-WQ kdoc to document the GuC/SVM split.
v10:
- Keep xe->destroy_wq per-cpu while adding WQ_MEM_RECLAIM to fix the
workqueue allocation warning.
v11:
- Drop the SVM pagemap destroy comment as it was revision-specific.
(Thomas)
v12:
- Rebase.
Fixes: 2d2be279f1ca ("drm/xe: fix UAF around queue destruction")
Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Himal Prasad Ghimiray <himal.prasad.ghimiray@intel.com>
Cc: Tejas Upadhyay <tejas.upadhyay@intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Signed-off-by: Arvind Yadav <arvind.yadav@intel.com>
Link: https://patch.msgid.link/20260716062624.211396-1-arvind.yadav@intel.com
Signed-off-by: Tejas Upadhyay <tejas.upadhyay@intel.com>
(cherry picked from commit da1124abac689cc2b1d8995e5f0a816f8a122edb)
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
|
|
The scheduler keeps a pointer to the timeline name, but q->name
is freed with the exec queue while scheduler fences can still
reference it.
Store the name in struct xe_guc_exec_queue so it shares
the scheduler's RCU-deferred lifetime.
Fixes: 6bd90e700b42 ("drm/xe: Make dma-fences compliant with the safe access rules")
Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Himal Prasad Ghimiray <himal.prasad.ghimiray@intel.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Signed-off-by: Arvind Yadav <arvind.yadav@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@igalia.com>
Acked-by: Matthew Brost <matthew.brost@intel.com>
Link: https://patch.msgid.link/20260714064402.2457257-1-arvind.yadav@intel.com
Signed-off-by: Tejas Upadhyay <tejas.upadhyay@intel.com>
(cherry picked from commit 41075f0eb5dcbd3b065d15f15ef7bbe9315188e8)
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
|
|
xe_pt_update_ops_init() fails to reset current_op to 0. On the
vm_bind path, ops_execute() calls xe_pt_update_ops_prepare() inside
the xe_validation_guard() / drm_exec_until_all_locked() loop. When
that loop retries due to lock contention or OOM eviction
(drm_exec_retry_on_contention() / xe_validation_retry_on_oom()),
xe_pt_update_ops_prepare() runs again on the same vops, and each
call to bind_op_prepare() increments current_op without resetting it.
After N retries current_op exceeds the array size allocated by
xe_vma_ops_alloc(), causing an out-of-bounds write into
SLUB-poisoned memory and a subsequent UAF crash in
xe_migrate_update_pgtables_cpu() when reading the corrupted pt_op->bind.
Also reset needs_svm_lock and needs_invalidation which are derived in
the same prepare pass and would otherwise cause wrong migrate ops
selection and redundant TLB invalidation on retry.
Fix this by resetting current_op, needs_svm_lock and needs_invalidation
in xe_pt_update_ops_init().
v2 (Matt):
- Add details in commit message.
- Add Fixes tag and Cc to stable@vger.kernel.org
Fixes: e8babb280b5e ("drm/xe: Convert multiple bind ops into single job")
Suggested-by: Matthew Auld <matthew.auld@intel.com>
Cc: stable@vger.kernel.org
Assisted-by: GitHub-Copilot:claude-sonnet-4.6
Signed-off-by: Zongyao Bai <zongyao.bai@intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Link: https://patch.msgid.link/20260714232433.2737533-1-zongyao.bai@intel.com
(cherry picked from commit 046045543e530605c441063535e7dca0075369a6)
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
|
|
Starting on LNL the WOPCM size is 8MB instead of 4, so we need to avoid
using the [0, 8MB) range of the GGTT as that can be unaccessible from
the microcontrollers.
Note that the proper long-term fix here is to read the WOPCM size from
the HW, but that is a more serious rework that would be difficult to
backport, so we can do that as a follow-up.
