| Age | Commit message (Collapse) | Author |
|---|
|
|
|
On ACE2+ platforms the link DMA stream allocator must avoid two
hardware errata in mlink-capable systems:
- Concurrent (cross-direction) hazard: when SoundWire shares a physical
link DMA stream index with HDaudio, iDisp or UAOL across the two
directions, the LLP and timestamp values for the affected stream are
wrong. SSP and DMIC are not affected because every DMA request from
those links carries one sample block.
- Sequential (playback only) hazard: once a HDaudio or iDisp link has
used a playback stream index, that index cannot drive any non
HDA/iDisp link in the same direction until the next controller
reset (CRST#).
Track the active link type per direction in two masks (one for SoundWire,
one for HDA/iDisp/UAOL) and the persistent set of playback stream
indices touched by HDA/iDisp in a third mask. The link DMA allocator
skips streams that would violate either rule. Streams are released from
the active masks when the stream is released; all masks are cleared in
hda_dsp_ctrl_init_chip() because the CRST# performed there clears the
hardware state as well.
A new helper hda_bus_ml_link_get_type() returns the link type from the
existing extended link descriptor so the SOF allocator can tell
SoundWire, HDA/iDisp and UAOL apart without duplicating the parsing.
The implementation is generic. On platforms older than ACE2 every link
is reported as HDA, only the sequential mask is ever set and it has no
effect because no other link types are present, so behavior is
unchanged.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Liam Girdwood <liam.r.girdwood@intel.com>
Link: https://patch.msgid.link/20260730125130.29887-5-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The helper became unused after probe no longer drops all non-alt
links, so remove the dead API and implementation.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Liam Girdwood <liam.r.girdwood@intel.com>
Link: https://patch.msgid.link/20260730125130.29887-4-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Drop the hda_bus_ml_put_all() call at the end of hda_init_caps().
On multi-link (mlink) capable platforms the non-alternate links
(HDaudio and iDisp) are powered on by hardware when CRST# is
de-asserted (LCTL.SPA = 1) and their ref_count is pre-charged to 1 in
hda_ml_alloc_h2link() to match this state. The put_all call
immediately dropped that reference and toggled LCTL.SPA back to 0,
relying on the first stream open to power the link up again.
On ACE2+ platforms this redundant SPA 1->0->1 toggle at probe leaves
the Processing Pipe Capability (PPLC) Linear Link Position counters in
a state where they do not advance on the first stream after boot. The
counters only start working after the first full runtime suspend/resume
cycle, which includes a CRST# assert/deassert that fully resets the PPC
AON block.
Keep the non-alt links powered from CRST# de-assert through first use.
System suspend still powers them down via hda_bus_ml_suspend(), and
resume relies on CRST# de-assert to bring them back up, so no other
path is affected.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Liam Girdwood <liam.r.girdwood@intel.com>
Link: https://patch.msgid.link/20260730125130.29887-3-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Move the hda_bus_ml_init() call from hda_init_caps() into
hda_dsp_ctrl_init_chip(), right after the HDA controller reset has
been de-asserted and unsolicited responses have been accepted.
hda_dsp_ctrl_init_chip() already calls hda_bus_ml_reset_losidv() at
the end of its sequence to clear the stream-to-link mapping. On first
boot this call was a no-op because the multi-link list had not yet
been populated: hda_bus_ml_init() only runs later in hda_init_caps().
Enumerating the links inside init_chip() makes the LOSIDV reset
effective on first boot as well, without adding a second reset call
from the probe path.
hda_bus_ml_init() now returns early when the hlink_list is already
populated, so the subsequent invocations from the D3 resume path
(hda_resume() -> hda_dsp_ctrl_init_chip(false)) are no-ops.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Liam Girdwood <liam.r.girdwood@intel.com>
Link: https://patch.msgid.link/20260730125130.29887-2-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Peter Ujfalusi <peter.ujfalusi@linux.intel.com> says:
It is expected that the DSP is in power down state when the firmware boot
is attempted.
