| Age | Commit message (Collapse) | Author |
|---|
|
In the CCM B0 block the message-length field Q spans L bytes, where
L (cl in the driver) is derived from the cipher IV flags byte as
c_ivin[0] + 1. set_aead_auth_iv() hardcoded writing only the last 2
bytes of a_ivin with cryptlen, implicitly assuming cl = 2.
When cl = 3 (a shorter nonce yielding a 3-byte length field) and the
packet is longer than 65535 bytes, cryptlen no longer fits in 2 bytes.
The dropped high byte made the auth IV built by the driver differ from
the one consumed by the hardware, so the software/hardware comparison
failed and the CCM request errored out.
Write the last cl bytes of a_ivin in a loop driven by the IV's CL
value, so the length-field width always matches the algorithm
configuration instead of assuming a fixed 2-byte field.
Fixes: c16a70c1f253 ("crypto: hisilicon/sec - add new algorithm mode for AEAD")
Signed-off-by: Zhushuai Yin <yinzhushuai@huawei.com>
Signed-off-by: Chenghai Huang <huangchenghai2@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
hlf_q_num is set but never read; drop the field and its assignment.
Signed-off-by: Chenghai Huang <huangchenghai2@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
sec_create_qp_ctx() reads ctx->type_supported to pick its callback, but
sec_skcipher_init() and sec_aead_init() set it after sec_ctx_base_init()
has already walked the qp_ctx loop, so the value is uninitialized when
first consumed. Set type_supported in sec_ctx_base_init() before the
loop; the alg init paths now just select req_op from it.
Signed-off-by: Chenghai Huang <huangchenghai2@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Each bit in the error interrupt register corresponds to a specific
error type. A bit value of 0 enables the interrupt, and a bit value
of 1 disables the interrupt. Currently, when disabling interrupts,
it incorrectly enables the interrupt types that were not enabled.
Therefore, when disabling interrupts, all bits should be directly
written to 1.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Zongyu Wu <wuzongyu1@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The problem that the VF device cannot obtain the isolation
status and isolation threshold of the device is resolved.
The accelerator driver can query the device isolation status
and threshold via the VF device using the fault query sysfs
interface under uacce. Note that only the PF device supports
isolation policy configuration, while the VF device is
limited to read-only query operations.
Signed-off-by: Zhushuai Yin <yinzhushuai@huawei.com>
Signed-off-by: Zongyu Wu <wuzongyu1@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Lower the priority of HiSilicon's crypto implementations to allow more
suitable alternatives to be selected. For example, certain kernel
use-cases do not benefit from HiSilicon's symmetric crypto algorithms.
This change ensures that more appropriate options are chosen first while
retaining HiSilicon's implementations as alternatives.
Signed-off-by: lizhi <lizhi206@huawei.com>
Signed-off-by: Chenghai Huang <huangchenghai2@huawei.com>
Reviewed-by: Longfang Liu <liulongfang@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
- sec_register_to_crypto() and sec_unregister_from_crypto()
have been removed, the function declarations have not been
removed. Remove them.
- hisi_qm_start_qp and hisi_qm_stop_qp are called internally by the
QM. Therefore, the EXPORT_SYMBOL_GPL declaration of these
non-public interfaces is deleted.
Signed-off-by: Chenghai Huang <huangchenghai2@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
1. The return value val of sec_debugfs_atomic64_get is of the
u64 type, but %lld instead of %llu is used in DEFINE_DEBUGFS_ATTRIBUTE.
Fix it.
2. In debugfs.c, since the types of q_depth and xeq_depth are u16,
the results of q_depth - 1 and xeq_depth - 1 are int rather than
u16. Use %d for int.
Signed-off-by: Zhushuai Yin <yinzhushuai@huawei.com>
Signed-off-by: Chenghai Huang <huangchenghai2@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
During packet transmission, if the system is under heavy load,
the hardware might complete processing the packet and free the
request memory (req) before the transmission function finishes.