Fixes: 9c57bc08652a ("drm/xe/lnl: Drop force_probe requirement")
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Shuicheng Lin <shuicheng.lin@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Shuicheng Lin <shuicheng.lin@intel.com>
Link: https://patch.msgid.link/20260713221758.3285744-2-daniele.ceraolospurio@intel.com
(cherry picked from commit 3033b0b24ed0e2f5e56bdd4d9c183417c365a45b)
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
|
|
xe_bo_move() attaches VF CCS read/write batch buffers (BBs) to a BO
after it transitions NULL/SYSTEM -> TT, and detaches them after it
transitions TT -> SYSTEM. Both operations were done synchronously on
the CPU immediately after building the move's copy/clear fence,
without waiting for that fence to signal. This creates two races with
VF migration:
- Attach happens too late relative to the copy job it is meant to
protect. If the copy job is submitted before the CCS BBs are
attached, a VF migration event that pauses execution mid-copy can
observe partially copied CCS metadata without the attach state
needed to correctly save/restore it.
- Detach happens too early relative to the copy job that moves data
out of TT. The CCS BBs are torn down right after the copy fence is
obtained, while the actual blit may still be in flight. A VF
migration event that pauses execution mid-copy can then race the
save/restore path against the still-running blit, and the CCS BBs
it would need to make sense of the paused state have already been
removed.
Fix both races:
- Move the attach call to before the copy/clear job is submitted, so
the CCS BBs are already registered by the time the copy runs. On
attach failure, unwind and bail out of the move. xe_migrate_ccs_rw_copy()
now takes the destination resource explicitly, since bo->ttm.resource
is not updated to the new resource until after the move commits.
- Detach only after explicitly waiting for the copy fence to signal,
instead of tearing down the CCS BBs immediately after obtaining it.
While here, also fix xe_sriov_vf_ccs_attach_bo() to properly unwind and
propagate errors: the per-context loop previously never broke out on
error, silently discarding earlier failures. Unwind by clearing each
attached context directly via xe_migrate_ccs_rw_copy_clear() instead of
reusing xe_sriov_vf_ccs_detach_bo(), which requires both contexts to be
attached before it will clean up either one.
Fixes: 864690cf4dd6 ("drm/xe/vf: Attach and detach CCS copy commands with BO")
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Satyanarayana K V P <satyanarayana.k.v.p@intel.com>
Assisted-by: GitHub_Copilot:claude-sonnet-5
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Acked-by: Satyanarayana K V P <satyanarayana.k.v.p@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patch.msgid.link/20260714062440.3421225-1-matthew.brost@intel.com
(cherry picked from commit d45ad0aa7a1eb5d7288b5ed948b05695611dc39e)
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
|
|
The witable override should be set when FDO_MODE bit is enabled.
Fix the comparison to distingush this case from legacy systems
where bit should be disabled to have override.
Cc: stable@vger.kernel.org
Fixes: 9dde74fd9e65 ("drm/xe/nvm: enable cri platform")
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patch.msgid.link/20260714-cri_nvm_fdo_flip-v2-1-14580e71b58e@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
(cherry picked from commit 2007be18d2318a59748da5da1b8968042213d5f1)
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
|
|
An imported dma-buf BO is created as a ttm_bo_type_sg BO whose
reservation object is the exporter's dma_buf->resv. The importer,
however, only takes a dma-buf reference after a successful
dma_buf_dynamic_attach(). Until then nothing keeps the exporter alive,
so if the exporter is freed while the BO still references its resv, a
later access to that resv is a use-after-free:
Oops: general protection fault, probably for non-canonical address
0x6b6b6b6b6b6b6b9c
Workqueue: ttm ttm_bo_delayed_delete [ttm]
RIP: 0010:mutex_can_spin_on_owner+0x3f/0xc0
This can be reached on two paths:
- dma_buf_dynamic_attach() fails, or
- ttm_bo_init_reserved() fails during BO creation.
In both cases the BO already has bo->base.resv pointing at the exporter
resv, and sg BOs are always torn down via ttm_bo_delayed_delete(), which
locks bo->base.resv asynchronously - potentially after the exporter has
been freed.
Take the dma-buf reference in xe_bo_init_locked(), before
ttm_bo_init_reserved(), so it also covers a creation failure there, and
release it in xe_ttm_bo_destroy(). The reference is held for the whole
BO lifetime, keeping the shared resv alive on every path.
v2:
- Reworked the fix to avoid creating the imported sg BO before
dma_buf_dynamic_attach() succeeds.