If the DSP for any reason was left powered up then the DSP boot will
fail since the ROM boot sequence might not be able to run.
Make sure that the DSP is off before proceeding to boot it up.
We have seen reports that for some undetermined reasons the DSP was on
during system boot and this caused firmware boot failure as the DSP
cannot be booted up - it was already in booted up state.
Link: https://patch.msgid.link/20260730122857.5294-1-peter.ujfalusi@linux.intel.com
|
|
It is expected that the DSP is in power down state when the firmware boot
is attempted.
If the DSP for any reason was left powered up then the DSP boot will
fail since the ROM boot sequence might not be able to run.
Make sure that the DSP is off before proceeding to boot it up.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Liam Girdwood <liam.r.girdwood@intel.com>
Link: https://patch.msgid.link/20260730122857.5294-3-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
It is expected that the DSP is in power down state when the firmware boot
is attempted.
If the DSP for any reason was left powered up then the DSP boot will
fail since the ROM boot sequence might not be able to run.
Make sure that the DSP is off before proceeding to boot it up.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Liam Girdwood <liam.r.girdwood@intel.com>
Link: https://patch.msgid.link/20260730122857.5294-2-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
During hw_params call we make sure that the host DMA is stopped but the
hstream->running flag is not explicitly cleared at the same time.
If the host DMA fails to stop during previous use then the flag is left
set and on next start the host DMA will be left disabled since the
trigger:STOP will skip the DMA enable.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://patch.msgid.link/20260730122241.30541-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Resetting the PCMSyCM registers is required for Intel SoundWire stream. The
same procedure is done in sdw_hda_dai_hw_params() for the normal
SoundWire stream, too.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Liam Girdwood <liam.r.girdwood@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.dev>
Acked-by: Vinod Koul <vkoul@kernel.org>
Link: https://patch.msgid.link/20260730012518.2180906-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Both branches of the check return the same value, so the check has
no effect. Remove it and return the value directly.
This is the result of running the Coccinelle script from
scripts/coccinelle/misc/cond_return_no_effect.cocci.
Signed-off-by: Sang-Heon Jeon <ekffu200098@gmail.com>
Link: https://patch.msgid.link/20260723184538.3888637-15-ekffu200098@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Update header inclusions to follow IWYU (Include What You Use)
principle.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20260717172318.1784073-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The existing code disable SPIB in the playback direction only because
previously the hda data stream is only used for SOF firmware download
and we prepare capture stream for ICCMAX and prepare playback stream
for non ICCMAX case. But now the hda data stream is also used for
SoundWire BPT which will use both directions. The SPIB is enabled in
non ICCMAX cases and we should disable in clean up.
Add a is_iccmax flag in the hda_data_stream_cleanup() function to align
with the hda_data_stream_prepare() function to enable/disable the SPIB.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://patch.msgid.link/20260713084650.4138172-3-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The spib_addr register will indicate to the host DMA where the position
is in the buffer currently processed by host SW. The register is ignored
by the host DMA if SPIB is disabled. Reset it to 0 before disabling SPIB.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://patch.msgid.link/20260713084650.4138172-2-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When SND_SOC_SOF_INTEL_LNL is set, SND_SOF_SOF_HDA_SDW_BPT must also
be enabled, in order to let the soundwire support call into it.
However, there are configurations with SND_SOF_SOF_HDA_SDW_BPT=m
and SND_SOF_SOF_HDA_SDW_BPT=m but SOUNDWIRE_INTEL=y, which still
lead to a link failure:
aarch64-linux-ld: drivers/soundwire/intel_ace2x.o: in function `intel_ace2x_bpt_wait':
intel_ace2x.c:(.text+0xfc8): undefined reference to `hda_sdw_bpt_wait'
aarch64-linux-ld: drivers/soundwire/intel_ace2x.o: in function `intel_ace2x_bpt_send_async':
intel_ace2x.c:(.text+0x1ff8): undefined reference to `hda_sdw_bpt_get_buf_size_alignment'
Address this by moving the 'select SND_SOF_SOF_HDA_SDW_BPT' into
SND_SOC_SOF_HDA_GENERIC.