If the software subsequently accesses this req, a use-after-free
error will occur. The qp_ctx memory exists throughout the packet
sending process, so replace the req with the qp_ctx.
Fixes: f0ae287c5045 ("crypto: hisilicon/sec2 - implement full backlog mode for sec")
Signed-off-by: Wenkai Lin <linwenkai6@hisilicon.com>
Signed-off-by: Chenghai Huang <huangchenghai2@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The accelerator device supports usage statistics. This patch enables
obtaining the accelerator's usage through the "dev_usage" file.
The returned number expressed as a percentage as a percentage.
Signed-off-by: Zongyu Wu <wuzongyu1@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
This converts some of the visually simpler cases that have been split
over multiple lines. I only did the ones that are easy to verify the
resulting diff by having just that final GFP_KERNEL argument on the next
line.
Somebody should probably do a proper coccinelle script for this, but for
me the trivial script actually resulted in an assertion failure in the
middle of the script. I probably had made it a bit _too_ trivial.
So after fighting that far a while I decided to just do some of the
syntactically simpler cases with variations of the previous 'sed'
scripts.
The more syntactically complex multi-line cases would mostly really want
whitespace cleanup anyway.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This was done entirely with mindless brute force, using
git grep -l '\<k[vmz]*alloc_objs*(.*, GFP_KERNEL)' |
xargs sed -i 's/\(alloc_objs*(.*\), GFP_KERNEL)/\1)/'
to convert the new alloc_obj() users that had a simple GFP_KERNEL
argument to just drop that argument.
Note that due to the extreme simplicity of the scripting, any slightly
more complex cases spread over multiple lines would not be triggered:
they definitely exist, but this covers the vast bulk of the cases, and
the resulting diff is also then easier to check automatically.
For the same reason the 'flex' versions will be done as a separate
conversion.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This is the result of running the Coccinelle script from
scripts/coccinelle/api/kmalloc_objs.cocci. The script is designed to
avoid scalar types (which need careful case-by-case checking), and
instead replace kmalloc-family calls that allocate struct or union
object instances:
Single allocations: kmalloc(sizeof(TYPE), ...)
are replaced with: kmalloc_obj(TYPE, ...)
Array allocations: kmalloc_array(COUNT, sizeof(TYPE), ...)
are replaced with: kmalloc_objs(TYPE, COUNT, ...)
Flex array allocations: kmalloc(struct_size(PTR, FAM, COUNT), ...)
are replaced with: kmalloc_flex(*PTR, FAM, COUNT, ...)
(where TYPE may also be *VAR)
The resulting allocations no longer return "void *", instead returning
"TYPE *".
Signed-off-by: Kees Cook <kees@kernel.org>
|
|
unavailable
When all hardware queues are busy and no shareable queue,
new processes fail to apply for queues. To avoid affecting
tasks, support fallback mechanism when hardware queues are
unavailable.
Fixes: c16a70c1f253 ("crypto: hisilicon/sec - add new algorithm mode for AEAD")
Signed-off-by: Qi Tao <taoqi10@huawei.com>
Signed-off-by: Chenghai Huang <huangchenghai2@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Consolidate the creation and start of qp into the function
hisi_qm_alloc_qps_node. This change eliminates the need for
each module to perform these steps in two separate phases
(creation and start).
Signed-off-by: Chenghai Huang <huangchenghai2@huawei.com>
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Originally, when a queue was requested, it could only be configured
with the default algorithm type of 0. Now, when multiple tfms use
the same queue, the queue must be selected based on its attributes
to meet the requirements of tfm tasks. So the algorithm type
attribute of queue need to be distinguished. Just like a queue used
for compression in ZIP cannot be used for decompression tasks.
Fixes: 3f1ec97aacf1 ("crypto: hisilicon/qm - Put device finding logic into QM")
Signed-off-by: Chenghai Huang <huangchenghai2@huawei.com>
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
for callback
When multiple tfm use a same qp, the backlog data should be managed
centrally by the qp, rather than in the qp_ctx of each req.
