| Age | Commit message (Collapse) | Author |
|---|
|
Commit 28f240683871 ("pinctrl: meson: mark the GPIO controller as
sleeping") set gpio_chip.can_sleep = true to work around
gpio-shared-proxy holding a spinlock across a sleeping pinctrl config
path. That locking bug is now fixed in the shared-proxy itself ("gpio:
shared-proxy: always serialize with a sleeping mutex"), so the
controller-wide workaround is no longer needed; the meson GPIO
controller does not sleep.
meson_gpio_get/set/direction_* access MMIO through regmap. The
regmap_mmio bus uses fast I/O (spinlock) locking, so these value
callbacks do not contain sleeping operations. Since gpio_chip.can_sleep
describes the get/set value path, restore can_sleep = false.
Marking the controller sleeping also broke atomic value consumers such
as w1-gpio (1-Wire bitbang): w1_io.c runs its read time slot under
local_irq_save() and uses the non-cansleep gpiod_set_value() /
gpiod_get_value(), which with can_sleep=true trigger WARN_ON(can_sleep)
in gpiolib on every transferred bit (from w1_gpio_write_bit() /
w1_gpio_read_bit() via w1_reset_bus() and w1_search()). The printk and
stack dump inside the IRQs-off, microsecond-scale time slot destroy the
bit timing, so reset/presence detection and ROM search fail: the bus
master registers but w1_master_slave_count stays at 0 and no devices
are found. Verified on an Amlogic A113X board (DS18B20 on GPIOA_14):
with can_sleep restored to false the warnings are gone and the sensor
is detected and read again.
This must not be applied or backported without the shared-proxy locking
fix above; otherwise the original Khadas VIM3 splat returns on boards
that genuinely share a meson GPIO.
Fixes: 28f240683871 ("pinctrl: meson: mark the GPIO controller as sleeping")
Link: https://lore.kernel.org/all/20260105150509.56537-1-bartosz.golaszewski@oss.qualcomm.com/
Signed-off-by: Viacheslav Bocharov <v@baodeep.com>
Acked-by: Linus Walleij <linusw@kernel.org>
Link: https://patch.msgid.link/20260625115718.1678991-3-v@baodeep.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"Core changes:
- Add new generic callbacks to populate per-pin pin controllers
creating groups and functions from the device tree building out
pinctrl_generic_to_map() and move the Spacemit driver over to use
this
- Generic board-level pin control driver using the mux framework
New pin controller drivers:
- Amlogic (meson) A9 SoC
- Aspeed AST2700 SoC0 and SoC1
- nVidia Tegra264 and Tegra238
- Qualcomm Nord TLMM, Shikra TLMM, SM6350 LPASS LPI, and IPQ9650 TLMM
- Renesas RZ/G3L SoC
- UltraRISC DP1000
Improvements:
- Handle pull up/pull down properly in the Renesas RZG2L driver
- Fix up nVidia Tegra 234 DT bindings
- Fix up pin definitions in the Qualcomm Eliza driver
- Qualcomm PM8010 GPIO support in the PM8010
- Qualcomm SM6115 EGPIO support in the SM6115
- Switch Qualcomm LPASS LPI drivers to use runtime PM for power
management
- Clean up the Qualcomm Kconfig business a bit to include the
necessary drivers for each subarch
- Fix output glitch in the Amlogic (meson) A4 pin controller
- Move the Airoha driver from the Mediatek directory to its own
directory. It is too different from other Mediatek hardware
- A slew of fixes to the Airoha AN7581 and AN7583 drivers"
* tag 'pinctrl-v7.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (151 commits)
pinctrl: Export pinctrl_get_group_selector()
pinctrl: Match DT helper types
pinctrl: qcom: Register functions before enabling pinctrl
pinctrl: meson: amlogic-a4: use nolock get range
pinctrl: ultrarisc: Add UltraRISC DP1000 pinctrl driver
dt-bindings: pinctrl: Add UltraRISC DP1000 pinctrl controller
pinctrl: qcom: Remove unused macro definitions
pinctrl: tegra: PINCTRL_TEGRA264 should depend on ARCH_TEGRA
pinctrl: tegra: PINCTRL_TEGRA238 should depend on ARCH_TEGRA
pinctrl: tegra238: add missing AON pin groups
dt-bindings: pinctrl: tegra238: add missing AON pin groups
pinctrl: airoha: an7583: remove undefined groups from pcm_spi pin function
pinctrl: airoha: an7583: fix phy1_led1 pin function
pinctrl: airoha: an7583: add missed gpio22 pin group
pinctrl: airoha: an7583: fix gpio21 pin group
pinctrl: airoha: fix pwm pin function for an7581 and an7583
pinctrl: airoha: an7583: fix incorrect led mapping in phy4_led1 pin function
pinctrl: airoha: an7581: fix incorrect led mapping in phy4_led1 pin function
pinctrl: airoha: an7583: fix misprint in gpio19 pinconf
pinctrl: airoha: an7581: fix misprint in gpio19 pinconf
...
|
|
Use pinctrl_find_gpio_range_from_pin_nolock() instead of
pinctrl_find_gpio_range_from_pin() when configuring a pin or
setting a GPIO value.