- Attach with importer_priv == NULL and make invalidate_mappings ignore
incomplete imports.
v3:
- Dropped the xe-side reordering approach since importer_priv must be
valid when dma_buf_dynamic_attach() publishes the attachment.
- Per Christian's suggestion on the v1 thread, keyed the check on
import_attach rather than removing the sg guard entirely.
- Fixes both xe and amdgpu in a single TTM patch.
v4:
- Moved import_attach check to after dma_resv_copy_fences() so fences
are copied before returning for successful imports (Thomas).
- Removed exporter-alive claim from commit message (Thomas).
v5:
- Add drm/xe patch to keep imported sg BOs off the LRU before attach
succeeds; the TTM fix alone is not sufficient for xe if the BO is
already LRU-visible. (Thomas)
v4 patch:
https://patchwork.freedesktop.org/patch/736663/?series=169129&rev=2
- Patch 1 (drm/ttm) carries Christian's Reviewed-by from v4.
v6:
- Reworked the fix based on Thomas' suggestion. Instead of the TTM resv
individualization (v1-v5) plus the xe off-LRU/placement handling (v5),
just hold a dma-buf reference for the imported BO lifetime so the
shared resv can never be freed while the BO still references it.
Single xe patch, no TTM change. (Thomas)
- Take the reference in xe_bo_init_locked() before ttm_bo_init_reserved()
so a TTM creation failure is covered too (Thomas).
- Dropped the v5 series (drm/ttm + drm/xe off-LRU); the off-LRU approach
also regressed in CI BAT via ttm_bo_pipeline_gutting() creating a ghost
BO that outlived the exporter.
Link to v5: https://patchwork.freedesktop.org/series/169984/
v7:
- Move changelog above --- so it stays in the commit message.
- Reorder changelog entries oldest-to-newest. (Thomas)
Closes: https://gitlab.freedesktop.org/drm/xe/kernel/-/work_items/8023
Fixes: dd08ebf6c352 ("drm/xe: Introduce a new DRM driver for Intel GPUs")
Cc: stable@vger.kernel.org
Cc: Thomas Hellstrom <thomas.hellstrom@linux.intel.com>
Cc: Christian Konig <christian.koenig@amd.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Suggested-by: Thomas Hellstrom <thomas.hellstrom@linux.intel.com>
Assisted-by: GitHub_Copilot:claude-sonnet-4.6
Reviewed-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Signed-off-by: Nitin Gote <nitin.r.gote@intel.com>
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patch.msgid.link/20260710191027.260160-2-nitin.r.gote@intel.com
(cherry picked from commit 3516f3fae6be35642f8f06f8a218da6425c0306a)
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
|
|
When prefetch region is DRM_XE_CONSULT_MEM_ADVISE_PREF_LOC for a BO VMA,
the code used it as an index into region_to_mem_type[], causing an
out-of-bounds access since the value is -1.
Resolve the preferred location for BO VMAs directly: local VRAM on dGFX
(using the BO's tile placement) or system memory on iGPU.
Discovered using AI-assisted static analysis confirmed by Intel Product
Security.
v2:
-Fix null dereference
Reported-by: Martin Hodo <martin.hodo@intel.com>
Fixes: c1bb69a2e8e2 ("drm/xe/svm: Consult madvise preferred location in prefetch")
Cc: Matthew Brost <matthew.brost@intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20260624174943.2808767-2-himal.prasad.ghimiray@intel.com
Signed-off-by: Himal Prasad Ghimiray <himal.prasad.ghimiray@intel.com>
(cherry picked from commit d9a4906ac03be9f6ed3f3b45c56c866b867fd75b)
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
|
|
Richard Fitzgerald <rf@opensource.cirrus.com> says:
This series fixes two problems found in the probing process that
can cause a deadlock (patch #1) or a hang (patch #2) during
component_probe() until the wait for init_completion times out.