Fixes: 614d416dd8ae ("ASoC: SOF: Intel: hda-sdw-bpt: fix SND_SOF_SOF_HDA_SDW_BPT dependencies")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://patch.msgid.link/20260611132310.137688-2-arnd@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When SND_SOC_SOF_HDA_GENERIC=y but SND_SOC_SOF_INTEL_SOUNDWIRE=m, the
SND_SOC_SDW_UTILS is also set to =m even though there is a direct link
dependency from the hda.c:
aarch64-linux-ld: sound/soc/sof/intel/hda.o: in function `hda_machine_select':
hda.c:(.text+0x21ac): undefined reference to `codec_info_list'
hda.c:(.text+0x241c): undefined reference to `asoc_sdw_get_dai_type'
hda.c:(.text+0x25b4): undefined reference to `asoc_sdw_get_codec_info_list_count'
hda.c:(.text+0x25d8): undefined reference to `asoc_sdw_get_codec_info_list_count'
Change this the same way as the other related 'select' statements
to allow linking against it.
Fixes: 2b4d53eb5cf3 ("ASoC: SOF: Intel: select SND_SOC_SDW_UTILS in SND_SOC_SOF_HDA_GENERIC")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Julian Braha <julianbraha@gmail.com>
Link: https://patch.msgid.link/20260611132310.137688-1-arnd@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Bard Liao <yung-chuan.liao@linux.intel.com> says:
This series sets is_amp to all amp type codecs in codec_info_list[].
So that we can use the flag directly instead of using a local flag to
check if the codec is an AMP type. The flag will be used to set
different name_prefix for amp and non-amp codecs.
Link: https://patch.msgid.link/20260605101805.121428-1-yung-chuan.liao@linux.intel.com
|
|
Now we set is_amp to all amp type codecs. We can use the flag directly
instead of using a local flag to check if the codec is an AMP type.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20260605101805.121428-3-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The handling of UAOL (USB Audio Offload Link) is similar to SSP and DMIC,
it is handled by the DSP firmware.
Set the offload enable for it similar to SSP and DMIC.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://patch.msgid.link/20260520150639.25301-3-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
hdac_bus_eml_enable_offload() can only fail in case the IP is not enabled
in the platform, which is not really an error as the ACE IP can be
configured differently when integrated into a specific SoC.
While it is unlikely, but it is a valid configuration that for example the
DMIC is disabled.
In this case we will just skip setting the offload for a link that is not
present.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://patch.msgid.link/20260520150639.25301-2-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
An empty adr_link is expected to terminate the
for (adr_link = mach_params->links; adr_link->num_adr; adr_link++) loop.
Allocate link_num + 1 links to add an empty adr_link.
Fixes: 5226d19d4cae5 ("ASoC: SOF: Intel: use sof_sdw as default SDW machine driver")
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20260424105031.114053-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Bard Liao <yung-chuan.liao@linux.intel.com> says:
The platform name will be used in the topology name.
Link: https://patch.msgid.link/20260413060800.3156425-1-yung-chuan.liao@linux.intel.com
|
|
The platform name will be used in the topology name.
Fixes: d3df422f66e8a ("ASoC: SOF: Intel: add initial support for NVL-S")
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://patch.msgid.link/20260413060800.3156425-3-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The platform name will be used in the topology name.
Fixes: 1800bcdc68ead ("ASoC: SOF: Intel: add support for Nova Lake NVL")
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://patch.msgid.link/20260413060800.3156425-2-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Charles Keepax <ckeepax@opensource.cirrus.com> says:
Another round of SDCA fixes a couple of fix to the IRQ cleanup
from Richard, and a minor tweak to the IRQ handling from me.
|
|
Intel ACE4 based products set more strict constraints on HDA BDLE start
address and length alignment. Add a constraint to align period size to
128 bytes.