Additionally, since SEC_BD_TYPE1 and SEC_BD_TYPE2 cannot use the
tag of the sqe to carry the virtual address of the req, the sent
sqe is stored in the qp. This allows the callback function to get
the req address. To handle the differences between hardware types,
the callback functions are split into two separate implementations.
Fixes: f0ae287c5045 ("crypto: hisilicon/sec2 - implement full backlog mode for sec")
Signed-off-by: Chenghai Huang <huangchenghai2@huawei.com>
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
When an error occurs on the device, an interrupt is reported.
When the firmware forwards the interrupt to the driver and masks the
error. If the driver does not enable error reporting when an error does
not need to be reset, the device does not report the error to the driver
when the error occurs again. Therefore, after the driver obtains the
information, the error reporting needs to be enabled again.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Chenghai Huang <huangchenghai2@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
After the device memory is cleared, if the software sends
the doorbell operation, the hardware may trigger a axi error
when processing the doorbell. This error is caused by memory
clearing and hardware access to address 0. Therefore, the axi
error is masked during this period.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Chenghai Huang <huangchenghai2@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Fix the false-positive warning of qp_ctx being unitialised in
sec_request_init. The value of ctx_q_num defaults to 2 and is
guaranteed to be non-zero.
Thus qp_ctx is always initialised. However, the compiler is
not aware of this constraint on ctx_q_num. Restructure the loop
so that it is obvious to the compiler that ctx_q_num cannot be
zero.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Reviewed-by: Longfang Liu <liulongfang@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
As noted in the kernel documentation [1], open-coded multiplication in
allocator arguments is discouraged because it can lead to integer overflow.
Use devm_kcalloc() to gain built-in overflow protection, making memory
allocation safer when calculating allocation size compared to explicit
multiplication.
Link: https://www.kernel.org/doc/html/next/process/deprecated.html#open-coded-arithmetic-in-allocator-arguments #1
Signed-off-by: Qianfeng Rong <rongqianfeng@vivo.com>
Reviewed-by: Longfang Liu <liulongfang@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
address prefetch
After enabling address prefetch, check the sva module status. If all
previous prefetch requests from the sva module are not completed, then
disable the address prefetch to ensure normal execution of new task
operations. After disabling address prefetch, check if all requests
from the sva module have been completed.
Fixes: a5c164b195a8 ("crypto: hisilicon/qm - support address prefetching")
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Chenghai Huang <huangchenghai2@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
When the device resumes from a suspended state, it will revert to its
initial state and requires re-enabling. Currently, the address prefetch
function is not re-enabled after device resuming. Move the address prefetch
enable to the initialization process. In this way, the address prefetch
can be enabled when the device resumes by calling the initialization
process.
Fixes: 607c191b371d ("crypto: hisilicon - support runtime PM for accelerator device")
Signed-off-by: Chenghai Huang <huangchenghai2@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
This patch introduces a hierarchical backlog mechanism to cache
user data in high-throughput encryption/decryption scenarios,
the implementation addresses packet loss issues when hardware
queues overflow during peak loads.
First, we use sec_alloc_req_id to obtain an exclusive resource
from the pre-allocated resource pool of each queue, if no resource
is allocated, perform the DMA map operation on the request memory.
When the task is ready, we will attempt to send it to the hardware,
if the hardware queue is already full, we cache the request into
the backlog list, then return an EBUSY status to the upper layer
and instruct the packet-sending thread to pause transmission.
Simultaneously, when the hardware completes a task, it triggers
the sec callback function, within this function, reattempt to send
the requests from the backlog list and wake up the sending thread
until the hardware queue becomes fully occupied again.
In addition, it handles such exceptions like the hardware is reset
when packets are sent, it will switch to the software computing
and release occupied resources.