Link: https://patch.msgid.link/20260716132045.1469156-1-rf@opensource.cirrus.com
|
|
Pull kvm fixes from Paolo Bonzini:
"arm64:
- Fix an accounting buglet when reclaiming pages from a protected
guest
- Fix a bunch of architectural compliance issues when injecting a
synthesised exception, most of which were missing the PSTATE.IL bit
indicating a 32bit-wide instruction
- Another set of fixes addressing issues with translation of
VNCR_EL2, including corner cases where the guest point that
register at a RO page...
- Don't warn when trapping accesses to ZCR_EL2 from an L2 guest, as
that's not unexpected at all
- Address a bunch of races with LPI migration vs LPIs being disabled
- Fix a total howler of a bug combining FEAT_MOPS and NV, resulting
in exception returning in the wrong place...
- Move locking for kvm_io_bus_get_dev() into the caller, ensuring
race-free checks that the returned object is of the correct type
- Fix initialisation of the page-table walk level when relaxing
permissions
- Correctly update the XN attribute when relaxing permissions
- Fix the sign extension of loads from emulated MMIO regions
- Assorted collection of fixes for pKVM's FFA proxy, together with a
couple of FFA driver adjustments
- Coerce Fuad Tabba into a reviewer role, and may his Inbox catch
fire!
s390:
- more gmap KVM memory management fixes
- PCI passthru fixes
x86:
- Fix a bug where KVM will trigger a UAF if updating IOMMU IRTEs
fails when registering an IRQ-bypass producer
- Ignore pending PV EOI instead of BUG()ing the host if the feature
was disabled by the guest
- Fix nVMX bugs where KVM would run L1 with an L1-controlled CR3
after a failed "late" consistency check when KVM is NOT using EPT
- Disallow intra-host migration/mirroring of SNP VMs as KVM doesn't
yet support moving/mirroring SNP state
- Fix a TOCTOU bug in KVM's handling of the "trusted" CPUID for TDX
guests
- Fix a NULL pointer deref in trace_kvm_inj_exception() where a
change to the core infrastructure missed KVM's unique (ab)use of
__print_symbolic()
- Put vmcs12 pages if nested VM-Enter fails due to invalid guest
state
- Fix TLB conflicts between two VMs if one of them VM is run on a CPU
before and after it is hotplugged"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (48 commits)
KVM: SVM: Bump asid_generation on CPU online to avoid ASID collision after hotplug
KVM: nVMX: Put vmcs12 pages if nested VM-Enter fails due to invalid guest state
KVM: x86: Fix null pointer deref due to dummy array in trace_kvm_inj_exception()
KVM: TDX: Reject concurrent change to CPUID entry count
KVM: selftests: Verify SNP VMs are rejected from migration and mirroring
KVM: SEV: Do not allow intra-host migration/mirroring of SNP VMs
KVM: s390: pci: Fix handling of AIF enable without AISB
KVM: s390: Improve kvm_s390_vm_stop_migration()
KVM: s390: Fix dat_crste_walk_range() early return
KVM: s390: vsie: Avoid potential deadlock with real spaces
KVM: s390: pci: Fix GISC refcount leak on AIF enable failure
KVM: nVMX: Don't use vmcs01.GUEST_CR3 to snapshot L1's CR3 when EPT is disabled
KVM: nVMX: Move vTPR vs. TPR Threshold consistency check into "normal" checks
KVM: x86: Ignore pending PV EOI if the vCPU has since disabled PV EOIs
KVM: x86: Nullify irqfd->producer if updating IRTE for bypass fails
KVM: arm64: Fix propagation of TLBI level in kvm_pgtable_stage2_relax_perms()
firmware: arm_ffa: Fix Endpoint Memory Access Descriptor offset calculation
firmware: arm_ffa: Fix out-of-bound writes in ffa_setup_and_transmit()
KVM: arm64: Zero out the stack initialized data in the FFA handler
KVM: arm64: Ensure FFA ranges are page aligned
...
|
|
In cs35l56_init() use complete_all() to signal init_completion instead
of complete().
cs35l56_init() was signaling init_completion using the complete() function.
This only releases ONE waiter.