The commit removes the "minimum as per HDA spec" comment. This comment
was misleading as spec actually does allow a 2 byte BDLE length, and
more importantly, period size also directly impacts how the BDLE start
addresses are aligned, so it is not sufficient just to consider allowed
buffer length.
Fixes: d3df422f66e8 ("ASoC: SOF: Intel: add initial support for NVL-S")
Cc: stable@vger.kernel.org
Reported-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Liam Girdwood <liam.r.girdwood@intel.com>
Link: https://patch.msgid.link/20260408084514.24325-3-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
is_endpoint_present() iterates over sdca_data.num_functions, but checks
the dai_type according to codec info list, which will cause problems if
not all endpoints from the codec info list are present. Make sure the
type of actually present functions is compared against target dai_type.
Fixes: 5226d19d4cae ("ASoC: SOF: Intel: use sof_sdw as default SDW machine driver")
Signed-off-by: Maciej Strozek <mstrozek@opensource.cirrus.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://patch.msgid.link/20260402064531.2287261-3-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In case of missing endpoints, the sequential numbering will cause wrong
mapping. Instead, assign the original DAI index from codec_info_list.
Fixes: 5226d19d4cae ("ASoC: SOF: Intel: use sof_sdw as default SDW machine driver")
Signed-off-by: Maciej Strozek <mstrozek@opensource.cirrus.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://patch.msgid.link/20260402064531.2287261-2-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The struct hext_stream is dereferenced before it is checked for NULL.
Although it can never be NULL due to a check prior to
hda_dsp_iccmax_stream_hw_params() being called, this change clears any
confusion regarding hext_stream possibly being NULL.
Check hext_stream for NULL and then assign its members.
Detected by Smatch:
sound/soc/sof/intel/hda-stream.c:488 hda_dsp_iccmax_stream_hw_params() warn:
variable dereferenced before check 'hext_stream' (see line 486)
Fixes: aca961f196e5d ("ASoC: SOF: Intel: hda: Add helper function to program ICCMAX stream")
Signed-off-by: Ethan Tidmore <ethantidmore06@gmail.com>
Link: https://patch.msgid.link/20260324173830.17563-1-ethantidmore06@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
According to the Intel sof design, it will create the name prefix
appended with amp index for the amp codec only, such as:
rt1318-1, rt1318-2, etc...
But the rt1320 is a codec with amp and mic codec functions, it doesn't
have the amp index in its name prefix as above.
And then it will be hard to identify the codec if in multi-rt1320 case.
So we add a flag to force the amp index to be appended.
Signed-off-by: Derek Fang <derek.fang@realtek.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://patch.msgid.link/20260326075303.1083567-3-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
struct asoc_sdw_codec_info has part_id which is not
sufficient to uniquely identify devices. This change
adds the vendor_id field and updates the codec_info
list with the corresponding vendor id as per the
Manufacturer's id in https://mid.mipi.org/
Signed-off-by: Niranjan H Y <niranjan.hy@ti.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.dev>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20260324041300.784-1-niranjan.hy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This is the exact same thing as the 'alloc_obj()' version, only much
smaller because there are a lot fewer users of the *alloc_flex()
interface.
As with alloc_obj() version, this was done entirely with mindless brute
force, using the same script, except using 'flex' in the pattern rather
than 'objs*'.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This was done entirely with mindless brute force, using
git grep -l '\<k[vmz]*alloc_objs*(.*, GFP_KERNEL)' |
xargs sed -i 's/\(alloc_objs*(.*\), GFP_KERNEL)/\1)/'
to convert the new alloc_obj() users that had a simple GFP_KERNEL
argument to just drop that argument.