This avoids taking the lock and allows the code to be safely
called from interrupt context.
Signed-off-by: Xianwei Zhao <xianwei.zhao@amlogic.com>
Signed-off-by: Linus Walleij <linusw@kernel.org>
|
|
In Amlogic A9 SoC, subordinate bank reuse other master bank is
not from bit0, and subordinate bank reuse multi master banks.
This submission implements this situation.
Signed-off-by: Xianwei Zhao <xianwei.zhao@amlogic.com>
Signed-off-by: Linus Walleij <linusw@kernel.org>
|
|
When the system transitions from bootloader to kernel, the GPIO is
expected to keep driving high.
However, the Linux kernel first configures the pin direction and then
sets the output value. This may cause a brief low-level glitch on the
GPIO line, which can be problematic for regulator control.
By configuring the output value before switching the pin direction to
output, the glitch can be avoided.
This commit fixes the issue by swapping the configuration order.
Fixes: 6e9be3abb78c ("pinctrl: Add driver support for Amlogic SoCs")
Signed-off-by: Xianwei Zhao <xianwei.zhao@amlogic.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Linus Walleij <linusw@kernel.org>
|
|
Accessing the pinconf-pins sysfs node may deadlock.
pinconf_pins_show() holds pctldev->mutex, and the platform driver
calls pinctrl_find_gpio_range_from_pin(), which tries to acquire
the same mutex again, leading to a deadlock.
Use pinctrl_find_gpio_range_from_pin_nolock() to fix this issue.
Fixes: 6e9be3abb78c ("pinctrl: Add driver support for Amlogic SoCs")
Signed-off-by: Xianwei Zhao <xianwei.zhao@amlogic.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Linus Walleij <linusw@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"Core changes:
- Perform basic checks on pin config properties so as not to allow
directly contradictory settings such as setting a pin to more than
one bias or drive mode
- Handle input-threshold-voltage-microvolt property
- Introduce pinctrl_gpio_get_config() handling in the core for SCMI
GPIO using pin control
New drivers:
- GPIO-by-pin control driver (also appearing in the GPIO pull
request) fulfilling a promise on a comment from Grant Likely many
years ago: "can't GPIO just be a front-end for pin control?" it
turns out it can, if and only if you design something new from
scratch, such as SCMI
- Broadcom BCM7038 as a pinctrl-single delegate
- Mobileye EyeQ6Lplus OLB pin controller
- Qualcomm Eliza and Hawi families TLMM pin controllers
- Qualcomm SDM670 and Milos family LPASS LPI pin controllers
- Qualcomm IPQ5210 pin controller
- Realtek RTD1625 pin controller support
- Rockchip RV1103B pin controller support
- Texas Instruments AM62L as a pinctrl-single delegate
Improvements:
- Set config implementation for the Spacemit K1 pin controller"
* tag 'pinctrl-v7.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (84 commits)
pinctrl: qcom: Add Hawi pinctrl driver
dt-bindings: pinctrl: qcom: Describe Hawi TLMM block
dt-bindings: pinctrl: pinctrl-max77620: convert to DT schema
pinctrl: single: Add bcm7038-padconf compatible matching
dt-bindings: pinctrl: pinctrl-single: Add brcm,bcm7038-padconf
dt-bindings: pinctrl: apple,pinctrl: Add t8122 compatible
pinctrl: qcom: sdm670-lpass-lpi: label variables as static
pinctrl: sophgo: pinctrl-sg2044: Fix wrong module description
pinctrl: sophgo: pinctrl-sg2042: Fix wrong module description
pinctrl: qcom: add sdm670 lpi tlmm
dt-bindings: pinctrl: qcom: Add SDM670 LPASS LPI pinctrl
dt-bindings: qcom: lpass-lpi-common: add reserved GPIOs property
pinctrl: qcom: Introduce IPQ5210 TLMM driver
dt-bindings: pinctrl: qcom: add IPQ5210 pinctrl
pinctrl: qcom: Drop redundant intr_target_reg on modern SoCs
pinctrl: qcom: eliza: Fix interrupt target bit
pinctrl: core: Don't use "proxy" headers
pinctrl: amd: Support new ACPI ID AMDI0033
pinctrl: renesas: rzg2l: Drop superfluous blank line
pinctrl: renesas: rzg2l: Fix save/restore of {IOLH,IEN,PUPD,SMT} registers
...
|
|
OF_GPIO is selected automatically on all OF systems. Any symbols it
controls also provide stubs so there's really no reason to select it
explicitly.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Signed-off-by: Linus Walleij <linusw@kernel.org>
|
|
aml_dt_node_to_map_pinmux()
The of_get_parent() function returns a device_node with an incremented
reference count.
Use the __free(device_node) cleanup attribute to ensure of_node_put()
is automatically called when pnode goes out of scope, fixing a
reference leak.