If cs35l56_component_probe() was called multiple times the first time
would consume that one signal, then future calls would timeout waiting for
the completion. This could happen if:
- The component is probed, removed, then probed again without the cs35l56
module being removed.
- A call to component_probe() returns an error and ASoC calls it again
later.
It should use complete_all() so that after it has been signaled it will
allow any code that waits on it to continue immediately.
The one case where the driver must wait for initialization to run again is
when waiting for a reboot after firmware download, and here the code
correctly calls reinit_completion() first.
Fixes: e496112529006 ("ASoC: cs35l56: Add driver for Cirrus Logic CS35L56")
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://patch.msgid.link/20260716132045.1469156-3-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
On I2C/SPI call cs35l56_init() before calling
snd_soc_register_component() to prevent the potential for a deadlock
on init_completion.
For most buses all the hardware would be ready when probe() returns,
but on SoundWire, probe() must return before the SoundWire bus driver
will enumerate the device. All access to the registers must be deferred
until the driver receives an ATTACHED notification. But anything that
could return -EPROBE_DEFER must be called during probe, and that includes
snd_soc_register_component(). Because of that, on SoundWire the ASoC
component can be created before the registers are accssible, so
cs35l56_component_probe() waits for init_completion to signal that the
registers are accessible.
On I2C/SPI this 2-stage startup isn't required so their probe()
functions simply called cs35l56_common_probe() and then cs35l56_init().
The problem with this was that snd_soc_register_component() was still
called early. If this triggered ASoC to create the card, ASoC would call
cs35l56_component_probe() which waits on init_completion - but this would
be running inside the cs35l56 driver probe() so blocking it from reaching
the code that signals init_completion, causing a deadlock.
Fixes: e496112529006 ("ASoC: cs35l56: Add driver for Cirrus Logic CS35L56")
Reported-by: Salman S. Tahir <salman.abusaad@gmail.com>
Closes: https://lore.kernel.org/linux-sound/95c21574-97d5-4311-9263-9e174d22d22c@opensource.cirrus.com/T/#u
Tested-by: Salman S. Tahir <salman.abusaad@gmail.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://patch.msgid.link/20260716132045.1469156-2-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/fixes
Renesas fixes for v7.2
- Fix lock-ups on the Ironhide development board.
* tag 'renesas-fixes-for-v7.2-tag1' of https://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
arm64: dts: renesas: ironhide: Describe inline ECC carveouts
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Locking is disabled in the regmap config as this driver uses its own
lock. This means that all calls to regmap functions (read or write) must
hold the i2c_lock. The function pca953x_irq_bus_sync_unlock() did not do
this, and it was therefore possible that multiple threads could cause an
incorrect register to be read/written.
A previous patch partly fixed this, but only protected the write to the
interrupt mask register, and not the read from the direction register.
Fixes: bfc6444b57dc ("gpio: pca953x: fix pca953x_irq_bus_sync_unlock race")
Cc: stable@vger.kernel.org
Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
Link: https://patch.msgid.link/20260709045116.2304246-1-mark.tomlinson@alliedtelesis.co.nz
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
|
|
NR_FIX_BTMAPS is the per-slot page limit for early_ioremap(). Since
__early_ioremap() maps the page-aligned physical range, a 256K request
can require one extra page when the physical address is not page-aligned.
Reserve one extra page per slot so the 256K mapping budget is usable
regardless of the initial page offset.
Link: https://lore.kernel.org/r/08fd96fa-ee3a-4904-bd11-bb08bd90436f@kylinos.cn
Signed-off-by: Yu Peng <pengyu@kylinos.cn>
Signed-off-by: Will Deacon <will@kernel.org>
|
|
__destroy_component_cfg() adds each RIS mbwu_state object to the MPAM
garbage list when destroying component configuration.
However, mbwu_state is allocated per RIS and only for RISes with MBWU
monitors. A component can therefore have comp->cfg allocated while some
RISes still have ris->mbwu_state set to NULL.
Passing a NULL mbwu_state to add_to_garbage() dereferences the NULL
pointer inside the macro.
Skip RISes that do not have an mbwu_state object before adding them to
the garbage list.