Note that due to the extreme simplicity of the scripting, any slightly
more complex cases spread over multiple lines would not be triggered:
they definitely exist, but this covers the vast bulk of the cases, and
the resulting diff is also then easier to check automatically.
For the same reason the 'flex' versions will be done as a separate
conversion.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This is the result of running the Coccinelle script from
scripts/coccinelle/api/kmalloc_objs.cocci. The script is designed to
avoid scalar types (which need careful case-by-case checking), and
instead replace kmalloc-family calls that allocate struct or union
object instances:
Single allocations: kmalloc(sizeof(TYPE), ...)
are replaced with: kmalloc_obj(TYPE, ...)
Array allocations: kmalloc_array(COUNT, sizeof(TYPE), ...)
are replaced with: kmalloc_objs(TYPE, COUNT, ...)
Flex array allocations: kmalloc(struct_size(PTR, FAM, COUNT), ...)
are replaced with: kmalloc_flex(*PTR, FAM, COUNT, ...)
(where TYPE may also be *VAR)
The resulting allocations no longer return "void *", instead returning
"TYPE *".
Signed-off-by: Kees Cook <kees@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for v7.0
This release is almost all abut driers, there's very little core work
here, although some of that driver work is in more generic areas like
SDCA and SOF:
- Generic SDCA support for reporting jack events.
- Continuing platform support, cleanup and feature improements for the
AMD, Intel, Qualcomm and SOF code.
- Platform description improvements for the Cirrus drivers.
- Support for NXP i.MX952, Realtek RT1320 and RT5575, and Sophogo
CV1800B.
We also pulled in one small SPI API update and some more substantial
regmap work (cache description improvements) for use in drivers.
|
|
The _hda_dsp_stream_put() function now depends on the
snd_hdac_ext_stream_release() interface from SND_HDA_EXT_CORE:
x86_64-linux-ld: vmlinux.o: in function `_hda_dsp_stream_put':
hda-stream.c:(.text+0xfac605): undefined reference to `snd_hdac_ext_stream_release'
Select this symbol the same way the other users do.
Fixes: 89e1d632bb29 ("ASoC: SOF: Intel: add hda_dsp_stream_pair_get/put helpers")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://patch.msgid.link/20260209070901.857700-1-arnd@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add a virtual CPU DAI for loopback capture for echo reference
implementation. We can't use the snd-soc-dummy-dai because it is already
used for the bluetooth DAI link.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Liam Girdwood <liam.r.girdwood@intel.com>
Reviewed-by: Mateusz Redzynia <mateuszx.redzynia@intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://patch.msgid.link/20260204081833.16630-11-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
If there's a mismatch between the DAI links in the machine driver and
the topology, it is possible that the playback/capture widget is not
set, especially in the case of loopback capture for echo reference
where we use the dummy DAI link. Return the error when the widget is not
set to avoid a null pointer dereference like below when the topology is
broken.
RIP: 0010:hda_dai_get_ops.isra.0+0x14/0xa0 [snd_sof_intel_hda_common]
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Liam Girdwood <liam.r.girdwood@intel.com>
Reviewed-by: Mateusz Redzynia <mateuszx.redzynia@intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://patch.msgid.link/20260204081833.16630-10-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Merge series from Bard Liao <yung-chuan.liao@linux.intel.com>:
Currently, hda_sdw_bpt_dma_prepare() get a HDA stream and use the link
DMA but doesn't reserve it. It works fine because we assume the
SwoundWire BPT will not run with audio streams simultaneously. Create
and use the new helpers to reserve the link DMA and allow running BPT
and audio stream simultaneously.
Pierre adds:
For the record this solution has two issues not documented in any commit
message:
a) this will not work in 'dspless' mode, where the link DMA is not
enabled. That's probably fine given that no one used that mode in
production, but that's a software restriction that you will not be able
to undo.
b) this raise the question of how bandwidth will be managed. The premise
of BPT is that it uses all the bus bandwidth to guarantee predictable
firmware download times. If the available bandwidth is restricted by
other audio streams, then mechanically the startup latency will be
increased and vary - or you will have to run the bus at a higher
frequency to provision enough bandwidth for BPT but that means higher
power consumption. Or you will have to change the bus clock dynamically
which is possible at the hardware level for SDCA parts but not legacy
ones.