Fixes: 6e9be3abb78c ("pinctrl: Add driver support for Amlogic SoCs")
Signed-off-by: Felix Gu <ustc.gu@gmail.com>
Signed-off-by: Linus Walleij <linusw@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"Core changes:
- Drop the unused devm_pinctrl_unregister() function
- Move pretended generic pin control functionality out of the core
and into the Amlogic AM4 driver. We have something better coming
(hopefully)
New hardware support:
- Spacemit K3 (RISC-V) pin control support
- Atmel AT91 PIO4 (ARM32) SAMA7D65 pin control support
- Exynos9610 (ARM64) pin control support
- Qualcomm Mahua TLMM (ARM64) pin control support
- Microchip Polarfire MSSIO (RISC-V) pin control support
- Ocelot LAN9645XF (multiplatform) pin control support
Improvements:
- Using a few more guards for locking
- Various nonurgent fixes and tweaks"
* tag 'pinctrl-v7.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (73 commits)
pinctrl: generic: move function to amlogic-am4 driver
pinctrl: intel: Align Copyright note with corporate guidelines
pinctrl: mediatek: remove unused drv_offset field
pinctrl: canaan: k230: Fix NULL pointer dereference when parsing devicetree
pinctrl: single: fix refcount leak in pcs_add_gpio_func()
pinctrl: meson: amlogic-a4: Fix device node reference leak in bank helpers
pinctrl: qcom: sm8250-lpass-lpi: Fix i2s2_data_groups definition
pinctrl: core: Remove duplicate error messages
pinctrl: core: Simplify devm_pinctrl_*()
pinctrl: core: Remove unused devm_pinctrl_unregister()
dt-bindings: pinctrl: spacemit: fix drive-strength check warning
pinctrl: fix kismet issues with GENERIC_PINCTRL
pinctrl: tangier: Join tng_pinctrl_probe() into its wrapper
pinctrl: tangier: Remove duplicate error messages
pinctrl: lynxpoint: Remove duplicate error messages
pinctrl: cherryview: Remove duplicate error messages
pinctrl: baytrail: Remove duplicate error messages
pinctrl: intel: Remove duplicate error messages
pinctrl: equilibrium: Fix device node reference leak in pinbank_init()
dt-bindings: pinctrl: pinctrl-microchip-sgpio: add LAN969x
...
|
|
pinconf_generic_dt_node_to_map_pinmux() is not actually a generic
function, and really belongs in the amlogic-am4 driver. There are three
reasons why.
First, and least, of the reasons is that this function behaves
differently to the other dt_node_to_map functions in a way that is not
obvious from a first glance. This difference stems for the devicetree
properties that the function is intended for use with, and how they are
typically used. The other generic dt_node_to_map functions support
platforms where the pins, groups and functions are described statically
in the driver and require a function that will produce a mapping from dt
nodes to these pre-established descriptions. No other code in the driver
is require to be executed at runtime.
pinconf_generic_dt_node_to_map_pinmux() on the other hand is intended for
use with the pinmux property, where groups and functions are determined
entirely from the devicetree. As a result, there are no statically
defined groups and functions in the driver for this function to perform
a mapping to. Other drivers that use the pinmux property (e.g. the k1)
their dt_node_to_map function creates the groups and functions as the
devicetree is parsed. Instead of that,
pinconf_generic_dt_node_to_map_pinmux() requires that the devicetree is
parsed twice, once by it and once at probe, so that the driver
dynamically creates the groups and functions before the dt_node_to_map
callback is executed. I don't believe this double parsing requirement is
how developers would expect this to work and is not necessary given
there are drivers that do not have this behaviour.
Secondly and thirdly, the function bakes in some assumptions that only
really match the amlogic platform about how the devicetree is constructed.
These, to me, are problematic for something that claims to be generic.
The other dt_node_to_map implementations accept a being called for
either a node containing pin configuration properties or a node
containing child nodes that each contain the configuration properties.
IOW, they support the following two devicetree configurations:
| cfg {
| label: group {
| pinmux = <asjhdasjhlajskd>;
| config-item1;
| };
| };
| label: cfg {
| group1 {
| pinmux = <dsjhlfka>;
| config-item2;
| };
| group2 {
| pinmux = <lsdjhaf>;
| config-item1;
| };
| };
pinconf_generic_dt_node_to_map_pinmux() only supports the latter.
The other assumption about devicetree configuration that the function
makes is that the labeled node's parent is a "function node". The amlogic
driver uses these "function nodes" to create the functions at probe
time, and pinconf_generic_dt_node_to_map_pinmux() finds the parent of
the node it is operating on's name as part of the mapping. IOW, it
requires that the devicetree look like:
| pinctrl@bla {
|
| func-foo {
| label: group-default {
| pinmuxes = <lskdf>;
| };
| };
| };
and couldn't be used if the nodes containing the pinmux and
configuration properties are children of the pinctrl node itself:
| pinctrl@bla {
|
| label: group-default {
| pinmuxes = <lskdf>;
| };
| };
These final two reasons are mainly why I believe this is not suitable as
a generic function, and should be moved into the driver that is the sole
user and originator of the "generic" function.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Linus Walleij <linusw@kernel.org>
|
|
of_parse_phandle_with_fixed_args() increments the reference count of the
returned device node, so it must be explicitly released using
of_node_put() after use.
Fix the reference leak in aml_bank_pins() and aml_bank_number() by
adding the missing of_node_put() calls.