Signed-off-by: Wenkai Lin <linwenkai6@hisilicon.com>
Signed-off-by: Chenghai Huang <huangchenghai2@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The following splat was triggered when booting the kernel built with
arm64's defconfig + CRYPTO_SELFTESTS + DMA_API_DEBUG.
------------[ cut here ]------------
DMA-API: hisi_sec2 0000:75:00.0: cacheline tracking EEXIST, overlapping mappings aren't supported
WARNING: CPU: 24 PID: 1273 at kernel/dma/debug.c:596 add_dma_entry+0x248/0x308
Call trace:
add_dma_entry+0x248/0x308 (P)
debug_dma_map_sg+0x208/0x3e4
__dma_map_sg_attrs+0xbc/0x118
dma_map_sg_attrs+0x10/0x24
hisi_acc_sg_buf_map_to_hw_sgl+0x80/0x218 [hisi_qm]
sec_cipher_map+0xc4/0x338 [hisi_sec2]
sec_aead_sgl_map+0x18/0x24 [hisi_sec2]
sec_process+0xb8/0x36c [hisi_sec2]
sec_aead_crypto+0xe4/0x264 [hisi_sec2]
sec_aead_encrypt+0x14/0x20 [hisi_sec2]
crypto_aead_encrypt+0x24/0x38
test_aead_vec_cfg+0x480/0x7e4
test_aead_vec+0x84/0x1b8
alg_test_aead+0xc0/0x498
alg_test.part.0+0x518/0x524
alg_test+0x20/0x64
cryptomgr_test+0x24/0x44
kthread+0x130/0x1fc
ret_from_fork+0x10/0x20
---[ end trace 0000000000000000 ]---
DMA-API: Mapped at:
debug_dma_map_sg+0x234/0x3e4
__dma_map_sg_attrs+0xbc/0x118
dma_map_sg_attrs+0x10/0x24
hisi_acc_sg_buf_map_to_hw_sgl+0x80/0x218 [hisi_qm]
sec_cipher_map+0xc4/0x338 [hisi_sec2]
This occurs in selftests where the input and the output scatterlist point
to the same underlying memory (e.g., when tested with INPLACE_TWO_SGLISTS
mode).
The problem is that the hisi_sec2 driver maps these two different
scatterlists using the DMA_BIDIRECTIONAL flag which leads to overlapped
write mappings which are not supported by the DMA layer.
Fix it by using the fine grained and correct DMA mapping directions. While
at it, switch the DMA directions used by the hisi_zip driver too.
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Reviewed-by: Longfang Liu <liulongfang@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
During encryption and decryption, user requests
must be checked first, if the specifications that
are not supported by the hardware are used, the
software computing is used for processing.
Fixes: 2f072d75d1ab ("crypto: hisilicon - Add aead support on SEC2")
Signed-off-by: Wenkai Lin <linwenkai6@hisilicon.com>
Signed-off-by: Chenghai Huang <huangchenghai2@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The hardware only supports authentication sizes
that are 4-byte aligned. Therefore, the driver
switches to software computation in this case.
Fixes: 2f072d75d1ab ("crypto: hisilicon - Add aead support on SEC2")
Signed-off-by: Wenkai Lin <linwenkai6@hisilicon.com>
Signed-off-by: Chenghai Huang <huangchenghai2@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
According to the HMAC RFC, the authentication key
can be 0 bytes, and the hardware can handle this
scenario. Therefore, remove the incorrect validation
for this case.
Fixes: 2f072d75d1ab ("crypto: hisilicon - Add aead support on SEC2")
Signed-off-by: Wenkai Lin <linwenkai6@hisilicon.com>
Signed-off-by: Chenghai Huang <huangchenghai2@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
On the HiSilicon accelerators drivers, the PF/VFs driver can send messages
to the VFs/PF by writing hardware registers, and the VFs/PF driver receives
messages from the PF/VFs by reading hardware registers. To support this
feature, a new version id is added, different communication mechanism are
used based on different version id.