Fixes: 41e8a14950e1 ("arm_mpam: Track bandwidth counter state for power management")
Signed-off-by: Guangshuo Li <lgs201920130244@gmail.com>
Reviewed-by: Ben Horgan <ben.horgan@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
|
|
MPAMCFG_MBW_PBM is written from cfg if cfg has the MBW partition feature.
It is reset when cfg does not have the MBW partition feature.
But the register handling is reversed. This may cause an incorrect
register setting. For example, during an MPAM reset, reset_cfg is
empty (no MBW partition feature set), and cfg->mbw_pbm is 0. Instead of
resetting MPAMCFG_MBW_PBM to all 1's, the current logic will set it to
cfg->mbw_pbm, which is 0.
Fix the issue by swapping the if/else branches.
Fixes: a1cb6577f575 ("arm_mpam: Reset when feature configuration bit unset")
Reported-by: Matt Ochs <mochs@nvidia.com>
Signed-off-by: Fenghua Yu <fenghuay@nvidia.com>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Reviewed-by: Ben Horgan <ben.horgan@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Priority partitioning is not supported other than to set the per-PARTID
defaults in MPAMCFG_PRI, INTPRI and DSPRI, to the highest priority. When 0
is the lowest priority, all ones is the highest priority. However, these
values are calculated with an extra higher bit set.
Luckily, there is still no chance of setting functional bits incorrectly.
When the priority widths are maximal, this is ensured as the fields have
width 16 and a u16 holds the value for each field. When the widths are
smaller, the higher order bits beyond the advertised widths,
MPAMF_PRI_IDR.DSPRI_WD and MPAMF_PRI_IDR.INTPRI_WD, in the priority fields
INTPRI and DSPRI are not used to calculate the priority. It is not
specified whether these higher order bits are RAZ/WI or Res0 and so it is
desirable not to set them to avoid the chance of misleading reads.
Correct the priority reset values.
Fixes: 880df85d8673 ("arm_mpam: Probe and reset the rest of the features")
Signed-off-by: Ben Horgan <ben.horgan@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
|
|
When seccomp support was originally added to arm64 in a1ae65b21941
("arm64: add seccomp support"), seccomp was erroneously called _before_
the ptrace syscall-enter-stop and therefore the tracer could trivially
manipulate the syscall register state after the seccomp check had
passed. This was subsequently fixed in a5cd110cb836 ("arm64/ptrace: run
seccomp after ptrace") by moving the seccomp check after the tracer has
run. Unfortunately, a decade later, that fix has been reported to be
incomplete.
On arm64, both the first argument to a syscall and its eventual return
value are allocated to register x0. In order to facilitate syscall
restarting and querying of syscall arguments on the syscall exit path,
the original value of x0 is stashed in 'struct pt_regs::orig_x0' early
during the syscall entry path and is returned for the first argument by
syscall_get_arguments(). Unlike 32-bit Arm, this stashed value is not
directly exposed via ptrace() and so changes to register x0 made by the
tracer on a syscall-enter-stop are not reflected in 'orig_x0'. This
means that seccomp, syscall tracepoints and audit can observe a stale
value for the register compared to the argument that will be observed by
the actual syscall.
Re-sync 'orig_x0' from x0 on the syscall entry path following a
potential ptrace stop (i.e. PTRACE_EVENTMSG_SYSCALL_ENTRY or
SECCOMP_RET_TRACE). This behaviour is limited to native tasks (because
compat tasks expose 'orig_r0' to ptrace) where the syscall is not being
skipped (because x0 is updated to hold the return value of -ENOSYS in
that case).