Fixes: 6e9be3abb78c ("pinctrl: Add driver support for Amlogic SoCs")
Signed-off-by: Felix Gu <ustc.gu@gmail.com>
Reviewed-by: Xianwei Zhao <xianwei.zhao@amlogic.com>
Signed-off-by: Linus Walleij <linusw@kernel.org>
|
|
The GPIO controller is configured as non-sleeping but it uses generic
pinctrl helpers which use a mutex for synchronization.
This can cause the following lockdep splat with shared GPIOs enabled on
boards which have multiple devices using the same GPIO:
BUG: sleeping function called from invalid context at
kernel/locking/mutex.c:591
in_atomic(): 1, irqs_disabled(): 1, non_block: 0, pid: 142, name:
kworker/u25:3
preempt_count: 1, expected: 0
RCU nest depth: 0, expected: 0
INFO: lockdep is turned off.
irq event stamp: 46379
hardirqs last enabled at (46379): [<ffff8000813acb24>]
_raw_spin_unlock_irqrestore+0x74/0x78
hardirqs last disabled at (46378): [<ffff8000813abf38>]
_raw_spin_lock_irqsave+0x84/0x88
softirqs last enabled at (46330): [<ffff8000800c71b4>]
handle_softirqs+0x4c4/0x4dc
softirqs last disabled at (46295): [<ffff800080010674>]
__do_softirq+0x14/0x20
CPU: 1 UID: 0 PID: 142 Comm: kworker/u25:3 Tainted: G C
6.19.0-rc4-next-20260105+ #11963 PREEMPT
Tainted: [C]=CRAP
Hardware name: Khadas VIM3 (DT)
Workqueue: events_unbound deferred_probe_work_func
Call trace:
show_stack+0x18/0x24 (C)
dump_stack_lvl+0x90/0xd0
dump_stack+0x18/0x24
__might_resched+0x144/0x248
__might_sleep+0x48/0x98
__mutex_lock+0x5c/0x894
mutex_lock_nested+0x24/0x30
pinctrl_get_device_gpio_range+0x44/0x128
pinctrl_gpio_set_config+0x40/0xdc
gpiochip_generic_config+0x28/0x3c
gpio_do_set_config+0xa8/0x194
gpiod_set_config+0x34/0xfc
gpio_shared_proxy_set_config+0x6c/0xfc [gpio_shared_proxy]
gpio_do_set_config+0xa8/0x194
gpiod_set_transitory+0x4c/0xf0
gpiod_configure_flags+0xa4/0x480
gpiod_find_and_request+0x1a0/0x574
gpiod_get_index+0x58/0x84
devm_gpiod_get_index+0x20/0xb4
devm_gpiod_get+0x18/0x24
mmc_pwrseq_emmc_probe+0x40/0xb8
platform_probe+0x5c/0xac
really_probe+0xbc/0x298
__driver_probe_device+0x78/0x12c
driver_probe_device+0xdc/0x164
__device_attach_driver+0xb8/0x138
bus_for_each_drv+0x80/0xdc
__device_attach+0xa8/0x1b0
Fixes: 6ac730951104 ("pinctrl: add driver for Amlogic Meson SoCs")
Cc: stable@vger.kernel.org
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Closes: https://lore.kernel.org/all/00107523-7737-4b92-a785-14ce4e93b8cb@samsung.com/
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Linus Walleij <linusw@kernel.org>
|
|
The GPIO controller is configured as non-sleeping but it uses generic
pinctrl helpers which use a mutex for synchronization. This will cause
lockdep splats when used together with shared GPIOs going through the
GPIO shared proxy driver.
Fixes: 6e9be3abb78c ("pinctrl: Add driver support for Amlogic SoCs")
Cc: stable@vger.kernel.org
Reported-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Closes: https://lore.kernel.org/all/CAFBinCAc7CO8gfNQakCu3LfkYXuyTd2iRpMRm8EKXSL0mwOnJw@mail.gmail.com/
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Linus Walleij <linusw@kernel.org>
|
|
We currently only build these drivers on ARM but there's nothing that
should stop us from building it with allmodconfig on other
architectures. Extend the build coverage for all meson drivers.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Linus Walleij <linusw@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"We have GPIO awareness in the pin control core and an interesting
AAEON driver.
Core changes:
- Allow pins to be identified/marked as GPIO mode with a special
callback.
The pin controller core is now "aware" if a pin is in GPIO mode if
the callback is implemented in the driver, and can thus be marked
as "strict", i.e. disallowing simultaneous use of a line as GPIO
and another function such as I2C.
This is enabled in the Qualcomm TLMM driver and also implemeted
from day 1 in the new Broadcom STB driver
- Rename the pin config option PIN_CONFIG_OUTPUT to PIN_CONFIG_LEVEL
to better describe what the config is doing, as well as making it
more intuitive what shall be returned when reading this property
New drivers:
- Qualcomm SDM660 LPASS LPI TLMM pin controller subdriver
- Qualcomm Glymur family pin controller driver
- Broadcom STB family pin controller driver
- Tegra186 pin controller driver
- AAEON UP pin controller support.