Signed-off-by: Yang Shen <shenyang39@huawei.com>
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
When the digest alg is HMAC-SHAx or another, the authsize may be less
than 4 bytes and mac_len of the BD is set to zero, the hardware considers
it a BD configuration error and reports a ras error, so the sec driver
needs to switch to software calculation in this case, this patch add a
check for it and remove unnecessary check that has been done by crypto.
Fixes: 2f072d75d1ab ("crypto: hisilicon - Add aead support on SEC2")
Signed-off-by: Wenkai Lin <linwenkai6@hisilicon.com>
Signed-off-by: Chenghai Huang <huangchenghai2@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
When the AEAD algorithm is used for encryption or decryption,
the input authentication length varies, the hardware needs to
obtain the input length to pass the integrity check verification.
Currently, the driver uses a fixed authentication length,which
causes decryption failure, so the length configuration is modified.
In addition, the step of setting the auth length is unnecessary,
so it was deleted from the setkey function.
Fixes: 2f072d75d1ab ("crypto: hisilicon - Add aead support on SEC2")
Signed-off-by: Wenkai Lin <linwenkai6@hisilicon.com>
Signed-off-by: Chenghai Huang <huangchenghai2@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The error detection of the data aggregation feature is separated from
the compression/decompression feature. This patch enables the error
detection and reporting of the data aggregation feature. When an
unrecoverable error occurs in the algorithm core, the device reports
the error to the driver, and the driver will reset the device.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
If an error indicating that the device needs to be reset is reported,
disable the error reporting before device reset is complete,
enable the error reporting after the reset is complete to prevent
the same error from being reported repeatedly.
Fixes: eaebf4c3b103 ("crypto: hisilicon - Unify hardware error init/uninit into QM")
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Query the capability register status of accelerator devices
(SEC, HPRE and ZIP) through the debugfs interface, for example:
cat cap_regs. The purpose is to improve the robustness and
locability of hardware devices and drivers.
Signed-off-by: Qi Tao <taoqi10@huawei.com>
Signed-off-by: Chenghai Huang <huangchenghai2@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Ensure that the inline function contains no more than 10 lines.
move q_num_set() from hisi_acc_qm.h to qm.c.
Signed-off-by: Chenghai Huang <huangchenghai2@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Before the device is enabled again, the device may still
store the previously processed data. If an error occurs in
the previous task, the device may fail to be enabled again.
Therefore, before enabling device, reset the device to restore
the initial state.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The offset of SEC_CORE_ENABLE_BITMAP should be 0 instead of 32,
it cause a kasan shift-out-bounds warning, fix it.
Signed-off-by: Wenkai Lin <linwenkai6@hisilicon.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Some information showed by the dump function is invalid. Mask
the unnecessary information from the dump file.
Signed-off-by: Chenghai Huang <huangchenghai2@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The AIV is one of the SEC resources. When releasing resources,
it need to release the AIV resources at the same time.
Otherwise, memory leakage occurs.
The aiv resource release is added to the sec resource release
function.
Signed-off-by: Chenghai Huang <huangchenghai2@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
There is a scenario where the file directory is created but the
file memory is not set. In this case, if a user accesses the
file, an error occurs.
So during the creation process of debugfs, memory should be
allocated first before creating the directory. In the release
process, the directory should be deleted first before releasing
the memory to avoid the situation where the memory does not
exist when accessing the directory.
In addition, the directory released by the debugfs is a global
variable. When the debugfs of an accelerator fails to be
initialized, releasing the directory of the global variable
affects the debugfs initialization of other accelerators.
The debugfs root directory released by debugfs init should be a
member of qm, not a global variable.
Signed-off-by: Chenghai Huang <huangchenghai2@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
When CONFIG_PCI_IOV is disabled, the SRIOV configuration
function is not required. An error occurs if this function is
incorrectly called.
Consistent with other modules, add the condition for
configuring the sriov function of sec_pci_driver.