Cc: Kees Cook <kees@kernel.org>
Cc: Jinjie Ruan <ruanjinjie@huawei.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: stable@vger.kernel.org
Reported-by: Yiqi Sun <sunyiqixm@gmail.com>
Link: https://lore.kernel.org/all/20260529065444.1336608-1-sunyiqixm@gmail.com/
Suggested-by: Catalin Marinas <catalin.marinas@arm.com>
Fixes: a5cd110cb836 ("arm64/ptrace: run seccomp after ptrace")
Reviewed-by: Jinjie Ruan <ruanjinjie@huawei.com>
Tested-by: Jinjie Ruan <ruanjinjie@huawei.com>
Signed-off-by: Will Deacon <will@kernel.org>
|
|
bio_iov_iter_align_down expects the "normal" biovec layout from vector 0,
while bio_iov_iter_bounce_read abuses vector 0 for a bounce buffer
allocation. Pass an explicit bvec to bio_iov_iter_align_down to deal
with this case to avoid a double unpin.
Additionally we need to free the folio if no bio_vec could be added,
and adjust the size of the first bio_vec that contains the bounce buffer
when the I/O size is aligned down.
Fixes: e7b8b3c5b2a6 ("block: align down bounces bios")
Reported-by: 0wnerD1ed <l7z@0b1t.tech>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: 0wnerD1ed <l7z@0b1t.tech>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Link: https://patch.msgid.link/20260716091306.316625-3-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
When CONFIG_PERSISTENT_HUGE_ZERO_FOLIO is enabled, iomap_dio_zero() can
add a huge zero folio to a zeroing bio, which needs special treatment
in bio_free_folios by also checking is_huge_zero_folio() in addition to
is_zero_folio().
Fixes: 8dd5e7c75d7b ("block: add helpers to bounce buffer an iov_iter into bios")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@kernel.org>
Link: https://patch.msgid.link/20260716091306.316625-2-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
When the per-CPU bio cache is enabled but empty, bio_alloc_percpu_cache()
returns NULL and bio_alloc_bioset() falls straight through to the mempool
fallback:
if (unlikely(!bio)) {
if (!(saved_gfp & __GFP_DIRECT_RECLAIM))
return NULL;
...
}
For non-sleeping allocations (no __GFP_DIRECT_RECLAIM) this returns NULL
without ever attempting a slab allocation, even when there is plenty of
free memory.
Commit b520c4eef83d ("block: split bio_alloc_bioset more clearly into a
fast and slowpath") introduced this. Before it, a percpu cache miss fell
through to mempool_alloc(), which attempted the underlying slab allocation
first and only failed when that slab allocation failed. The restructuring
dropped the slab attempt that non-sleeping callers of a cache-enabled
bioset (such as the default fs_bio_set used by bio_alloc()) relied on.
Try a slab allocation with optimistic GFP_ flags before falling back to
the mempool whenever the bio is still NULL, so both the cache-empty and
non-cache paths share the same slab attempt. This restores the previous
behavior for non-sleeping allocations.
Fixes: b520c4eef83d ("block: split bio_alloc_bioset more clearly into a fast and slowpath")
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Joseph Qi <joseph.qi@linux.alibaba.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://patch.msgid.link/20260709020145.4011533-1-joseph.qi@linux.alibaba.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Rules listed through the error_injection debugfs file omit the block
operation they match. As a result, rules that differ only in operation
are indistinguishable even though op is mandatory when adding a rule.
Signed-off-by: Jackie Liu <liuyun01@kylinos.cn>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://patch.msgid.link/20260715073341.95129-1-liu.yun@linux.dev
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
When elevator_change() is called concurrently for the same queue, the
elevator_change_done() function runs concurrently as well. This function
adds or deletes kobjects for the debugfs entry of the queue. Then the
concurrent calls cause memory corruption of the kobjects and result in a
process hang. The core part of the elevator switch is protected by queue
freeze and q->elevator_lock. However, since the commit 559dc11143eb
("block: move elv_register[unregister]_queue out of elevator_lock"), the
elevator_change_done() is not serialized. Hence the memory corruption
and the hang.
The failures are observed when udev-worker writes to a sysfs
queue/scheduler attribute file while the blktests test case block/005
writes to the same attribute file. The failure also can be recreated by
running two processes that write to the same queue/scheduler file
concurrently. The failure is observed since another commit 370ac285f23a
("block: avoid cpu_hotplug_lock depedency on freeze_lock"). This commit
changed the behavior of queue freeze and it unveiled the failure.