This is some special pin controller that works as an external
advanced line MUX and amplifier for signals from an Intel SoC. A
cooperative effort with the GPIO maintainer was needed to reach a
solution where we reuse code from the GPIO aggregator/forwarder
driver
- Renesas RZ/T2H and RZ/N2H pin controller support
- Axis ARTPEC-8 subdriver for the Samsung pin controller driver
Improvements:
- Output enable (OEN) support in the Renesas RZG2L driver
- Properly support bias pull up/down in the pinctrl-single driver
- Move over all GPIO portions using generic MMIO GPIO to the new
generic GPIO chip management which has a nice and separate API
- Proper DT bindings for some older Broadcom SoCs
- External GPIO (EGPIO) support in the Qualcomm SM8250
Deleted code:
- Dropped the now unused Samsung S3C24xx drivers"
* tag 'pinctrl-v6.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (75 commits)
pinctrl: use more common syntax for compound literals
pinctrl: Simplify printks with pOF format
pinctrl: qcom: Add SDM660 LPASS LPI TLMM
dt-bindings: pinctrl: qcom: Add SDM660 LPI pinctrl
pinctrl: qcom: lpass-lpi: Add ability to use custom pin offsets
pinctrl: qcom: Add glymur pinctrl driver
dt-bindings: pinctrl: qcom: Add Glymur pinctrl
pinctrl: qcom: sm8250: Add egpio support
pinctrl: generic: rename PIN_CONFIG_OUTPUT to LEVEL
pinctrl: keembay: fix double free in keembay_build_functions()
pinctrl: spacemit: fix typo in PRI_TDI pin name
pinctrl: eswin: Fix regulator error check and Kconfig dependency
pinctrl: bcm: Add STB family pin controller driver
dt-bindings: pinctrl: Add support for Broadcom STB pin controller
pinctrl: qcom: make the pinmuxing strict
pinctrl: qcom: mark the `gpio` and `egpio` pins function as non-strict functions
pinctrl: qcom: add infrastructure for marking pin functions as GPIOs
pinctrl: allow to mark pin functions as requestable GPIOs
pinctrl: qcom: use generic pin function helpers
pinctrl: make struct pinfunction a pointer in struct function_desc
...
|
|
This generic pin config property is confusingly named so let's
rename it to make things clearer.
There are already drivers in the tree that use PIN_CONFIG_OUTPUT
to *read* the value of an output driven pin, which is a big
semantic confusion for the head: are we then reading the
setting of the output or the actual value/level that is put
out on the pin?
We already have PIN_CONFIG_OUTPUT_ENABLE that turns on driver
buffers for output, so this can by logical conclusion only
drive the voltage level if it should be any different.
But if we read the pin, are we then reading the *setting* of
the output value or the *actual* value we can see on the
line?
If the pin has not first been set into output mode with
PIN_CONFIG_OUTPUT_ENABLE, but is instead in some input mode
or tristate, what will reading this property actually
return?
Reading the current users reading this property it is clear
that what we read is the logical level of the pin as 0 or 1
depending on if it is low or high.
Rename it to PIN_CONFIG_LEVEL so it is crystal clear that
we set or read the voltage level of the pin and nothing else.
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Amlogic GXL has 4 I2C attached to gpio-periphs. I2C_D is on GPIOX_10/11.
Add the relevant func 3 pinmux per the datasheet for S805X/S905X/S905D.
Fixes: 0f15f500ff2c ("pinctrl: meson: Add GXL pinctrl definitions")
Signed-off-by: Da Xue <da@libre.computer>
Link: https://lore.kernel.org/20250821233335.1707559-1-da@libre.computer
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Amlogic G12 exposes PCIe clock request signal on GPIOC_7 pinmux func 1
Add the relevant pinmux and pin groups
Signed-off-by: Da Xue <da@libre.computer>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/20250814181236.1956731-1-da@libre.computer
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The typo when using the MODULE_DEVICE_TABLE macro was not noticeable
because the macro was defined only if the module was built as a separate
module.
Cc: Xianwei Zhao <xianwei.zhao@amlogic.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Neil Armstrong <neil.armstrong@linaro.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: linux-amlogic@lists.infradead.org
Cc: linux-gpio@vger.kernel.org
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202507220009.8HKbNP16-lkp@intel.com/
Signed-off-by: Alexey Gladkov <legion@kernel.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/e548b7761302defec15aa2098172eabb1ce1ad4a.1755170493.git.legion@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The conversion of all GPIO drivers to using the .set_rv() and
.set_multiple_rv() callbacks from struct gpio_chip (which - unlike their
predecessors - return an integer and allow the controller drivers to
indicate failures to users) is now complete and the legacy ones have
been removed. Rename the new callbacks back to their original names in
one sweeping change.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Sparse complains:
sparse warnings: (new ones prefixed by >>)
>> drivers/pinctrl/meson/pinctrl-amlogic-a4.c:126:24: sparse: sparse:
symbol 'multi_mux_s7' was not declared. Should it be static?
>> drivers/pinctrl/meson/pinctrl-amlogic-a4.c:135:28: sparse: sparse:
symbol 's7_priv_data' was not declared. Should it be static?
>> drivers/pinctrl/meson/pinctrl-amlogic-a4.c:140:24: sparse: sparse:
symbol 'multi_mux_s6' was not declared. Should it be static?
>> drivers/pinctrl/meson/pinctrl-amlogic-a4.c:154:28: sparse: sparse:
symbol 's6_priv_data' was not declared. Should it be static?