Signed-off-by: Chenghai Huang <huangchenghai2@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Unused parameter of static functions should be removed.
Signed-off-by: Wenkai Lin <linwenkai6@hisilicon.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
This patch fixes following cleanup issues:
- The return value of the function is
inconsistent with the actual return type.
- After the pointer type is directly converted
to the `__le64` type, the program may crash
or produce unexpected results.
Signed-off-by: Qi Tao <taoqi10@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Nested macros are integrated into a single macro,
making the code simpler.
Signed-off-by: Qi Tao <taoqi10@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
As the sec DFX function is enhanced, some RAS registers are added
to the original DFX registers to enhance the DFX positioning function.
Signed-off-by: Qi Tao <taoqi10@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Switch to raw_smp_processor_id() to prevent a number of
warnings from kernel debugging. We do not care about
preemption here, as the CPU number is only used as a
poor mans load balancing or device selection. If preemption
happens during an encrypt/decrypt operation a small performance
hit will occur but everything will continue to work, so just
ignore it. This commit is similar to e7a9b05ca4
("crypto: cavium - Fix smp_processor_id() warnings").
[ 7538.874350] BUG: using smp_processor_id() in preemptible [00000000] code: af_alg06/8438
[ 7538.874368] caller is debug_smp_processor_id+0x1c/0x28
[ 7538.874373] CPU: 50 PID: 8438 Comm: af_alg06 Kdump: loaded Not tainted 5.10.0.pc+ #18
[ 7538.874377] Call trace:
[ 7538.874387] dump_backtrace+0x0/0x210
[ 7538.874389] show_stack+0x2c/0x38
[ 7538.874392] dump_stack+0x110/0x164
[ 7538.874394] check_preemption_disabled+0xf4/0x108
[ 7538.874396] debug_smp_processor_id+0x1c/0x28
[ 7538.874406] sec_create_qps+0x24/0xe8 [hisi_sec2]
[ 7538.874408] sec_ctx_base_init+0x20/0x4d8 [hisi_sec2]
[ 7538.874411] sec_aead_ctx_init+0x68/0x180 [hisi_sec2]
[ 7538.874413] sec_aead_sha256_ctx_init+0x28/0x38 [hisi_sec2]
[ 7538.874421] crypto_aead_init_tfm+0x54/0x68
[ 7538.874423] crypto_create_tfm_node+0x6c/0x110
[ 7538.874424] crypto_alloc_tfm_node+0x74/0x288
[ 7538.874426] crypto_alloc_aead+0x40/0x50
[ 7538.874431] aead_bind+0x50/0xd0
[ 7538.874433] alg_bind+0x94/0x148
[ 7538.874439] __sys_bind+0x98/0x118
[ 7538.874441] __arm64_sys_bind+0x28/0x38
[ 7538.874445] do_el0_svc+0x88/0x258
[ 7538.874447] el0_svc+0x1c/0x28
[ 7538.874449] el0_sync_handler+0x8c/0xb8
[ 7538.874452] el0_sync+0x148/0x180
Signed-off-by: Wenkai Lin <linwenkai6@hisilicon.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Add the printf of an error message and optimized the handling
process of ret.
Signed-off-by: Chenghai Huang <huangchenghai2@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Remove the unused CFB/OFB implementation.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Pre-store the valid value of the sec alg support related capability
register in sec_qm_init(), which will be called by probe process.
It can reduce the number of capability register queries and avoid
obtaining incorrect values in abnormal scenarios, such as reset
failed and the memory space disabled.
Fixes: 921715b6b782 ("crypto: hisilicon/sec - get algorithm bitmap from registers")
Signed-off-by: Zhiqi Song <songzhiqi1@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Extract a public function to set qm algs and remove
the similar code for setting qm algs in each module.
Signed-off-by: Wenkai Lin <linwenkai6@hisilicon.com>
Signed-off-by: Hao Fang <fanghao11@huawei.com>
Signed-off-by: Zhiqi Song <songzhiqi1@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