Fix the failure by changing elv_iosched_store() to acquire
update_nr_hwq_lock as the writer lock instead of the reader lock. This
serializes the whole elevator switch steps, including the
elevator_change_done() call.
Fixes: 559dc11143eb ("block: move elv_register[unregister]_queue out of elevator_lock")
Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Reviewed-by: Nilay Shroff <nilay@linux.ibm.com>
Reviewed-by: Ming Lei <tom.leiming@gmail.com>
Link: https://patch.msgid.link/20260716092237.1305030-1-shinichiro.kawasaki@wdc.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
bio_copy_kern() allocates pages that are normally freed by the bio
completion callback. If blk_rq_append_bio() rejects the bio, however,
blk_rq_map_kern() only drops the bio reference. Since bio_put() does not
free pages referenced by the bio vectors, those pages leak.
This can happen when the bio exceeds the queue segment constraints or
when a later mapping cannot be merged into a request built by earlier
calls. Track whether the buffer was copied and free those pages before
dropping the rejected bio.
Fixes: 3a5a39276d2a ("block: allow blk_rq_map_kern to append to requests")
Assisted-by: Codex:gpt-5.6-sol
Signed-off-by: Jackie Liu <liuyun01@kylinos.cn>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://patch.msgid.link/20260715073518.96042-1-liu.yun@linux.dev
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The fs210x driver currently puts the regmap cache into cache only mode
during suspend but at no point does it make it writable again, meaning
that device can't work after suspend other than basic powerup which
bypasses the cache.
Mark the cache as writable again when we resync the registers, it's not
clear to me that the cache only mode is needed at all but this is a
fairly minimal change. Since this is setting a flag it's safe to do
even if the cache was not previously in cache only mode.
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://patch.msgid.link/20260715-asoc-fs210x-fix-resume-v1-1-dd81d9c62c05@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Oliver Hartkopp <socketcan@hartkopp.net> says:
As sashiko-bot was not able to check the second patch this bundle is
re-posted with b4 preparation.
Link: https://patch.msgid.link/20260712-isotp-fixes-v10-0-793a1b1ce17f@hartkopp.net
[mkl: added stable@k.o on Cc, converted Link: -> Closes:]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The TX state machine (so->tx.state) is driven from three contexts:
sendmsg() claiming and progressing a transfer, the RX path consuming
Flow Control/echo frames, and two hrtimers timing out a stalled
transfer. Mixing a lock-free cmpxchg() claim in sendmsg() with
hrtimer_cancel() calls made under so->rx_lock elsewhere left windows
where a frame or timer callback could act on a state that had already
moved on, corrupting an unrelated transfer.
so->rx_lock now covers the full lifecycle of a TX claim: sendmsg()
takes it to check so->tx.state is ISOTP_IDLE, switch it to
ISOTP_SENDING, bump so->tx_gen and drain the previous transfer's
timers - all as one critical section. isotp_rcv_fc()/isotp_rcv_cf()
already run under this lock via isotp_rcv(), and isotp_rcv_echo() now
takes it itself, so none of them can ever observe a transfer mid-claim.
This also means a transfer can no longer be handed to sendmsg()'s
cleanup paths (signal or send error) while another thread is
concurrently claiming or finishing it, so those paths can cancel
timers and reset the state unconditionally.
isotp_release() claims the socket the same way, so a racing sendmsg()
sees a consistent ISOTP_SHUTDOWN and skips arming its timer or sending.
Only the hrtimer callbacks stay outside so->rx_lock, since they run
under so->rx_lock's cancellation elsewhere and taking it themselves
would deadlock. so->tx_gen lets them recognize whether the transfer
they timed out is still the one currently active, so they don't
report an error against a transfer that has since completed or been
superseded.
Fixes: e057dd3fc20f ("can: add ISO 15765-2:2016 transport protocol")
Reported-by: sashiko-bot@kernel.org
Closes: https://lore.kernel.org/linux-can/20260710142146.BDAE61F000E9@smtp.kernel.org/
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://patch.msgid.link/20260712-isotp-fixes-v10-3-793a1b1ce17f@hartkopp.net
Cc: stable@kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