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202506122145.wWAtKBoy-lkp@intel.com/
Cc: Xianwei Zhao <xianwei.zhao@amlogic.com>
Fixes: 1f8e5dfddaa7 ("pinctrl: meson: support amlogic S6/S7/S7D SoC")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/20250624-amlogic-a4-fix-v1-1-03f0856d10cb@linaro.org
|
|
G12B and SM1 have additional PWM pinmuxes for b, c, and d.
Signed-off-by: Da Xue <da@libre.computer>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/20250619022337.43900-1-da@libre.computer
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
In some Amlogic SoCs, to save register space or due to some
abnormal arrangements, two sets of pins share one mux register.
A group starting from pin0 is the main pin group, which acquires
the register address through DTS and has management permissions,
but the register bit offset is undetermined.
Another GPIO group as a subordinate group. Some pins mux use share
register and bit offset from bit0 . But this group do not have
register management permissions.
This submission implements this situation.
Signed-off-by: Xianwei Zhao <xianwei.zhao@amlogic.com>
Link: https://lore.kernel.org/20250527-s6-s7-pinctrl-v3-3-44f6a0451519@amlogic.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
According to the data specifications of Amlogic's existing SoCs,
the function register offset and the bit offset are the same
value among various chips. Therefore, general processing can
be carried out without the need for private data modification.
Drop special data processing.
Signed-off-by: Xianwei Zhao <xianwei.zhao@amlogic.com>
Link: https://lore.kernel.org/20250527-s6-s7-pinctrl-v3-2-44f6a0451519@amlogic.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"An especially linear and sparse improvement and new drivers release.
Nothing exciting. The biggest change in Bartosz changes to make
gpiochip set/get calls return error codes (something we should have
fixed ages ago but is now finally getting fixed.)
Core changes:
- Add the devres devm_pinctrl_register_mappings() call that can
register some pin control machine mappings and have them go away
with the associated device
New drivers:
- Support for the Mediatek MT6893 and MT8196 SoCs
- Support for the Renesas RZ/V2N SoC
- Support for the NXP Freescale i.MX943 SoC
Improvements:
- Per-SoC suspend/resume callbacks in the Samsung drivers
- Set all pins as input (High-Z) at probe in the MCP23S08 driver
- Switch most GPIO chips to use the setters/getters with a return
value
- EGPIO support in the Qualcomm QCM2290 driver
- Fix up the number of available GPIO lines in Qualcomm QCS8300 and
QCS615"
* tag 'pinctrl-v6.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (82 commits)
pinctrl: freescale: Add support for imx943 pinctrl
pinctrl: core: add devm_pinctrl_register_mappings()
pinctrl: remove extern specifier for functions in machine.h
pinctrl: mediatek: eint: Fix invalid pointer dereference for v1 platforms
pinctrl: freescale: Enable driver if platform is enabled.
pinctrl: freescale: Depend imx-scu driver on OF
pinctrl: armada-37xx: propagate error from armada_37xx_pmx_set_by_name()
pinctrl: armada-37xx: propagate error from armada_37xx_gpio_get_direction()
pinctrl: armada-37xx: propagate error from armada_37xx_pmx_gpio_set_direction()
pinctrl: armada-37xx: propagate error from armada_37xx_gpio_get()
pinctrl: armada-37xx: propagate error from armada_37xx_gpio_direction_output()
pinctrl: armada-37xx: set GPIO output value before setting direction
pinctrl: armada-37xx: use correct OUTPUT_VAL register for GPIOs > 31
pinctrl: meson: Drop unused aml_pctl_find_group_by_name()
pinctrl: at91: Fix possible out-of-boundary access
pinctrl: add stubs for OF-specific pinconf functions
pinctrl: qcom: correct the ngpios entry for QCS8300
pinctrl: qcom: correct the ngpios entry for QCS615
dt-bindings: pinctrl: qcom: correct gpio-ranges in examples for qcs8300
dt-bindings: pinctrl: qcom: correct gpio-ranges in examples for qcs615
...
|
|
aml_pctl_find_group_by_name() is not used anywhere, as reported by W=1
clang build:
pinctrl-amlogic-a4.c:600:2: error: unused function 'aml_pctl_find_group_by_name' [-Werror,-Wunused-function]
Fixes: 6e9be3abb78c ("pinctrl: Add driver support for Amlogic SoCs")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Xianwei Zhao <xianwei.zhao@amlogic.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/20250509150114.299962-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
struct gpio_chip now has callbacks for setting line values that return
an integer, allowing to indicate failures. Convert the driver to using
them.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Xianwei Zhao <xianwei.zhao@amlogic.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/20250408-gpiochip-set-rv-pinctrl-part1-v1-6-c9d521d7c8c7@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
struct gpio_chip now has callbacks for setting line values that return
an integer, allowing to indicate failures. Convert the driver to using
them.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/20250408-gpiochip-set-rv-pinctrl-part1-v1-5-c9d521d7c8c7@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Enabling the compile test should not cause automatic enabling of all
drivers. Restrict the default to ARCH also for individual drivers, even
though their choice is not visible without selecting parent Kconfig
symbol, because otherwise selecting parent would select the child during
compile testing.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/20250404115719.309999-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The public datasheets of the following Amlogic SoCs describe a typical
resistor value for the built-in pull up/down resistor:
- Meson8/8b/8m2: not documented
- GXBB (S905): 60 kOhm
- GXL (S905X): 60 kOhm
- GXM (S912): 60 kOhm
- G12B (S922X): 60 kOhm
- SM1 (S905D3): 60 kOhm
The public G12B and SM1 datasheets additionally state min and max
values:
- min value: 50 kOhm for both, pull-up and pull-down
- max value for the pull-up: 70 kOhm
- max value for the pull-down: 130 kOhm
Use 60 kOhm in the pinctrl-meson driver as well so it's shown in the
debugfs output. It may not be accurate for Meson8/8b/8m2 but in reality
60 kOhm is closer to the actual value than 1 Ohm.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/20250329190132.855196-1-martin.blumenstingl@googlemail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The kernel bots complain about untidy code found using
coccinelle, fix it up.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202503212354.Hx2qaDRe-lkp@intel.com/
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The register of pin input attribute means the opposite.
