1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
|
# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
%YAML 1.2
---
$id: http://devicetree.org/schemas/input/microchip,cap11xx.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#
title: Microchip CAP11xx based capacitive touch sensors
description: |
The Microchip CAP1xxx Family of RightTouchTM multiple-channel capacitive
touch controllers and LED drivers. The device communication via I2C only.
For more product information please see the links below:
CAP1106: https://ww1.microchip.com/downloads/en/DeviceDoc/00001624B.pdf
CAP1114: https://ww1.microchip.com/downloads/en/DeviceDoc/00002444A.pdf
CAP1126: https://ww1.microchip.com/downloads/en/DeviceDoc/00001623B.pdf
CAP1188: https://ww1.microchip.com/downloads/en/DeviceDoc/00001620C.pdf
CAP1203: https://ww1.microchip.com/downloads/en/DeviceDoc/00001572B.pdf
CAP1206: https://ww1.microchip.com/downloads/en/DeviceDoc/00001567B.pdf
CAP1293: https://ww1.microchip.com/downloads/en/DeviceDoc/00001566B.pdf
CAP1298: https://ww1.microchip.com/downloads/en/DeviceDoc/00001571B.pdf
maintainers:
- Rob Herring <robh@kernel.org>
properties:
compatible:
enum:
- microchip,cap1106
- microchip,cap1114
- microchip,cap1126
- microchip,cap1188
- microchip,cap1203
- microchip,cap1206
- microchip,cap1293
- microchip,cap1298
reg:
maxItems: 1
'#address-cells':
const: 1
'#size-cells':
const: 0
interrupts:
maxItems: 1
description: |
Property describing the interrupt line the
device's ALERT#/CM_IRQ# pin is connected to.
The device only has one interrupt source.
reset-gpios:
description: |
GPIO connected to the active-high RESET pin of the chip;
driving it high asserts reset and deep sleep, while driving
it low releases reset for normal operation.
maxItems: 1
autorepeat:
description: |
Enables the Linux input system's autorepeat feature on the input device.
linux,keycodes:
minItems: 3
maxItems: 14
description: |
Specifies an array of numeric keycode values to
be used for the channels. If this property is
omitted, KEY_A, KEY_B, etc are used as defaults.
The number of entries must correspond to the number of channels.
microchip,sensor-gain:
$ref: /schemas/types.yaml#/definitions/uint32
default: 1
enum: [1, 2, 4, 8]
description: |
Defines the gain of the sensor circuitry. This
effectively controls the sensitivity, as a
smaller delta capacitance is required to
generate the same delta count values.
microchip,irq-active-high:
type: boolean
description: |
By default the interrupt pin is active low
open drain. This property allows using the active
high push-pull output.
microchip,sensitivity-delta-sense:
$ref: /schemas/types.yaml#/definitions/uint32
default: 32
enum: [1, 2, 4, 8, 16, 32, 64, 128]
description:
Controls the sensitivity multiplier of a touch detection.
Higher value means more sensitive settings.
At the more sensitive settings, touches are detected for a smaller delta
capacitance corresponding to a "lighter" touch.
microchip,signal-guard:
$ref: /schemas/types.yaml#/definitions/uint32-array
minItems: 3
maxItems: 8
items:
enum: [0, 1]
description: |
0 - off
1 - on
The signal guard isolates the signal from virtual grounds.
If enabled then the behavior of the channel is changed to signal guard.
The number of entries must correspond to the number of channels.
microchip,input-threshold:
$ref: /schemas/types.yaml#/definitions/uint32-array
minItems: 3
maxItems: 8
items:
minimum: 0
maximum: 127
description:
Specifies the delta threshold that is used to determine if a touch has
been detected. A higher value means a larger difference in capacitance
is required for a touch to be registered, making the touch sensor less
sensitive.
The number of entries must correspond to the number of channels.
CAP1114 is an exception where channels 8~14 reuse the eighth entry's
threshold, so counts differ.
microchip,calib-sensitivity:
$ref: /schemas/types.yaml#/definitions/uint32-array
minItems: 3
maxItems: 8
items:
enum: [1, 2, 4]
description: |
Specifies an array of numeric values that controls the gain
used by the calibration routine to enable sensor inputs
to be more sensitive for proximity detection.
Gain is based on touch pad capacitance range
1 - 5-50pF
2 - 0-25pF
4 - 0-12.5pF
The number of entries must correspond to the number of channels.
patternProperties:
"^led@[0-9a]$":
type: object
description: CAP11xx LEDs
$ref: /schemas/leds/common.yaml#
properties:
reg:
description: LED channel number
minimum: 0
maximum: 10
label: true
linux,default-trigger: true
default-state: true
required:
- reg
additionalProperties: false
allOf:
- $ref: input.yaml
- if:
properties:
compatible:
contains:
enum:
- microchip,cap1106
- microchip,cap1203
- microchip,cap1206
- microchip,cap1293
- microchip,cap1298
then:
properties:
reset-gpios: false
- if:
properties:
compatible:
contains:
enum:
- microchip,cap1114
then:
properties:
linux,keycodes:
minItems: 14
else:
properties:
linux,keycodes:
maxItems: 8
- if:
properties:
compatible:
contains:
enum:
- microchip,cap1106
- microchip,cap1203
- microchip,cap1206
- microchip,cap1293
- microchip,cap1298
then:
patternProperties:
"^led@": false
- if:
properties:
compatible:
contains:
enum:
- microchip,cap1126
then:
patternProperties:
"^led@":
properties:
reg:
maximum: 1
- if:
properties:
compatible:
contains:
enum:
- microchip,cap1188
then:
patternProperties:
"^led@":
properties:
reg:
maximum: 7
- if:
properties:
compatible:
contains:
enum:
- microchip,cap1106
- microchip,cap1114
- microchip,cap1126
- microchip,cap1188
- microchip,cap1203
- microchip,cap1206
then:
properties:
microchip,signal-guard: false
microchip,calib-sensitivity: false
required:
- compatible
- interrupts
additionalProperties: false
examples:
- |
#include <dt-bindings/gpio/gpio.h>
i2c {
#address-cells = <1>;
#size-cells = <0>;
touch@28 {
compatible = "microchip,cap1188";
interrupt-parent = <&gpio1>;
interrupts = <0 0>;
reg = <0x28>;
autorepeat;
microchip,sensor-gain = <2>;
microchip,sensitivity-delta-sense = <16>;
microchip,input-threshold = <21>, <18>, <46>, <46>, <46>, <21>;
linux,keycodes = <103>, /* KEY_UP */
<106>, /* KEY_RIGHT */
<108>, /* KEY_DOWN */
<105>, /* KEY_LEFT */
<109>, /* KEY_PAGEDOWN */
<104>; /* KEY_PAGEUP */
reset-gpios = <&gpio 17 GPIO_ACTIVE_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
led@0 {
label = "cap11xx:green:usr0";
reg = <0>;
};
led@1 {
label = "cap11xx:green:usr1";
reg = <1>;
};
led@2 {
label = "cap11xx:green:alive";
reg = <2>;
linux,default-trigger = "heartbeat";
};
};
};
|
