| Age | Commit message (Collapse) | Author |
|---|
|
Kernel logs are filled with "DMA mask not set" messages for every
sub-device. The device does not use DMA for communication, so these
messages are useless. Disable the coherent DMA mask for the PMIC device,
which is also propagated to sub-devices.
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Link: https://patch.msgid.link/20260516-s2mu005-pmic-v7-5-73f9702fb461@disroot.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Samsung's S2MU005 PMIC includes subdevices for a charger, an MUIC (Micro
USB Interface Controller), and flash and RGB LED controllers.
S2MU005's interrupt registers divided into three domains, each for the
charger, flash LEDs, and the MUIC, packed into a single regmap IRQ chip
construct.
In devices other than S2MPG1X, the revision can be retrieved from the
first register of the PMIC regmap. In S2MU005 however, the location is
in offset 0x73. Introduce a switch-case block to allow selecting the
REG_ID register. S2MU005 also has a field mask for the revision. Apply
it using FIELD_GET() and get the extracted value.
Add initial support for S2MU005 in the PMIC driver, along with its three
interrupt chips, and support for allowing to fetch revision based on the
device variant.
Co-developed-by: Łukasz Lebiedziński <kernel@lvkasz.us>
Signed-off-by: Łukasz Lebiedziński <kernel@lvkasz.us>
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Link: https://patch.msgid.link/20260516-s2mu005-pmic-v7-4-73f9702fb461@disroot.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Add support for Samsung's S2MPG11 PMIC, which is a Power Management IC
for mobile applications with buck converters, various LDOs, power
meters, NTC thermistor inputs, and additional GPIO interfaces. It
typically complements an S2MPG10 PMIC in a main/sub configuration as
the sub-PMIC.
Like S2MPG10, communication is not via I2C, but via the Samsung ACPM
firmware.
While at it, we can also switch to asynchronous probe, which helps with
probe performance, as the drivers for s2mpg10 and s2mpg11 can probe in
parallel.
Note: The firmware uses the ACPM channel ID and the Speedy channel ID
to select the PMIC address. Since these are firmware properties, they
can not be retrieved from DT, but instead are deducted from the
compatible for now.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Link: https://patch.msgid.link/20260122-s2mpg1x-regulators-v7-9-3b1f9831fffd@linaro.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
This was used only to allow the s5m RTC driver to deal with the alarm
IRQ. That driver now uses a different approach to acquire that IRQ, and
::irq_data doesn't need to be kept around anymore.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Link: https://patch.msgid.link/20260113-s5m-alarm-v3-3-855a19db1277@linaro.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
By adding the RTC alarm IRQ to the MFD cell as a resource, the child
driver (rtc) can simply query that IRQ, instead of having a lookup
table itself.
This change therefore allows the child driver to be simplified with
regards to determining the alarm IRQ.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Link: https://patch.msgid.link/20260113-s5m-alarm-v3-1-855a19db1277@linaro.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Add myself as module author, so people know whom to complain to about
after the recent updates.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Link: https://lore.kernel.org/r/20250409-s2mpg10-v4-23-d66d5f39b6bf@linaro.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Use MFD_CELL macro helpers instead of open coding. This makes the code
a bit shorter and more obvious.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Link: https://lore.kernel.org/r/20250409-s2mpg10-v4-21-d66d5f39b6bf@linaro.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Using sizeof(*var) is generally preferred over using the size of its
open-coded type when allocating memory.
This helps avoiding bugs when the variable type changes but the memory
allocation isn't updated, and it simplifies renaming of the struct if
ever necessary.
No functional change.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Link: https://lore.kernel.org/r/20250409-s2mpg10-v4-20-d66d5f39b6bf@linaro.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Follow general style and use if (!arg) instead of comparing against
NULL.
While at it, drop a useless init in sec-irq.c.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Link: https://lore.kernel.org/r/20250409-s2mpg10-v4-19-d66d5f39b6bf@linaro.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Now that sec-i2c doesn't match device type by pointer casting anymore,
we can switch the device type from unsigned long to int easily.
This saves a few bytes in struct sec_pmic_dev due to member alignment.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Link: https://lore.kernel.org/r/20250409-s2mpg10-v4-18-d66d5f39b6bf@linaro.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
sec_irq_init() can fail, we shouldn't continue and ignore the error in
that case, but actually error out.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Link: https://lore.kernel.org/r/20250409-s2mpg10-v4-16-d66d5f39b6bf@linaro.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
dev_err_probe() exists to simplify code and harmonise error messages,
there's no reason not to use it here.
While at it, harmonise some error messages.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Link: https://lore.kernel.org/r/20250409-s2mpg10-v4-13-d66d5f39b6bf@linaro.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Rectify a couple of alignment problems reported by Checkpatch.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Link: https://lore.kernel.org/r/20250409-s2mpg10-v4-11-d66d5f39b6bf@linaro.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
There is no reason to have these two kernel modules separate. Having
them merged into one kernel module also slightly reduces memory
consumption and module load times a little.
mapped size (lsmod):
before: after:
sec_core 20480 sec_core 24576
sec_irq 16384
----------------
total 36864
Section sizes (size -A):
before: after:
sec_core 6780 sec_core 13239
sec_irq 8046
----------------
Total 14826
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Link: https://lore.kernel.org/r/20250409-s2mpg10-v4-10-d66d5f39b6bf@linaro.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