value of reigster meaning is 1 for input and 0 for output.
So fix it.
Fixes: 6e9be3abb78c ("pinctrl: Add driver support for Amlogic SoCs")
Signed-off-by: Xianwei Zhao <xianwei.zhao@amlogic.com>
Link: https://lore.kernel.org/20250303-fix-a4-pinctl-v1-1-6579888b4272@amlogic.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add a new pinctrl driver for Amlogic SoCs. All future Amlogic
SoCs pinctrl drives use this, such A4, A5, S6, S7 etc. To support
new Amlogic SoCs, only need to add the corresponding dts file.
Signed-off-by: Xianwei Zhao <xianwei.zhao@amlogic.com>
Link: https://lore.kernel.org/20250212-amlogic-pinctrl-v5-3-282bc2516804@amlogic.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The following structures are not modified in these drivers.
- struct meson_bank
- struct meson_pmx_bank
- struct meson_pmx_func
- struct meson_pmx_group
- struct meson_pinctrl_data
- struct meson_axg_pmx_data
Constifying these structures moves some data to a read-only section, so
increase overall security.
On a x86_64, with allmodconfig:
Before:
======
text data bss dec hex filename
10818 11696 0 22514 57f2 drivers/pinctrl/meson/pinctrl-amlogic-c3.o
17198 17680 0 34878 883e drivers/pinctrl/meson/pinctrl-amlogic-t7.o
14161 11200 0 25361 6311 drivers/pinctrl/meson/pinctrl-meson8b.o
17348 12512 0 29860 74a4 drivers/pinctrl/meson/pinctrl-meson8.o
3070 324 0 3394 d42 drivers/pinctrl/meson/pinctrl-meson8-pmx.o
9317 9648 0 18965 4a15 drivers/pinctrl/meson/pinctrl-meson-a1.o
12115 11664 0 23779 5ce3 drivers/pinctrl/meson/pinctrl-meson-axg.o
2470 120 0 2590 a1e drivers/pinctrl/meson/pinctrl-meson-axg-pmx.o
15125 15224 0 30349 768d drivers/pinctrl/meson/pinctrl-meson-g12a.o
13800 10160 0 23960 5d98 drivers/pinctrl/meson/pinctrl-meson-gxbb.o
13040 9648 0 22688 58a0 drivers/pinctrl/meson/pinctrl-meson-gxl.o
20507 1132 48 21687 54b7 drivers/pinctrl/meson/pinctrl-meson.o
12212 12880 0 25092 6204 drivers/pinctrl/meson/pinctrl-meson-s4.o
After:
=====
text data bss dec hex filename
22242 248 0 22490 57da drivers/pinctrl/meson/pinctrl-amlogic-c3.o
34638 248 0 34886 8846 drivers/pinctrl/meson/pinctrl-amlogic-t7.o
25137 232 0 25369 6319 drivers/pinctrl/meson/pinctrl-meson8b.o
29604 232 0 29836 748c drivers/pinctrl/meson/pinctrl-meson8.o
3070 324 0 3394 d42 drivers/pinctrl/meson/pinctrl-meson8-pmx.o
18725 248 0 18973 4a1d drivers/pinctrl/meson/pinctrl-meson-a1.o
23539 248 0 23787 5ceb drivers/pinctrl/meson/pinctrl-meson-axg.o
2470 120 0 2590 a1e drivers/pinctrl/meson/pinctrl-meson-axg-pmx.o
30101 256 0 30357 7695 drivers/pinctrl/meson/pinctrl-meson-g12a.o
23688 248 0 23936 5d80 drivers/pinctrl/meson/pinctrl-meson-gxbb.o
22416 248 0 22664 5888 drivers/pinctrl/meson/pinctrl-meson-gxl.o
20507 1132 48 21687 54b7 drivers/pinctrl/meson/pinctrl-meson.o
24820 248 0 25068 61ec drivers/pinctrl/meson/pinctrl-meson-s4.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/f74e326bd7d48003c06219545bad7c2ef1a84bf8.1723053850.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
When ARCH=x86, make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/pinctrl/bcm/pinctrl-bcm4908.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/pinctrl/pinctrl-mcp23s08_i2c.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/pinctrl/pinctrl-mcp23s08_spi.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/pinctrl/pinctrl-mcp23s08.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/pinctrl/meson/pinctrl-meson.o
Add the missing invocation of the MODULE_DESCRIPTION() macro to all
files which have a MODULE_LICENSE().