I am not going to lay on the tracks for this low-level set of changes,
but you'll have to address the b) opens for future contributions.
|
|
If SDCA property is not present in the DisCo table, assume it
is present. This allows DAI links to be created from codec_info_list
instead of being skipped.
Signed-off-by: Mac Chiang <mac.chiang@intel.com>
Reviewed-by: Liam Girdwood <liam.r.girdwood@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://patch.msgid.link/20260203095923.3741674-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The existing code test if (bt_link_mask_override) to overwrite the BT
link mask. This doesn't allow user to disable the BT link mask. User may
want to disable the BT link when it is detected by the NHLT.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://patch.msgid.link/20260203111545.3742255-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Currently the SoundWire BPT stream uses the paired link DMA but not
reserve it. It works without any issue because we assume the SoundWire
BPT will not run with audio streams simultaneously.
To support simultaneous audio and BPT streams, we need to use the
hda_dma_prepare/cleanup helpers to reserve the pair link host DMA.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.dev>
Link: https://patch.msgid.link/20260203114027.3742558-4-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
SoundWire BPT stream needs to use link and host DMAs. Thus we need
helpers to prepare and cleanup the link and host DMAs. Currently the
SoundWire BPT stream uses hda_cl_prepare/cleanup helpers. It works fine
because we assume the SwoundWire BPT will not run with audio streams
simultaneously. The new helpers are copied from hda_cl_prepare/cleanup
and add a flag to reserve the paired host and link DMAs. The new helpers
will be used by both code loader and SoundWire BPT.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.dev>
Link: https://patch.msgid.link/20260203114027.3742558-3-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Currently, hda_dsp_stream_get/put are used to get/put the host dma.
However, we may want to use a hda stream that both host and link dma are
available. Add helper to find the hda stream and reserve/release it.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.dev>
Link: https://patch.msgid.link/20260203114027.3742558-2-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The link_mask variable is not changed after setting to
hdev->info.link_mask until it is used for another purpose to get the
used SoundWire links and set to mach->mach_params.links. Besides, the
link_mask variable should be reset before any link id is added to the
link_mask. To fix the issue above and avoid confusing, use the
hdev->info.link_mask variable directly to check if the SoundWire link
is enabled.
Fixes: 5226d19d4cae ("ASoC: SOF: Intel: use sof_sdw as default SDW machine driver")
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://patch.msgid.link/20260203072405.3716307-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add support for Nova Lake (NVL).
The core count for NVL is different compared to NVL-S (4 vs 2)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Liam Girdwood <liam.r.girdwood@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20260120193507.14019-3-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The sofdep no longer works due to the reworked HDA audio stack and
it was an incorrect way to try to work around system security
policy blocking request_module use, even if they are legitimate.
Drop the softdep to stop the whack-a-mole hacking around system
configuration issues.
Revert "ASoC: SOF: Intel: hda: add softdep pre to snd-hda-codec-hdmi module"
This reverts commit 33b7dc7843dbdc9b90c91d11ba30b107f9138ffd.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://patch.msgid.link/20260120081935.11005-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Merge series from Sascha Hauer <s.hauer@pengutronix.de>:
These are some patches for the tlv320adcx140 codec we are carrying
around for a while, time to upstream them.
|
|
Replace the manual spinlock lock/unlock pairs with guard().
Only code refactoring, and no behavior change.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://patch.msgid.link/20260112101004.7648-7-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
sense
Replace the manual mutex lock/unlock pairs with guard()/scoped_guard().
Only code refactoring, and no behavior change.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://patch.msgid.link/20260112101004.7648-3-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