This includes many meson drivers which, although they did not produce
a warning with the x86 allmodconfig configuration, may cause this
warning with ARM or ARM64 configurations.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org> # for Amlogic Pinctrl drivers
Link: https://lore.kernel.org/r/20240610-md-drivers-pinctrl-v1-1-68462e3d960c@quicinc.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Other pins have _a or _x suffix, but this one doesn't have any. Most
likely this is a typo.
Fixes: dabad1ff8561 ("pinctrl: meson: add pinctrl driver support for Meson-A1 SoC")
Signed-off-by: Jan Dakinevich <jan.dakinevich@salutedevices.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Message-ID: <20240325113058.248022-1-jan.dakinevich@salutedevices.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add a new pinctrl driver for Amlogic T7 SoCs which share
the same register layout as the previous Amlogic S4.
Signed-off-by: Huqiang Qin <huqiang.qin@amlogic.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://lore.kernel.org/r/20230922094342.637251-3-huqiang.qin@amlogic.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Documentation/process/license-rules.rst and checkpatch expect the SPDX
identifier syntax for multiple licenses to use capital "OR". Correct it
to keep consistent format and avoid copy-paste issues.
Correct also the placement of SPDX identifier in pinctrl-meson-axg
files:
WARNING: Misplaced SPDX-License-Identifier tag - use line 1 instead
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230823085546.116494-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Replacing IRQ numbers with IRQID macro definitions makes driver code
easier to understand.
Associated platforms:
- Amlogic Meson-G12A
- Amlogic Meson-G12B
- Amlogic Meson-SM1
Signed-off-by: Huqiang Qin <huqiang.qin@amlogic.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20230724060108.1403662-3-huqiang.qin@amlogic.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add a new pinctrl driver for Amlogic C3 SoCs which share
the same register layout as the previous Amlogic S4.
Signed-off-by: Huqiang Qin <huqiang.qin@amlogic.com>
Link: https://lore.kernel.org/r/20230714122441.3098337-3-huqiang.qin@amlogic.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Acked-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230714174901.4062397-1-robh@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Without this, the gpio cannot be explicitly mux'ed to its gpio function.
Fixes: 83c566806a68a ("pinctrl: meson-axg: Add new pinctrl driver for Meson AXG SoC")
Cc: stable@vger.kernel.org
Signed-off-by: Martin Hundebøll <martin@geanix.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Dmitry Rokosov <ddrokosov@sberdevices.ru>
Link: https://lore.kernel.org/r/20230512064925.133516-1-martin@geanix.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
GPIO library now accepts fwnode as a firmware node, so
switch the driver to use it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20220905180034.73132-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/andy/linux-gpio-intel into devel
intel-gpio for v5.19-1
* Introduce helpers to iterate over GPIO chip nodes and covert some drivers
The following is an automated git shortlog grouped by driver:
gpiolib:
- Introduce a helper to get first GPIO controller node
- Introduce gpiochip_node_count() helper
- Introduce for_each_gpiochip_node() loop helper
pinctrl:
- meson: Replace custom code by gpiochip_node_count() call
- meson: Enable COMPILE_TEST
- meson: Rename REG_* to MESON_REG_*
- armada-37xx: Reuse GPIO fwnode in armada_37xx_irqchip_register()
- armada-37xx: Switch to use fwnode instead of of_node
- samsung: Switch to use for_each_gpiochip_node() helper
- samsung: Drop redundant node parameter in samsung_banks_of_node_get()
- npcm7xx: Switch to use for_each_gpiochip_node() helper
- renesas: rza1: Switch to use for_each_gpiochip_node() helper
- renesas: rza1: Replace custom code by gpiochip_node_count() call
- stm32: Switch to use for_each_gpiochip_node() helper
- stm32: Replace custom code by gpiochip_node_count() call
|
|
The kernel test robot reported a warning as below:
>> drivers/pinctrl/meson/pinctrl-meson-s4.c:178:27: warning: unused variable 'tdm_sclk1_c_pins' [-Wunused-const-variable]
static const unsigned int tdm_sclk1_c_pins[] = { GPIOC_3 };
Fix it by adding missing description about this pins
Fixes: 775214d389c2 ("pinctrl: meson: add pinctrl driver support for Meson-S4 Soc")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Qianggui Song <qianggui.song@amlogic.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20220330023720.18238-1-qianggui.song@amlogic.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Since we have generic function to count GPIO controller nodes
under a given device, there is no need to open code it. Replace
custom code by gpiochip_node_count() call.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
Enable COMPILE_TEST for a better test coverage.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
Currently compilation test fails on x86 due to name collision. The usual
way to fix that is to move both conflicting parts to their own namespaces.
Rename REG_* to MESON_REG_* as a prerequisite for enabling COMPILE_TEST.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
Add new pinctrl driver for Amlogic's Meson-S4 SoC which share the
same register layout as the previous Meson-A1.
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Qianggui Song <qianggui.song@amlogic.com>
Link: https://lore.kernel.org/r/20220113031044.2665-4-qianggui.song@amlogic.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
